u-boot/arch/arm/mach-at91/spl_at91.c
Wenyou Yang c43a72e88e ARM: at91: clean up the PMC_PLLICPR init code
Due to introducing the PMC_PLLICPR init function, use this
function to clean up the code.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-18 21:34:41 +01:00

134 lines
2.7 KiB
C

/*
* (C) Copyright 2014 DENX Software Engineering
* Heiko Schocher <hs@denx.de>
*
* Based on:
* Copyright (C) 2013 Atmel Corporation
* Bo Shen <voice.shen@atmel.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91sam9_matrix.h>
#include <asm/arch/at91_pit.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/at91_wdt.h>
#include <asm/arch/clk.h>
#include <spl.h>
DECLARE_GLOBAL_DATA_PTR;
static void enable_ext_reset(void)
{
struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
writel(AT91_RSTC_KEY | AT91_RSTC_MR_URSTEN, &rstc->mr);
}
void lowlevel_clock_init(void)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
if (!(readl(&pmc->sr) & AT91_PMC_MOSCS)) {
/* Enable Main Oscillator */
writel(AT91_PMC_MOSCS | (0x40 << 8), &pmc->mor);
/* Wait until Main Oscillator is stable */
while (!(readl(&pmc->sr) & AT91_PMC_MOSCS))
;
}
/* After stabilization, switch to Main Oscillator */
if ((readl(&pmc->mckr) & AT91_PMC_CSS) == AT91_PMC_CSS_SLOW) {
unsigned long tmp;
tmp = readl(&pmc->mckr);
tmp &= ~AT91_PMC_CSS;
tmp |= AT91_PMC_CSS_MAIN;
writel(tmp, &pmc->mckr);
while (!(readl(&pmc->sr) & AT91_PMC_MCKRDY))
;
tmp &= ~AT91_PMC_PRES;
tmp |= AT91_PMC_PRES_1;
writel(tmp, &pmc->mckr);
while (!(readl(&pmc->sr) & AT91_PMC_MCKRDY))
;
}
return;
}
void __weak matrix_init(void)
{
}
void __weak at91_spl_board_init(void)
{
}
void __weak spl_board_init(void)
{
}
void board_init_f(ulong dummy)
{
lowlevel_clock_init();
at91_disable_wdt();
/*
* At this stage the main oscillator is supposed to be enabled
* PCK = MCK = MOSC
*/
at91_pllicpr_init(0x00);
/* Configure PLLA = MOSC * (PLL_MULA + 1) / PLL_DIVA */
at91_plla_init(CONFIG_SYS_AT91_PLLA);
/* PCK = PLLA = 2 * MCK */
at91_mck_init(CONFIG_SYS_MCKR);
/* Switch MCK on PLLA output */
at91_mck_init(CONFIG_SYS_MCKR_CSS);
#if defined(CONFIG_SYS_AT91_PLLB)
/* Configure PLLB */
at91_pllb_init(CONFIG_SYS_AT91_PLLB);
#endif
/* Enable External Reset */
enable_ext_reset();
/* Initialize matrix */
matrix_init();
gd->arch.mck_rate_hz = CONFIG_SYS_MASTER_CLOCK;
/*
* init timer long enough for using in spl.
*/
timer_init();
/* enable clocks for all PIOs */
#if defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9N12)
at91_periph_clk_enable(ATMEL_ID_PIOAB);
at91_periph_clk_enable(ATMEL_ID_PIOCD);
#else
at91_periph_clk_enable(ATMEL_ID_PIOA);
at91_periph_clk_enable(ATMEL_ID_PIOB);
at91_periph_clk_enable(ATMEL_ID_PIOC);
#endif
#if defined(CONFIG_SPL_SERIAL_SUPPORT)
/* init console */
at91_seriald_hw_init();
preloader_console_init();
#endif
mem_init();
at91_spl_board_init();
}