u-boot/include/configs/ADNPESC1.h
Wolfgang Denk 700a0c648d Add common (with Linux) MTD partition scheme and "mtdparts" command
Old, obsolete and duplicated code was cleaned up and replace by the
new partitioning method. There are two possible approaches now:
* define a single, static partition
* use mtdparts command line option and dynamic partitioning
Default is static partitioning.
2005-08-08 01:03:24 +02:00

695 lines
22 KiB
C

/*
* (C) Copyright 2004, Li-Pro.Net <www.li-pro.net>
* Stephan Linz <linz@li-pro.net>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/***********************************************************************
* Include the whole NIOS CPU configuration.
*
* !!! HAVE TO BE HERE !!! DON'T MOVE THIS PART !!!
*
***********************************************************************/
#if defined(CONFIG_NIOS_BASE_32)
#include <configs/ADNPESC1_base_32.h>
#else
#error *** CFG_ERROR: you have to setup right NIOS CPU configuration
#endif
/*------------------------------------------------------------------------
* BOARD/CPU -- TOP-LEVEL
*----------------------------------------------------------------------*/
#define CONFIG_NIOS 1 /* NIOS-32 core */
#define CONFIG_ADNPESC1 1 /* SSV ADNP/ESC1 board */
#define CONFIG_SYS_CLK_FREQ CFG_NIOS_CPU_CLK/* 50 MHz core clock */
#define CFG_HZ 1000 /* 1 msec time tick */
#undef CFG_CLKS_IN_HZ
#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
/*------------------------------------------------------------------------
* BASE ADDRESSES / SIZE (Flash, SRAM, SDRAM)
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_SDRAM_SIZE != 0)
#define CFG_SDRAM_BASE CFG_NIOS_CPU_SDRAM_BASE
#define CFG_SDRAM_SIZE CFG_NIOS_CPU_SDRAM_SIZE
#else
#error *** CFG_ERROR: you have to setup any SDRAM in NIOS CPU config
#endif
#if defined(CFG_NIOS_CPU_SRAM_BASE) && defined(CFG_NIOS_CPU_SRAM_SIZE)
#define CFG_SRAM_BASE CFG_NIOS_CPU_SRAM_BASE
#define CFG_SRAM_SIZE CFG_NIOS_CPU_SRAM_SIZE
#else
#undef CFG_SRAM_BASE
#undef CFG_SRAM_SIZE
#endif
#define CFG_VECT_BASE CFG_NIOS_CPU_VEC_BASE
/*------------------------------------------------------------------------
* MEMORY ORGANIZATION - For the most part, you can put things pretty
* much anywhere. This is pretty flexible for Nios. So here we make some
* arbitrary choices & assume that the monitor is placed at the end of
* a memory resource (so you must make sure TEXT_BASE is chosen
* appropriately -- this is very important if you plan to move your
* memory to another place as configured at this time !!!).
*
* -The heap is placed below the monitor.
* -Global data is placed below the heap.
* -The stack is placed below global data (&grows down).
*----------------------------------------------------------------------*/
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256k */
#define CFG_GBL_DATA_SIZE 128 /* Global data size rsvd*/
#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
#define CFG_GBL_DATA_OFFSET (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP CFG_GBL_DATA_OFFSET
/*------------------------------------------------------------------------
* FLASH (AM29LV065D)
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_FLASH_SIZE != 0)
#define CFG_FLASH_BASE CFG_NIOS_CPU_FLASH_BASE
#define CFG_FLASH_SIZE CFG_NIOS_CPU_FLASH_SIZE
#define CFG_MAX_FLASH_SECT 128 /* Max # sects per bank */
#define CFG_MAX_FLASH_BANKS 1 /* Max # of flash banks */
#define CFG_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */
#define CFG_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */
#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size */
#else
#error *** CFG_ERROR: you have to setup any Flash memory in NIOS CPU config
#endif
/*------------------------------------------------------------------------
* ENVIRONMENT
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_FLASH_SIZE != 0)
#define CFG_ENV_IS_IN_FLASH 1 /* Environment in flash */
/* Mem addr of environment */
#if defined(CONFIG_NIOS_BASE_32)
#define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN)
#else
#error *** CFG_ERROR: you have to setup the environment base address CFG_ENV_ADDR
#endif
#define CFG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */
#define CONFIG_ENV_OVERWRITE /* Serial/eth change Ok */
#else
#define CFG_ENV_IS_NOWHERE 1 /* NO Environment */
#endif
/*------------------------------------------------------------------------
* NIOS APPLICATION CODE BASE AREA
*----------------------------------------------------------------------*/
#if ((CFG_ENV_ADDR + CFG_ENV_SIZE) == 0x1050000)
#define CFG_ADNPESC1_UPDATE_LOAD_ADDR "0x2000100"
#define CFG_ADNPESC1_NIOS_APPL_ENTRY "0x1050000"
#define CFG_ADNPESC1_NIOS_APPL_IDENT "0x105000c"
#define CFG_ADNPESC1_NIOS_APPL_END "0x11fffff"
#define CFG_ADNPESC1_FILESYSTEM_BASE "0x1200000"
#define CFG_ADNPESC1_FILESYSTEM_END "0x17fffff"
#else
#error *** CFG_ERROR: missing right appl.code base configuration, expand your config.h
#endif
#define CFG_ADNPESC1_NIOS_IDENTIFIER "Nios"
/*------------------------------------------------------------------------
* BOOT ENVIRONMENT
*----------------------------------------------------------------------*/
#ifdef CONFIG_DNPEVA2 /* DNP/EVA2 base board */
#define CFG_ADNPESC1_SLED_BOOT_OFF "sled boot off; "
#define CFG_ADNPESC1_SLED_RED_BLINK "sled red blink; "
#else
#define CFG_ADNPESC1_SLED_BOOT_OFF
#define CFG_ADNPESC1_SLED_RED_BLINK
#endif
#define CONFIG_BOOTDELAY 5
#define CONFIG_BOOTCOMMAND \
"if itest.s *$appl_ident_addr == \"$appl_ident_str\"; " \
"then " \
"wd off; " \
CFG_ADNPESC1_SLED_BOOT_OFF \
"go $appl_entry_addr; " \
"else " \
CFG_ADNPESC1_SLED_RED_BLINK \
"echo *** missing \"$appl_ident_str\" at $appl_ident_addr; "\
"echo *** invalid application at $appl_entry_addr; " \
"echo *** stop bootup...; " \
"fi"
/*------------------------------------------------------------------------
* EXTRA ENVIRONMENT
*----------------------------------------------------------------------*/
#ifdef CONFIG_DNPEVA2 /* DNP/EVA2 base board */
#define CFG_ADNPESC1_SLED_YELLO_ON "sled yellow on; "
#define CFG_ADNPESC1_SLED_YELLO_OFF "sled yellow off; "
#else
#define CFG_ADNPESC1_SLED_YELLO_ON
#define CFG_ADNPESC1_SLED_YELLO_OFF
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"update_allowed=0\0" \
"update_load_addr=" CFG_ADNPESC1_UPDATE_LOAD_ADDR "\0" \
"appl_entry_addr=" CFG_ADNPESC1_NIOS_APPL_ENTRY "\0" \
"appl_end_addr=" CFG_ADNPESC1_NIOS_APPL_END "\0" \
"appl_ident_addr=" CFG_ADNPESC1_NIOS_APPL_IDENT "\0" \
"appl_ident_str=" CFG_ADNPESC1_NIOS_IDENTIFIER "\0" \
"appl_name=ADNPESC1/base32/linux.bin\0" \
"appl_update=" \
"if itest.b $update_allowed != 0; " \
"then " \
CFG_ADNPESC1_SLED_YELLO_ON \
"tftp $update_load_addr $appl_name; " \
"protect off $appl_entry_addr $appl_end_addr; " \
"era $appl_entry_addr $appl_end_addr; " \
"cp.b $update_load_addr $appl_entry_addr $filesize; "\
CFG_ADNPESC1_SLED_YELLO_OFF \
"else " \
"echo *** update not allowed (update_allowed=$update_allowed); "\
"fi\0" \
"fs_base_addr=" CFG_ADNPESC1_FILESYSTEM_BASE "\0" \
"fs_end_addr=" CFG_ADNPESC1_FILESYSTEM_END "\0" \
"fs_name=ADNPESC1/base32/romfs.img\0" \
"fs_update=" \
"if itest.b $update_allowed != 0; " \
"then " \
CFG_ADNPESC1_SLED_YELLO_ON \
"tftp $update_load_addr $fs_name; " \
"protect off $fs_base_addr $fs_end_addr; " \
"era $fs_base_addr $fs_end_addr; " \
"cp.b $update_load_addr $fs_base_addr $filesize; "\
CFG_ADNPESC1_SLED_YELLO_OFF \
"else " \
"echo *** update not allowed (update_allowed=$update_allowed); "\
"fi\0" \
"uboot_name=ADNPESC1/base32/u-boot.bin\0" \
"uboot_loadnrun=" \
"if ping $serverip; " \
"then " \
CFG_ADNPESC1_SLED_YELLO_ON \
"tftp $update_load_addr $uboot_name; " \
"wd off; " \
"go $update_load_addr; " \
"else " \
"echo *** missing connection to $serverip; " \
"echo *** check your network and try again...; "\
"fi\0"
/*------------------------------------------------------------------------
* CONSOLE
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_UART_NUMS != 0)
#define CFG_NIOS_CONSOLE CFG_NIOS_CPU_UART0 /* 1st UART is Cons. */
#if (CFG_NIOS_CPU_UART0_BR != 0)
#define CFG_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
#define CONFIG_BAUDRATE CFG_NIOS_CPU_UART0_BR
#else
#undef CFG_NIOS_FIXEDBAUD
#define CONFIG_BAUDRATE 115200
#endif
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#else
#error *** CFG_ERROR: you have to setup at least one UART in NIOS CPU config
#endif
/*------------------------------------------------------------------------
* TIMER FOR TIMEBASE -- Nios doesn't have the equivalent of ppc PIT,
* so an avalon bus timer is required.
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_TIMER_NUMS != 0) && defined(CFG_NIOS_CPU_TICK_TIMER)
#if (CFG_NIOS_CPU_TICK_TIMER == 0)
#define CFG_NIOS_TMRBASE CFG_NIOS_CPU_TIMER0 /* TIMER0 as tick */
#define CFG_NIOS_TMRIRQ CFG_NIOS_CPU_TIMER0_IRQ
#if (CFG_NIOS_CPU_TIMER0_FP == 1) /* fixed period */
#if (CFG_NIOS_CPU_TIMER0_PER >= CFG_HZ)
#define CFG_NIOS_TMRMS (CFG_NIOS_CPU_TIMER0_PER / CFG_HZ)
#else
#error *** CFG_ERROR: you have to use a timer periode greater than CFG_HZ
#endif
#undef CFG_NIOS_TMRCNT /* no preloadable counter value */
#elif (CFG_NIOS_CPU_TIMER0_FP == 0) /* variable period */
#if (CFG_HZ <= 1000)
#define CFG_NIOS_TMRMS (1000 / CFG_HZ)
#else
#error *** CFG_ERROR: sorry, CFG_HZ have to be less than 1000
#endif
#define CFG_NIOS_TMRCNT (CONFIG_SYS_CLK_FREQ / CFG_HZ)
#else
#error *** CFG_ERROR: you have to define CFG_NIOS_CPU_TIMER0_FP correct
#endif
#elif (CFG_NIOS_CPU_TICK_TIMER == 1)
#define CFG_NIOS_TMRBASE CFG_NIOS_CPU_TIMER1 /* TIMER1 as tick */
#define CFG_NIOS_TMRIRQ CFG_NIOS_CPU_TIMER1_IRQ
#if (CFG_NIOS_CPU_TIMER1_FP == 1) /* fixed period */
#if (CFG_NIOS_CPU_TIMER1_PER >= CFG_HZ)
#define CFG_NIOS_TMRMS (CFG_NIOS_CPU_TIMER1_PER / CFG_HZ)
#else
#error *** CFG_ERROR: you have to use a timer periode greater than CFG_HZ
#endif
#undef CFG_NIOS_TMRCNT /* no preloadable counter value */
#elif (CFG_NIOS_CPU_TIMER1_FP == 0) /* variable period */
#if (CFG_HZ <= 1000)
#define CFG_NIOS_TMRMS (1000 / CFG_HZ)
#else
#error *** CFG_ERROR: sorry, CFG_HZ have to be less than 1000
#endif
#define CFG_NIOS_TMRCNT (CONFIG_SYS_CLK_FREQ / CFG_HZ)
#else
#error *** CFG_ERROR: you have to define CFG_NIOS_CPU_TIMER1_FP correct
#endif
#endif /* CFG_NIOS_CPU_TICK_TIMER */
#else
#error *** CFG_ERROR: you have to setup at least one TIMER in NIOS CPU config
#endif
/*------------------------------------------------------------------------
* WATCHDOG (or better MAX823 supervisory circuite access)
*----------------------------------------------------------------------*/
#define CONFIG_HW_WATCHDOG 1 /* board specific WD */
#ifdef CONFIG_HW_WATCHDOG
/* MAX823 supervisor -- watchdog enable port at: */
#if (CFG_NIOS_CPU_WDENA_PIO == 0)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO0 /* PIO0 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 1)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO1 /* PIO1 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 2)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO2 /* PIO2 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 3)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO3 /* PIO3 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 4)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO4 /* PIO4 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 5)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO5 /* PIO5 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 6)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO6 /* PIO6 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 7)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO7 /* PIO7 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 8)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO8 /* PIO8 */
#elif (CFG_NIOS_CPU_WDENA_PIO == 9)
#define CONFIG_HW_WDENA_BASE CFG_NIOS_CPU_PIO9 /* PIO9 */
#else
#error *** CFG_ERROR: you have to setup at least one WDENA_PIO in NIOS CPU config
#endif
/* MAX823 supervisor -- watchdog trigger port at: */
#if (CFG_NIOS_CPU_WDTOG_PIO == 0)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO0 /* PIO0 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 1)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO1 /* PIO1 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 2)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO2 /* PIO2 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 3)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO3 /* PIO3 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 4)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO4 /* PIO4 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 5)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO5 /* PIO5 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 6)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO6 /* PIO6 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 7)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO7 /* PIO7 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 8)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO8 /* PIO8 */
#elif (CFG_NIOS_CPU_WDTOG_PIO == 9)
#define CONFIG_HW_WDTOG_BASE CFG_NIOS_CPU_PIO9 /* PIO9 */
#else
#error *** CFG_ERROR: you have to setup at least one WDTOG_PIO in NIOS CPU config
#endif
#if defined(CONFIG_NIOS_BASE_32) /* NIOS CPU specifics */
#define CONFIG_HW_WDENA_BIT 0 /* WD enable @ Bit 0 */
#define CONFIG_HW_WDTOG_BIT 0 /* WD trigger @ Bit 0 */
#define CONFIG_HW_WDPORT_WRONLY 1 /* each WD port wr/only*/
#else
#error *** CFG_ERROR: missing watchdog bit configuration, expand your config.h
#endif
#endif /* CONFIG_HW_WATCHDOG */
/*------------------------------------------------------------------------
* SERIAL PERIPHAREL INTERFACE
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_SPI_NUMS == 1)
#define CONFIG_NIOS_SPI 1 /* SPI support active */
#define CFG_NIOS_SPIBASE CFG_NIOS_CPU_SPI0
#define CFG_NIOS_SPIBITS CFG_NIOS_CPU_SPI0_BITS
#define CONFIG_RTC_DS1306 1 /* Dallas 1306 real time clock */
#define CFG_SPI_RTC_DEVID 0 /* as 1st SPI device */
#define __SPI_CMD_OFF 0 /* allow default commands: */
/* CFG_CMD_SPI */
/* CFG_CMD_DATE */
#else
#undef CONFIG_NIOS_SPI /* NO SPI support */
#define __SPI_CMD_OFF ( CFG_CMD_SPI \
| CFG_CMD_DATE \
)
#endif
/*------------------------------------------------------------------------
* Ethernet -- needs work!
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_LAN_NUMS == 1)
#if (CFG_NIOS_CPU_LAN0_TYPE == 0) /* LAN91C111 */
#define CONFIG_DRIVER_SMC91111 /* Using SMC91c111 */
#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
#define CONFIG_SMC91111_BASE (CFG_NIOS_CPU_LAN0_BASE + CFG_NIOS_CPU_LAN0_OFFS)
#if (CFG_NIOS_CPU_LAN0_BUSW == 32)
#define CONFIG_SMC_USE_32_BIT 1
#else /* no */
#undef CONFIG_SMC_USE_32_BIT
#endif
#elif (CFG_NIOS_CPU_LAN0_TYPE == 1) /* CS8900A */
/********************************************/
/* !!! CS8900 is __not__ tested on NIOS !!! */
/********************************************/
#define CONFIG_DRIVER_CS8900 /* Using CS8900 */
#define CS8900_BASE (CFG_NIOS_CPU_LAN0_BASE + CFG_NIOS_CPU_LAN0_OFFS)
#if (CFG_NIOS_CPU_LAN0_BUSW == 32)
#undef CS8900_BUS16
#define CS8900_BUS32 1
#else /* no */
#define CS8900_BUS16 1
#undef CS8900_BUS32
#endif
#else
#error *** CFG_ERROR: invalid LAN0 chip type, check your NIOS CPU config
#endif
#define CONFIG_ETHADDR 02:80:ae:20:60:6f
#define CONFIG_NETMASK 255.255.255.248
#define CONFIG_IPADDR 192.168.161.84
#define CONFIG_SERVERIP 192.168.161.85
#else
#error *** CFG_ERROR: you have to setup just one LAN only or expand your config.h
#endif
/*------------------------------------------------------------------------
* STATUS LEDs
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_PIO_NUMS != 0) && defined(CFG_NIOS_CPU_LED_PIO)
#if (CFG_NIOS_CPU_LED_PIO == 0)
#define STATUS_LED_BASE CFG_NIOS_CPU_PIO0
#define STATUS_LED_BITS CFG_NIOS_CPU_PIO0_BITS
#define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
#if (CFG_NIOS_CPU_PIO0_TYPE == 1)
#define STATUS_LED_WRONLY 1
#else
#undef STATUS_LED_WRONLY
#endif
#elif (CFG_NIOS_CPU_LED_PIO == 1)
#define STATUS_LED_BASE CFG_NIOS_CPU_PIO1
#define STATUS_LED_BITS CFG_NIOS_CPU_PIO1_BITS
#define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
#if (CFG_NIOS_CPU_PIO1_TYPE == 1)
#define STATUS_LED_WRONLY 1
#else
#undef STATUS_LED_WRONLY
#endif
#elif (CFG_NIOS_CPU_LED_PIO == 2)
#define STATUS_LED_BASE CFG_NIOS_CPU_PIO2
#define STATUS_LED_BITS CFG_NIOS_CPU_PIO2_BITS
#define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
#if (CFG_NIOS_CPU_PIO2_TYPE == 1)
#define STATUS_LED_WRONLY 1
#else
#undef STATUS_LED_WRONLY
#endif
#elif (CFG_NIOS_CPU_LED_PIO == 3)
#error *** CFG_ERROR: status LEDs at PIO3 not supported, expand your config.h
#elif (CFG_NIOS_CPU_LED_PIO == 4)
#error *** CFG_ERROR: status LEDs at PIO4 not supported, expand your config.h
#elif (CFG_NIOS_CPU_LED_PIO == 5)
#error *** CFG_ERROR: status LEDs at PIO5 not supported, expand your config.h
#elif (CFG_NIOS_CPU_LED_PIO == 6)
#error *** CFG_ERROR: status LEDs at PIO6 not supported, expand your config.h
#elif (CFG_NIOS_CPU_LED_PIO == 7)
#error *** CFG_ERROR: status LEDs at PIO7 not supported, expand your config.h
#elif (CFG_NIOS_CPU_LED_PIO == 8)
#error *** CFG_ERROR: status LEDs at PIO8 not supported, expand your config.h
#elif (CFG_NIOS_CPU_LED_PIO == 9)
#error *** CFG_ERROR: status LEDs at PIO9 not supported, expand your config.h
#else
#error *** CFG_ERROR: you have to set CFG_NIOS_CPU_LED_PIO in right case
#endif
#define CONFIG_STATUS_LED 1 /* enable status led driver */
#define STATUS_LED_BIT (1 << 0) /* LED[0] */
#define STATUS_LED_STATE STATUS_LED_BLINKING
#define STATUS_LED_BOOT_STATE STATUS_LED_OFF
#define STATUS_LED_PERIOD (CFG_HZ / 2) /* ca. 1 Hz */
#define STATUS_LED_BOOT 0 /* boot LED */
#if (STATUS_LED_BITS > 1)
#define STATUS_LED_BIT1 (1 << 1) /* LED[1] */
#define STATUS_LED_STATE1 STATUS_LED_OFF
#define STATUS_LED_PERIOD1 (CFG_HZ / 10) /* ca. 5 Hz */
#define STATUS_LED_RED 1 /* fail LED */
#endif
#if (STATUS_LED_BITS > 2)
#define STATUS_LED_BIT2 (1 << 2) /* LED[2] */
#define STATUS_LED_STATE2 STATUS_LED_OFF
#define STATUS_LED_PERIOD2 (CFG_HZ / 2) /* ca. 1 Hz */
#define STATUS_LED_YELLOW 2 /* info LED */
#endif
#if (STATUS_LED_BITS > 3)
#define STATUS_LED_BIT3 (1 << 3) /* LED[3] */
#define STATUS_LED_STATE3 STATUS_LED_OFF
#define STATUS_LED_PERIOD3 (CFG_HZ / 2) /* ca. 1 Hz */
#define STATUS_LED_GREEN 3 /* info LED */
#endif
#define STATUS_LED_PAR 1 /* makes status_led.h happy */
#endif /* CFG_NIOS_CPU_PIO_NUMS */
/*------------------------------------------------------------------------
* Diagnostics / Power On Self Tests
*----------------------------------------------------------------------*/
#define CONFIG_POST CFG_POST_RTC
#define CFG_NIOS_POST_WORD_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
/*------------------------------------------------------------------------
* COMMANDS
*----------------------------------------------------------------------*/
#define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \
CFG_CMD_ASKENV | \
CFG_CMD_BEDBUG | \
CFG_CMD_BMP | \
CFG_CMD_CACHE | \
CFG_CMD_DOC | \
CFG_CMD_DTT | \
CFG_CMD_EEPROM | \
CFG_CMD_ELF | \
CFG_CMD_FAT | \
CFG_CMD_FDC | \
CFG_CMD_FDOS | \
CFG_CMD_HWFLOW | \
CFG_CMD_IDE | \
CFG_CMD_I2C | \
CFG_CMD_JFFS2 | \
CFG_CMD_KGDB | \
CFG_CMD_NAND | \
CFG_CMD_NFS | \
CFG_CMD_MMC | \
CFG_CMD_MII | \
CFG_CMD_PCI | \
CFG_CMD_PCMCIA | \
CFG_CMD_SCSI | \
CFG_CMD_VFD | \
CFG_CMD_USB | \
CFG_CMD_XIMG | \
__SPI_CMD_OFF ) )
#include <cmd_confdefs.h>
/*------------------------------------------------------------------------
* KGDB
*----------------------------------------------------------------------*/
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 9600
#endif
/*------------------------------------------------------------------------
* MISC
*----------------------------------------------------------------------*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_HUSH_PARSER 1 /* use "hush" command parser
undef to save memory */
#define CFG_PROMPT "ADNPESC1 > " /* Monitor Command Prompt */
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 64 /* max number of command args*/
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "[]> "
#endif
/* Default load address */
#if (CFG_SRAM_SIZE != 0)
/* default in SRAM */
#define CFG_LOAD_ADDR CFG_SRAM_BASE
#elif (CFG_SDRAM_SIZE != 0)
/* default in SDRAM */
#if (CFG_SDRAM_BASE == CFG_NIOS_CPU_VEC_BASE)
#if 1
#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + CFG_NIOS_CPU_VEC_SIZE)
#else
#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x400000)
#endif
#else
#define CFG_LOAD_ADDR CFG_SDRAM_BASE
#endif
#else
#undef CFG_LOAD_ADDR /* force error break */
#endif
/* MEM test area */
#if (CFG_SDRAM_SIZE != 0)
/* SDRAM begin to stack area (1MB stack) */
#if (CFG_SDRAM_BASE == CFG_NIOS_CPU_VEC_BASE)
#if 0
#define CFG_MEMTEST_START (CFG_SDRAM_BASE + CFG_NIOS_CPU_VEC_SIZE)
#else
#define CFG_MEMTEST_START (CFG_SDRAM_BASE + 0x400000)
#endif
#else
#define CFG_MEMTEST_START CFG_SDRAM_BASE
#endif
#define CFG_MEMTEST_END (CFG_INIT_SP - (1024 * 1024))
#define CFG_MEMTEST_END (CFG_INIT_SP - (1024 * 1024))
#else
#undef CFG_MEMTEST_START /* force error break */
#undef CFG_MEMTEST_END
#endif
/*
* JFFS2 partitions
*
*/
/* No command line, one static partition */
#undef CONFIG_JFFS2_CMDLINE
#define CONFIG_JFFS2_DEV "nor"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
/*
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT ""
#define MTDPARTS_DEFAULT ""
*/
#endif /* __CONFIG_H */