u-boot/include/configs/eXalion.h
wdenk 132ba5fdc5 * Patch by Pierre Aubert, 26 Feb 2004
add IDE support for MPC5200

* Patch by Masami Komiya, 26 Feb 2004:
  add autoload via NFS

* Patch by Stephen Williams
  Use of CONFIG_SERIAL_SOFTWARE_FIFO in board.c consistent with uses
  elsewhere in the source.
2004-02-27 08:20:54 +00:00

455 lines
15 KiB
C

/*
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/* ------------------------------------------------------------------------- */
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC824X 1
/* #define CONFIG_MPC8240 1 */
#define CONFIG_MPC8245 1
#define CONFIG_EXALION 1
#if defined (CONFIG_MPC8240)
/* #warning ---------- eXalion with MPC8240 --------------- */
#elif defined (CONFIG_MPC8245)
/* #warning ++++++++++ eXalion with MPC8245 +++++++++++++++ */
#elif defined (CONFIG_MPC8245) && defined (CONFIG_MPC8245)
#error #### Both types of MPC824x defined (CONFIG_8240 and CONFIG_8245)
#else
#error #### Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
#endif
/* older kernels need clock in MHz newer in Hz */
/* #define CONFIG_CLOCKS_IN_MHZ 1 */ /* clocks passsed to Linux in MHz */
#undef CONFIG_CLOCKS_IN_MHZ
#define CONFIG_BOOTDELAY 10
/*#define CONFIG_DRAM_SPEED 66 */ /* MHz */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_FLASH | \
CFG_CMD_SDRAM | \
CFG_CMD_I2C | \
CFG_CMD_IDE | \
CFG_CMD_FAT | \
CFG_CMD_ENV | \
CFG_CMD_PCI )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*/
#define CFG_LONGHELP 1 /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 8 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_LOAD_ADDR 0x00100000 /* default load address */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_MISC_INIT_R 1
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_MAX_RAM_SIZE 0x10000000 /* 1 GBytes - initdram() will */
/* return real value. */
#define CFG_RESET_ADDRESS 0xFFF00100
#undef CFG_RAMBOOT
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MONITOR_BASE TEXT_BASE
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area
*/
#define CFG_INIT_DATA_SIZE 128
#define CFG_INIT_RAM_ADDR 0x40000000
#define CFG_INIT_RAM_END 0x1000
#define CFG_INIT_DATA_OFFSET (CFG_INIT_RAM_END - CFG_INIT_DATA_SIZE)
#define CFG_GBL_DATA_SIZE 256 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#if defined (CONFIG_MPC8240)
#define CFG_FLASH_BASE 0xFFE00000
#define CFG_FLASH_SIZE (2 * 1024 * 1024) /* onboard 2MByte flash */
#elif defined (CONFIG_MPC8245)
#define CFG_FLASH_BASE 0xFFC00000
#define CFG_FLASH_SIZE (4 * 1024 * 1024) /* onboard 4MByte flash */
#else
#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
#endif
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_SECT_SIZE 0x20000 /* Size of one Flash sector */
#define CFG_ENV_SIZE CFG_ENV_SECT_SIZE /* Use one Flash sector for enviroment */
#define CFG_ENV_ADDR 0xFFFC0000
#define CFG_ENV_OFFSET 0 /* starting right at the beginning */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
#define CFG_ALT_MEMTEST 1 /* use real memory test */
#define CFG_MEMTEST_START 0x00004000 /* memtest works on */
#define CFG_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
#define CFG_EUMB_ADDR 0xFC000000
/* #define CFG_ISA_MEM 0xFD000000 */
#define CFG_ISA_IO 0xFE000000
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */
#define CFG_MAX_FLASH_SECT 64 /* Max number of sectors per flash */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define FLASH_BASE0_PRELIM CFG_FLASH_BASE
#define FLASH_BASE1_PRELIM 0
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_FLASH_INCREMENT 0 /* there is only one bank */
#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
/*-----------------------------------------------------------------------
* PCI stuff
*/
#define CONFIG_PCI 1 /* include pci support */
#undef CONFIG_PCI_PNP
#define CONFIG_NET_MULTI 1 /* Multi ethernet cards support */
#define CONFIG_EEPRO100 1
#define PCI_ENET0_MEMADDR 0x80000000 /* Intel 82559ER */
#define PCI_ENET0_IOADDR 0x80000000
#define PCI_ENET1_MEMADDR 0x81000000 /* Intel 82559ER */
#define PCI_ENET1_IOADDR 0x81000000
#define PCI_ENET2_MEMADDR 0x82000000 /* Broadcom BCM569xx */
#define PCI_ENET2_IOADDR 0x82000000
#define PCI_ENET3_MEMADDR 0x83000000 /* Broadcom BCM56xx */
#define PCI_ENET3_IOADDR 0x83000000
/*-----------------------------------------------------------------------
* NS16550 Configuration
*/
#define CFG_NS16550 1
#define CFG_NS16550_SERIAL 1
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 38400
#define CFG_NS16550_REG_SIZE 1
#if (CONFIG_CONS_INDEX == 1)
#define CFG_NS16550_CLK 1843200 /* COM1 only ! */
#else
#define CFG_NS16550_CLK ({ extern ulong get_bus_freq (ulong); get_bus_freq (0); })
#endif
#define CFG_NS16550_COM1 (CFG_ISA_IO + 0x3F8)
#define CFG_NS16550_COM2 (CFG_EUMB_ADDR + 0x4500)
#define CFG_NS16550_COM3 (CFG_EUMB_ADDR + 0x4600)
/*-----------------------------------------------------------------------
* select i2c support configuration
*
* Supported configurations are {none, software, hardware} drivers.
* If the software driver is chosen, there are some additional
* configuration items that the driver uses to drive the port pins.
*/
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
/*-----------------------------------------------------------------------
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CFG_HZ 1000
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2 /* for MPC8240 only */
/*#define CONFIG_133MHZ_DRAM 1 */ /* For 133 MHZ DRAM only !!!!!!!!!!! */
#if defined (CONFIG_MPC8245)
/* Bit-field values for PMCR2. */
#if defined (CONFIG_133MHZ_DRAM)
#define CFG_DLL_EXTEND 0x80 /* use DLL extended range - 133MHz only */
#define CFG_PCI_HOLD_DEL 0x20 /* delay and hold timing - 133MHz only */
#endif
/* Bit-field values for MIOCR1. */
#if !defined (CONFIG_133MHZ_DRAM)
#define CFG_DLL_MAX_DELAY 0x04 /* longer DLL delay line - 66MHz only */
#endif
/* Bit-field values for MIOCR2. */
#define CFG_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay */
/* - note bottom 3 bits MUST be 0 */
#endif
/* Bit-field values for MCCR1. */
#define CFG_ROMNAL 7 /*rom/flash next access time */
#define CFG_ROMFAL 11 /*rom/flash access time */
/* Bit-field values for MCCR2. */
#define CFG_TSWAIT 0x5 /* Transaction Start Wait States timer */
#if defined (CONFIG_133MHZ_DRAM)
#define CFG_REFINT 1300 /* no of clock cycles between CBR */
#else /* refresh cycles */
#define CFG_REFINT 750
#endif
/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
#if defined (CONFIG_133MHZ_DRAM)
#define CFG_BSTOPRE 1023
#else
#define CFG_BSTOPRE 250
#endif
/* Bit-field values for MCCR3. */
/* the following are for SDRAM only */
#if defined (CONFIG_133MHZ_DRAM)
#define CFG_REFREC 9 /* Refresh to activate interval */
#else
#define CFG_REFREC 5 /* Refresh to activate interval */
#endif
#if defined (CONFIG_MPC8240)
#define CFG_RDLAT 2 /* data latency from read command */
#endif
/* Bit-field values for MCCR4. */
#if defined (CONFIG_133MHZ_DRAM)
#define CFG_PRETOACT 3 /* Precharge to activate interval */
#define CFG_ACTTOPRE 7 /* Activate to Precharge interval */
#define CFG_ACTORW 5 /* Activate to R/W */
#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
#else
#if 0
#define CFG_PRETOACT 2 /* Precharge to activate interval */
#define CFG_ACTTOPRE 3 /* Activate to Precharge interval */
#define CFG_ACTORW 3 /* Activate to R/W */
#define CFG_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */
#endif
#define CFG_PRETOACT 2 /* Precharge to activate interval */
#define CFG_ACTTOPRE 5 /* Activate to Precharge interval */
#define CFG_ACTORW 3 /* Activate to R/W */
#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
#endif
#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */
#define CFG_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */
#define CFG_REGDIMM 0
#if defined (CONFIG_MPC8240)
#define CFG_REGISTERD_TYPE_BUFFER 0
#elif defined (CONFIG_MPC8245)
#define CFG_REGISTERD_TYPE_BUFFER 1
#define CFG_EXTROM 0
#else
#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
#endif
/*-----------------------------------------------------------------------
memory bank settings
* only bits 20-29 are actually used from these vales to set the
* start/end address the upper two bits will be 0, and the lower 20
* bits will be set to 0x00000 for a start address, or 0xfffff for an
* end address
*/
#define CFG_BANK0_START 0x00000000
#define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1)
#define CFG_BANK0_ENABLE 1
#define CFG_BANK1_START 0x3ff00000
#define CFG_BANK1_END 0x3fffffff
#define CFG_BANK1_ENABLE 0
#define CFG_BANK2_START 0x3ff00000
#define CFG_BANK2_END 0x3fffffff
#define CFG_BANK2_ENABLE 0
#define CFG_BANK3_START 0x3ff00000
#define CFG_BANK3_END 0x3fffffff
#define CFG_BANK3_ENABLE 0
#define CFG_BANK4_START 0x00000000
#define CFG_BANK4_END 0x00000000
#define CFG_BANK4_ENABLE 0
#define CFG_BANK5_START 0x00000000
#define CFG_BANK5_END 0x00000000
#define CFG_BANK5_ENABLE 0
#define CFG_BANK6_START 0x00000000
#define CFG_BANK6_END 0x00000000
#define CFG_BANK6_ENABLE 0
#define CFG_BANK7_START 0x00000000
#define CFG_BANK7_END 0x00000000
#define CFG_BANK7_ENABLE 0
/*-----------------------------------------------------------------------
* Memory bank enable bitmask, specifying which of the banks defined above
are actually present. MSB is for bank #7, LSB is for bank #0.
*/
#define CFG_BANK_ENABLE 0x01
#if defined (CONFIG_MPC8240)
#define CFG_ODCR 0xDF /* configures line driver impedances, */
/* see 8240 book for bit definitions */
#elif defined (CONFIG_MPC8245)
#if defined (CONFIG_133MHZ_DRAM)
#define CFG_ODCR 0xFE /* configures line driver impedances - 133MHz */
#else
#define CFG_ODCR 0xDE /* configures line driver impedances - 66MHz */
#endif
#else
#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
#endif
#define CFG_PGMAX 0x32 /* how long the 8240 retains the */
/* currently accessed page in memory */
/* see 8240 book for details */
/*-----------------------------------------------------------------------
* Block Address Translation (BAT) register settings.
*/
/* SDRAM 0 - 256MB */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
/* stack in DCACHE @ 1GB (no backing mem) */
#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
/* PCI memory */
#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
/* Flash, config addrs, etc */
#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_DBAT0L CFG_IBAT0L
#define CFG_DBAT0U CFG_IBAT0U
#define CFG_DBAT1L CFG_IBAT1L
#define CFG_DBAT1U CFG_IBAT1U
#define CFG_DBAT2L CFG_IBAT2L
#define CFG_DBAT2U CFG_IBAT2U
#define CFG_DBAT3L CFG_IBAT3L
#define CFG_DBAT3U CFG_IBAT3U
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
/* values according to the manual */
#define CONFIG_DRAM_50MHZ 1
#define CONFIG_SDRAM_50MHZ
#undef NR_8259_INTS
#define NR_8259_INTS 1
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*/
#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */
#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 2 drives per IDE bus */
#define CFG_ATA_BASE_ADDR CFG_ISA_IO /* base address */
#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */
#define CFG_ATA_REG_OFFSET 0 /* reg offset */
#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
#define CONFIG_ATAPI
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* reset for ide supported... */
#undef CONFIG_IDE_RESET_ROUTINE /* with a special reset function */
/*-----------------------------------------------------------------------
* DISK Partition support
*/
#define CONFIG_DOS_PARTITION
/*-----------------------------------------------------------------------
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#endif /* __CONFIG_H */