u-boot/include/configs/bf609-ezkit.h
Sonic Zhang da34aae5fb bfin: Move gpio support for bf54x and bf60x into the generic driver folder.
The gpio spec for bf54x and bf60x differ a lot from the old gpio driver for bf5xx.
A lot of machine macros are used to accomodate both code in one gpio driver.
This patch split the old gpio driver and move new gpio2 support to the generic
gpio driver folder.

- To enable gpio2 driver, macro CONFIG_ADI_GPIO2 should be defined in the board's
config header file.
- The gpio2 driver supports bf54x, bf60x and future ADI processors, while the
older gpio driver supports bf50x, bf51x, bf52x, bf53x and bf561.
- All blackfin specific gpio function names are replaced by the generic gpio APIs.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13 16:30:27 +08:00

173 lines
4.3 KiB
C

/*
* U-boot - Configuration file for BF609 EZ-Kit board
*/
#ifndef __CONFIG_BF609_EZKIT_H__
#define __CONFIG_BF609_EZKIT_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf609-0.0
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA
/* For ez-board version 1.0, else undef this */
#define CONFIG_BFIN_BOARD_VERSION_1_0
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SYSCLK_DIV
* SCLK0 = SCLK / SCLK0_DIV
* SCLK1 = SCLK / SCLK1_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ (25000000)
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF (0)
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-127 (where 0 means 128) */
#define CONFIG_VCO_MULT (20)
/* CCLK_DIV controls the core clock divider */
/* Values can range from 0-31 (where 0 means 32) */
#define CONFIG_CCLK_DIV (1)
/* SCLK_DIV controls the system clock divider */
/* Values can range from 0-31 (where 0 means 32) */
#define CONFIG_SCLK_DIV (4)
/* Values can range from 0-7 (where 0 means 8) */
#define CONFIG_SCLK0_DIV (1)
#define CONFIG_SCLK1_DIV (1)
/* DCLK_DIV controls the DDR clock divider */
/* Values can range from 0-31 (where 0 means 32) */
#define CONFIG_DCLK_DIV (2)
/* OCLK_DIV controls the output clock divider */
/* Values can range from 0-127 (where 0 means 128) */
#define CONFIG_OCLK_DIV (16)
/*
* Memory Settings
*/
#define CONFIG_MEM_SIZE 128
#define CONFIG_SMC_GCTL_VAL 0x00000010
#define CONFIG_SMC_B0CTL_VAL 0x01007011
#define CONFIG_SMC_B0TIM_VAL 0x08170977
#define CONFIG_SMC_B0ETIM_VAL 0x00092231
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
#define CONFIG_HW_WATCHDOG
/*
* Network Settings
*/
#define ADI_CMDS_NETWORK
#define CONFIG_NETCONSOLE
#define CONFIG_NET_MULTI
#define CONFIG_HOSTNAME "bf609-ezkit"
#define CONFIG_DESIGNWARE_ETH
#define CONFIG_DW_PORTS 1
#define CONFIG_DW_AUTONEG
#define CONFIG_DW_ALTDESCRIPTOR
#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_MII
/* i2c Settings */
#define CONFIG_BFIN_TWI_I2C
#define CONFIG_HARD_I2C
/*
* Flash Settings
*/
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_JFFS2
#define CONFIG_SYS_FLASH_CFI_WIDTH 2
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_BASE 0xb0000000
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 131
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
/*
* SPI Settings
*/
#define CONFIG_BFIN_SPI6XX
#define CONFIG_ENV_SPI_MAX_HZ 25000000
#define CONFIG_SF_DEFAULT_SPEED 25000000
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_ALL
/*
* Env Storage Settings
*/
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET 0x10000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
#elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x60000
#define CONFIG_ENV_SIZE 0x20000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_OFFSET 0x8000
#define CONFIG_ENV_SIZE 0x8000
#define CONFIG_ENV_SECT_SIZE 0x8000
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
#endif
#define FLASHBOOT_ENV_SETTINGS "flashboot=bootm 0xB0100000\0"
/*
* SDH Settings
*/
#define CONFIG_GENERIC_MMC
#define CONFIG_MMC
#define CONFIG_BFIN_SDH
/*
* Misc Settings
*/
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_UART_CONSOLE 0
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_SOFTSWITCH
#define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 20*1024*1024 + 4)
#define CONFIG_BFIN_SOFT_SWITCH
#define CONFIG_ADI_GPIO2
#if 0
#define CONFIG_UART_MEM 1024
#undef CONFIG_UART_CONSOLE
#undef CONFIG_JTAG_CONSOLE
#undef CONFIG_UART_CONSOLE_IS_JTAG
#endif
#define CONFIG_BOARD_SIZE_LIMIT $$((512 * 1024))
/*
* Run core 1 from L1 SRAM start address when init uboot on core 0
*/
/* #define CONFIG_CORE1_RUN 1 */
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif