u-boot/include/configs/v37.h
wdenk 2535d60277 * Patch by Martin Krause, 17 Jul 2003:
add delay to get I2C working with "imm" command and s3c24x0_i2c.c

* Patch by Richard Woodruff, 17 July 03:
  - Fixed bug in OMAP1510 baud rate divisor settings.

* Patch by Nye Liu, 16 July 2003:
  MPC860FADS fixes:
  - add MPC86xADS support (uses MPC86xADS.h)
  - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
    o PLPRCR changes
    o BRG changes (EXTAL/XTAL restricted to 10MHz)
    o don't trust gclk() software measurement by default, depend on
      CONFIG_8xx_GCLK_FREQ
  - add DRAM SIMM not installed detection
  - use more "correct" SDRAM initialization sequence
  - allow different SDRAM sizes (8xxADS has 8M)
  - default DER is 0
  - remove unused MAMR defines from FADS860T.h (all done in fads.c)
  - rename MAMR/MBMR defines to be more consistent. Should eventually
    be merged into MxMR to better reflect the PowerQUICC datasheet.

* Patch by Yuli Barcohen, 16 Jul 2003:
  support new Motorola PQ2FADS-ZU evaluation board which replaced
  MPC8260ADS and MPC8266ADS
2003-07-17 23:16:40 +00:00

379 lines
12 KiB
C

/*
* (C) Copyright 2000, 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
#define CONFIG_V37 1 /* ...on a Marel V37 board */
#define CONFIG_LCD
#define CONFIG_SHARP_LQ084V1DG21
#undef CONFIG_LCD_LOGO
/*-----------------------------------------------------------------------------
* I2C Configuration
*-----------------------------------------------------------------------------
*/
#define CONFIG_I2C 1
#define CFG_I2C_SLAVE 0x2
#define CONFIG_8xx_CONS_SMC1 1
#undef CONFIG_8xx_CONS_SMC2 /* Console is on SMC2 */
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 9600 /* console baudrate = 115kbps */
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
#endif
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"tftpboot; " \
"setenv bootargs console=tty0 " \
"root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
"bootm"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_CAN_DRIVER 1 /* CAN Driver support enabled */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_JFFS2 | \
CFG_CMD_DATE )
/* Flash banks JFFS2 should use */
#define CFG_JFFS2_FIRST_BANK 1
#define CFG_JFFS2_NUM_BANKS 1
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CFG_IMMR 0xF0000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE0 0x40000000
#define CFG_FLASH_BASE1 0x60000000
#define CFG_FLASH_BASE CFG_FLASH_BASE1
#if defined(DEBUG)
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#endif
#define CFG_MONITOR_BASE CFG_FLASH_BASE0
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_ENV_IS_IN_NVRAM 1
#define CFG_ENV_ADDR 0x80000000/* Address of Environment */
#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
#define CFG_ENV_OFFSET 0
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CFG_SYPCR 0xFFFFFF88
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_FRC | SIUMCR_GB5E)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
/*%%%#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
#define CFG_RTCSC (RTCSC_SEC | RTCSC_RTE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
/*
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
*/
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit
*
* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
*/
/* up to 50 MHz we use a 1:1 clock */
#define CFG_PLPRCR ( (1524 << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TMIST | PLPRCR_TEXPS )
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
/* up to 50 MHz we use a 1:1 clock */
#define CFG_SCCR (SCCR_COM00 | SCCR_TBS)
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*
*/
#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
#define CFG_PCMCIA_IO_ADDR (0xEC000000)
#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_PCCARD /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_PCMCIA /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
/* Offset for data I/O */
#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
/* Offset for normal register accesses */
#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
/* Offset for alternate registers */
#define CFG_ATA_ALT_OFFSET 0x0100
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
#define CFG_DER 0
/*
* Init Memory Controller:
*
* BR0 and OR0 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #1 */
#define CFG_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
#define CFG_OR_TIMING_FLASH 0xF56
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V)
#define CFG_OR5_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR5_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V)
/*
* BR1 and OR1 (Battery backed SRAM)
*/
#define CFG_BR1_PRELIM 0x80000401
#define CFG_OR1_PRELIM 0xFFC00736
/*
* BR2 and OR2 (SDRAM)
*/
#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB */
#define CFG_OR_TIMING_SDRAM 0x00000A00
#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
#define CFG_BR2_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
/* Marel V37 mem setting */
#define CFG_BR3_CAN 0xC0000401
#define CFG_OR3_CAN 0xFFFF0724
/*
#define CFG_BR3_PRELIM 0xFA400001
#define CFG_OR3_PRELIM 0xFFFF8910
#define CFG_BR4_PRELIM 0xFA000401
#define CFG_OR4_PRELIM 0xFFFE0970
*/
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
/*
* Refresh clock Prescalar
*/
#define CFG_MPTPR MPTPR_PTP_DIV16
/*
* MAMR settings for SDRAM
*/
/* 10 column SDRAM */
#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \
MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#endif /* __CONFIG_H */