u-boot/board/ti/omap730p2/lowlevel_init.S
Wolfgang Denk 14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00

396 lines
8.8 KiB
ArmAsm

/*
* Board specific setup info
*
* (C) Copyright 2003-2004
*
* Texas Instruments, <www.ti.com>
* Kshitij Gupta <Kshitij@ti.com>
*
* Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
*
* Modified for OMAP730 P2 Board by Dave Peverley, MPC-Data Limited
* (http://www.mpc-data.co.uk)
*
* TODO : Tidy up and change to use system register defines
* from omap730.h where possible.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <config.h>
#include <version.h>
#if defined(CONFIG_OMAP730)
#include <./configs/omap730.h>
#endif
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE /* sdram load addr from config.mk */
.globl lowlevel_init
lowlevel_init:
/* Save callers address in r11 - r11 must never be modified */
mov r11, lr
/*------------------------------------------------------*
*mask all IRQs by setting all bits in the INTMR default*
*------------------------------------------------------*/
mov r1, #0xffffffff
ldr r0, =REG_IHL1_MIR
str r1, [r0]
ldr r0, =REG_IHL2_MIR
str r1, [r0]
/*------------------------------------------------------*
* Set up ARM CLM registers (IDLECT1) *
*------------------------------------------------------*/
ldr r0, REG_ARM_IDLECT1
ldr r1, VAL_ARM_IDLECT1
str r1, [r0]
/*------------------------------------------------------*
* Set up ARM CLM registers (IDLECT2) *
*------------------------------------------------------*/
ldr r0, REG_ARM_IDLECT2
ldr r1, VAL_ARM_IDLECT2
str r1, [r0]
/*------------------------------------------------------*
* Set up ARM CLM registers (IDLECT3) *
*------------------------------------------------------*/
ldr r0, REG_ARM_IDLECT3
ldr r1, VAL_ARM_IDLECT3
str r1, [r0]
mov r1, #0x01 /* PER_EN bit */
ldr r0, REG_ARM_RSTCT2
strh r1, [r0] /* CLKM; Peripheral reset. */
/* Set CLKM to Sync-Scalable */
/* I supposedly need to enable the dsp clock before switching */
mov r1, #0x1000
ldr r0, REG_ARM_SYSST
strh r1, [r0]
mov r0, #0x400
1:
subs r0, r0, #0x1 /* wait for any bubbles to finish */
bne 1b
ldr r1, VAL_ARM_CKCTL
ldr r0, REG_ARM_CKCTL
strh r1, [r0]
/* a few nops to let settle */
nop
nop
nop
nop
nop
nop
nop
nop
nop
nop
/* setup DPLL 1 */
/* Ramp up the clock to 96Mhz */
ldr r1, VAL_DPLL1_CTL
ldr r0, REG_DPLL1_CTL
strh r1, [r0]
ands r1, r1, #0x10 /* Check if PLL is enabled. */
beq lock_end /* Do not look for lock if BYPASS selected */
2:
ldrh r1, [r0]
ands r1, r1, #0x01 /* Check the LOCK bit.*/
beq 2b /* loop until bit goes hi. */
lock_end:
/*------------------------------------------------------*
* Turn off the watchdog during init... *
*------------------------------------------------------*/
ldr r0, REG_WATCHDOG
ldr r1, WATCHDOG_VAL1
str r1, [r0]
ldr r1, WATCHDOG_VAL2
str r1, [r0]
ldr r0, REG_WSPRDOG
ldr r1, WSPRDOG_VAL1
str r1, [r0]
ldr r0, REG_WWPSDOG
watch1Wait:
ldr r1, [r0]
tst r1, #0x10
bne watch1Wait
ldr r0, REG_WSPRDOG
ldr r1, WSPRDOG_VAL2
str r1, [r0]
ldr r0, REG_WWPSDOG
watch2Wait:
ldr r1, [r0]
tst r1, #0x10
bne watch2Wait
/* Set memory timings corresponding to the new clock speed */
/* Check execution location to determine current execution location
* and branch to appropriate initialization code.
*/
/* Compare physical SDRAM base & current execution location. */
and r0, pc, #0xF0000000
/* Compare. */
cmp r0, #0
/* Skip over EMIF-fast initialization if running from SDRAM. */
bne skip_sdram
/*
* Delay for SDRAM initialization.
*/
mov r3, #0x1800 /* value should be checked */
3:
subs r3, r3, #0x1 /* Decrement count */
bne 3b
ldr r0, REG_SDRAM_CONFIG
ldr r1, SDRAM_CONFIG_VAL
str r1, [r0]
ldr r0, REG_SDRAM_MRS_LEGACY
ldr r1, SDRAM_MRS_VAL
str r1, [r0]
skip_sdram:
common_tc:
/* slow interface */
ldr r1, VAL_TC_EMIFS_CS0_CONFIG
ldr r0, REG_TC_EMIFS_CS0_CONFIG
str r1, [r0] /* Chip Select 0 */
ldr r1, VAL_TC_EMIFS_CS1_CONFIG
ldr r0, REG_TC_EMIFS_CS1_CONFIG
str r1, [r0] /* Chip Select 1 */
ldr r1, VAL_TC_EMIFS_CS2_CONFIG
ldr r0, REG_TC_EMIFS_CS2_CONFIG
str r1, [r0] /* Chip Select 2 */
ldr r1, VAL_TC_EMIFS_CS3_CONFIG
ldr r0, REG_TC_EMIFS_CS3_CONFIG
str r1, [r0] /* Chip Select 3 */
/* 48MHz clock request for UART1 */
ldr r1, PERSEUS2_CONFIG_BASE
ldrh r0, [r1, #CONFIG_PCC_CONF]
orr r0, r0, #CONF_MOD_UART1_CLK_MODE_R
strh r0, [r1, #CONFIG_PCC_CONF]
/* Initialize public and private rheas
* - set access factor 2 on both rhea / strobe
* - disable write buffer on strb0, enable write buffer on strb1
*/
ldr R0, REG_RHEA_PUB_CTL
ldr R1, REG_RHEA_PRIV_CTL
ldr R2, VAL_RHEA_CTL
strh R2, [R0]
strh R2, [R1]
mov R3, #2 /* disable write buffer on strb0, enable write buffer on strb1 */
strh R3, [R0, #0x08] /* arm rhea control reg */
strh R3, [R1, #0x08]
/* enable IRQ and FIQ */
mrs r4, CPSR
bic r4, r4, #IRQ_MASK
bic r4, r4, #FIQ_MASK
msr CPSR, r4
/* set TAP CONF to TRI EMULATION */
ldr r1, [r0, #CONFIG_MODE2]
bic r1, r1, #0x18
orr r1, r1, #0x10
str r1, [r0, #CONFIG_MODE2]
/* set tdbgen to 1 */
ldr r0, PERSEUS2_CONFIG_BASE
ldr r1, [r0, #CONFIG_MODE1]
mov r2, #0x10000
orr r1, r1, r2
str r1, [r0, #CONFIG_MODE1]
#ifdef CONFIG_P2_OMAP1610
/* inserting additional 2 clock cycle hold time for LAN */
ldr r0, REG_TC_EMIFS_CS1_ADVANCED
ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
str r1, [r0]
#endif
/* Start MPU Timer 1 */
ldr r0, REG_MPU_LOAD_TIMER
ldr r1, VAL_MPU_LOAD_TIMER
str r1, [r0]
ldr r0, REG_MPU_CNTL_TIMER
ldr r1, VAL_MPU_CNTL_TIMER
str r1, [r0]
/* back to arch calling code */
mov pc, r11
/* the literal pools origin */
.ltorg
REG_TC_EMIFS_CONFIG: /* 32 bits */
.word 0xfffecc0c
REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
.word 0xfffecc10
REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
.word 0xfffecc14
REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
.word 0xfffecc18
REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
.word 0xfffecc1c
#ifdef CONFIG_P2_OMAP730
REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
.word 0xfffecc54
#endif
/* MPU clock/reset/power mode control registers */
REG_ARM_CKCTL: /* 16 bits */
.word 0xfffece00
REG_ARM_IDLECT3: /* 16 bits */
.word 0xfffece24
REG_ARM_IDLECT2: /* 16 bits */
.word 0xfffece08
REG_ARM_IDLECT1: /* 16 bits */
.word 0xfffece04
REG_ARM_RSTCT2: /* 16 bits */
.word 0xfffece14
REG_ARM_SYSST: /* 16 bits */
.word 0xfffece18
/* DPLL control registers */
REG_DPLL1_CTL: /* 16 bits */
.word 0xfffecf00
/* Watch Dog register */
/* secure watchdog stop */
REG_WSPRDOG:
.word 0xfffeb048
/* watchdog write pending */
REG_WWPSDOG:
.word 0xfffeb034
WSPRDOG_VAL1:
.word 0x0000aaaa
WSPRDOG_VAL2:
.word 0x00005555
/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
counter @8192 rows, 10 ns, 8 burst */
REG_SDRAM_CONFIG:
.word 0xfffecc20
REG_SDRAM_MRS_LEGACY:
.word 0xfffecc24
REG_WATCHDOG:
.word 0xfffec808
REG_MPU_LOAD_TIMER:
.word 0xfffec504
REG_MPU_CNTL_TIMER:
.word 0xfffec500
/* Public and private rhea bridge registers definition */
REG_RHEA_PUB_CTL:
.word 0xFFFECA00
REG_RHEA_PRIV_CTL:
.word 0xFFFED300
/* EMIFF SDRAM Configuration register
- self refresh disable
- auto refresh enabled
- SDRAM type 64 Mb, 16 bits bus 4 banks
- power down enabled
- SDRAM clock disabled
*/
SDRAM_CONFIG_VAL:
.word 0x0C017DF4
/* Burst full page length ; cas latency = 3 */
SDRAM_MRS_VAL:
.word 0x00000037
VAL_ARM_CKCTL:
.word 0x6505
VAL_DPLL1_CTL:
.word 0x3412
#ifdef CONFIG_P2_OMAP730
VAL_TC_EMIFS_CS0_CONFIG:
.word 0x0000FFF3
VAL_TC_EMIFS_CS1_CONFIG:
.word 0x00004278
VAL_TC_EMIFS_CS2_CONFIG:
.word 0x00004278
VAL_TC_EMIFS_CS3_CONFIG:
.word 0x00004278
VAL_TC_EMIFS_CS1_ADVANCED:
.word 0x00000022
#endif
VAL_ARM_IDLECT1:
.word 0x00000400
VAL_ARM_IDLECT2:
.word 0x00000886
VAL_ARM_IDLECT3:
.word 0x00000015
WATCHDOG_VAL1:
.word 0x000000f5
WATCHDOG_VAL2:
.word 0x000000a0
VAL_MPU_LOAD_TIMER:
.word 0xffffffff
VAL_MPU_CNTL_TIMER:
.word 0xffffffa1
VAL_RHEA_CTL:
.word 0xFF22
/* Config Register vals */
PERSEUS2_CONFIG_BASE:
.word 0xFFFE1000
.equ CONFIG_PCC_CONF, 0xB4
.equ CONFIG_MODE1, 0x10
.equ CONFIG_MODE2, 0x14
.equ CONF_MOD_UART1_CLK_MODE_R, 0x0A
/* misc values */
.equ IRQ_MASK, 0x80 /* IRQ mask value */
.equ FIQ_MASK, 0x40 /* FIQ mask value */