u-boot/include/configs/NC650.h
wdenk 07cc099941 Major upate of JFFS2 code; now in sync with snapshot of MTD CVS of
March 13, 2005); new configuration options CONFIG_JFFS2_LZO and
CONFIG_JFFS2_LZARI are added. Both are undefined by default.
2005-05-05 00:04:14 +00:00

409 lines
13 KiB
C

/*
* (C) Copyright 2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC852T 1
#define CONFIG_NC650 1
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
/*
* 10 MHz - PLL input clock
*/
#define CONFIG_8xx_OSCLK 10000000
/*
* 50 MHz - default CPU clock
*/
#define CONFIG_8xx_CPUCLK_DEFAULT 50000000
/*
* 15 MHz - CPU minimum clock
*/
#define CFG_8xx_CPUCLK_MIN 15000000
/*
* 133 MHz - CPU maximum clock
*/
#define CFG_8xx_CPUCLK_MAX 133000000
#define CFG_MEASURE_CPUCLK
#define CFG_8XX_XIN CONFIG_8xx_OSCLK
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"bootp;" \
"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
"bootm"
#undef CONFIG_WATCHDOG /* watchdog disabled */
#undef CONFIG_STATUS_LED /* Status LED disabled */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
#define FEC_ENET
#define CONFIG_MII
#define CFG_DISCOVER_PHY 1
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
#define CFG_I2C_SPEED 100000 /* 100 kHz */
#define CFG_I2C_SLAVE 0x7f
/*
* Software (bit-bang) I2C driver configuration
*/
#define SCL 0x1000 /* PA 3 */
#define SDA 0x2000 /* PA 2 */
#define PAR immr->im_ioport.iop_papar
#define DIR immr->im_ioport.iop_padir
#define DAT immr->im_ioport.iop_padat
#define I2C_INIT {PAR &= ~(SCL | SDA); DIR |= SCL;}
#define I2C_ACTIVE (DIR |= SDA)
#define I2C_TRISTATE (DIR &= ~SDA)
#define I2C_READ ((DAT & SDA) != 0)
#define I2C_SDA(bit) if (bit) DAT |= SDA; \
else DAT &= ~SDA
#define I2C_SCL(bit) if (bit) DAT |= SCL; \
else DAT &= ~SCL
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CONFIG_RTC_PCF8563
#define CFG_I2C_RTC_ADDR 0x51
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_I2C | \
CFG_CMD_NAND | \
CFG_CMD_JFFS2 | \
CFG_CMD_NFS | \
CFG_CMD_SNTP )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
#define CFG_LOAD_ADDR 0x00100000
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CFG_IMMR 0xF0000000
#define CFG_IMMR_SIZE ((uint)(64 * 1024))
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x40000000
#define CFG_RESET_ADDRESS 0xFFF00100
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_OFFSET 0x00740000
#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */
#define CFG_ENV_SIZE 0x4000 /* Used Size of Environment Sector */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*
* NAND flash support
*/
#define CFG_MAX_NAND_DEVICE 1
#define NAND_ChipID_UNKNOWN 0x00
#define SECTORSIZE 512
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define ADDR_COLUMN 1
#define NAND_NO_RB
#define NAND_WAIT_READY(nand) udelay(12)
#define WRITE_NAND_COMMAND(d, adr) WRITE_NAND(d, adr + 2)
#define WRITE_NAND_ADDRESS(d, adr) WRITE_NAND(d, adr + 1)
#define WRITE_NAND(d, adr) (*(volatile uint8_t *)(adr) = (uint8_t)(d))
#define READ_NAND(adr) (*(volatile uint8_t *)(adr))
#define NAND_DISABLE_CE(nand) /* nop */
#define NAND_ENABLE_CE(nand) /* nop */
#define NAND_CTL_CLRALE(nandptr) /* nop */
#define NAND_CTL_SETALE(nandptr) /* nop */
#define NAND_CTL_CLRCLE(nandptr) /* nop */
#define NAND_CTL_SETCLE(nandptr) /* nop */
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
*/
#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
#define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | \
SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
SCCR_DFLCD000 | SCCR_DFALCD00)
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
#define CFG_DER 0
/*
* Init Memory Controller:
*
* BR0 and OR0 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
/* FLASH timing: Default value of OR0 after reset */
#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
OR_SCY_15_CLK | OR_TRLX)
#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
/*
* BR2 and OR2 (NAND Flash) - now addressed through UPMB
*/
#define CFG_NAND_BASE 0x50000000
#define CFG_NAND_SIZE 0x04000000
#define CFG_OR_TIMING_NAND (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
OR_SCY_15_CLK | OR_EHTR | OR_TRLX)
#define CFG_BR2_PRELIM ((CFG_NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_MS_UPMB | BR_V )
#define CFG_OR2_PRELIM (((-CFG_NAND_SIZE) & OR_AM_MSK) | OR_BI )
/*
* BR3 and OR3 (SDRAM)
*/
#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
/*
* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)
*/
#define CFG_OR_TIMING_SDRAM 0x00000A00
#define CFG_OR3_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM)
#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
/*
* BR5 and OR5 (SRAM)
*/
#define CFG_SRAM_BASE 0x60000000
#define CFG_SRAM_SIZE 0x00080000
#define CFG_OR_TIMING_SRAM (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
OR_SCY_15_CLK | OR_EHTR | OR_TRLX)
#define CFG_BR5_PRELIM ((CFG_SRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
#define CFG_OR5_PRELIM (((-CFG_SRAM_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_SRAM)
/*
* 4096 Rows from SDRAM example configuration
* 1000 factor s -> ms
* 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
* 4 Number of refresh cycles per period
* 64 Refresh cycle in ms per number of rows
*/
#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
#define CFG_MAMR_PTA 39
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/*
* MBMR settings for NAND flash
*/
#define CFG_MBMR_NAND ( MBMR_WLFB_5X )
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
#define CONFIG_JFFS2_NAND_DEV 0 /* nand device jffs2 lives on */
#define CONFIG_JFFS2_NAND_OFF 0 /* start of jffs2 partition */
#define CONFIG_JFFS2_NAND_SIZE 4*1024*1024 /* size of jffs2 partition */
#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
#endif /* __CONFIG_H */