u-boot/include/configs/draco.h
Heiko Schocher 61159b7684 arm, am33xx: update for siemens am335x based boards
updates for the siemens am335x based boards:

- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
  to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
  Leds can now be defined in Environment
- add generic env based dfu button
  Which gpio is used for the dfu button can be defined
  through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Heiko Schocher <hs@denx.de>
2015-06-19 16:46:47 -04:00

111 lines
2.4 KiB
C

/*
* (C) Copyright 2013 Siemens Schweiz AG
* (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* U-Boot file:/include/configs/am335x_evm.h
*
* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_DRACO_H
#define __CONFIG_DRACO_H
#define CONFIG_SIEMENS_DRACO
#define MACH_TYPE_DRACO 4314
#define CONFIG_SIEMENS_MACH_TYPE MACH_TYPE_DRACO
#include "siemens-am33x-common.h"
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_SYS_MPUCLK 300
#define DDR_PLL_FREQ 303
#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#define BOARD_DFU_BUTTON_GPIO 27 /* Use as default */
#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */
#define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
"button_dfu0=27\0" \
"led0=103,1,0\0" \
"led1=64,0,1\0"
#undef CONFIG_DOS_PARTITION
#undef CONFIG_CMD_FAT
#define CONFIG_BOARD_LATE_INIT
/* Physical Memory Map */
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
/* I2C Configuration */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define EEPROM_ADDR_DDR3 0x90
#define EEPROM_ADDR_CHIP 0x120
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300
#undef CONFIG_SPL_NET_SUPPORT
#undef CONFIG_SPL_NET_VCI_STRING
#undef CONFIG_SPL_ETH_SUPPORT
#undef CONFIG_MII
#undef CONFIG_PHY_GIGE
#define CONFIG_PHY_SMSC
#define CONFIG_FACTORYSET
/* Watchdog */
#define CONFIG_OMAP_WATCHDOG
/* Define own nand partitions */
#define CONFIG_ENV_OFFSET_REDUND 0x2E0000
#define CONFIG_ENV_SIZE_REDUND 0x2000
#define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE)
#define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V2
#ifndef CONFIG_SPL_BUILD
/* Default env settings */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hostname=draco\0" \
"nand_img_size=0x400000\0" \
"optargs=\0" \
"preboot=draco_led 0\0" \
CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
CONFIG_ENV_SETTINGS_V2 \
CONFIG_ENV_SETTINGS_NAND_V2
#ifndef CONFIG_RESTORE_FLASH
/* set to negative value for no autoboot */
#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTCOMMAND \
"if dfubutton; then " \
"run dfu_start; " \
"reset; " \
"fi;" \
"run nand_boot;" \
"run nand_boot_backup;" \
"reset;"
#else
#define CONFIG_BOOTDELAY 0
#define CONFIG_BOOTCOMMAND \
"setenv autoload no; " \
"dhcp; " \
"if tftp 80000000 debrick.scr; then " \
"source 80000000; " \
"fi"
#endif
#endif /* CONFIG_SPL_BUILD */
#endif /* ! __CONFIG_DRACO_H */