u-boot/include/configs/grsim.h
Francois Retief 4c547754f5 sparc: Add CONFIG_DISPLAY_BOARDINFO variable to all LEON boards
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
2015-12-03 13:15:49 +02:00

326 lines
10 KiB
C

/* Configuration header file for LEON3 GRSIM, trying to be similar
* to Gaisler's GR-XC3S-1500 board.
*
* (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2007
* Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H__
#define __CONFIG_H__
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO
/*
* High Level Configuration Options
* (easy to change)
*
* Select between TSIM or GRSIM by setting CONFIG_GRSIM or CONFIG_TSIM to 1.
*
* TSIM command:
* $ tsim-leon3 -sdram 32768 -ram 4096 -rom 2048 -mmu -cas
*
* In the evaluation version of TSIM, the -sdram/-ram/-rom arguments are
* hard-coded to these values and need not be specified. (see below)
*
* Get TSIM from http://www.gaisler.com/index.php/downloads/simulators
*/
#define CONFIG_GRSIM 0 /* ... not running on GRSIM */
#define CONFIG_TSIM 1 /* ... running on TSIM */
/* CPU / AMBA BUS configuration */
#define CONFIG_SYS_CLK_FREQ 40000000 /* 40MHz */
/*
* Serial console configuration
*/
#define CONFIG_BAUDRATE 38400 /* ... at 38400 bps */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/* Partitions */
#define CONFIG_DOS_PARTITION
#define CONFIG_MAC_PARTITION
#define CONFIG_ISO_PARTITION
/*
* Supported commands
*/
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_REGINFO
/*
* Autobooting
*/
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
/*#define CONFIG_SYS_HUSH_PARSER 0*/
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0" \
"rootpath=/export/roofs\0" \
"scratch=40000000\0" \
"getkernel=tftpboot $(scratch) $(bootfile)\0" \
"bootargs=console=ttyS0,38400" \
""
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_SERVERIP 192.168.0.81
#define CONFIG_IPADDR 192.168.0.80
#define CONFIG_ROOTPATH "/export/rootfs"
#define CONFIG_HOSTNAME grxc3s1500
#define CONFIG_BOOTFILE "/uImage"
#define CONFIG_BOOTCOMMAND "run flash_self"
/* Memory MAP
*
* Flash:
* |--------------------------------|
* | 0x00000000 Text & Data & BSS | *
* | for Monitor | *
* | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
* | UNUSED / Growth | * 256kb
* |--------------------------------|
* | 0x00050000 Base custom area | *
* | kernel / FS | *
* | | * Rest of Flash
* |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
* | END-0x00008000 Environment | * 32kb
* |--------------------------------|
*
*
*
* Main Memory:
* |--------------------------------|
* | UNUSED / scratch area |
* | |
* | |
* | |
* | |
* |--------------------------------|
* | Monitor .Text / .DATA / .BSS | * 256kb
* | Relocated! | *
* |--------------------------------|
* | Monitor Malloc | * 128kb (contains relocated environment)
* |--------------------------------|
* | Monitor/kernel STACK | * 64kb
* |--------------------------------|
* | Page Table for MMU systems | * 2k
* |--------------------------------|
* | PROM Code accessed from Linux | * 6kb-128b
* |--------------------------------|
* | Global data (avail from kernel)| * 128b
* |--------------------------------|
*
*/
/*
* Flash configuration (8,16 or 32 MB)
* TEXT base always at 0xFFF00000
* ENV_ADDR always at 0xFFF40000
* FLASH_BASE at 0xFC000000 for 64 MB
* 0xFE000000 for 32 MB
* 0xFF000000 for 16 MB
* 0xFF800000 for 8 MB
*/
#define CONFIG_SYS_NO_FLASH 1
#define CONFIG_SYS_FLASH_BASE 0x00000000
#define CONFIG_SYS_FLASH_SIZE 0x00800000
#define CONFIG_ENV_SIZE 0x8000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SIZE)
#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors */
#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max num of sects on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
#ifdef ENABLE_FLASH_SUPPORT
/* For use with grsim FLASH emulation extension */
#define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
#undef CONFIG_FLASH_8BIT /* Flash is 32-bit */
/*** CFI CONFIG ***/
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#endif
/*
* Environment settings
*/
#define CONFIG_ENV_IS_NOWHERE 1
/*#define CONFIG_ENV_IS_IN_FLASH*/
/*#define CONFIG_ENV_SIZE 0x8000*/
#define CONFIG_ENV_SECT_SIZE 0x40000
#define CONFIG_ENV_OVERWRITE 1
/*
* Memory map
*/
#define CONFIG_SYS_SDRAM_BASE 0x60000000
#define CONFIG_SYS_SDRAM_SIZE 0x02000000 /* 32MiB SDRAM */
#define CONFIG_SYS_SDRAM_END (CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_SDRAM_SIZE)
#define CONFIG_SYS_SRAM_BASE 0x40000000
#define CONFIG_SYS_SRAM_SIZE 0x00400000 /* 4MiB SRAM */
#define CONFIG_SYS_SRAM_END (CONFIG_SYS_SRAM_BASE + CONFIG_SYS_SRAM_SIZE)
/* Always Run U-Boot from SDRAM */
#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_RAM_END - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_PROM_SIZE (8192-GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_PROM_OFFSET-32)
#define CONFIG_SYS_STACK_SIZE (0x10000-32)
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
# define CONFIG_SYS_RAMBOOT 1
#endif
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_MALLOC_END (CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
/* relocated monitor area */
#define CONFIG_SYS_RELOC_MONITOR_MAX_END CONFIG_SYS_MALLOC_BASE
#define CONFIG_SYS_RELOC_MONITOR_BASE (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
/* make un relocated address from relocated address */
#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
#ifdef CONFIG_CMD_NET
/*
* Ethernet configuration
*/
#define CONFIG_GRETH 1
/*
* Define CONFIG_GRETH_10MBIT to force GRETH at 10Mb/s
*/
/* #define CONFIG_GRETH_10MBIT 1 */
#define CONFIG_PHY_ADDR 0x00
#endif /* CONFIG_CMD_NET */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
/***** Gaisler GRLIB IP-Cores Config ********/
#define CONFIG_SYS_GRLIB_SDRAM 0
#define CONFIG_SYS_GRLIB_MEMCFG1 (0x000000ff | (1<<11))
/* No SDRAM Configuration */
#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
/* LEON2 MCTRL configuration */
#define CONFIG_SYS_GRLIB_ESA_MCTRL1
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1 (0x000000ff | (1<<11))
#if CONFIG_GRSIM
/* GRSIM configuration */
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x82206000
#else
/* TSIM configuration */
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x81805220
#endif
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3 0x00136000
/* GRLIB FT-MCTRL configuration */
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1 (0x000000ff | (1<<11))
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x82206000
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3 0x00136000
/* no DDR controller */
#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
/* no DDR2 Controller */
#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
/* default kernel command line */
#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
#define CONFIG_IDENT_STRING " Gaisler GRSIM"
/* TSIM command:
* $ ./tsim-leon3 -mmu -cas
*
* This TSIM evaluation version will expire 2015-04-02
*
*
* TSIM/LEON3 SPARC simulator, version 2.0.35 (evaluation version)
*
* Copyright (C) 2014, Aeroflex Gaisler - all rights reserved.
* This software may only be used with a valid license.
* For latest updates, go to http://www.gaisler.com/
* Comments or bug-reports to support@gaisler.com
*
* serial port A on stdin/stdout
* allocated 4096 K SRAM memory, in 1 bank
* allocated 32 M SDRAM memory, in 1 bank
* allocated 2048 K ROM memory
* icache: 1 * 4 kbytes, 16 bytes/line (4 kbytes total)
* dcache: 1 * 4 kbytes, 16 bytes/line (4 kbytes total)
* tsim> leon
* 0x80000000 Memory configuration register 1 0x000002ff
* 0x80000004 Memory configuration register 2 0x81805220
* 0x80000008 Memory configuration register 3 0x00000000
*/
#endif /* __CONFIG_H */