u-boot/board/icu862/icu862.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

200 lines
5.2 KiB
C

/*
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <config.h>
#include <mpc8xx.h>
/*
* Memory Controller Using
*
* CS0 - Flash memory (0x40000000)
* CS1 - SDRAM (0x00000000}
* CS2 - S/UNI Ultra ATM155
* CS3 - IDT 77106 ATM25
* CS4 - DSP HPI
* CS5 - E1/T1 Interface device
* CS6 - PCMCIA device
* CS7 - PCMCIA device
*/
/* ------------------------------------------------------------------------- */
#define _not_used_ 0xffffffff
const uint sdram_table[] = {
/* single read. (offset 0 in upm RAM) */
0x1f07fc04, 0xeeaefc04, 0x11adfc04, 0xefbbbc00,
0x1ff77c47,
/* MRS initialization (offset 5) */
0x1ff77c34, 0xefeabc34, 0x1fb57c35,
/* burst read. (offset 8 in upm RAM) */
0x1f07fc04, 0xeeaefc04, 0x10adfc04, 0xf0affc00,
0xf0affc00, 0xf1affc00, 0xefbbbc00, 0x1ff77c47,
_not_used_, _not_used_, _not_used_, _not_used_,
_not_used_, _not_used_, _not_used_, _not_used_,
/* single write. (offset 18 in upm RAM) */
0x1f27fc04, 0xeeaebc00, 0x01b93c04, 0x1ff77c47,
_not_used_, _not_used_, _not_used_, _not_used_,
/* burst write. (offset 20 in upm RAM) */
0x1f07fc04, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
0xf0affc00, 0xe1bbbc04, 0x1ff77c47, _not_used_,
_not_used_, _not_used_, _not_used_, _not_used_,
_not_used_, _not_used_, _not_used_, _not_used_,
/* refresh. (offset 30 in upm RAM) */
0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04,
0xfffffc84, 0xfffffc07, _not_used_, _not_used_,
_not_used_, _not_used_, _not_used_, _not_used_,
/* exception. (offset 3c in upm RAM) */
0x7ffffc07, _not_used_, _not_used_, _not_used_
};
/* ------------------------------------------------------------------------- */
/*
* Check Board Identity:
*/
int checkboard (void)
{
puts ("Board: ICU862 Board\n");
return 0;
}
/* ------------------------------------------------------------------------- */
static long int dram_size (long int, long int *, long int);
/* ------------------------------------------------------------------------- */
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size8, size9;
long int size_b0 = 0;
unsigned long reg;
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
/*
* Preliminary prescaler for refresh (depends on number of
* banks): This value is selected for four cycles every 62.4 us
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
memctl->memc_mar = 0x00000088;
/*
* Map controller bank 1 to the SDRAM bank at
* preliminary address - these have to be modified after the
* SDRAM size has been determined.
*/
memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
udelay (200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
udelay (200);
memctl->memc_mcr = 0x80002230; /* SDRAM bank 0 - execute twice */
udelay (200);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CONFIG_SYS_MAMR_8COL, SDRAM_BASE1_PRELIM,
SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CONFIG_SYS_MAMR_9COL, SDRAM_BASE1_PRELIM,
SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
udelay (500);
/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
}
udelay (1000);
/*
* Adjust refresh rate depending on SDRAM type, both banks
* For types > 128 MBit leave it at the current (fast) rate
*/
if ((size_b0 < 0x02000000)) {
/* reduce to 15.6 us (62.4 us / quad) */
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
udelay (1000);
}
/*
* Final mapping
*/
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
/* adjust refresh rate depending on SDRAM type, one bank */
reg = memctl->memc_mptpr;
reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
memctl->memc_mptpr = reg;
udelay (10000);
return (size_b0);
}
/* ------------------------------------------------------------------------- */
/*
* Check memory range for valid RAM. A simple memory test determines
* the actually available RAM size between addresses `base' and
* `base + maxsize'. Some (not all) hardware errors are detected:
* - short between address lines
* - short between data lines
*/
static long int dram_size (long int mamr_value, long int *base,
long int maxsize)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
memctl->memc_mamr = mamr_value;
return (get_ram_size(base, maxsize));
}