u-boot/include/configs/dra7xx_evm.h
Tom Rini 79b079f35c dra7xx_evm: Add QSPI_4 support, qspiboot build target
We previously only supported QSPI_1 (single) support.  Add QSPI_4 (quad)
read support as well.  This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value.  We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment.  When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:37 -04:00

147 lines
4.3 KiB
C

/*
* (C) Copyright 2013
* Texas Instruments Incorporated.
* Lokesh Vutla <lokeshvutla@ti.com>
*
* Configuration settings for the TI DRA7XX board.
* See ti_omap5_common.h for omap5 common settings.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_DRA7XX_EVM_H
#define __CONFIG_DRA7XX_EVM_H
#define CONFIG_DRA7XX
#ifndef CONFIG_QSPI_BOOT
/* MMC ENV related defines */
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
#define CONFIG_ENV_SIZE (128 << 10)
#define CONFIG_ENV_OFFSET 0xE0000
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#endif
#define CONFIG_CMD_SAVEENV
#if (CONFIG_CONS_INDEX == 1)
#define CONSOLEDEV "ttyO0"
#elif (CONFIG_CONS_INDEX == 3)
#define CONSOLEDEV "ttyO2"
#endif
#define CONFIG_SYS_NS16550_COM1 UART1_BASE /* Base EVM has UART0 */
#define CONFIG_SYS_NS16550_COM2 UART2_BASE /* UART2 */
#define CONFIG_SYS_NS16550_COM3 UART3_BASE /* UART3 */
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_OMAP_ABE_SYSCK
/* Define the default GPT table for eMMC */
#define PARTS_DEFAULT \
"uuid_disk=${uuid_gpt_disk};" \
"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
#include <configs/ti_omap5_common.h>
/* Enhance our eMMC support / experience. */
#define CONFIG_CMD_GPT
#define CONFIG_EFI_PARTITION
#define CONFIG_PARTITION_UUIDS
#define CONFIG_CMD_PART
/* CPSW Ethernet */
#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */
#define CONFIG_CMD_DHCP
#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_NET_RETRY_COUNT 10
#define CONFIG_CMD_PING
#define CONFIG_CMD_MII
#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */
#define CONFIG_MII /* Required in net/eth.c */
#define CONFIG_PHY_GIGE /* per-board part of CPSW */
#define CONFIG_PHYLIB
/* SPI */
#undef CONFIG_OMAP3_SPI
#define CONFIG_TI_QSPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_TI_SPI_MMAP
#define CONFIG_SF_DEFAULT_SPEED 48000000
#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_3
/*
* Default to using SPI for environment, etc.
* 0x000000 - 0x010000 : QSPI.SPL (64KiB)
* 0x010000 - 0x020000 : QSPI.SPL.backup1 (64KiB)
* 0x020000 - 0x030000 : QSPI.SPL.backup2 (64KiB)
* 0x030000 - 0x040000 : QSPI.SPL.backup3 (64KiB)
* 0x040000 - 0x140000 : QSPI.u-boot (1MiB)
* 0x140000 - 0x1C0000 : QSPI.u-boot-spl-os (512KiB)
* 0x1C0000 - 0x1D0000 : QSPI.u-boot-env (64KiB)
* 0x1D0000 - 0x1E0000 : QSPI.u-boot-env.backup1 (64KiB)
* 0x1E0000 - 0x9E0000 : QSPI.kernel (8MiB)
* 0x9E0000 - 0x2000000 : USERLAND
*/
#define CONFIG_SYS_SPI_KERNEL_OFFS 0x1E0000
#define CONFIG_SYS_SPI_ARGS_OFFS 0x140000
#define CONFIG_SYS_SPI_ARGS_SIZE 0x80000
#if defined(CONFIG_QSPI_BOOT)
/* In SPL, use the environment and discard MMC support for space. */
#ifdef CONFIG_SPL_BUILD
#undef CONFIG_SPL_MMC_SUPPORT
#undef CONFIG_SPL_MAX_SIZE
#define CONFIG_SPL_MAX_SIZE (64 << 10) /* 64 KiB */
#endif
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#define CONFIG_ENV_SIZE (64 << 10)
#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64 KB sectors */
#define CONFIG_ENV_OFFSET 0x1C0000
#define CONFIG_ENV_OFFSET_REDUND 0x1D0000
#endif
/* SPI SPL */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_BUS 0
#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000
#define CONFIG_SUPPORT_EMMC_BOOT
/* USB xHCI HOST */
#define CONFIG_CMD_USB
#define CONFIG_USB_HOST
#define CONFIG_USB_XHCI
#define CONFIG_USB_XHCI_OMAP
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#define CONFIG_OMAP_USB_PHY
#define CONFIG_OMAP_USB2PHY2_HOST
/* SATA */
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_CMD_SCSI
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#endif /* __CONFIG_DRA7XX_EVM_H */