u-boot/drivers/Makefile
Simon Glass 76f1f38816 Use separate options for TPL support
At present TPL uses the same options as SPL support. In a few cases the board
config enables or disables the SPL options depending on whether
CONFIG_TPL_BUILD is defined.

With the move to Kconfig, options are determined for the whole build and
(without a hack like an #undef in a header file) cannot be controlled in this
way.

Create new TPL options for these and update users. This will allow Kconfig
conversion to proceed for these boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:03:39 -04:00

96 lines
2.7 KiB
Makefile

#
# SPDX-License-Identifier: GPL-2.0+
#
obj-$(CONFIG_$(SPL_)DM) += core/
obj-$(CONFIG_$(SPL_)CLK) += clk/
obj-$(CONFIG_$(SPL_)LED) += led/
obj-$(CONFIG_$(SPL_)PINCTRL) += pinctrl/
obj-$(CONFIG_$(SPL_)RAM) += ram/
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/
obj-$(CONFIG_SPL_I2C_SUPPORT) += i2c/
obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/
obj-$(CONFIG_SPL_MMC_SUPPORT) += mmc/
obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/
obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/
obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/
obj-$(CONFIG_SPL_SERIAL_SUPPORT) += serial/
obj-$(CONFIG_SPL_SPI_SUPPORT) += spi/
obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/
obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/
obj-$(CONFIG_SPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/
obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/
obj-$(CONFIG_SPL_NAND_SUPPORT) += mtd/nand/
obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/
obj-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += mtd/spi/
obj-$(CONFIG_SPL_UBI) += mtd/ubispl/
obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/
obj-$(CONFIG_SPL_ETH_SUPPORT) += net/
obj-$(CONFIG_SPL_ETH_SUPPORT) += net/phy/
obj-$(CONFIG_SPL_USBETH_SUPPORT) += net/phy/
obj-$(CONFIG_SPL_MUSB_NEW_SUPPORT) += usb/musb-new/
obj-$(CONFIG_SPL_USBETH_SUPPORT) += usb/gadget/
obj-$(CONFIG_SPL_WATCHDOG_SUPPORT) += watchdog/
obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += usb/host/
obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/
obj-$(CONFIG_SPL_SATA_SUPPORT) += block/
obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/
obj-$(CONFIG_SPL_MMC_SUPPORT) += block/
endif
ifdef CONFIG_TPL_BUILD
obj-$(CONFIG_TPL_I2C_SUPPORT) += i2c/
obj-$(CONFIG_TPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/
obj-$(CONFIG_TPL_MMC_SUPPORT) += mmc/
obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
obj-$(CONFIG_TPL_NAND_SUPPORT) += mtd/nand/
obj-$(CONFIG_TPL_SERIAL_SUPPORT) += serial/
obj-$(CONFIG_TPL_SPI_FLASH_SUPPORT) += mtd/spi/
obj-$(CONFIG_TPL_SPI_SUPPORT) += spi/
endif
ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TPL_BUILD),)
obj-y += adc/
obj-$(CONFIG_DM_DEMO) += demo/
obj-$(CONFIG_BIOSEMU) += bios_emulator/
obj-y += block/
obj-$(CONFIG_BOOTCOUNT_LIMIT) += bootcount/
obj-$(CONFIG_CPU) += cpu/
obj-y += crypto/
obj-$(CONFIG_FPGA) += fpga/
obj-y += hwmon/
obj-y += misc/
obj-y += pcmcia/
obj-y += dfu/
obj-$(CONFIG_X86) += pch/
obj-y += rtc/
obj-y += sound/
obj-y += spmi/
obj-y += sysreset/
obj-y += timer/
obj-y += tpm/
obj-y += twserial/
obj-y += video/
obj-y += watchdog/
obj-$(CONFIG_QE) += qe/
obj-$(CONFIG_U_QE) += qe/
obj-y += mailbox/
obj-y += memory/
obj-y += pwm/
obj-y += reset/
obj-y += input/
# SOC specific infrastructure drivers.
obj-y += soc/
obj-$(CONFIG_REMOTEPROC) += remoteproc/
obj-y += thermal/
obj-$(CONFIG_MACH_PIC32) += ddr/microchip/
endif