u-boot/include/configs/Sandpoint8240.h
Masahiro Yamada 52de0e49df powerpc: mpc824x: remove redundant CONFIG_MPC824X definition
We do not have to define CONFIG_MPC824X in board config headers
because it is defined in arch/powerpc/cpu/mpc824x/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:08 -05:00

399 lines
13 KiB
C

/*
* (C) Copyright 2001-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/* ------------------------------------------------------------------------- */
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC8240 1
#define CONFIG_SANDPOINT 1
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
#define CONFIG_SYS_LDSCRIPT "board/sandpoint/u-boot.lds"
#if 0
#define USE_DINK32 1
#else
#undef USE_DINK32
#endif
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run net_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"net_self=tftp ${kernel_addr} ${bootfile};" \
"tftp ${ramdisk_addr} ${ramdisk};" \
"run ramargs addip;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp ${kernel_addr} ${bootfile};" \
"run nfsargs addip;bootm\0" \
"rootpath=/opt/eldk/ppc_82xx\0" \
"bootfile=/tftpboot/SP8240/uImage\0" \
"ramdisk=/tftpboot/SP8240/uRamdisk\0" \
"kernel_addr=200000\0" \
"ramdisk_addr=400000\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SNTP
#define CONFIG_DRAM_SPEED 100 /* MHz */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#undef CONFIG_PCI_PNP
#define CONFIG_EEPRO100
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define PCI_ENET0_IOADDR 0x80000000
#define PCI_ENET0_MEMADDR 0x80000000
#define PCI_ENET1_IOADDR 0x81000000
#define PCI_ENET1_MEMADDR 0x81000000
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000
#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
#if defined (USE_DINK32)
#define CONFIG_SYS_MONITOR_LEN 0x00030000
#define CONFIG_SYS_MONITOR_BASE 0x00090000
#define CONFIG_SYS_RAMBOOT 1
#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#else
#undef CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_MONITOR_LEN 0x00030000
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#endif
#define CONFIG_SYS_FLASH_BASE 0xFFF00000
#if 0
#define CONFIG_SYS_FLASH_SIZE (512 * 1024) /* sandpoint has tiny eeprom */
#else
#define CONFIG_SYS_FLASH_SIZE (1024 * 1024) /* Unity has onboard 1MByte flash */
#endif
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */
#define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */
#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */
#define CONFIG_SYS_EUMB_ADDR 0xFC000000
#define CONFIG_SYS_ISA_MEM 0xFD000000
#define CONFIG_SYS_ISA_IO 0xFE000000
#define CONFIG_SYS_FLASH_RANGE_BASE 0xFF000000 /* flash memory address range */
#define CONFIG_SYS_FLASH_RANGE_SIZE 0x01000000
#define FLASH_BASE0_PRELIM 0xFFF00000 /* sandpoint flash */
#define FLASH_BASE1_PRELIM 0xFF000000 /* PMC onboard flash */
/*
* select i2c support configuration
*
* Supported configurations are {none, software, hardware} drivers.
* If the software driver is chosen, there are some additional
* configuration items that the driver uses to drive the port pins.
*/
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
#undef CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_SPEED 400000
#ifdef CONFIG_SYS_I2C_SOFT
#error "Soft I2C is not configured properly. Please review!"
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
#define I2C_ACTIVE (iop->pdir |= 0x00010000)
#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
#define I2C_READ ((iop->pdat & 0x00010000) != 0)
#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
else iop->pdat &= ~0x00010000
#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
else iop->pdat &= ~0x00020000
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#endif /* CONFIG_SYS_I2C_SOFT */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* write page size */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
#define CONFIG_SYS_FLASH_BANKS { FLASH_BASE0_PRELIM , FLASH_BASE1_PRELIM }
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
/* #define CONFIG_WINBOND_83C553 1 / *has a winbond bridge */
#define CONFIG_SYS_USE_WINBOND_IDE 0 /*use winbond 83c553 internal IDE ctrlr */
#define CONFIG_SYS_WINBOND_ISA_CFG_ADDR 0x80005800 /*pci-isa bridge config addr */
#define CONFIG_SYS_WINBOND_IDE_CFG_ADDR 0x80005900 /*ide config addr */
#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
/*
* NS87308 Configuration
*/
#define CONFIG_NS87308 /* Nat Semi super-io controller on ISA bus */
#define CONFIG_SYS_NS87308_BADDR_10 1
#define CONFIG_SYS_NS87308_DEVS ( CONFIG_SYS_NS87308_UART1 | \
CONFIG_SYS_NS87308_UART2 | \
CONFIG_SYS_NS87308_POWRMAN | \
CONFIG_SYS_NS87308_RTC_APC )
#undef CONFIG_SYS_NS87308_PS2MOD
#define CONFIG_SYS_NS87308_CS0_BASE 0x0076
#define CONFIG_SYS_NS87308_CS0_CONF 0x30
#define CONFIG_SYS_NS87308_CS1_BASE 0x0075
#define CONFIG_SYS_NS87308_CS1_CONF 0x30
#define CONFIG_SYS_NS87308_CS2_BASE 0x0074
#define CONFIG_SYS_NS87308_CS2_CONF 0x30
/*
* NS16550 Configuration
*/
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK 1843200
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART1_BASE)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART2_BASE)
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 1
#define CONFIG_SYS_ROMNAL 7 /*rom/flash next access time */
#define CONFIG_SYS_ROMFAL 11 /*rom/flash access time */
#define CONFIG_SYS_REFINT 430 /* no of clock cycles between CBR refresh cycles */
/* the following are for SDRAM only*/
#define CONFIG_SYS_BSTOPRE 121 /* Burst To Precharge, sets open page interval */
#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */
#define CONFIG_SYS_RDLAT 4 /* data latency from read command */
#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */
#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */
#define CONFIG_SYS_ACTORW 3 /* Activate to R/W */
#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */
#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
/* memory bank settings*/
/*
* only bits 20-29 are actually used from these vales to set the
* start/end address the upper two bits will be 0, and the lower 20
* bits will be set to 0x00000 for a start address, or 0xfffff for an
* end address
*/
#define CONFIG_SYS_BANK0_START 0x00000000
#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
#define CONFIG_SYS_BANK0_ENABLE 1
#define CONFIG_SYS_BANK1_START 0x3ff00000
#define CONFIG_SYS_BANK1_END 0x3fffffff
#define CONFIG_SYS_BANK1_ENABLE 0
#define CONFIG_SYS_BANK2_START 0x3ff00000
#define CONFIG_SYS_BANK2_END 0x3fffffff
#define CONFIG_SYS_BANK2_ENABLE 0
#define CONFIG_SYS_BANK3_START 0x3ff00000
#define CONFIG_SYS_BANK3_END 0x3fffffff
#define CONFIG_SYS_BANK3_ENABLE 0
#define CONFIG_SYS_BANK4_START 0x00000000
#define CONFIG_SYS_BANK4_END 0x00000000
#define CONFIG_SYS_BANK4_ENABLE 0
#define CONFIG_SYS_BANK5_START 0x00000000
#define CONFIG_SYS_BANK5_END 0x00000000
#define CONFIG_SYS_BANK5_ENABLE 0
#define CONFIG_SYS_BANK6_START 0x00000000
#define CONFIG_SYS_BANK6_END 0x00000000
#define CONFIG_SYS_BANK6_ENABLE 0
#define CONFIG_SYS_BANK7_START 0x00000000
#define CONFIG_SYS_BANK7_END 0x00000000
#define CONFIG_SYS_BANK7_ENABLE 0
/*
* Memory bank enable bitmask, specifying which of the banks defined above
are actually present. MSB is for bank #7, LSB is for bank #0.
*/
#define CONFIG_SYS_BANK_ENABLE 0x01
#define CONFIG_SYS_ODCR 0xff /* configures line driver impedances, */
/* see 8240 book for bit definitions */
#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */
/* currently accessed page in memory */
/* see 8240 book for details */
/* SDRAM 0 - 256MB */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
/* stack in DCACHE @ 1GB (no backing mem) */
#if defined(USE_DINK32)
#define CONFIG_SYS_IBAT1L (0x40000000 | BATL_PP_00 )
#define CONFIG_SYS_IBAT1U (0x40000000 | BATU_BL_128K )
#else
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#endif
/* PCI memory */
#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
/* Flash, config addrs, etc */
#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 20 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8240 CPU */
#if defined(CONFIG_CMD_KGDB)
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/* values according to the manual */
#define CONFIG_DRAM_50MHZ 1
#define CONFIG_SDRAM_50MHZ
#undef NR_8259_INTS
#define NR_8259_INTS 1
#define CONFIG_DISK_SPINUP_TIME 1000000
#endif /* __CONFIG_H */