u-boot/scripts/Makefile.spl
Simon Glass 76f1f38816 Use separate options for TPL support
At present TPL uses the same options as SPL support. In a few cases the board
config enables or disables the SPL options depending on whether
CONFIG_TPL_BUILD is defined.

With the move to Kconfig, options are determined for the whole build and
(without a hack like an #undef in a header file) cannot be controlled in this
way.

Create new TPL options for these and update users. This will allow Kconfig
conversion to proceed for these boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:03:39 -04:00

325 lines
9.4 KiB
Makefile

#
# (C) Copyright 2000-2011
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# (C) Copyright 2011
# Daniel Schwierzeck, daniel.schwierzeck@googlemail.com.
#
# (C) Copyright 2011
# Texas Instruments Incorporated - http://www.ti.com/
# Aneesh V <aneesh@ti.com>
#
# SPDX-License-Identifier: GPL-2.0+
#
# Based on top-level Makefile.
#
src := $(obj)
# Create output directory if not already present
_dummy := $(shell [ -d $(obj) ] || mkdir -p $(obj))
include $(srctree)/scripts/Kbuild.include
-include include/config/auto.conf
-include $(obj)/include/autoconf.mk
KBUILD_CPPFLAGS += -DCONFIG_SPL_BUILD
ifeq ($(CONFIG_TPL_BUILD),y)
KBUILD_CPPFLAGS += -DCONFIG_TPL_BUILD
endif
ifeq ($(CONFIG_TPL_BUILD),y)
SPL_BIN := u-boot-tpl
else
SPL_BIN := u-boot-spl
endif
include $(srctree)/config.mk
include $(srctree)/arch/$(ARCH)/Makefile
# Enable garbage collection of un-used sections for SPL
KBUILD_CFLAGS += -ffunction-sections -fdata-sections
LDFLAGS_FINAL += --gc-sections
# FIX ME
cpp_flags := $(KBUILD_CPPFLAGS) $(PLATFORM_CPPFLAGS) $(UBOOTINCLUDE) \
$(NOSTDINC_FLAGS)
c_flags := $(KBUILD_CFLAGS) $(cpp_flags)
HAVE_VENDOR_COMMON_LIB = $(if $(wildcard $(srctree)/board/$(VENDOR)/common/Makefile),y,n)
libs-y += $(if $(BOARDDIR),board/$(BOARDDIR)/)
libs-$(HAVE_VENDOR_COMMON_LIB) += board/$(VENDOR)/common/
libs-$(CONFIG_SPL_FRAMEWORK) += common/spl/
libs-y += common/init/
# Special handling for a few options which support SPL/TPL
ifeq ($(CONFIG_TPL_BUILD),y)
libs-$(CONFIG_TPL_LIBCOMMON_SUPPORT) += common/ cmd/
libs-$(CONFIG_TPL_LIBGENERIC_SUPPORT) += lib/
else
libs-$(CONFIG_SPL_LIBCOMMON_SUPPORT) += common/ cmd/
libs-$(CONFIG_SPL_LIBGENERIC_SUPPORT) += lib/
endif
libs-$(CONFIG_SPL_LIBDISK_SUPPORT) += disk/
libs-y += drivers/
libs-y += dts/
libs-y += fs/
libs-$(CONFIG_SPL_POST_MEM_SUPPORT) += post/drivers/
libs-$(CONFIG_SPL_NET_SUPPORT) += net/
head-y := $(addprefix $(obj)/,$(head-y))
libs-y := $(addprefix $(obj)/,$(libs-y))
u-boot-spl-dirs := $(patsubst %/,%,$(filter %/, $(libs-y)))
libs-y := $(patsubst %/, %/built-in.o, $(libs-y))
# Add GCC lib
ifeq ($(CONFIG_USE_PRIVATE_LIBGCC),y)
PLATFORM_LIBGCC = arch/$(ARCH)/lib/lib.a
PLATFORM_LIBS := $(filter-out %/lib.a, $(filter-out -lgcc, $(PLATFORM_LIBS))) $(PLATFORM_LIBGCC)
endif
u-boot-spl-init := $(head-y)
u-boot-spl-main := $(libs-y)
ifdef CONFIG_SPL_OF_PLATDATA
u-boot-spl-platdata := $(obj)/dts/dt-platdata.o
endif
# Linker Script
ifdef CONFIG_SPL_LDSCRIPT
# need to strip off double quotes
LDSCRIPT := $(addprefix $(srctree)/,$(CONFIG_SPL_LDSCRIPT:"%"=%))
endif
ifeq ($(wildcard $(LDSCRIPT)),)
LDSCRIPT := $(srctree)/board/$(BOARDDIR)/u-boot-spl.lds
endif
ifeq ($(wildcard $(LDSCRIPT)),)
LDSCRIPT := $(srctree)/$(CPUDIR)/u-boot-spl.lds
endif
ifeq ($(wildcard $(LDSCRIPT)),)
LDSCRIPT := $(srctree)/arch/$(ARCH)/cpu/u-boot-spl.lds
endif
ifeq ($(wildcard $(LDSCRIPT)),)
$(error could not find linker script)
endif
# Special flags for CPP when processing the linker script.
# Pass the version down so we can handle backwards compatibility
# on the fly.
LDPPFLAGS += \
-include $(srctree)/include/u-boot/u-boot.lds.h \
-include $(objtree)/include/config.h \
-DCPUDIR=$(CPUDIR) \
$(shell $(LD) --version | \
sed -ne 's/GNU ld version \([0-9][0-9]*\)\.\([0-9][0-9]*\).*/-DLD_MAJOR=\1 -DLD_MINOR=\2/p')
quiet_cmd_mkimage = MKIMAGE $@
cmd_mkimage = $(objtree)/tools/mkimage $(MKIMAGEFLAGS_$(@F)) -d $< $@ \
$(if $(KBUILD_VERBOSE:1=), >/dev/null)
MKIMAGEFLAGS_MLO = -T omapimage -a $(CONFIG_SPL_TEXT_BASE)
MKIMAGEFLAGS_MLO.byteswap = -T omapimage -n byteswap -a $(CONFIG_SPL_TEXT_BASE)
MLO MLO.byteswap: $(obj)/u-boot-spl.bin FORCE
$(call if_changed,mkimage)
ifeq ($(CONFIG_SYS_SOC),"at91")
MKIMAGEFLAGS_boot.bin = -T atmelimage
ifeq ($(CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER),y)
MKIMAGEFLAGS_boot.bin += -n $(shell $(obj)/../tools/atmel_pmecc_params)
boot.bin: $(obj)/../tools/atmel_pmecc_params
endif
boot.bin: $(obj)/u-boot-spl.bin FORCE
$(call if_changed,mkimage)
else
ifdef CONFIG_ARCH_ZYNQ
MKIMAGEFLAGS_boot.bin = -T zynqimage
endif
ifdef CONFIG_ARCH_ZYNQMP
MKIMAGEFLAGS_boot.bin = -T zynqmpimage
endif
spl/boot.bin: $(obj)/u-boot-spl.bin FORCE
$(call if_changed,mkimage)
endif
ALL-y += $(obj)/$(SPL_BIN).bin $(obj)/$(SPL_BIN).cfg
ifdef CONFIG_SAMSUNG
ALL-y += $(obj)/$(BOARD)-spl.bin
endif
ifdef CONFIG_ARCH_SOCFPGA
ALL-y += $(obj)/$(SPL_BIN).sfp
endif
ifdef CONFIG_SUNXI
ALL-y += $(obj)/sunxi-spl.bin
endif
ifeq ($(CONFIG_SYS_SOC),"at91")
ALL-y += boot.bin
endif
ALL-$(CONFIG_ARCH_ZYNQ) += $(obj)/boot.bin
ALL-$(CONFIG_ARCH_ZYNQMP) += $(obj)/boot.bin
all: $(ALL-y)
quiet_cmd_cat = CAT $@
cmd_cat = cat $(filter-out $(PHONY), $^) > $@
quiet_cmd_copy = COPY $@
cmd_copy = cp $< $@
ifeq ($(CONFIG_SPL_OF_CONTROL)$(CONFIG_OF_SEPARATE)$(CONFIG_SPL_OF_PLATDATA),yy)
$(obj)/$(SPL_BIN)-dtb.bin: $(obj)/$(SPL_BIN)-nodtb.bin $(obj)/$(SPL_BIN)-pad.bin \
$(obj)/$(SPL_BIN).dtb FORCE
$(call if_changed,cat)
$(obj)/$(SPL_BIN).bin: $(obj)/$(SPL_BIN)-dtb.bin FORCE
$(call if_changed,copy)
else
$(obj)/$(SPL_BIN).bin: $(obj)/$(SPL_BIN)-nodtb.bin FORCE
$(call if_changed,copy)
endif
# Create a file that pads from the end of u-boot-spl-nodtb.bin to bss_end
$(obj)/$(SPL_BIN)-pad.bin: $(obj)/$(SPL_BIN)
@bss_size_str=$(shell $(NM) $< | awk 'BEGIN {size = 0} /__bss_size/ {size = $$1} END {print "ibase=16; " toupper(size)}' | bc); \
dd if=/dev/zero of=$@ bs=1 count=$${bss_size_str} 2>/dev/null;
# Pass the original device tree file through fdtgrep twice. The first pass
# removes any unwanted nodes (i.e. those which don't have the
# 'u-boot,dm-pre-reloc' property and thus are not needed by SPL. The second
# pass removes various unused properties from the remaining nodes.
# The output is typically a much smaller device tree file.
quiet_cmd_fdtgrep = FDTGREP $@
cmd_fdtgrep = $(objtree)/tools/fdtgrep -b u-boot,dm-pre-reloc -RT $< \
-n /chosen -O dtb | \
$(objtree)/tools/fdtgrep -r -O dtb - -o $@ \
$(addprefix -P ,$(subst $\",,$(CONFIG_OF_SPL_REMOVE_PROPS)))
$(obj)/$(SPL_BIN).dtb: dts/dt.dtb $(objtree)/tools/fdtgrep FORCE
$(call if_changed,fdtgrep)
quiet_cmd_cpp_cfg = CFG $@
cmd_cpp_cfg = $(CPP) -Wp,-MD,$(depfile) $(cpp_flags) $(LDPPFLAGS) -ansi \
-DDO_DEPS_ONLY -D__ASSEMBLY__ -x assembler-with-cpp -P -dM -E -o $@ $<
$(obj)/$(SPL_BIN).cfg: include/config.h FORCE
$(call if_changed,cpp_cfg)
pythonpath = PYTHONPATH=tools
quiet_cmd_dtocc = DTOC C $@
cmd_dtocc = $(pythonpath) $(srctree)/tools/dtoc/dtoc -d $(obj)/$(SPL_BIN).dtb -o $@ platdata
quiet_cmd_dtoch = DTOC H $@
cmd_dtoch = $(pythonpath) $(srctree)/tools/dtoc/dtoc -d $(obj)/$(SPL_BIN).dtb -o $@ struct
quiet_cmd_plat = PLAT $@
cmd_plat = $(CC) $(c_flags) -c $< -o $@
$(obj)/dts/dt-platdata.o: $(obj)/dts/dt-platdata.c include/generated/dt-structs.h
$(call if_changed,plat)
PHONY += dts_dir
dts_dir:
$(shell [ -d $(obj)/dts ] || mkdir -p $(obj)/dts)
include/generated/dt-structs.h: $(obj)/$(SPL_BIN).dtb dts_dir dtoc
$(call if_changed,dtoch)
$(obj)/dts/dt-platdata.c: $(obj)/$(SPL_BIN).dtb dts_dir dtoc
$(call if_changed,dtocc)
dtoc: #$(objtree)/tools/_libfdt.so
ifdef CONFIG_SAMSUNG
ifdef CONFIG_VAR_SIZE_SPL
VAR_SIZE_PARAM = --vs
else
VAR_SIZE_PARAM =
endif
$(obj)/$(BOARD)-spl.bin: $(obj)/u-boot-spl.bin
$(if $(wildcard $(objtree)/spl/board/samsung/$(BOARD)/tools/mk$(BOARD)spl),\
$(objtree)/spl/board/samsung/$(BOARD)/tools/mk$(BOARD)spl,\
$(objtree)/tools/mkexynosspl) $(VAR_SIZE_PARAM) $< $@
endif
quiet_cmd_objcopy = OBJCOPY $@
cmd_objcopy = $(OBJCOPY) $(OBJCOPYFLAGS) $(OBJCOPYFLAGS_$(@F)) $< $@
OBJCOPYFLAGS_$(SPL_BIN)-nodtb.bin = $(SPL_OBJCFLAGS) -O binary
$(obj)/$(SPL_BIN)-nodtb.bin: $(obj)/$(SPL_BIN) FORCE
$(call if_changed,objcopy)
LDFLAGS_$(SPL_BIN) += -T u-boot-spl.lds $(LDFLAGS_FINAL)
ifneq ($(CONFIG_SPL_TEXT_BASE),)
LDFLAGS_$(SPL_BIN) += -Ttext $(CONFIG_SPL_TEXT_BASE)
endif
MKIMAGEFLAGS_$(SPL_BIN).sfp = -T socfpgaimage
$(obj)/$(SPL_BIN).sfp: $(obj)/$(SPL_BIN).bin FORCE
$(call if_changed,mkimage)
quiet_cmd_mksunxiboot = MKSUNXI $@
cmd_mksunxiboot = $(objtree)/tools/mksunxiboot $< $@
$(obj)/sunxi-spl.bin: $(obj)/$(SPL_BIN).bin FORCE
$(call if_changed,mksunxiboot)
# Rule to link u-boot-spl
# May be overridden by arch/$(ARCH)/config.mk
quiet_cmd_u-boot-spl ?= LD $@
cmd_u-boot-spl ?= (cd $(obj) && $(LD) $(LDFLAGS) $(LDFLAGS_$(@F)) \
$(patsubst $(obj)/%,%,$(u-boot-spl-init)) --start-group \
$(patsubst $(obj)/%,%,$(u-boot-spl-main)) \
$(patsubst $(obj)/%,%,$(u-boot-spl-platdata)) \
--end-group \
$(PLATFORM_LIBS) -Map $(SPL_BIN).map -o $(SPL_BIN))
$(obj)/$(SPL_BIN): $(u-boot-spl-platdata) $(u-boot-spl-init) \
$(u-boot-spl-main) $(obj)/u-boot-spl.lds FORCE
$(call if_changed,u-boot-spl)
$(sort $(u-boot-spl-init) $(u-boot-spl-main)): $(u-boot-spl-dirs) ;
PHONY += $(u-boot-spl-dirs)
$(u-boot-spl-dirs): $(u-boot-spl-platdata)
$(Q)$(MAKE) $(build)=$@
quiet_cmd_cpp_lds = LDS $@
cmd_cpp_lds = $(CPP) -Wp,-MD,$(depfile) $(cpp_flags) $(LDPPFLAGS) -ansi \
-D__ASSEMBLY__ -x assembler-with-cpp -P -o $@ $<
$(obj)/u-boot-spl.lds: $(LDSCRIPT) FORCE
$(call if_changed_dep,cpp_lds)
# read all saved command lines
targets := $(wildcard $(sort $(targets)))
cmd_files := $(wildcard $(obj)/.*.cmd $(foreach f,$(targets),$(dir $(f)).$(notdir $(f)).cmd))
ifneq ($(cmd_files),)
$(cmd_files): ; # Do not try to update included dependency files
include $(cmd_files)
endif
PHONY += FORCE
FORCE:
# Declare the contents of the .PHONY variable as phony. We keep that
# information in a variable so we can use it in if_changed and friends.
.PHONY: $(PHONY)