u-boot/board/phytec/pcm030/pcm030.c
Peter Tyser 61f2b38a17 Replace "#include <asm-$ARCH/$FILE>" with "#include <asm/$FILE>"
The appropriate include/asm-$ARCH directory should already by symlinked
to include/asm so using the whole "asm-$ARCH" path is unnecessary.

This change should also allow us to move the include/asm-$ARCH
directories into their appropriate lib/$ARCH/ directories.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:04 +02:00

220 lines
5.6 KiB
C

/*
* (C) Copyright 2003
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004
* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
*
* (C) Copyright 2006
* Eric Schumann, Phytec Messtechnik GmbH
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <mpc5xxx.h>
#include <pci.h>
#include <asm/io.h>
#include "mt46v32m16-75.h"
#ifndef CONFIG_SYS_RAMBOOT
static void sdram_start(int hi_addr)
{
volatile struct mpc5xxx_cdm *cdm =
(struct mpc5xxx_cdm *)MPC5XXX_CDM;
volatile struct mpc5xxx_sdram *sdram =
(struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
/* unlock mode register */
out_be32 (&sdram->ctrl,
(SDRAM_CONTROL | 0x80000000 | hi_addr_bit));
/* precharge all banks */
out_be32 (&sdram->ctrl,
(SDRAM_CONTROL | 0x80000002 | hi_addr_bit));
#ifdef SDRAM_DDR
/* set mode register: extended mode */
out_be32 (&sdram->mode, (SDRAM_EMODE));
/* set mode register: reset DLL */
out_be32 (&sdram->mode,
(SDRAM_MODE | 0x04000000));
#endif
/* precharge all banks */
out_be32 (&sdram->ctrl,
(SDRAM_CONTROL | 0x80000002 | hi_addr_bit));
/* auto refresh */
out_be32 (&sdram->ctrl,
(SDRAM_CONTROL | 0x80000004 | hi_addr_bit));
/* set mode register */
out_be32 (&sdram->mode, (SDRAM_MODE));
/* normal operation */
out_be32 (&sdram->ctrl,
(SDRAM_CONTROL | hi_addr_bit));
/* set CDM clock enable register, set MPC5200B SDRAM bus */
/* to reduced driver strength */
out_be32 (&cdm->clock_enable, (0x00CFFFFF));
}
#endif
/*
* ATTENTION: Although partially referenced initdram does NOT make
* real use of CONFIG_SYS_SDRAM_BASE. The code does not
* work if CONFIG_SYS_SDRAM_BASE
* is something else than 0x00000000.
*/
phys_size_t initdram(int board_type)
{
volatile struct mpc5xxx_mmap_ctl *mm =
(struct mpc5xxx_mmap_ctl *)CONFIG_SYS_MBAR;
volatile struct mpc5xxx_cdm *cdm =
(struct mpc5xxx_cdm *)MPC5XXX_CDM;
volatile struct mpc5xxx_sdram *sdram =
(struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
ulong dramsize = 0;
ulong dramsize2 = 0;
#ifndef CONFIG_SYS_RAMBOOT
ulong test1, test2;
/* setup SDRAM chip selects */
/* 256MB at 0x0 */
out_be32 (&mm->sdram0, 0x0000001b);
/* disabled */
out_be32 (&mm->sdram1, 0x10000000);
/* setup config registers */
out_be32 (&sdram->config1, SDRAM_CONFIG1);
out_be32 (&sdram->config2, SDRAM_CONFIG2);
#if defined(SDRAM_DDR) && defined(SDRAM_TAPDELAY)
/* set tap delay */
out_be32 (&cdm->porcfg, SDRAM_TAPDELAY);
#endif
/* find RAM size using SDRAM CS0 only */
sdram_start(0);
test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000);
sdram_start(1);
test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000);
if (test1 > test2) {
sdram_start(0);
dramsize = test1;
} else
dramsize = test2;
/* memory smaller than 1MB is impossible */
if (dramsize < (1 << 20))
dramsize = 0;
/* set SDRAM CS0 size according to the amount of RAM found */
if (dramsize > 0) {
out_be32 (&mm->sdram0,
(0x13 + __builtin_ffs(dramsize >> 20) - 1));
} else {
/* disabled */
out_be32 (&mm->sdram0, 0);
}
#else /* CONFIG_SYS_RAMBOOT */
/* retrieve size of memory connected to SDRAM CS0 */
dramsize = in_be32(&mm->sdram0) & 0xFF;
if (dramsize >= 0x13)
dramsize = (1 << (dramsize - 0x13)) << 20;
else
dramsize = 0;
/* retrieve size of memory connected to SDRAM CS1 */
dramsize2 = in_be32(&mm->sdram1) & 0xFF;
if (dramsize2 >= 0x13)
dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
else
dramsize2 = 0;
#endif /* CONFIG_SYS_RAMBOOT */
return dramsize + dramsize2;
}
int checkboard(void)
{
puts("Board: phyCORE-MPC5200B-tiny\n");
return 0;
}
#ifdef CONFIG_PCI
static struct pci_controller hose;
extern void pci_mpc5xxx_init(struct pci_controller *);
void pci_init_board(void)
{
pci_mpc5xxx_init(&hose);
}
#endif
#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t * bd)
{
ft_cpu_setup(blob, bd);
}
#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
#define GPIO_PSC2_4 0x02000000UL
void init_ide_reset(void)
{
volatile struct mpc5xxx_wu_gpio *wu_gpio =
(struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
debug("init_ide_reset\n");
/* Configure PSC2_4 as GPIO output for ATA reset */
setbits_be32(&wu_gpio->enable, GPIO_PSC2_4);
setbits_be32(&wu_gpio->ddr, GPIO_PSC2_4);
/* Deassert reset */
setbits_be32(&wu_gpio->dvo, GPIO_PSC2_4);
}
void ide_set_reset(int idereset)
{
volatile struct mpc5xxx_wu_gpio *wu_gpio =
(struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
debug("ide_reset(%d)\n", idereset);
if (idereset) {
clrbits_be32(&wu_gpio->dvo, GPIO_PSC2_4);
/* Make a delay. MPC5200 spec says 25 usec min */
udelay(500000);
} else
setbits_be32(&wu_gpio->dvo, GPIO_PSC2_4);
}
#endif /* defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET) */