These changes were identified by HighSmith Bill ,Mazzyar and Joseph for
DDR configuration in u-boot code. Some are related to performance, some
affect stability and some correct few basic errors in the current
configuration.
The changes have been tested and found to give better memory latency
figures on MPC8313eRDB.LMBench figures prove it.
The changes are:
- CS0_CONFIG[ AP_n_EN] is changed from 1 to 0
(this may improve performance for application with many read
or write to open pages).
- CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to
001 (activating all the CS when only one is used may cause
unwanted noise on the system)
- TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on
Tras=45ns)
- TIMING_CFG_1[REFREC] changed from 21 clks to 18clks.
- TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to
comply with the 3 ODT clk requirements)
- TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4.
- TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks.
- DDR_SDRAM_MODE[AL]changed from 0 to 1.
- DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks.
- DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510.
- DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500.
The patch is based of git://www.denx.de/git/u-boot-mpc83xx.git
The last commit on this tree was 6775c68683
Signed-off-by: Poonam Aggrwal-b10812 <b10812@freescale.com>
Cc: Bill HighSmith <Bill.Highsmith@freescale.com>
Cc: Razzaz Mazyar <MRazzaz@freescale.com>
Cc: Josep P J <PJ.Joseph@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
562 lines
17 KiB
C
562 lines
17 KiB
C
/*
|
|
* Copyright (C) Freescale Semiconductor, Inc. 2006.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
/*
|
|
* mpc8313epb board configuration file
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_E300 1
|
|
#define CONFIG_MPC83XX 1
|
|
#define CONFIG_MPC831X 1
|
|
#define CONFIG_MPC8313 1
|
|
#define CONFIG_MPC8313ERDB 1
|
|
|
|
#define CONFIG_PCI
|
|
#define CONFIG_83XX_GENERIC_PCI
|
|
|
|
#ifdef CFG_66MHZ
|
|
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
|
|
#elif defined(CFG_33MHZ)
|
|
#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
|
|
#else
|
|
#error Unknown oscillator frequency.
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
|
|
|
|
#define CFG_IMMR 0xE0000000
|
|
|
|
#define CFG_MEMTEST_START 0x00001000
|
|
#define CFG_MEMTEST_END 0x07f00000
|
|
|
|
/* Early revs of this board will lock up hard when attempting
|
|
* to access the PMC registers, unless a JTAG debugger is
|
|
* connected, or some resistor modifications are made.
|
|
*/
|
|
#define CFG_8313ERDB_BROKEN_PMC 1
|
|
|
|
#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
|
|
#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
|
|
|
|
/*
|
|
* DDR Setup
|
|
*/
|
|
#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
|
|
#define CFG_SDRAM_BASE CFG_DDR_BASE
|
|
#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
|
|
|
|
/*
|
|
* Manually set up DDR parameters, as this board does not
|
|
* seem to have the SPD connected to I2C.
|
|
*/
|
|
#define CFG_DDR_SIZE 128 /* MB */
|
|
#define CFG_DDR_CONFIG ( CSCONFIG_EN \
|
|
| 0x00010000 /* TODO */ \
|
|
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
|
|
/* 0x80010102 */
|
|
|
|
#define CFG_DDR_TIMING_3 0x00000000
|
|
#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
|
|
| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
|
|
| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
|
|
| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
|
|
| ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
|
|
| ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
|
|
| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
|
|
| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
|
|
/* 0x00220802 */
|
|
#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
|
|
| ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
|
|
| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
|
|
| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
|
|
| (10 << TIMING_CFG1_REFREC_SHIFT ) \
|
|
| ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
|
|
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
|
|
| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
|
|
/* 0x3835a322 */
|
|
#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
|
|
| ( 5 << TIMING_CFG2_CPO_SHIFT ) \
|
|
| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
|
|
| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
|
|
| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
|
|
| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
|
|
| ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) )
|
|
/* 0x129048c6 */ /* P9-45,may need tuning */
|
|
#define CFG_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \
|
|
| ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
|
|
/* 0x05100500 */
|
|
#if defined(CONFIG_DDR_2T_TIMING)
|
|
#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
|
|
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
|
| SDRAM_CFG_2T_EN \
|
|
| SDRAM_CFG_DBW_32 )
|
|
#else
|
|
#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
|
|
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
|
| SDRAM_CFG_32_BE )
|
|
/* 0x43080000 */
|
|
#endif
|
|
#define CFG_SDRAM_CFG2 0x00401000;
|
|
/* set burst length to 8 for 32-bit data path */
|
|
#define CFG_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
|
|
| ( 0x0632 << SDRAM_MODE_SD_SHIFT ) )
|
|
/* 0x44480632 */
|
|
#define CFG_DDR_MODE_2 0x8000C000;
|
|
|
|
#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
|
|
/*0x02000000*/
|
|
#define CFG_DDRCDR_VALUE ( DDRCDR_EN \
|
|
| DDRCDR_PZ_NOMZ \
|
|
| DDRCDR_NZ_NOMZ \
|
|
| DDRCDR_M_ODR )
|
|
|
|
/*
|
|
* FLASH on the Local Bus
|
|
*/
|
|
#define CFG_FLASH_CFI /* use the Common Flash Interface */
|
|
#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
|
|
#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
|
|
#define CFG_FLASH_SIZE 8 /* flash size in MB */
|
|
#define CFG_FLASH_EMPTY_INFO /* display empty sectors */
|
|
#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
|
|
|
|
#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \
|
|
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
|
|
BR_V) /* valid */
|
|
#define CFG_OR0_PRELIM ( 0xFF000000 /* 16 MByte */ \
|
|
| OR_GPCM_XACS \
|
|
| OR_GPCM_SCY_9 \
|
|
| OR_GPCM_EHTR \
|
|
| OR_GPCM_EAD )
|
|
/* 0xFF006FF7 TODO SLOW 16 MB flash size */
|
|
#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */
|
|
#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */
|
|
|
|
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CFG_MAX_FLASH_SECT 135 /* sectors per device */
|
|
|
|
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
|
|
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
|
|
|
|
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
|
|
#define CFG_RAMBOOT
|
|
#endif
|
|
|
|
#define CFG_INIT_RAM_LOCK 1
|
|
#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
|
|
#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
|
|
|
|
#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
|
|
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
|
|
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
|
|
|
|
/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */
|
|
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
|
|
#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Local Bus LCRR and LBCR regs
|
|
*/
|
|
#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_2 /* 0x00010002 */
|
|
#define CFG_LBC_LBCR ( 0x00040000 /* TODO */ \
|
|
| (0xFF << LBCR_BMT_SHIFT) \
|
|
| 0xF ) /* 0x0004ff0f */
|
|
|
|
#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */
|
|
|
|
/* drivers/mtd/nand/nand.c */
|
|
#define CFG_NAND_BASE 0xE2800000 /* 0xF0000000 */
|
|
#define CFG_MAX_NAND_DEVICE 1
|
|
#define NAND_MAX_CHIPS 1
|
|
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
|
|
|
#define CFG_BR1_PRELIM ( CFG_NAND_BASE \
|
|
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
|
|
| BR_PS_8 /* Port Size = 8 bit */ \
|
|
| BR_MS_FCM /* MSEL = FCM */ \
|
|
| BR_V ) /* valid */
|
|
#define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
|
|
| OR_FCM_CSCT \
|
|
| OR_FCM_CST \
|
|
| OR_FCM_CHT \
|
|
| OR_FCM_SCY_1 \
|
|
| OR_FCM_TRLX \
|
|
| OR_FCM_EHTR )
|
|
/* 0xFFFF8396 */
|
|
#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
|
|
#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
|
|
|
|
#define CFG_VSC7385_BASE 0xF0000000
|
|
|
|
#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */
|
|
#define CFG_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */
|
|
#define CFG_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/
|
|
#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE/* Access window base at VSC7385 base */
|
|
#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */
|
|
|
|
/* local bus read write buffer mapping */
|
|
#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
|
|
#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
|
|
#define CFG_LBLAWBAR3_PRELIM 0xFA000000
|
|
#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */
|
|
|
|
/* pass open firmware flat tree */
|
|
#define CONFIG_OF_LIBFDT 1
|
|
#define CONFIG_OF_BOARD_SETUP 1
|
|
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1
|
|
#define CFG_NS16550
|
|
#define CFG_NS16550_SERIAL
|
|
#define CFG_NS16550_REG_SIZE 1
|
|
#define CFG_NS16550_CLK get_bus_freq(0)
|
|
|
|
#define CFG_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
|
|
#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
|
|
#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
|
|
|
|
/* Use the HUSH parser */
|
|
#define CFG_HUSH_PARSER
|
|
#define CFG_PROMPT_HUSH_PS2 "> "
|
|
|
|
/* I2C */
|
|
#define CONFIG_HARD_I2C /* I2C with hardware support*/
|
|
#define CONFIG_FSL_I2C
|
|
#define CONFIG_I2C_MULTI_BUS
|
|
#define CONFIG_I2C_CMD_TREE
|
|
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CFG_I2C_SLAVE 0x7F
|
|
#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
|
|
#define CFG_I2C_OFFSET 0x3000
|
|
#define CFG_I2C2_OFFSET 0x3100
|
|
|
|
/* TSEC */
|
|
#define CFG_TSEC1_OFFSET 0x24000
|
|
#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
|
|
#define CFG_TSEC2_OFFSET 0x25000
|
|
#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
|
|
#define CONFIG_NET_MULTI
|
|
|
|
/*
|
|
* General PCI
|
|
* Addresses are mapped 1-1.
|
|
*/
|
|
#define CFG_PCI1_MEM_BASE 0x80000000
|
|
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
|
|
#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CFG_PCI1_MMIO_BASE 0x90000000
|
|
#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
|
|
#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
|
|
#define CFG_PCI1_IO_BASE 0x00000000
|
|
#define CFG_PCI1_IO_PHYS 0xE2000000
|
|
#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
|
|
|
|
#define CONFIG_PCI_PNP /* do pci plug-and-play */
|
|
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
|
|
|
|
/*
|
|
* TSEC configuration
|
|
*/
|
|
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
|
|
|
|
#ifndef CONFIG_NET_MULTI
|
|
#define CONFIG_NET_MULTI 1
|
|
#endif
|
|
|
|
#define CONFIG_GMII 1 /* MII PHY management */
|
|
#define CONFIG_TSEC1 1
|
|
|
|
#define CONFIG_TSEC1_NAME "TSEC0"
|
|
#define CONFIG_TSEC2 1
|
|
#define CONFIG_TSEC2_NAME "TSEC1"
|
|
#define TSEC1_PHY_ADDR 0x1c
|
|
#define TSEC2_PHY_ADDR 4
|
|
#define TSEC1_FLAGS TSEC_GIGABIT
|
|
#define TSEC2_FLAGS TSEC_GIGABIT
|
|
#define TSEC1_PHYIDX 0
|
|
#define TSEC2_PHYIDX 0
|
|
|
|
/* Options are: TSEC[0-1] */
|
|
#define CONFIG_ETHPRIME "TSEC1"
|
|
|
|
/*
|
|
* Configure on-board RTC
|
|
*/
|
|
#define CONFIG_RTC_DS1337
|
|
#define CFG_I2C_RTC_ADDR 0x68
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#ifndef CFG_RAMBOOT
|
|
#define CFG_ENV_IS_IN_FLASH 1
|
|
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
|
|
#define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
|
|
#define CFG_ENV_SIZE 0x2000
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#else
|
|
#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
|
|
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
|
|
#define CFG_ENV_SIZE 0x2000
|
|
#endif
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_PCI
|
|
|
|
#if defined(CFG_RAMBOOT)
|
|
#undef CONFIG_CMD_ENV
|
|
#undef CONFIG_CMD_LOADS
|
|
#endif
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1
|
|
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CFG_LONGHELP /* undef to save memory */
|
|
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
|
|
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
|
|
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
|
|
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
|
|
#define CFG_MAXARGS 16 /* max number of command args */
|
|
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
|
|
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
|
|
|
|
#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */
|
|
|
|
#ifdef CFG_66MHZ
|
|
|
|
/* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */
|
|
/* 0x62040000 */
|
|
#define CFG_HRCW_LOW (\
|
|
0x20000000 /* reserved, must be set */ |\
|
|
HRCWL_DDRCM |\
|
|
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
|
|
HRCWL_DDR_TO_SCB_CLK_2X1 |\
|
|
HRCWL_CSB_TO_CLKIN_2X1 |\
|
|
HRCWL_CORE_TO_CSB_2X1)
|
|
|
|
#elif defined(CFG_33MHZ)
|
|
|
|
/* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
|
|
/* 0x65040000 */
|
|
#define CFG_HRCW_LOW (\
|
|
0x20000000 /* reserved, must be set */ |\
|
|
HRCWL_DDRCM |\
|
|
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
|
|
HRCWL_DDR_TO_SCB_CLK_2X1 |\
|
|
HRCWL_CSB_TO_CLKIN_5X1 |\
|
|
HRCWL_CORE_TO_CSB_2X1)
|
|
|
|
#endif
|
|
|
|
/* 0xa0606c00 */
|
|
#define CFG_HRCW_HIGH (\
|
|
HRCWH_PCI_HOST |\
|
|
HRCWH_PCI1_ARBITER_ENABLE |\
|
|
HRCWH_CORE_ENABLE |\
|
|
HRCWH_FROM_0X00000100 |\
|
|
HRCWH_BOOTSEQ_DISABLE |\
|
|
HRCWH_SW_WATCHDOG_DISABLE |\
|
|
HRCWH_ROM_LOC_LOCAL_16BIT |\
|
|
HRCWH_RL_EXT_LEGACY |\
|
|
HRCWH_TSEC1M_IN_RGMII |\
|
|
HRCWH_TSEC2M_IN_RGMII |\
|
|
HRCWH_BIG_ENDIAN |\
|
|
HRCWH_LALE_NORMAL)
|
|
|
|
/* System IO Config */
|
|
#define CFG_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */
|
|
#define CFG_SICRL SICRL_USBDR /* Enable Internal USB Phy */
|
|
|
|
#define CFG_HID0_INIT 0x000000000
|
|
#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
|
|
HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
|
|
|
|
#define CFG_HID2 HID2_HBE
|
|
|
|
/* DDR @ 0x00000000 */
|
|
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10)
|
|
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
/* PCI @ 0x80000000 */
|
|
#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10)
|
|
#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
|
#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
/* PCI2 not supported on 8313 */
|
|
#define CFG_IBAT3L (0)
|
|
#define CFG_IBAT3U (0)
|
|
#define CFG_IBAT4L (0)
|
|
#define CFG_IBAT4U (0)
|
|
|
|
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
|
|
#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
|
#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
|
|
#define CFG_IBAT6L (0xF0000000 | BATL_PP_10)
|
|
#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
#define CFG_IBAT7L (0)
|
|
#define CFG_IBAT7U (0)
|
|
|
|
#define CFG_DBAT0L CFG_IBAT0L
|
|
#define CFG_DBAT0U CFG_IBAT0U
|
|
#define CFG_DBAT1L CFG_IBAT1L
|
|
#define CFG_DBAT1U CFG_IBAT1U
|
|
#define CFG_DBAT2L CFG_IBAT2L
|
|
#define CFG_DBAT2U CFG_IBAT2U
|
|
#define CFG_DBAT3L CFG_IBAT3L
|
|
#define CFG_DBAT3U CFG_IBAT3U
|
|
#define CFG_DBAT4L CFG_IBAT4L
|
|
#define CFG_DBAT4U CFG_IBAT4U
|
|
#define CFG_DBAT5L CFG_IBAT5L
|
|
#define CFG_DBAT5U CFG_IBAT5U
|
|
#define CFG_DBAT6L CFG_IBAT6L
|
|
#define CFG_DBAT6U CFG_IBAT6U
|
|
#define CFG_DBAT7L CFG_IBAT7L
|
|
#define CFG_DBAT7U CFG_IBAT7U
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#define CONFIG_ETHADDR 00:E0:0C:00:95:01
|
|
#define CONFIG_HAS_ETH1
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_ETH1ADDR 00:E0:0C:00:95:02
|
|
|
|
#define CONFIG_IPADDR 10.0.0.2
|
|
#define CONFIG_SERVERIP 10.0.0.1
|
|
#define CONFIG_GATEWAYIP 10.0.0.1
|
|
#define CONFIG_NETMASK 255.0.0.0
|
|
#define CONFIG_NETDEV eth1
|
|
|
|
#define CONFIG_HOSTNAME mpc8313erdb
|
|
#define CONFIG_ROOTPATH /nfs/root/path
|
|
#define CONFIG_BOOTFILE uImage
|
|
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
|
|
#define CONFIG_FDTFILE mpc8313erdb.dtb
|
|
|
|
#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
|
|
#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
#define XMK_STR(x) #x
|
|
#define MK_STR(x) XMK_STR(x)
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=" MK_STR(CONFIG_NETDEV) "\0" \
|
|
"ethprime=TSEC1\0" \
|
|
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
|
|
"tftpflash=tftpboot $loadaddr $uboot; " \
|
|
"protect off " MK_STR(TEXT_BASE) " +$filesize; " \
|
|
"erase " MK_STR(TEXT_BASE) " +$filesize; " \
|
|
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
|
|
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
|
|
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
|
|
"fdtaddr=400000\0" \
|
|
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
|
|
"console=ttyS0\0" \
|
|
"setbootargs=setenv bootargs " \
|
|
"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
|
|
"setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
|
|
"root=$rootdev rw console=$console,$baudrate $othbootargs\0"
|
|
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
|
"setenv rootdev /dev/nfs;" \
|
|
"run setbootargs;" \
|
|
"run setipargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
|
"setenv rootdev /dev/ram;" \
|
|
"run setbootargs;" \
|
|
"tftp $ramdiskaddr $ramdiskfile;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
|
|
#undef MK_STR
|
|
#undef XMK_STR
|
|
|
|
#endif /* __CONFIG_H */
|