u-boot/board/spc1920/spc1920.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

249 lines
6.3 KiB
C

/*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <common.h>
#include <mpc8xx.h>
#include "pld.h"
#include "hpi.h"
#define _NOT_USED_ 0xFFFFFFFF
static long int dram_size (long int, long int *, long int);
const uint sdram_table[] = {
/*
* Single Read. (Offset 0 in UPMB RAM)
*/
0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
0x1FF77C47, /* last */
/*
* SDRAM Initialization (offset 5 in UPMB RAM)
*
* This is no UPM entry point. The following definition uses
* the remaining space to establish an initialization
* sequence, which is executed by a RUN command.
*
*/
0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
/*
* Burst Read. (Offset 8 in UPMB RAM)
*/
0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Single Write. (Offset 18 in UPMB RAM)
*/
0x1F07FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Burst Write. (Offset 20 in UPMB RAM)
*/
0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
_NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Refresh (Offset 30 in UPMB RAM)
*/
0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
0xFFFFFC84, 0xFFFFFC07, /* last */
_NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Exception. (Offset 3c in UPMB RAM)
*/
0x7FFFFC07, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_,
};
phys_size_t initdram (int board_type)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
/* volatile spc1920_pld_t *pld = (spc1920_pld_t *) CONFIG_SYS_SPC1920_PLD_BASE; */
long int size_b0;
long int size8, size9;
int i;
/*
* Configure UPMB for SDRAM
*/
upmconfig (UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
udelay(100);
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
/* burst length=4, burst type=sequential, CAS latency=2 */
memctl->memc_mar = CONFIG_SYS_MAR;
/*
* Map controller bank 1 to the SDRAM bank at preliminary address.
*/
memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
/* initialize memory address register */
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL; /* refresh not enabled yet */
/* mode initialization (offset 5) */
udelay (200); /* 0x80006105 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x05);
/* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
udelay (1); /* 0x80006130 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
udelay (1); /* 0x80006130 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
udelay (1); /* 0x80006106 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x06);
memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
udelay (200);
/* Need at least 10 DRAM accesses to stabilize */
for (i = 0; i < 10; ++i) {
volatile unsigned long *addr =
(volatile unsigned long *) CONFIG_SYS_SDRAM_BASE;
unsigned long val;
val = *(addr + i);
*(addr + i) = val;
}
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CONFIG_SYS_MBMR_8COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CONFIG_SYS_MBMR_9COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
memctl->memc_mbmr = CONFIG_SYS_MBMR_9COL | MBMR_PTBE;
udelay (500);
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
udelay (500);
}
/*
* Final mapping:
*/
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) |
OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
udelay (1000);
/* initalize the DSP Host Port Interface */
hpi_init();
/* FRAM Setup */
memctl->memc_or4 = CONFIG_SYS_OR4;
memctl->memc_br4 = CONFIG_SYS_BR4;
udelay(1000);
return (size_b0);
}
/*
* Check memory range for valid RAM. A simple memory test determines
* the actually available RAM size between addresses `base' and
* `base + maxsize'. Some (not all) hardware errors are detected:
* - short between address lines
* - short between data lines
*/
static long int dram_size (long int mbmr_value, long int *base,
long int maxsize)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
memctl->memc_mbmr = mbmr_value;
return (get_ram_size (base, maxsize));
}
/************* other stuff ******************/
int board_early_init_f(void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
/* Set Go/NoGo led (PA15) to color red */
immap->im_ioport.iop_papar &= ~0x1;
immap->im_ioport.iop_paodr &= ~0x1;
immap->im_ioport.iop_padir |= 0x1;
immap->im_ioport.iop_padat |= 0x1;
#if 0
/* Turn on LED PD9 */
immap->im_ioport.iop_pdpar &= ~(0x0040);
immap->im_ioport.iop_pddir |= 0x0040;
immap->im_ioport.iop_pddat |= 0x0040;
#endif
/*
* Enable console on SMC1. This requires turning on
* the com2_en signal and SMC1_DISABLE
*/
/* SMC1_DISABLE: PB17 */
immap->im_cpm.cp_pbodr &= ~0x4000;
immap->im_cpm.cp_pbpar &= ~0x4000;
immap->im_cpm.cp_pbdir |= 0x4000;
immap->im_cpm.cp_pbdat &= ~0x4000;
/* COM2_EN: PD10 */
immap->im_ioport.iop_pdpar &= ~0x0020;
immap->im_ioport.iop_pddir &= ~0x4000;
immap->im_ioport.iop_pddir |= 0x0020;
immap->im_ioport.iop_pddat |= 0x0020;
#ifdef CONFIG_SYS_SMC1_PLD_CLK4 /* SMC1 uses CLK4 from PLD */
immap->im_cpm.cp_simode |= 0x7000;
immap->im_cpm.cp_simode &= ~(0x8000);
#endif
return 0;
}
int last_stage_init(void)
{
#ifdef CONFIG_SPC1920_HPI_TEST
printf("CMB1920 Host Port Interface Test: %s\n",
hpi_test() ? "Failed!" : "OK");
#endif
return 0;
}
int checkboard (void)
{
puts("Board: SPC1920\n");
return 0;
}