u-boot/board/jse/init.S
Wolfgang Denk 1b387ef55c SPDX: fix IBM-pibs license identifier
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license.  However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word.  I'd prefer
to be consistent to this end".

Change the license IDs to use the official name.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-09-20 10:30:54 -04:00

76 lines
2.8 KiB
ArmAsm

/*
* SPDX-License-Identifier: GPL-2.0 IBM-pibs
*/
/*------------------------------------------------------------------------- */
/* Function: ext_bus_cntlr_init */
/* Description: Initializes the External Bus Controller for the external */
/* peripherals. IMPORTANT: For pass1 this code must run from */
/* cache since you can not reliably change a peripheral banks */
/* timing register (pbxap) while running code from that bank. */
/* For ex., since we are running from ROM on bank 0, we can NOT */
/* execute the code that modifies bank 0 timings from ROM, so */
/* we run it from cache. */
/* */
/* */
/* The layout for the PEI JSE board: */
/* Bank 0 - Flash and SRAM */
/* Bank 1 - SystemACE */
/* Bank 2 - not used */
/* Bank 3 - not used */
/* Bank 4 - not used */
/* Bank 5 - not used */
/* Bank 6 - not used */
/* Bank 7 - not used */
/*------------------------------------------------------------------------- */
#include <asm/ppc4xx.h>
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#include <asm/cache.h>
#include <asm/mmu.h>
.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
mflr r4 /* save link register */
bl ..getAddr
..getAddr:
mflr r3 /* get address of ..getAddr */
mtlr r4 /* restore link register */
addi r4,0,14 /* set ctr to 10; used to prefetch */
mtctr r4 /* 10 cache lines to fit this function */
/* in cache (gives us 8x10=80 instrctns) */
..ebcloop:
icbt r0,r3 /* prefetch cache line for addr in r3 */
addi r3,r3,32 /* move to next cache line */
bdnz ..ebcloop /* continue for 10 cache lines */
/*----------------------------------------------------------------- */
/* Delay to ensure all accesses to ROM are complete before changing */
/* bank 0 timings. 200usec should be enough. */
/* 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles */
/*----------------------------------------------------------------- */
addis r3,0,0x0
ori r3,r3,0xA000 /* ensure 200usec have passed since reset */
mtctr r3
..spinlp:
bdnz ..spinlp /* spin loop */
/*----------------------------------------------------------------- */
/* Memory Bank 0 (Flash) initialization */
/*----------------------------------------------------------------- */
addi r4,0,PB1AP
mtdcr EBC0_CFGADDR,r4
addis r4,0,0x9B01
ori r4,r4,0x5480
mtdcr EBC0_CFGDATA,r4
addi r4,0,PB0CR
mtdcr EBC0_CFGADDR,r4
addis r4,0,0xFFF1 /* BAS=0xFFF,BS=0x0(1MB),BU=0x3(R/W), */
ori r4,r4,0x8000 /* BW=0x0( 8 bits) */
mtdcr EBC0_CFGDATA,r4
blr