u-boot/board/scb9328/flash.c
Wolfgang Denk 0060517ae0 cppcheck cleanup: fix nullPointer errors
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.

Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-11-07 16:27:07 -05:00

311 lines
7.5 KiB
C

/*
* Copyright (C) 2003 ETC s.r.o.
*
* This code was inspired by Marius Groeger and Kyle Harris code
* available in other board ports for U-Boot
*
* SPDX-License-Identifier: GPL-2.0+
*
* Written by Peter Figuli <peposh@etc.sk>, 2003.
*/
#include <common.h>
#include "intel.h"
/*
* This code should handle CFI FLASH memory device. This code is very
* minimalistic approach without many essential error handling code as well.
* Because U-Boot actually is missing smart handling of FLASH device,
* we just set flash_id to anything else to FLASH_UNKNOW, so common code
* can call us without any restrictions.
* TODO: Add CFI Query, to be able to determine FLASH device.
* TODO: Add error handling code
* NOTE: This code was tested with BUS_WIDTH 4 and ITERLEAVE 2 only, but
* hopefully may work with other configurations.
*/
#if ( SCB9328_FLASH_BUS_WIDTH == 1 )
# define FLASH_BUS vu_char
# define FLASH_BUS_RET u_char
# if ( SCB9328_FLASH_INTERLEAVE == 1 )
# define FLASH_CMD( x ) x
# else
# error "With 8bit bus only one chip is allowed"
# endif
#elif ( SCB9328_FLASH_BUS_WIDTH == 2 )
# define FLASH_BUS vu_short
# define FLASH_BUS_RET u_short
# if ( SCB9328_FLASH_INTERLEAVE == 1 )
# define FLASH_CMD( x ) x
# elif ( SCB9328_FLASH_INTERLEAVE == 2 )
# define FLASH_CMD( x ) (( x << 8 )| x )
# else
# error "With 16bit bus only 1 or 2 chip(s) are allowed"
# endif
#elif ( SCB9328_FLASH_BUS_WIDTH == 4 )
# define FLASH_BUS vu_long
# define FLASH_BUS_RET u_long
# if ( SCB9328_FLASH_INTERLEAVE == 1 )
# define FLASH_CMD( x ) x
# elif ( SCB9328_FLASH_INTERLEAVE == 2 )
# define FLASH_CMD( x ) (( x << 16 )| x )
# elif ( SCB9328_FLASH_INTERLEAVE == 4 )
# define FLASH_CMD( x ) (( x << 24 )|( x << 16 ) ( x << 8 )| x )
# else
# error "With 32bit bus only 1,2 or 4 chip(s) are allowed"
# endif
#else
# error "Flash bus width might be 1,2,4 for 8,16,32 bit configuration"
#endif
flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
static FLASH_BUS_RET flash_status_reg (void)
{
FLASH_BUS *addr = (FLASH_BUS *) 0;
/* cppcheck-suppress nullPointer */
*addr = FLASH_CMD (CFI_INTEL_CMD_READ_STATUS_REGISTER);
/* cppcheck-suppress nullPointer */
return *addr;
}
static int flash_ready (ulong timeout)
{
int ok = 1;
ulong start;
start = get_timer(0);
while ((flash_status_reg () & FLASH_CMD (CFI_INTEL_SR_READY)) !=
FLASH_CMD (CFI_INTEL_SR_READY)) {
if (get_timer(start) > timeout && timeout != 0) {
ok = 0;
break;
}
}
return ok;
}
#if ( CONFIG_SYS_MAX_FLASH_BANKS != 1 )
# error "SCB9328 platform has only one flash bank!"
#endif
ulong flash_init (void)
{
int i;
unsigned long address = SCB9328_FLASH_BASE;
flash_info[0].size = SCB9328_FLASH_BANK_SIZE;
flash_info[0].sector_count = CONFIG_SYS_MAX_FLASH_SECT;
flash_info[0].flash_id = INTEL_MANUFACT;
memset (flash_info[0].protect, 0, CONFIG_SYS_MAX_FLASH_SECT);
for (i = 0; i < CONFIG_SYS_MAX_FLASH_SECT; i++) {
flash_info[0].start[i] = address;
#ifdef SCB9328_FLASH_UNLOCK
/* Some devices are hw locked after start. */
*((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_LOCK_SETUP);
*((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_UNLOCK_BLOCK);
flash_ready (0);
*((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
#endif
address += SCB9328_FLASH_SECT_SIZE;
}
flash_protect (FLAG_PROTECT_SET,
CONFIG_SYS_FLASH_BASE,
CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1,
&flash_info[0]);
flash_protect (FLAG_PROTECT_SET,
CONFIG_ENV_ADDR,
CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
return SCB9328_FLASH_BANK_SIZE;
}
void flash_print_info (flash_info_t * info)
{
int i;
printf (" Intel vendor\n");
printf (" Size: %ld MB in %d Sectors\n",
info->size >> 20, info->sector_count);
printf (" Sector Start Addresses:");
for (i = 0; i < info->sector_count; i++) {
if (!(i % 5)) {
printf ("\n");
}
printf (" %08lX%s", info->start[i],
info->protect[i] ? " (RO)" : " ");
}
printf ("\n");
}
int flash_erase (flash_info_t * info, int s_first, int s_last)
{
int flag, non_protected = 0, sector;
int rc = ERR_OK;
FLASH_BUS *address;
for (sector = s_first; sector <= s_last; sector++) {
if (!info->protect[sector]) {
non_protected++;
}
}
if (!non_protected) {
return ERR_PROTECTED;
}
/*
* Disable interrupts which might cause a timeout
* here. Remember that our exception vectors are
* at address 0 in the flash, and we don't want a
* (ticker) exception to happen while the flash
* chip is in programming mode.
*/
flag = disable_interrupts ();
/* Start erase on unprotected sectors */
for (sector = s_first; sector <= s_last && !ctrlc (); sector++) {
if (info->protect[sector]) {
printf ("Protected sector %2d skipping...\n", sector);
continue;
} else {
printf ("Erasing sector %2d ... ", sector);
}
address = (FLASH_BUS *) (info->start[sector]);
*address = FLASH_CMD (CFI_INTEL_CMD_BLOCK_ERASE);
*address = FLASH_CMD (CFI_INTEL_CMD_CONFIRM);
if (flash_ready (CONFIG_SYS_FLASH_ERASE_TOUT)) {
*address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER);
printf ("ok.\n");
} else {
*address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND);
rc = ERR_TIMOUT;
printf ("timeout! Aborting...\n");
break;
}
*address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
}
if (ctrlc ())
printf ("User Interrupt!\n");
/* allow flash to settle - wait 10 ms */
udelay_masked (10000);
if (flag) {
enable_interrupts ();
}
return rc;
}
static int write_data (flash_info_t * info, ulong dest, FLASH_BUS data)
{
FLASH_BUS *address = (FLASH_BUS *) dest;
int rc = ERR_OK;
int flag;
/* Check if Flash is (sufficiently) erased */
if ((*address & data) != data) {
return ERR_NOT_ERASED;
}
/*
* Disable interrupts which might cause a timeout
* here. Remember that our exception vectors are
* at address 0 in the flash, and we don't want a
* (ticker) exception to happen while the flash
* chip is in programming mode.
*/
flag = disable_interrupts ();
*address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER);
*address = FLASH_CMD (CFI_INTEL_CMD_PROGRAM1);
*address = data;
if (!flash_ready (CONFIG_SYS_FLASH_WRITE_TOUT)) {
*address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND);
rc = ERR_TIMOUT;
printf ("timeout! Aborting...\n");
}
*address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
if (flag) {
enable_interrupts ();
}
return rc;
}
int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
{
ulong read_addr, write_addr;
FLASH_BUS data;
int i, result = ERR_OK;
read_addr = addr & ~(sizeof (FLASH_BUS) - 1);
write_addr = read_addr;
if (read_addr != addr) {
data = 0;
for (i = 0; i < sizeof (FLASH_BUS); i++) {
if (read_addr < addr || cnt == 0) {
data |= *((uchar *) read_addr) << i * 8;
} else {
data |= (*src++) << i * 8;
cnt--;
}
read_addr++;
}
if ((result = write_data (info, write_addr, data)) != ERR_OK) {
return result;
}
write_addr += sizeof (FLASH_BUS);
}
for (; cnt >= sizeof (FLASH_BUS); cnt -= sizeof (FLASH_BUS)) {
if ((result = write_data (info, write_addr,
*((FLASH_BUS *) src))) != ERR_OK) {
return result;
}
write_addr += sizeof (FLASH_BUS);
src += sizeof (FLASH_BUS);
}
if (cnt > 0) {
read_addr = write_addr;
data = 0;
for (i = 0; i < sizeof (FLASH_BUS); i++) {
if (cnt > 0) {
data |= (*src++) << i * 8;
cnt--;
} else {
data |= *((uchar *) read_addr) << i * 8;
}
read_addr++;
}
if ((result = write_data (info, write_addr, data)) != 0) {
return result;
}
}
return ERR_OK;
}