u-boot/board/freescale/ls2080ardb
York Sun e61a7534e3 armv8: Move secure_ram variable out of generic global data
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-07-15 09:01:43 -07:00
..
ddr.c armv8: Move secure_ram variable out of generic global data 2016-07-15 09:01:43 -07:00
ddr.h board/freescale: Update ddr clk_adjust 2016-06-03 14:06:57 -07:00
eth_ls2080rdb.c board: ls2080a: Add "mcinitcmd" env for MC & DPL deployment 2016-06-10 13:44:58 -07:00
Kconfig armv8: LS2080A: Rename LS2085A to reflect LS2080A 2015-11-30 08:53:04 -08:00
ls2080ardb.c usb: xhci: fsl: Add workaround for USB erratum A008751 2016-06-13 15:16:46 +02:00
ls2080ardb_qixis.h armv8: LS2080A: Rename LS2085A to reflect LS2080A 2015-11-30 08:53:04 -08:00
MAINTAINERS armv8: ls2080a: Update MAINTAINERS file 2016-05-17 09:27:15 -07:00
Makefile armv8: LS2080A: Rename LS2085A to reflect LS2080A 2015-11-30 08:53:04 -08:00
README armv8: fsl-layerscape: Organize SoC overview at common location 2016-06-03 14:12:50 -07:00

Overview
--------
The LS2080A Reference Design (RDB) is a high-performance computing,
evaluation, and development platform that supports the QorIQ LS2080A
Layerscape Architecture processor.

LS2080A SoC Overview
--------------------
Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A
SoC overview.

 LS2080ARDB board Overview
 -----------------------
 - SERDES Connections, 16 lanes supporting:
      - PCI Express - 3.0
      - SATA 3.0
      - XFI
 - DDR Controller
     - Two ports of 72-bits (8-bits ECC) DDR4. Each port supports four
       chip-selects and two DIMM connectors. Support is up to 2133MT/s.
     - One port of 40-bits (8-bits ECC) DDR4 which supports four chip-selects
       and two DIMM connectors. Support is up to 1600MT/s.
 -IFC/Local Bus
    - IFC rev. 2.0 implementation supporting Little Endian connection scheme.
    - 128 MB NOR flash 16-bit data bus
    - One 2 GB NAND flash with ECC support
    - CPLD connection
 - USB 3.0
    - Two high speed USB 3.0 ports
    - First USB 3.0 port configured as Host with Type-A connector
    - Second USB 3.0 port configured as OTG with micro-AB connector
 - SDHC adapter
    - SD Card Rev 2.0 and Rev 3.0
 - DSPI
    - 128 MB high-speed flash Memory for boot code and storage (up to 108MHz)
 - 4 I2C controllers
 - Two SATA onboard connectors
 - UART
 - ARM JTAG support

Memory map from core's view
----------------------------
0x00_0000_0000 .. 0x00_000F_FFFF	Boot Rom
0x00_0100_0000 .. 0x00_0FFF_FFFF	CCSR
0x00_1800_0000 .. 0x00_181F_FFFF	OCRAM
0x00_3000_0000 .. 0x00_3FFF_FFFF	IFC region #1
0x00_8000_0000 .. 0x00_FFFF_FFFF	DDR region #1
0x05_1000_0000 .. 0x05_FFFF_FFFF	IFC region #2
0x80_8000_0000 .. 0xFF_FFFF_FFFF	DDR region #2

Other addresses are either reserved, or not used directly by U-Boot.
This list should be updated when more addresses are used.

IFC region map from core's view
-------------------------------
During boot i.e. IFC Region #1:-
  0x30000000 - 0x37ffffff : 128MB : NOR flash
  0x3C000000 - 0x40000000 : 64MB  : CPLD

After relocate to DDR i.e. IFC Region #2:-
  0x5_1000_0000..0x5_1fff_ffff	Memory Hole
  0x5_2000_0000..0x5_3fff_ffff	IFC CSx (CPLD, NAND and others 512MB)
  0x5_4000_0000..0x5_7fff_ffff	ASIC or others 1GB
  0x5_8000_0000..0x5_bfff_ffff	IFC CS0 1GB (NOR/Promjet)
  0x5_C000_0000..0x5_ffff_ffff	IFC CS1 1GB (NOR/Promjet)

Booting Options
---------------
a) NOR boot
b) NAND boot

Booting Linux flavors which do not support 48-bit VA (< Linux 3.18)
-------------------------------------------------------------------
One needs to use appropriate bootargs to boot Linux flavors which do
not support 48-bit VA (for e.g. < Linux 3.18) by appending mem=2048M, as shown
below:

=> setenv bootargs 'console=ttyS1,115200 root=/dev/ram
   earlycon=uart8250,mmio,0x21c0600,115200 default_hugepagesz=2m hugepagesz=2m
   hugepages=16 mem=2048M'