u-boot/board/ttcontrol/vision2/vision2.c
Eric Nelson 3acb011c3c ARM: i.MX: provide declaration for board_spi_cs_gpio
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-21 10:47:14 +02:00

573 lines
15 KiB
C

/*
* (C) Copyright 2010
* Stefano Babic, DENX Software Engineering, sbabic@denx.de.
*
* (C) Copyright 2009 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/clock.h>
#include <asm/arch/iomux-mx51.h>
#include <asm/gpio.h>
#include <asm/arch/sys_proto.h>
#include <asm/imx-common/spi.h>
#include <i2c.h>
#include <mmc.h>
#include <power/pmic.h>
#include <fsl_esdhc.h>
#include <fsl_pmic.h>
#include <mc13892.h>
#include <linux/fb.h>
#include <ipu_pixfmt.h>
DECLARE_GLOBAL_DATA_PTR;
static struct fb_videomode const nec_nl6448bc26_09c = {
"NEC_NL6448BC26-09C",
60, /* Refresh */
640, /* xres */
480, /* yres */
37650, /* pixclock = 26.56Mhz */
48, /* left margin */
16, /* right margin */
31, /* upper margin */
12, /* lower margin */
96, /* hsync-len */
2, /* vsync-len */
0, /* sync */
FB_VMODE_NONINTERLACED, /* vmode */
0, /* flag */
};
#ifdef CONFIG_HW_WATCHDOG
#include <watchdog.h>
void hw_watchdog_reset(void)
{
int val;
/* toggle watchdog trigger pin */
val = gpio_get_value(IMX_GPIO_NR(3, 2));
val = val ? 0 : 1;
gpio_set_value(IMX_GPIO_NR(3, 2), val);
}
#endif
static void init_drive_strength(void)
{
static const iomux_v3_cfg_t ddr_pads[] = {
NEW_PAD_CTRL(MX51_GRP_PKEDDR, 0),
NEW_PAD_CTRL(MX51_GRP_PKEADDR, PAD_CTL_PKE),
NEW_PAD_CTRL(MX51_GRP_DDRAPKS, 0),
NEW_PAD_CTRL(MX51_GRP_DDRAPUS, PAD_CTL_PUS_100K_UP),
NEW_PAD_CTRL(MX51_GRP_DDR_SR_A1, PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_GRP_DDR_A0, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX51_GRP_DDR_A1, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX51_PAD_DRAM_RAS__DRAM_RAS,
PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_DRAM_CAS__DRAM_CAS,
PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_GRP_PKEDDR, PAD_CTL_PKE),
NEW_PAD_CTRL(MX51_GRP_DDRPKS, 0),
NEW_PAD_CTRL(MX51_GRP_HYSDDR0, 0),
NEW_PAD_CTRL(MX51_GRP_HYSDDR1, 0),
NEW_PAD_CTRL(MX51_GRP_HYSDDR2, 0),
NEW_PAD_CTRL(MX51_GRP_HYSDDR3, 0),
NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B0, PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B1, PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B2, PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B4, PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_GRP_DDRPUS, PAD_CTL_PUS_100K_UP),
NEW_PAD_CTRL(MX51_GRP_INMODE1, 0),
NEW_PAD_CTRL(MX51_GRP_DRAM_B0, PAD_CTL_DSE_MED),
NEW_PAD_CTRL(MX51_GRP_DRAM_B1, PAD_CTL_DSE_MED),
NEW_PAD_CTRL(MX51_GRP_DRAM_B2, PAD_CTL_DSE_MED),
NEW_PAD_CTRL(MX51_GRP_DRAM_B4, PAD_CTL_DSE_MED),
NEW_PAD_CTRL(MX51_PAD_DRAM_SDWE__DRAM_SDWE, MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_SDCKE0__DRAM_SDCKE0,
MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_SDCKE1__DRAM_SDCKE1,
MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_SDCLK__DRAM_SDCLK,
MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS0__DRAM_SDQS0,
MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS1__DRAM_SDQS1,
MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS2__DRAM_SDQS2,
MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS3__DRAM_SDQS3,
MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_CS0__DRAM_CS0, MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_CS1__DRAM_CS1, MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_DQM0__DRAM_DQM0, MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_DQM1__DRAM_DQM1, MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_DQM2__DRAM_DQM2, MX51_GPIO_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_DRAM_DQM3__DRAM_DQM3, MX51_GPIO_PAD_CTRL),
};
imx_iomux_v3_setup_multiple_pads(ddr_pads, ARRAY_SIZE(ddr_pads));
}
int dram_init(void)
{
gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1,
PHYS_SDRAM_1_SIZE);
return 0;
}
static void setup_weim(void)
{
struct weim *pweim = (struct weim *)WEIM_BASE_ADDR;
pweim->cs0gcr1 = 0x004100b9;
pweim->cs0gcr2 = 0x00000001;
pweim->cs0rcr1 = 0x0a018000;
pweim->cs0rcr2 = 0;
pweim->cs0wcr1 = 0x0704a240;
}
static void setup_uart(void)
{
static const iomux_v3_cfg_t uart_pads[] = {
MX51_PAD_EIM_D25__UART3_RXD, /* console RX */
MX51_PAD_EIM_D26__UART3_TXD, /* console TX */
};
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
}
#ifdef CONFIG_MXC_SPI
int board_spi_cs_gpio(unsigned bus, unsigned cs)
{
return (bus == 0 && cs == 1) ? 121 : -1;
}
void spi_io_init(void)
{
static const iomux_v3_cfg_t spi_pads[] = {
NEW_PAD_CTRL(MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI, PAD_CTL_HYS |
PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_CSPI1_MISO__ECSPI1_MISO, PAD_CTL_HYS |
PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_CSPI1_SS0__ECSPI1_SS0, PAD_CTL_HYS |
PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_CSPI1_SS1__ECSPI1_SS1, PAD_CTL_HYS |
PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_DI1_PIN11__ECSPI1_SS2, PAD_CTL_HYS |
PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK, PAD_CTL_HYS |
PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
};
imx_iomux_v3_setup_multiple_pads(spi_pads, ARRAY_SIZE(spi_pads));
}
static void reset_peripherals(int reset)
{
#ifdef CONFIG_VISION2_HW_1_0
static const iomux_v3_cfg_t fec_cfg_pads[] = {
/* RXD1 */
NEW_PAD_CTRL(MX51_PAD_EIM_EB3__GPIO2_23, NO_PAD_CTRL),
/* RXD2 */
NEW_PAD_CTRL(MX51_PAD_EIM_CS2__GPIO2_27, NO_PAD_CTRL),
/* RXD3 */
NEW_PAD_CTRL(MX51_PAD_EIM_CS3__GPIO2_28, NO_PAD_CTRL),
/* RXER */
NEW_PAD_CTRL(MX51_PAD_EIM_CS4__GPIO2_29, NO_PAD_CTRL),
/* COL */
NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__GPIO3_10, NO_PAD_CTRL),
/* RCLK */
NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__GPIO3_11, NO_PAD_CTRL),
/* RXD0 */
NEW_PAD_CTRL(MX51_PAD_NANDF_D9__GPIO3_31, NO_PAD_CTRL),
};
static const iomux_v3_cfg_t fec_pads[] = {
NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2),
NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2),
NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2),
MX51_PAD_NANDF_D9__FEC_RDATA0,
NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4),
MX51_PAD_EIM_CS4__FEC_RX_ER,
NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4),
};
#endif
if (reset) {
/* reset_n is on NANDF_D15 */
gpio_direction_output(IMX_GPIO_NR(3, 25), 0);
#ifdef CONFIG_VISION2_HW_1_0
/*
* set FEC Configuration lines
* set levels of FEC config lines
*/
gpio_direction_output(IMX_GPIO_NR(3, 11), 0);
gpio_direction_output(IMX_GPIO_NR(3, 10), 1);
gpio_direction_output(IMX_GPIO_NR(3, 31), 1);
/* set direction of FEC config lines */
gpio_direction_output(IMX_GPIO_NR(2, 27), 0);
gpio_direction_output(IMX_GPIO_NR(2, 28), 0);
gpio_direction_output(IMX_GPIO_NR(2, 29), 0);
gpio_direction_output(IMX_GPIO_NR(2, 23), 1);
imx_iomux_v3_setup_multiple_pads(fec_cfg_pads,
ARRAY_SIZE(fec_cfg_pads));
#endif
/* activate reset_n pin */
imx_iomux_v3_setup_pad(
NEW_PAD_CTRL(MX51_PAD_NANDF_D15__GPIO3_25,
PAD_CTL_DSE_MAX));
} else {
/* set FEC Control lines */
gpio_direction_input(IMX_GPIO_NR(3, 25));
udelay(500);
#ifdef CONFIG_VISION2_HW_1_0
imx_iomux_v3_setup_multiple_pads(fec_pads,
ARRAY_SIZE(fec_pads));
#endif
}
}
static void power_init_mx51(void)
{
unsigned int val;
struct pmic *p;
int ret;
ret = pmic_init(I2C_PMIC);
if (ret)
return;
p = pmic_get("FSL_PMIC");
if (!p)
return;
/* Write needed to Power Gate 2 register */
pmic_reg_read(p, REG_POWER_MISC, &val);
/* enable VCAM with 2.775V to enable read from PMIC */
val = VCAMCONFIG | VCAMEN;
pmic_reg_write(p, REG_MODE_1, val);
/*
* Set switchers in Auto in NORMAL mode & STANDBY mode
* Setup the switcher mode for SW1 & SW2
*/
pmic_reg_read(p, REG_SW_4, &val);
val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) |
(SWMODE_MASK << SWMODE2_SHIFT)));
val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) |
(SWMODE_AUTO_AUTO << SWMODE2_SHIFT);
pmic_reg_write(p, REG_SW_4, val);
/* Setup the switcher mode for SW3 & SW4 */
pmic_reg_read(p, REG_SW_5, &val);
val &= ~((SWMODE_MASK << SWMODE4_SHIFT) |
(SWMODE_MASK << SWMODE3_SHIFT));
val |= (SWMODE_AUTO_AUTO << SWMODE4_SHIFT) |
(SWMODE_AUTO_AUTO << SWMODE3_SHIFT);
pmic_reg_write(p, REG_SW_5, val);
/* Set VGEN3 to 1.8V, VCAM to 3.0V */
pmic_reg_read(p, REG_SETTING_0, &val);
val &= ~(VCAM_MASK | VGEN3_MASK);
val |= VCAM_3_0;
pmic_reg_write(p, REG_SETTING_0, val);
/* Set VVIDEO to 2.775V, VAUDIO to 3V0, VSD to 1.8V */
pmic_reg_read(p, REG_SETTING_1, &val);
val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK);
val |= VVIDEO_2_775 | VAUDIO_3_0 | VSD_1_8;
pmic_reg_write(p, REG_SETTING_1, val);
/* Configure VGEN3 and VCAM regulators to use external PNP */
val = VGEN3CONFIG | VCAMCONFIG;
pmic_reg_write(p, REG_MODE_1, val);
udelay(200);
/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
VVIDEOEN | VAUDIOEN | VSDEN;
pmic_reg_write(p, REG_MODE_1, val);
pmic_reg_read(p, REG_POWER_CTL2, &val);
val |= WDIRESET;
pmic_reg_write(p, REG_POWER_CTL2, val);
udelay(2500);
}
#endif
static void setup_gpios(void)
{
static const iomux_v3_cfg_t gpio_pads_1[] = {
NEW_PAD_CTRL(MX51_PAD_GPIO1_7__GPIO1_7, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* CAM_SUP_DISn */
NEW_PAD_CTRL(MX51_PAD_DI1_PIN12__GPIO3_1, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* DAB Display EN */
NEW_PAD_CTRL(MX51_PAD_DI1_PIN13__GPIO3_2, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* WDOG_TRIGGER */
};
static const iomux_v3_cfg_t gpio_pads_2[] = {
NEW_PAD_CTRL(MX51_PAD_DI1_D0_CS__GPIO3_3, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* Display2 TxEN */
NEW_PAD_CTRL(MX51_PAD_DI1_D1_CS__GPIO3_4, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* DAB Light EN */
NEW_PAD_CTRL(MX51_PAD_DISPB2_SER_DIN__GPIO3_5, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* AUDIO_MUTE */
NEW_PAD_CTRL(MX51_PAD_DISPB2_SER_DIO__GPIO3_6, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* SPARE_OUT */
NEW_PAD_CTRL(MX51_PAD_NANDF_D14__GPIO3_26, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* BEEPER_EN */
NEW_PAD_CTRL(MX51_PAD_NANDF_D13__GPIO3_27, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* POWER_OFF */
NEW_PAD_CTRL(MX51_PAD_NANDF_D10__GPIO3_30, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* FRAM_WE */
NEW_PAD_CTRL(MX51_PAD_CSPI1_RDY__GPIO4_26, PAD_CTL_PKE |
PAD_CTL_DSE_MED), /* EXPANSION_EN */
MX51_PAD_GPIO1_2__PWM1_PWMO,
};
unsigned int i;
imx_iomux_v3_setup_multiple_pads(gpio_pads_1, ARRAY_SIZE(gpio_pads_1));
/* Now we need to trigger the watchdog */
WATCHDOG_RESET();
imx_iomux_v3_setup_multiple_pads(gpio_pads_2, ARRAY_SIZE(gpio_pads_2));
/*
* Set GPIO1_4 to high and output; it is used to reset
* the system on reboot
*/
gpio_direction_output(IMX_GPIO_NR(1, 4), 1);
gpio_direction_output(IMX_GPIO_NR(1, 7), 0);
for (i = IMX_GPIO_NR(3, 1); i < IMX_GPIO_NR(3, 7); i++)
gpio_direction_output(i, 0);
gpio_direction_output(IMX_GPIO_NR(3, 30), 0);
/* Set POWER_OFF high */
gpio_direction_output(IMX_GPIO_NR(3, 27), 1);
gpio_direction_output(IMX_GPIO_NR(3, 26), 0);
gpio_direction_output(IMX_GPIO_NR(4, 26), 0);
gpio_direction_output(IMX_GPIO_NR(4, 25), 1);
WATCHDOG_RESET();
}
static void setup_fec(void)
{
static const iomux_v3_cfg_t fec_pads[] = {
NEW_PAD_CTRL(MX51_PAD_EIM_EB2__FEC_MDIO, PAD_CTL_HYS |
PAD_CTL_PUS_22K_UP | PAD_CTL_ODE |
PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
MX51_PAD_NANDF_CS3__FEC_MDC,
NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2),
NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2),
NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2),
MX51_PAD_NANDF_D9__FEC_RDATA0,
MX51_PAD_NANDF_CS6__FEC_TDATA3,
MX51_PAD_NANDF_CS5__FEC_TDATA2,
MX51_PAD_NANDF_CS4__FEC_TDATA1,
MX51_PAD_NANDF_D8__FEC_TDATA0,
MX51_PAD_NANDF_CS7__FEC_TX_EN,
MX51_PAD_NANDF_CS2__FEC_TX_ER,
MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK,
NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4),
NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4),
MX51_PAD_EIM_CS5__FEC_CRS,
MX51_PAD_EIM_CS4__FEC_RX_ER,
NEW_PAD_CTRL(MX51_PAD_NANDF_D11__FEC_RX_DV, MX51_PAD_CTRL_4),
};
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
}
struct fsl_esdhc_cfg esdhc_cfg[1] = {
{MMC_SDHC1_BASE_ADDR},
};
int get_mmc_getcd(u8 *cd, struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
*cd = gpio_get_value(IMX_GPIO_NR(1, 0));
else
*cd = 0;
return 0;
}
#ifdef CONFIG_FSL_ESDHC
int board_mmc_init(bd_t *bis)
{
static const iomux_v3_cfg_t sd1_pads[] = {
NEW_PAD_CTRL(MX51_PAD_SD1_CMD__SD1_CMD, PAD_CTL_DSE_MAX |
PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_SD1_CLK__SD1_CLK, PAD_CTL_DSE_MAX |
PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_SD1_DATA0__SD1_DATA0, PAD_CTL_DSE_MAX |
PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_SD1_DATA1__SD1_DATA1, PAD_CTL_DSE_MAX |
PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_SD1_DATA2__SD1_DATA2, PAD_CTL_DSE_MAX |
PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_SD1_DATA3__SD1_DATA3, PAD_CTL_DSE_MAX |
PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_GPIO1_0__SD1_CD, PAD_CTL_HYS),
NEW_PAD_CTRL(MX51_PAD_GPIO1_1__SD1_WP, PAD_CTL_HYS),
};
imx_iomux_v3_setup_multiple_pads(sd1_pads, ARRAY_SIZE(sd1_pads));
esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
}
#endif
void lcd_enable(void)
{
static const iomux_v3_cfg_t lcd_pads[] = {
MX51_PAD_DI1_PIN2__DI1_PIN2,
MX51_PAD_DI1_PIN3__DI1_PIN3,
};
int ret;
imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
gpio_set_value(IMX_GPIO_NR(1, 2), 1);
imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_2__GPIO1_2,
NO_PAD_CTRL));
ret = ipuv3_fb_init(&nec_nl6448bc26_09c, 0, IPU_PIX_FMT_RGB666);
if (ret)
puts("LCD cannot be configured\n");
}
int board_early_init_f(void)
{
init_drive_strength();
/* Setup debug led */
gpio_direction_output(IMX_GPIO_NR(1, 6), 0);
imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6,
PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST));
/* wait a little while to give the pll time to settle */
sdelay(100000);
setup_weim();
setup_uart();
setup_fec();
setup_gpios();
spi_io_init();
return 0;
}
static void backlight(int on)
{
if (on) {
gpio_set_value(IMX_GPIO_NR(3, 1), 1);
udelay(10000);
gpio_set_value(IMX_GPIO_NR(3, 4), 1);
} else {
gpio_set_value(IMX_GPIO_NR(3, 1), 0);
gpio_set_value(IMX_GPIO_NR(3, 4), 0);
}
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
lcd_enable();
backlight(1);
return 0;
}
int board_late_init(void)
{
power_init_mx51();
reset_peripherals(1);
udelay(2000);
reset_peripherals(0);
udelay(2000);
/* Early revisions require a second reset */
#ifdef CONFIG_VISION2_HW_1_0
reset_peripherals(1);
udelay(2000);
reset_peripherals(0);
udelay(2000);
#endif
return 0;
}
/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/
int overwrite_console(void)
{
return 1;
}
int checkboard(void)
{
puts("Board: TTControl Vision II CPU V\n");
return 0;
}
int do_vision_lcd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int on;
if (argc < 2)
return cmd_usage(cmdtp);
on = (strcmp(argv[1], "on") == 0);
backlight(on);
return 0;
}
U_BOOT_CMD(
lcdbl, CONFIG_SYS_MAXARGS, 1, do_vision_lcd,
"Vision2 Backlight",
"lcdbl [on|off]\n"
);