u-boot/include/configs/bf518f-ezbrd.h
Mike Frysinger 912da8d606 Blackfin: bf518f-ezbrd: increase monitor length
The addition of KGDB overflowed the current linker section.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:27 -05:00

149 lines
3.6 KiB
C

/*
* U-boot - Configuration file for BF518F EZBrd board
*/
#ifndef __CONFIG_BF518F_EZBRD_H__
#define __CONFIG_BF518F_EZBRD_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf518-0.0
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 25000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 16
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
/*
* Memory Settings
*/
/* This board has a 64meg MT48H32M16 */
#define CONFIG_MEM_ADD_WDTH 10
#define CONFIG_MEM_SIZE 64
#define CONFIG_EBIU_SDRRC_VAL 0x0096
#define CONFIG_EBIU_SDGCTL_VAL (SCTLE | CL_3 | PASR_ALL | TRAS_6 | TRP_3 | TRCD_3 | TWR_2 | PSS)
#define CONFIG_EBIU_AMGCTL_VAL (AMCKEN | AMBEN_ALL)
#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_15 | B1RAT_15 | B1HT_3 | B1RDYPOL | B0WAT_15 | B0RAT_15 | B0HT_3 | B0RDYPOL)
#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_15 | B3RAT_15 | B3HT_3 | B3RDYPOL | B2WAT_15 | B2RAT_15 | B2HT_3 | B2RDYPOL)
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
/*
* Network Settings
*/
#if !defined(__ADSPBF512__) && !defined(__ADSPBF514__)
#define ADI_CMDS_NETWORK 1
#define CONFIG_BFIN_MAC
#define CONFIG_NETCONSOLE 1
#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_HOSTNAME bf518f-ezbrd
#define CONFIG_PHY_ADDR 3
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
* Flash Settings
*/
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 71
/*
* SPI Settings
*/
#define CONFIG_BFIN_SPI
#define CONFIG_ENV_SPI_MAX_HZ 30000000
#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SST
#define CONFIG_SPI_FLASH_STMICRO
/*
* Env Storage Settings
*/
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET 0x10000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x10000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OFFSET 0x4000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x2000
#endif
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
/*
* I2C Settings
*/
#define CONFIG_BFIN_TWI_I2C 1
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 50000
#define CONFIG_SYS_I2C_SLAVE 0
/*
* SDH Settings
*/
#if !defined(__ADSPBF512__)
#define CONFIG_GENERIC_MMC
#define CONFIG_MMC
#define CONFIG_BFIN_SDH
#endif
/*
* Misc Settings
*/
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif