u-boot/include/spi.h
Guennadi Liakhovetski 38254f45b0 New i.MX31 SPI driver
This is an SPI driver for i.MX and MXC based SoCs from Freescale. So far
only implemented and tested on i.MX31, can with a modified register layout
and definitions be used for i.MX27, I think, MXC CPUs have similar SPI
controllers too.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-18 00:43:23 -07:00

88 lines
3.3 KiB
C

/*
* (C) Copyright 2001
* Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef _SPI_H_
#define _SPI_H_
/* SPI mode flags */
#define SPI_CPHA 0x01 /* clock phase */
#define SPI_CPOL 0x02 /* clock polarity */
#define SPI_MODE_0 (0|0) /* (original MicroWire) */
#define SPI_MODE_1 (0|SPI_CPHA)
#define SPI_MODE_2 (SPI_CPOL|0)
#define SPI_MODE_3 (SPI_CPOL|SPI_CPHA)
#define SPI_CS_HIGH 0x04 /* chipselect active high? */
#define SPI_LSB_FIRST 0x08 /* per-word bits-on-wire */
#define SPI_3WIRE 0x10 /* SI/SO signals shared */
#define SPI_LOOP 0x20 /* loopback mode */
/*
* The function call pointer type used to drive the chip select.
*/
typedef void (*spi_chipsel_type)(int cs);
/*-----------------------------------------------------------------------
* Initialization, must be called once on start up.
*/
void spi_init(void);
/*-----------------------------------------------------------------------
* SPI transfer
*
* This writes "bitlen" bits out the SPI MOSI port and simultaneously clocks
* "bitlen" bits in the SPI MISO port. That's just the way SPI works.
*
* The source of the outgoing bits is the "dout" parameter and the
* destination of the input bits is the "din" parameter. Note that "dout"
* and "din" can point to the same memory location, in which case the
* input data overwrites the output data (since both are buffered by
* temporary variables, this is OK).
*
* If the chipsel() function is not NULL, it is called with a parameter
* of '1' (chip select active) at the start of the transfer and again with
* a parameter of '0' at the end of the transfer.
*
* If the chipsel() function _is_ NULL, it the responsibility of the
* caller to make the appropriate chip select active before calling
* spi_xfer() and making it inactive after spi_xfer() returns.
*
* spi_xfer() interface:
* chipsel: Routine to call to set/clear the chip select:
* if chipsel is NULL, it is not used.
* if(cs), make the chip select active (typically '0').
* if(!cs), make the chip select inactive (typically '1').
* dout: Pointer to a string of bits to send out. The bits are
* held in a byte array and are sent MSB first.
* din: Pointer to a string of bits that will be filled in.
* bitlen: How many bits to write and read.
*
* Returns: 0 on success, not 0 on failure
*/
int spi_xfer(spi_chipsel_type chipsel, int bitlen, uchar *dout, uchar *din);
int spi_select(unsigned int bus, unsigned int dev, unsigned long mode);
#endif /* _SPI_H_ */