u-boot/dtt/adm1021.c
Stefan Roese 0dc018ece1 [PATCH] I2C: Add support for multiple I2C busses for RTC & DTT
This patch switches to the desired I2C bus when the date/dtt
commands are called. This can be configured using the
CFG_RTC_BUS_NUM and/or CFG_DTT_BUS_NUM defines.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-02-20 10:51:26 +01:00

175 lines
3.8 KiB
C

/*
* (C) Copyright 2003
* Murray Jensen, CSIRO-MIT, Murray.Jensen@csiro.au
*
* based on dtt/lm75.c which is ...
*
* (C) Copyright 2001
* Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* Analog Devices's ADM1021
* "Low Cost Microprocessor System Temperature Monitor"
*/
#include <common.h>
#ifdef CONFIG_DTT_ADM1021
#include <i2c.h>
#include <dtt.h>
typedef
struct {
uint i2c_addr:7; /* 7bit i2c chip address */
uint conv_rate:3; /* conversion rate */
uint enable_alert:1; /* enable alert output pin */
uint enable_local:1; /* enable internal temp sensor */
uint max_local:8; /* internal temp maximum */
uint min_local:8; /* internal temp minimum */
uint enable_remote:1; /* enable remote temp sensor */
uint max_remote:8; /* remote temp maximum */
uint min_remote:8; /* remote temp minimum */
}
dtt_cfg_t;
dtt_cfg_t dttcfg[] = CFG_DTT_ADM1021;
int
dtt_read (int sensor, int reg)
{
dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
uchar data;
if (i2c_read(dcp->i2c_addr, reg, 1, &data, 1) != 0)
return -1;
return (int)data;
} /* dtt_read() */
int
dtt_write (int sensor, int reg, int val)
{
dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
uchar data;
data = (uchar)(val & 0xff);
if (i2c_write(dcp->i2c_addr, reg, 1, &data, 1) != 0)
return 1;
return 0;
} /* dtt_write() */
static int
_dtt_init (int sensor)
{
dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
int reg, val;
if (((sensor & 1) == 0 ? dcp->enable_local : dcp->enable_remote) == 0)
return 1; /* sensor is disabled (or rather ignored) */
/*
* Setup High Limit register
*/
if ((sensor & 1) == 0) {
reg = DTT_WRITE_LOC_HIGHLIM;
val = dcp->max_local;
}
else {
reg = DTT_WRITE_REM_HIGHLIM;
val = dcp->max_remote;
}
if (dtt_write (sensor, reg, val) != 0)
return 1;
/*
* Setup Low Limit register
*/
if ((sensor & 1) == 0) {
reg = DTT_WRITE_LOC_LOWLIM;
val = dcp->min_local;
}
else {
reg = DTT_WRITE_REM_LOWLIM;
val = dcp->min_remote;
}
if (dtt_write (sensor, reg, val) != 0)
return 1;
/* shouldn't hurt if the rest gets done twice */
/*
* Setup Conversion Rate register
*/
if (dtt_write (sensor, DTT_WRITE_CONVRATE, dcp->conv_rate) != 0)
return 1;
/*
* Setup configuraton register
*/
val = 0; /* running */
if (dcp->enable_alert == 0)
val |= DTT_CONFIG_ALERT_MASKED; /* mask ALERT pin */
if (dtt_write (sensor, DTT_WRITE_CONFIG, val) != 0)
return 1;
return 0;
} /* _dtt_init() */
int
dtt_init (void)
{
int i;
unsigned char sensors[] = CONFIG_DTT_SENSORS;
const char *const header = "DTT: ";
/* switch to correct I2C bus */
I2C_SET_BUS(CFG_DTT_BUS_NUM);
for (i = 0; i < sizeof(sensors); i++) {
if (_dtt_init(sensors[i]) != 0)
printf ("%s%d FAILED INIT\n", header, i+1);
else
printf ("%s%d is %i C\n", header, i+1,
dtt_get_temp(sensors[i]));
}
return (0);
} /* dtt_init() */
int
dtt_get_temp (int sensor)
{
signed char val;
if ((sensor & 1) == 0)
val = dtt_read(sensor, DTT_READ_LOC_VALUE);
else
val = dtt_read(sensor, DTT_READ_REM_VALUE);
return (int) val;
} /* dtt_get_temp() */
#endif /* CONFIG_DTT_ADM1021 */