nand: Set the A1CR depending on the flash chip used

This means that the U-Boot now needs to stop to set these
values. I have manually tested this with BTS #1 and micron
flash. "MICRON" was printed on the serial console.

nand.c

@@ -362,20 +362,23 @@ nand_read_ecc(void)
 /* Get details of the NAND flash used from the id and the table of NAND
  * devices. */
 static int
-nand_get_details(void)
+nand_get_details(uint8_t *out_manID, uint8_t *out_deviceID)
 {
-	uint32_t deviceID, i, j;
+	uint32_t manID, deviceID, i, j;
 
 	/* Issue device read ID command. */
 	flash_write_cmd(NAND_RDID);
 	flash_write_addr(NAND_RDIDADD);
 
 	/* Read ID bytes */
-	j        = flash_read_data() & 0xFF;
+	manID    = flash_read_data() & 0xFF;
 	deviceID = flash_read_data() & 0xFF;
 	j        = flash_read_data() & 0xFF;
 	j        = flash_read_data() & 0xFF;
 
+	*out_manID = manID;
+	*out_deviceID = deviceID;
+
 	uart_send_str("  ID:");
 	uart_send_hexnum(deviceID, 2);
 	if (nand_info.bus_width == BUS_16BIT)
@@ -481,6 +484,39 @@ nand_get_details(void)
 	return E_FAIL;
 }
 
+static int
+nand_set_a1cr(uint8_t manID, uint8_t deviceID)
+{
+	if (deviceID != 0xA1) {
+		log_info( "Unsupported NAND device" );
+		return E_FAIL;
+	}
+
+	switch (manID) {
+	/* ST/Numonyx */
+	case 0x20:
+		AEMIF->A1CR = 0x1844431C;
+		break;
+	/* Micron */
+	case 0x2C:
+		AEMIF->A1CR = 0x102442EC;
+		break;
+	/* Spansion */
+	case 0x01:
+		AEMIF->A1CR = 0x1844437C;
+		break;
+	/* Toshiba */
+	case 0x98:
+		AEMIF->A1CR = 0x102442DC;
+		break;
+	default:
+		log_info( "Unsupported NAND device" );
+		return E_FAIL;
+	}
+
+	return E_PASS;
+}
+
 static void
 nand_write_spare(uint32_t eccvalue)
 {
@@ -852,6 +888,7 @@ nand_init(void)
 {
 	uint32_t width;
 	uint32_t *CSRegs;
+	uint8_t manID, deviceID;
 
 	log_info("Initializing NAND flash:");
 
@@ -887,7 +924,10 @@ nand_init(void)
 	if (nand_wait_for_ready(NAND_TIMEOUT) != E_PASS)
 		return E_FAIL;
 
-	return nand_get_details();
+	if (nand_get_details(&manID, &deviceID) != E_PASS)
+		return E_FAIL;
+
+	return nand_set_a1cr(manID, deviceID);
 }
 
 static int