https://origsvn.digium.com/svn/asterisk/be/branches/C.2-...
..........
r207316 | rmudgett | 2009-07-17 23:05:05 -0500 (Fri, 17 Jul 2009) | 20 lines
Fixed incoming calls being matched to MSNs without type-of-number prefix added.
For an incoming ISDN call the dialed.number is incorrectly matched against
the configured MSNs in misdn.conf. The numbers passed to the dialplan
include the configured prefix for the dialed.number_type, whereas the
check against the configured MSNs (to decide if the call is accepted at
all), is executed without the configured prefix.
e.g., dialed.number = 241168020, TON = national, configured national
prefix is "0". (This is the TON which is used by ISDN providers in the
Netherlands.)
In chan_misdn.c:cb_events() in case EVENT_SETUP the call to
misdn_cfg_is_msn_valid() uses the unnormalized number 241168020, but 57
lines later the call to read_config() adds the prefix, and the
dialed.number is now 0241168020, which is then used in the dialplan.
misdn_cfg_is_msn_valid() must use the normalized number, too.
JIRA ABE-1912
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@207318 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Sig_analog handles allocating the sub channel for callwaiting, so no longer try
to do it in chan_dahdi. Modified analog_alloc_sub to only mark the sub as
allocated upon success of the alloc_sub callback, which was responsible for the
segfault. Also, the callwaiting and callwaitingcallerid options were being
unconditionally set to true. Now, the options are properly set from
chan_dahdi.conf.
(closes issue #15508)
Reported by: elguero
Tested by: elguero
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206998 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r206938 | dvossel | 2009-07-17 11:05:06 -0500 (Fri, 17 Jul 2009) | 14 lines
SIP incorrect From: header information when callpres is prohib
Some ITSP make use of the "Anonymous" display name to detect a
requirement to withhold caller id across the PSTN. This does
not work if the display name is "Unknown".
(closes issue #14465)
Reported by: Nick_Lewis
Patches:
chan_sip.c-callerpres.patch uploaded by Nick (license 657)
chan_sip.c-callerpres_trunk.patch uploaded by dvossel (license 671)
Tested by: Nick_Lewis, dvossel
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206939 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This readds the proper setting of the flag and is really a continuation of
r205731. The flag was being set properly in sig_analog, but use of the
newly added set_dialing callback allowed for some simplification in
chan_dahdi.
(closes issue #15486)
Reported by: rmudgett
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206767 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
................
r206706 | rmudgett | 2009-07-15 15:44:55 -0500 (Wed, 15 Jul 2009) | 26 lines
Merged revision 206700 from
https://origsvn.digium.com/svn/asterisk/be/branches/C.2-...
..........
Fixed chan_misdn crash because mISDNuser library is not thread safe.
With Asterisk the mISDNuser library is driven by two threads concurrently:
1. channels/misdn/isdn_lib.c::manager_event_handler()
2. channels/misdn/isdn_lib.c::misdn_lib_isdn_event_catcher()
Calls into the library are done concurrently and recursively from
isdn_lib.c.
Both threads can fiddle with the master/child layer3_proc_t lists. One
thread may traverse the list when the other interrupts it and then removes
the list element which the first thread was currently handling. This is
exactly what caused the crash. About 60 calls were needed to a Gigaset
CX475 before it occurred once.
This patch adds locking when calling into the mISDNuser library.
This also fixes some cb_log calls with wrong port parameter.
JIRA ABE-1913
Patches: misdn-locking.patch (Modified with mostly cosmetic changes)
..........
................
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206707 65c4cc65-6c06-0410-ace0-fbb531ad65f3
A domain only sip uri <sip:123.123.123.123> would return
123.123.123.123 as callid num. Now, if the username is
missing from a uri, the callerid num field is left empty.
(closes issue #15476)
Reported by: viraptor
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206702 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The main purpose of this commit is to restore missing functionality present in
the ss_thread before all the sig related work was done. Two of the biggest
missing things were distinctive ring detection and cid handling for V23.
fxsoffhookstate and associated mwi variables have been moved inside sig_analog
as they were not being set properly as well.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206566 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r206487 | rmudgett | 2009-07-14 11:44:47 -0500 (Tue, 14 Jul 2009) | 28 lines
Fixes several call transfer issues with chan_misdn.
* issue #14355 - Crash if attempt to transfer a call to an application.
Masquerade the other pair of the four asterisk channels involved in the
two calls. The held call already must be a bridged call (not an
applicaton) or it would have been rejected.
* issue #14692 - Held calls are not automatically cleared after transfer.
Allow the core to initate disconnect of held calls to the ISDN port. This
also fixes a similar case where the party on hold hangs up before being
transferred or taken off hold.
* JIRA ABE-1903 - Orphaned held calls left in music-on-hold.
Do not simply block passing the hangup event on held calls to asterisk
core.
* Fixed to allow held calls to be transferred to ringing calls.
Previously, held calls could only be transferred to connected calls.
* Eliminated unused call states to simplify hangup code.
* Eliminated most uses of "holded" because it is not a word.
(closes issue #14355)
(closes issue #14692)
Reported by: sodom
Patches:
misdn_xfer_v14_r205839.patch uploaded by rmudgett (license 664)
Tested by: rmudgett
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206489 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
................
r206385 | russell | 2009-07-14 09:48:00 -0500 (Tue, 14 Jul 2009) | 13 lines
Merged revisions 206384 via svnmerge from
https://origsvn.digium.com/svn/asterisk/branches/1.2
........
r206384 | russell | 2009-07-14 09:45:47 -0500 (Tue, 14 Jul 2009) | 6 lines
Ensure apathetic replies are sent out on the proper socket.
chan_iax2 supports multiple address bindings. The send_apathetic_reply()
function did not attempt to send its response on the same socket that the
incoming message came in on.
........
................
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206386 65c4cc65-6c06-0410-ace0-fbb531ad65f3
If callbackextension is defined for a peer it successfully causes
a registration to occur, but the registration ignores the
outboundproxy settings for the peer. This patch allows the
peer to be passed to obproxy_get() in transmit_register().
(closes issue #14344)
Reported by: Nick_Lewis
Patches:
callbackextension_peer_trunk.diff uploaded by dvossel (license 671)
Tested by: dvossel
Review: https://reviewboard.asterisk.org/r/294/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@205985 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r205804 | dvossel | 2009-07-10 11:23:59 -0500 (Fri, 10 Jul 2009) | 31 lines
SIP registration auth loop caused by stale nonce
If an endpoint sends two registration requests in a very short
period of time with the same nonce, both receive 401 responses
from Asterisk, each with a different nonce (the second 401
containing the current nonce and the first one being stale).
If the endpoint responds to the first 401, it does not match
the current nonce so Asterisk sends a third 401 with a newly
generated nonce (which updates the current nonce)... Now if
the endpoint responds to the second 401, it does not match the
current nonce either and Asterisk sends a fourth 401 with a
newly generated nonce... This loop goes on and on.
There appears to be a simple fix for this. If the nonce from
the request does not match our nonce, but is a good response
to a previous nonce, instead of sending a 401 with a newly
generated nonce, use the current one instead. This breaks
the loop as the nonce is not updated until a response is
received. Additional logic has been added to make sure no
nonce can be responded to twice though.
(closes issue #15102)
Reported by: Jamuel
Patches:
patch-bug_0015102 uploaded by Jamuel (license 809)
nonce_sip.diff uploaded by dvossel (license 671)
Tested by: Jamuel
Review: https://reviewboard.asterisk.org/r/289/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@205840 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r205775 | mmichelson | 2009-07-10 10:51:36 -0500 (Fri, 10 Jul 2009) | 10 lines
Ensure that outbound NOTIFY requests are properly routed through stateful proxies.
With this change, we make note of Record-Route headers present in any SUBSCRIBE
request that we receive so that our outbound NOTIFY requests will have the proper
Route headers in them.
(closes issue #14725)
Reported by: ibc
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@205776 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Recent changes in T.38 negotiation in Asterisk caused these applications to
not respond when the other endpoint initiated a switchover to T.38; this
resulted in the T.38 switchover failing, and the FAX attempt to be made
using an audio connection, instead of T.38 (which would usually cause the
FAX to fail completely).
This patch corrects this problem, and the applications will now correctly
respond to the T.38 switchover request. In addition, the response will include
the appopriate T.38 session parameters based on what the other end offered
and what our end is capable of.
(closes issue #14849)
Reported by: afosorio
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@205696 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Also go back and wrap all of the places that use the specific reverse charge
APIs with preprocessor conditionals.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204919 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r204834 | rmudgett | 2009-07-02 16:59:43 -0500 (Thu, 02 Jul 2009) | 10 lines
Removed confusing warning message "Got Busy in Connected State"
If an incoming mISDN call is answered with the Answer application and a
subsequent Dial gets a busy endpoint then it is valid for that already
connected channel to get the busy indication. Asterisk will play the busy
tones until the dialplan plays something else or hangs up the call.
(closes issue #11974)
Reported by: fvdb
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204835 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This is a continuation of revision 885 to LibPRI (Capture and expose the Reverse
Charging Indication IE on ISDN PRI) which added the ability to get/set Reverse
Charging Indication in LibPRI. This patch adds the ability to specify RCI on
the outbound leg of a PRI call from within Asterisk, by prefixing the dialed
number with a capital 'C' like:
...,Dial(DAHDI/g1/C4445556666)
And to read it off an inbound channel:
exten => s,1,Set(RCI=${CHANNEL(reversecharge)})
Thanks again to rmudgett for the thorough review.
(closes issue #13760)
Reported by: mrgabu
Review: https://reviewboard.asterisk.org/r/303/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204749 65c4cc65-6c06-0410-ace0-fbb531ad65f3
First of all, the code was unnecessary. The goal was to lock a channel
which was already locked. Second, the assumption of the deadlock avoidance
loop was that the sip_pvt was already locked and we were trying to get the
channel lock. The problem is that the sip_pvt was unlocked a few lines above.
Basically, I'm removing 5 lines of no-op.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204530 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r204300 | mmichelson | 2009-06-29 17:45:34 -0500 (Mon, 29 Jun 2009) | 9 lines
Add error message so that it is clear why a SIP peer was not processed when
a DNS lookup fails on a host or outboundproxy.
(closes issue #13432)
Reported by: p_lindheimer
Patches:
outboundproxy.patch uploaded by p (license 558)
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204301 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r204243 | mmichelson | 2009-06-29 16:23:43 -0500 (Mon, 29 Jun 2009) | 22 lines
Fix a problem where chan_sip would ignore "old" but valid responses.
chan_sip has had a problem for quite a long time that would manifest when
Asterisk would send multiple SIP responses on the same dialog before receiving
a response. The problem occurred because chan_sip only kept track of the highest
outgoing sequence number used on the dialog. If Asterisk sent two requests out,
and a response arrived for the first request sent, then Asterisk would ignore
the response. The result was that Asterisk would continue retransmitting the
requests and ignoring the responses until the maximum number of retransmissions
had been reached.
The fix here is to rearrange the code a bit so that instead of simply comparing
the sequence number of the response to our latest outgoing sequence number, we
walk our list of outstanding packets and determine if there is a match. If there is,
we continue. If not, then we ignore the response.
In doing this, I found a few completely useless variables that I have now removed.
(closes issue #11231)
Reported by: flefoll
Review: https://reviewboard.asterisk.org/r/298
........
r204246 | mmichelson | 2009-06-29 16:37:05 -0500 (Mon, 29 Jun 2009) | 3 lines
Fix build oops.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204247 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r203908 | rmudgett | 2009-06-26 19:55:12 -0500 (Fri, 26 Jun 2009) | 16 lines
The ISDN CPE side should not exclusively pick B channels normally.
Before this patch, Asterisk unconditionally picked B channels exclusively
on the CPE side and normally allowed alternative B channels on the network
side. Now Asterisk does the opposite.
Reasons for the CPE side to normally not pick B channels exclusively:
* For CPE point-to-multipoint mode (i.e. phone side), the CPE side does
not have enough information to exclusively pick B channels. (There may be
other devices on the line.)
* Q.931 gives preference to the network side picking B channels.
* Some telcos require the CPE side to not pick B channels exclusively.
(closes issue #14383)
Reported by: mbrancaleoni
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203909 65c4cc65-6c06-0410-ace0-fbb531ad65f3
after a polarity reversal.
Previously on a polarity switch event chan_dahdi would set the channel
immediately as answered. This would cause problems if a polarity reversal
occurred when the line was picked up as the dial would not have yet occurred.
Now if the polarity reversal occurs before delay has elapsed after coming off
hook or an answer, it is ignored. Also, some refactoring was done in
_handle_event.
(closes issue #13917)
Reported by: alecdavis
Patches:
chan_dahdi.bug13917.feb09.diff2.txt uploaded by alecdavis (license 585)
Tested by: alecdavis
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203672 65c4cc65-6c06-0410-ace0-fbb531ad65f3
CEL is the new system for logging channel events. This was inspired after
facing many problems trying to represent what is possible to happen to a call
in Asterisk using CDR records. For more information on CEL, see the built in
HTML or PDF documentation generated from the files in doc/tex/.
Many thanks to Steve Murphy (murf) and Brian Degenhardt (bmd) for their hard
work developing this code. Also, thanks to Matt Nicholson (mnicholson) and
Sean Bright (seanbright) for their assistance in the final push to get this
code ready for Asterisk trunk.
Review: https://reviewboard.asterisk.org/r/239/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203638 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This merge splits the PRI/BRI signaling logic out of chan_dahdi.c into
sig_pri.c. Functionality in theory should not change (mostly). A few trivial
changes were made in sig_analog with verbose messages and commenting.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203304 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Moved SETCADENCE ioctl call to before call into new analog signal module
to insure that it gets set.
(closes issue #15381)
Reported by: alecdavis
Patches:
fix15381.diff uploaded by dbailey (license 819)
Tested by: dbailey
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203126 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r203115 | russell | 2009-06-25 11:02:16 -0500 (Thu, 25 Jun 2009) | 11 lines
Resolve a crash related to a T.38 reinvite race condition.
This change resolves a crash observed locally during some T.38 testing.
A call was set up using a call file, and when the T.38 reinvite came in,
the channel state was still AST_STATE_DOWN. The reason is explained by
a comment in the code that previously lived in the handling of
AST_STATE_RINGING. This change modifies the logic to handle the same
race condition for any channel state that is not UP.
(closes ABE-1895)
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203116 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r203036 | rmudgett | 2009-06-24 16:01:43 -0500 (Wed, 24 Jun 2009) | 8 lines
Improved chan_dahdi.conf pritimer error checking.
Valid format is: pritimer=timer_name,timer_value
* Fixed segfault if the ',' is missing.
* Completely check the range returned by pri_timer2idx() to prevent
possible access outside array bounds.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203037 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Richard Mudgett
David Vossel
Jeff Peeler
Russell Bryant
Mark Michelson
Kevin P. Fleming
Tilghman Lesher
Matthew Nicholson
Sean Bright
Joshua Colp
Jason Parker
Doug Bailey