The Quectel M95 modem issues a "Call ready" notification when call and
phonebook are ready, so set up a listener for that.
The only way to know when sms is ready is to issue QINITSTAT queries.
Since sms is always ready after call and phonebook, the queries are
initiated after creating call/phonebook.
This adds support for configuring a gpio in udev to control the modem
power.
To enable gpio control, specify OFONO_QUECTEL_GPIO_CHIP and
OFONO_QUECTEL_GPIO_OFFSET in the udev environment, for example:
KERNEL=="ttymxc0", ENV{OFONO_DRIVER}="quectel", \
ENV{OFONO_QUECTEL_GPIO_CHIP}="gpiochip2", \
ENV{OFONO_QUECTEL_GPIO_OFFSET}="26"
Setup GSM 07.10 multiplexing using the kernel n_gsm line discpline
driver, and use the virtual tty devices as Aux and Modem channels.
The driver supports rts/cts on the underlying serial device. This is
enabled with OFONO_QUECTED_RTSCTS udev environment, e.g.:
KERNEL=="ttymxc0", ENV{OFONO_DRIVER}="quectel", \
ENV{OFONO_QUECTEL_RTSCTS}="on"
According to the u-blox AT Commands Manual and my tests
the response prefix of AT+UUSBCONF is "+UUSBCONF:", including
a colon. The colon was missing in the code, causing next step
to parse a number to fail, since a colon is not a number.
In a recent patch vendor family was only set if the device
did not support USBCONF, but that resulted in drivers
being registered the "generic" vendor. That caused
for instance netreg to use incorrect cmer mode and fail
on TOBY-L210.
Trying to set the networking mode to "bridge" mode in the plugin is bogus
because the setting does not apply until after the device has been
reset. Instead, the current setting should be queried.
If a user wants to set the modem networking mode, the setting should be
made outside of ofono.
The gprs-context driver has already been adjusted to query the
networking mode and to set things up accordingly.
Depending on the transport used on the data connection we want either
the "atmodem" (PPP) driver or the "ubloxmodem". For the "ubloxmodem",
we want to pass the model data so this patch wrangles some parameters to
make sure that right driver and right variant data are passed.
ttyACM0 (USB interface 02) is reportedly unreliable (breaking DHCP setup)
so the recommended approach is to use ttyACM2 (USB interface 06)
exclusively.
Some aspects of a device are detectable at runtime, like the USB profile
detection that was added in a patch preceding this one. This patch
switches the driver over from creating a new "vendor id" for each
profile to just setting a flag. This is more easily extensible as we
detect other features of the modem.
The TOBY L2 series of modems presents a number of different
configurations with different throughtput characteristics. These
configurations are packaged up as USB profiles; moreover, changing the
profile actually changes the USB model ID so this is even more like
selecting a different "device" altogether. Nonetheless, all we need to
know is which profile is selected in order to set things up correctly
and this can be queried directly.
This patch adds a call to UUSBCONF for applicable modems in order to
query the USB configuration to find out which profile is active.
This patch adds a call to CGMM into the modem_enable path in order to
establish the specific device model. From this device model string, a
model-specific capabilities structure can be selected.
Many ublox modems can sit on either the USB bus or talk directly to a
UART. The udev plugin mostly takes care of figuring out what ports to
talk to and the protocol is common for all devices after that.
This patch simplifies the setup a bit:
i) There must always be an aux channel for communication with the modem
ii) The aux channel may be found behind the string Aux for USB modems
or Device for serial modems
iii) If the Modem string is set, use it; if not set, assume it's not
available.
Martin Hundebøll
Denis Kenzior
Stefan Herbrechtsmeier
Antara Borwankar
Richard Röjfors
Jonas Bonn
Pičugins Arsenijs