Telit QMI modems can return non-utf-8 characters in plmn-desc.
Observed with LE910-SVG and Verizon. When that happens, libdbus
will abort ofono.
If non-utf-8 characters are detected, use mccmnc string.
LTE modems (observed with Telit LE910 V1) can power on
already registered to a network. In that case, the SS_INFO
change notification will never arrive, and the gprs driver
will never be marked as attached.
To avoid this situation, read SS_INFO at probe time, and if
registered, mark the gprs driver as attached.
This was introduced by the previous patch:
drivers/qmimodem/devinfo.c: In function ‘get_ids_cb’:
drivers/qmimodem/devinfo.c:129:14: error: implicit declaration of function ‘strcmp’ [-Werror=implicit-function-declaration]
if (!str || strcmp(str, "0") == 0) {
Command read_file_info on MC7304 always fails.
Using qmicli or AT command, I am able to read file info.
Qmicli command is:
qmicli -d /dev/cdc-wdm0 --uim-get-file-attributes=0x3f00,0x7fff,0x6fad
[(null)] Successfully got file '/dev/cdc-wdm0' attributes from the UIM:
Card result:
SW1: '0x90'
SW2: '0x00'
File attributes:
File size: 4
File ID: 28589
File type: transparent
Record size: 0
Record count: 0
Read security attributes: (always) (null)
Write security attributes: (single) adm
Increase security attributes: (always) (null)
Deactivate security attributes: (single) adm
Activate security attributes: (single) adm
Raw: 62:17:82:02:41:21:83:02:6F:AD:8A:01:05:8B:...
After a check of parameters sent by qmimodem driver and qmicli,
the only difference is on parameter "Session Information".
Session type sent by qmimodem driver is 'Card on slot 1'.
Session type sent by qmicli command is 'primary-gw-provisioning'.
Changing session type in qmimodem driver fixed problem (on this modem).
Comparing with what is done by qmili command
Some modems do not support AT+CGDATA="PPP",X to enter data state.
Use AT+CGDATA=? to detect these modems and for them use ATD*99***X#
to enter data state.
drivers/rilmodem/stk.c: In function ‘ril_stk_probe’:
drivers/rilmodem/stk.c:210:18: error: ‘data’ is used uninitialized in
this function [-Werror=uninitialized]
struct cb_data *cbd = cb_data_new(stk, NULL, data);
sending RIL_REQUEST_REPORT_STK_SERVICE_IS_RUNNING after
stk atom is created so that modem will inititialize
sim toolkit by sending terminal profile to sim.
During gprs-context driver probe function, check kernel device driver
data format and modem low level data format.
If they are different, align kernel device driver data format on
modem low level data format.
If an error occurs during this process, continue probing without error.
This is inspired by what is done in qmicli and qmi-network (package
libqmi).
Add a way to get and set data format expected by kernel device driver.
This is inspired by what is done in qmicli (package libqmi).
It does not use QMI protocol but a sysfs exported by kernel driver.
To use this feature, kernel version must be equal or more than 4.5.
Network Control Model is a new Communication Device Class
protocol for exchanging Ethernet frames over USB.
NCM is intended to be used with high-speed network
attachments such as HSDPA and LTE data services.
Add a new location-reporting driver for Gemalto Cinterion modems based
on telit implementation + use it in gemalto plugin. It supports
activation of GNSS engine (Request) with command AT^SGPSC. This driver
is tested on PHS8. NMEA frames are accessible on /dev/ttyUSB1.
Retry command QMI_UIM_GET_CARD_STATUS during query_passwd_state if a
temporary error status has been detected.
This happens with a MC7430 modem when query_passwd_state is called just
after PIN is entered.
CGDCONT result parsing fails if first list contains several ranges. For
example with modem Cinterion PHS8:
AT+CGDCONT=?
+CGDCONT: (1-17,101-116),"IP",,,(0),(0-4)
Solution: read first range and jump to second list instead of trying to
close the brackets.
Password state and number of retries asked to modem using
QMI_UIM_GET_CARD_STATUS command rather than remembered after initial
QMI_UIM_GET_CARD_STATUS command.
Add read_imsi feature to qmimodem sim driver.
This is based on DMS service.
On MC7430, this is mandatory to be able to use this driver for GPRS
connection because reading IMSI via EF reads fails.
QMI notification messages handlers are never called on MC7430 without this fix.
- Do not test transaction id before calling notification handler. On MC7430,
notification messages contain a not null transaction id (starts with 1,
increased at each message for a particular client).
- On MC7304 transaction id in notification messages is always 0.
Get current signal strength (type: 0x01), not list of other signals strength
(0x10)
Without this fix:
- I can't get a signal strength on MC7430 because list does not exist
(only one signal strength).
- On MC7304, result is wrong
- useless return at the end of a function
- mixed tabs & spaces for indentation
- over 80 characters for the comment
- line > 80 characters due to access technology conversion. Replaced
with a direct assignment.
drivers/ubloxmodem/netmon.c: In function ‘req_cb_data_unref’:
drivers/ubloxmodem/netmon.c:131:10: error: ‘return’ with a value, in
function returning void [-Werror]
return NULL;
This adds a netmon driver for ublox. The driver support both +COPS and
+CESQ commands to return the previously added ofono netmon types:
RSCP: Received Signal Code Power
ECN0: Received Energy Ratio
RSRQ: Reference Signal Received Quality
RSRP: Reference Signal Received Power
Current revision makes the driver use ref countig when chaining multiple
AT commands.
The U-Blox documentation specifies the following:
* get interface ip and dns from +CGDCONTRDP
* get gw ip and netmask from +UIPADDR
However, different firmware versions have different befaviour:
* On newer firmware, +UIPADDR returns error. But it's possible to configure
gateway ip == ipterface ip (read from CGDCONTRDP).
* On older firmware, we can actually use the commands specified in the
docs.
This patch runs +CGDCONTRDP, configures everything and then tries to run
+UIPADDR. In that works, reconfigures gw ip and netmask.
Adds U-Blox Toby L2 driver for setting the default APN via the
+UCGDFLT command. Currently only IPv4 is supported. APN is
not stored to modem's non-volatile memory. oFono will manage this
default APN via it's config storage.
When receiving an empty default APN, the value is reset.
strtol clamps returned value between INT_MIN and INT_MAX, causing
invalid value (255.255.255.127) being reported for any address
if last octet > 127 when sizeof(long) == 4.
split ril_pin_change_state_cb based on functionality w.r.t.
facility lock, puk and pin. Rename ril_pin_change_state to
more appropriate name ril_set_facility_lock and rename
ril_pin_change_state_cb to ril_enter_sim_pin_cb.