This patch simplifies and cleans up the check_usb_device function a bit
by doing the two following (slightly intertwined) things:
1) The parent "usb_device" is searched for early in this function and this
device will always have the ID_VENDOR_ID and ID_MODEL_ID properties.
As such, we can get them from this device and thereby be certain that
we _always_ have them available.
2) The logic of iterating the vendor_list table is cleaned up. It's
easier to follow and won't be any less efficient.
Telit QMI modems have a problem with the low-power operating modes.
After entering and leaving such a state, UIM service does not return.
The sim card is still marked as powered-down. The QMI interface does
not have a way to power it back on.
To avoid this, keep modems with the "AlwaysOnline" flag online
in the disable-modem and offline-modem procedures.
On E3372 after a GPRS disconnection, modem AT channel (used by PPP) gets
disconnected (G_IO_HUP and G_IO_ERR are detected in received_data
in gatio.c).
After that all connection attempts fail because we are not able to send
any AT commands on modem channel (it is closed).
With this patch, when this behavior is detected, we close gprs context
driver, reopen AT channel and gprs context driver.
This plugin allows to provision gprs-context data based on MCC and MNC.
This is useful when provisioning using mbpi fails (either because you
are using a private APN or because there are multiple internet type context
for your operator in mbpi database).
Config file is STORAGEDIR/provisioning.
Config file should look like that:
[operator:MCC1,MNC1]
internet.AccessPointName=apn1
internet.Username=myUsername
internet.Password=myPassword
internet.AuthenticationMethod=pap
internet.Protocol=ipv6
[operator:MCC2,MNC2]
internet.AccessPointName=apn2
The only mandatory parameter for each operator is internet.AccessPointName.
Parameter description:
internet.AccessPointName: APN
internet.Username: Username
internet.Password: Password
internet.AuthenticationMethod: authentication method.
Possible values are:
- pap
- chap
Default is chap if unset.
internet.Protocol: protocol
Possible values are:
- ip: ipv4
- ipv6
- dual
Default is ip if not set.
All parameters are prefixed with internet to be able to extend this plugin
to other type of contexts (MMS, ...).
At least firmware version 12.00.405 on the UE910-EUR otherwise
closes the AT command port whenever the PPP connection is
dropped, and we'd be left in a funny state.
Telit modems HE910 and UE910 share the same USB
vendor and device IDs (1bc7:0021) but they are
different devices.
HE910 is HSPA Class 14/6 and UE910 is Class 8/6.
Both come in voice-enabled variants.
HE910 also comes in variants with built-in GPS.
Add a new function setup, based on telit, to handle Gemalto P-family
discovery. The setup looks for USB interfaces:
application=/dev/ttyUSB2
gps=/dev/ttyUSB1
modem=/dev/ttyUSB3
Actual cinterion plugin is not compliant with newer Gemalto modems.
Gemalto plugin is based on cinterion with a custom struct to handle the
interfaces Application and Modem.
When the modes are modified with AT^SETPORT="FF;12,1,16", this modem
and pcui will appear using different ids. Update the interfaces
identifier accordingly.
The huawei E3372 exposes two USB tty at /dev/ttyUSB0 and /dev/ttyUSB1
/dev/ttyUSB1 is properly detected as modem.
/dev/ttyUSB0 is the pcui.
lsusb shows 12d1:1506 Huawei Technologies Co., Ltd. Modem/Networkcard
When a modem is being removed, all of the modem's atom watches have
already been cleaned up. Trying to remove it again results in a crash.
Fix by registering a destroy callback which will be notified when the
atomwatch has been removed.
Added 'sofia3gr.ThermalManagement' interface to sofia3gr plugin and
floated 'TransmitPowerThrottling' as an ofono property under that,
to support modem throttling.
'sofia3gr.ThermalManagement'
1.Will be available ONLY if modem throttling is supported in RIL.
This is determined by sending a RIL request during ofono start,
to get current throttling state. If it succeeds, interface is
published otherwise not.
'TransmitPowerThrottling'
1.GetProperties will be allowed both when modem is ON & OFF.
2.GetProperties will be serviced by looking it up from state
information maintained inside ofono. No RIL call will be made.
3.SetProperty will be allowed ONLY when modem is ON.
4.SetProperty request will be forwarded to RIL ONLY if
new state != current state. If RIL request succeeds, state
information will be updated and also, a property change signal
will be emitted.
plugins/gobi.c: In function ‘gobi_pre_sim’:
plugins/gobi.c:431:2: error: ‘sim_driver’ may be used uninitialized in
this function [-Werror=maybe-uninitialized]
ofono_sim_create(modem, 0, sim_driver, data->device);
^
Udevng layer is changed in order to support Sierra QMI modems like
MC73cxx. Identically to Huawei modems, these modems are parsed by
setup_sierra. If QMI interface is detected, the Gobi modem driver is
selected.
Unfortunately, MC73xx chips seem to have a broken QMI UIM interface.
The qmimodem-legacy is so forced in setup function.
At gprs atom 'probe' state, max cid query may fail due to rild
status isn't RADIO_STATUS_ON. It causes gprs atom is removed, gprs
feature is inavailable. Move gprs atom creating to 'post_online'
state to make sure rild status is RADIO_STATUS_ON when query max
cid.
Jonas Bonn
Lukasz Nowak
Christophe Ronco
Piotr Haber
André Draszik
Antara Borwankar
Vincent Cesson
Djalal Harouni
Dragos Tatulea
Kuba Pawlak
Frédéric Dalleau
Ankit Navik
Denis Kenzior
Nishanth V
Rajagopal Aravindan
Caiwen Zhang
Samrat Guha Niyogi
Martin Chaplet
John Ernberg
Kuba Pawlak