TODO:
* Use an event for the report, like SMF_EVT_N4_TIMER?
* Properly set Service identifier in Gy CCR
* SMF: Properly set pkt/octet volumes in Gy CCR
** Update when receiving PFCP Modify Response.
* Figure out best way to require Gy through config file in open5gs-smfd.
* Create a new sess-sm.c which handles smf_sess_t state through
Gx+Gy+PFCP creation, modification and tear down. This way we can do
stuff in parallel, for instance Gx+Gy. It will alsoavoid duplicating
some code paths due to Gy being optional.
Catch Origin-Host during CCA and set it as Destination-Host during
subsequent CCRs. This way we ensure UPDATE/TERMINATION Requests are sent
back explicitly to the same Diameter peer. Moreover, it seems
freediameter relies on this AVP to properly send the message over the
correct SCTP association when several diameter peers are available.
1. UE registered and PDU established.
2. PCF does not receive Heartbeat.
- PCF De-registered state.
- Since PDU is established, SMF should not remove NF instance
3. PCF re-registered.
- HERE, WE NEED TO INCREASE NF REFERENCE COUNT.
Otherwise, NF instance will be removed if PCF is de-registered state
4. UE sends PDU release request.
5. Because SMF knows PCF NF instance, SMF can send PCF delete
As per 3GPP TS 23.401 version 15.12.0, section 5.3.1.2.2
The PDN GW allocates a globally unique /64
IPv6 prefix via Router Advertisement to a given UE.
After the UE has received the Router Advertisement message, it
constructs a full IPv6 address via IPv6 Stateless Address
autoconfiguration in accordance with RFC 4862 using the interface
identifier assigned by PDN GW.
For stateless address autoconfiguration however, the UE can
choose any interface identifier to generate IPv6 addresses, other
than link-local, without involving the network.
And, from section 5.3.1.1, Both EPS network elements and UE shall
support the following mechanisms:
/64 IPv6 prefix allocation via IPv6 Stateless Address
autoconfiguration according to RFC 4862, if IPv6 is
supported.
* [SMF] Gn: Avoid assert crash if no PDP resources available
* [SMF] Gn: Rearrange IE handling order in CreatePDPContextRequest
Let's handle the GTPC remote addr + TEID first, since those should be
used in the CreatePDPContextResponse ideally if available.
Let's then handle parsing of all IEs not related to bearers/UserPlane,
then those missing, and finally do all the IP resource allocation.
* Fix conversion from IPFilterRule to packet filter
As per 3GPP TS 24.008, following Packet filter component type identifier
are not supported on the LTE pre release-11 UEs:
IPv4 local address type
IPv6 remote address/prefix length type
IPv6 local address/prefix length type
And,
IPv6 remote address/prefix length type and
IPv6 local address/prefix length type shall be used when both MS and
Network support Local Address in TFTs.
This commit add logic to omit adding local address in packet filters
for compatibility with pre-release LTE 11 devices. The following parameter
could be used to toggle omit/no to omit behavior.
parameter:
no_ipv4v6_local_addr_in_packet_filter: <true/false>
* Remove logic of supporting pre-release LTE 11 devices in PCRF
* [SMF] typo fixes in commented code
* [SMF] Fix early err return handling UpdatePDPContextRequest
* [SMF] UpdatePDPContext: forward update of remote TEID+IPaddr to UPF
Updating the remote GTP-U IP address and/or TEID on the GGSN is a common
practice, used for instance by an SGSN in a UTRAN network to connect an
HNB(GW) to exchange GTP-U directly with the GGSN. It is also used in
general when doing handovers.
When receiving a UpdatePDPContext with the new address, we need to
forward the update to the UPF so that it takes it into account when
forwarding packets.
This patch only implements updating the information towards the UPF when
GTPv1C is used. Similar approach for GTPv2C (upon receival of Modify
Bearer Request) is still unimplemented.
Related: https://github.com/open5gs/open5gs/issues/1367
In the event we have 2 local IP addresses available for use, put the one
having same IP version in "GGSN Address *" IE, and the one with the
other IP version in "Alternative GGSN Address *" IE.
Same fix was applied recently to CreatePDPContextResponse.
TS 29.060 sections 7.3.4 and 7.3.6 specify the possible cause values for
UpdatePdpContextResponse and DeletePdpContextResponse.
Together with section 8.2, it becomes clear that 'Non-existent' cause
should be sent instead of 'Context not found' one in those cases.
It seems to be actually mandatory in GGSN->SGN directon, though it is
ignored in Release99 upwards. Let's hardcode it to 0 for now, should be
fine in the majority of cases.
In the event we have 2 local IP addresses available for use, put the one
having same IP version in "GGSN Address *" IE, and the one with the
other IP version in "Alternative GGSN Address *" IE.