First of all, it crashes when creating a Dedicated Bearer
on the default Session that is created for the first time.
This behavior should be possible, so the related ASSERT is removed.
Next, the InitialContextRequest is modified
during the Attach Request to include the first Bearer.
Finally, there was an issue where trying to create a Dedicated Bearer
with SGsAP enabled resulted in an InitialContextSetupRequest message
with a PTI of zero. This is because MME initializes the PTI to 0
upon receiving the Create Bearer Request while processing SGsAP.
All of these issues has been fixed.
For bi-directions, the rules are created in the same form as for downlink
as shown below, so to apply them for uplink, we need to swap the rules
according to the interface.
RX : permit out from <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT> to <UE_IP> <UE_PORT>
GX : permit out from <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT> to <UE_IP> <UE_PORT>
PFCP : permit out from <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT> to <UE_IP> <UE_PORT>
RULE : Source <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT> Destination <UE_IP> <UE_PORT>
TFT : Local <UE_IP> <UE_PORT> REMOTE <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT>
RX : permit in from <UE_IP> <UE_PORT> to <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT>
GX : permit out from <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT> to <UE_IP> <UE_PORT>
PFCP : permit out from <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT> to <UE_IP> <UE_PORT>
RULE : Source <UE_IP> <UE_PORT> Destination <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT>
TFT : Local <UE_IP> <UE_PORT> REMOTE <P-CSCF_RTP_IP> <P-CSCF_RTP_PORT>
* [AMF/MME] UEContextReleaseCommand in Integrity (#2786)
Modified not to send UEContextReleaseCommand in Integrity Unprotected
NAS message such like Registration or Service request.
* [AMF/MME] UEContextReleaseCommand after Interity Protected (#2786)
Modified not to send UEContextReleaseCommand in Integrity Unprotected
NAS message such like Registration or Service request.
* Add "subscriber_status" cmd to open5gs-dbctl to set values for
"subscriber_status" and "operator_determined_barring" DB fields.
* Add webui View+Edit for those same fields.
* open5gs-hssd now takes those values into account and submits
Operator-Determined-Barring AVP with DB-retrieved value if
subscriber_status is set to OPERATOR_DETERMINED_BARRING.
For more information, see TS 29.272 section 5.2.2.1.3 and 7.3.30.
o Generate the private key as below.
$ openssl genpkey -algorithm X25519 -out /etc/open5gs/hnet/curve25519-1.key
$ openssl ecparam -name prime256v1 -genkey -conv_form compressed -out /etc/open5gs/hnet/secp256r1-2.key
o The private and public keys can be viewed with the command.
The public key is used when creating the SIM.
$ openssl pkey -in /etc/open5gs/hnet/curve25519-1.key -text
$ openssl ec -in /etc/open5gs/hnet/secp256r1-2.key -conv_form compressed -text
In ausf/udm.yaml
hnet:
o Home network public key identifier(PKI) value : 1
Protection scheme identifier : ECIES scheme profile A
- id: 1
scheme: 1
key: /etc/open5gs/hnet/curve25519-1.key
o Home network public key identifier(PKI) value : 2
Protection scheme identifier : ECIES scheme profile B
- id: 2
scheme: 2
key: /etc/open5gs/hnet/secp256r1-2.key
o Home network public key identifier(PKI) value : 3
Protection scheme identifier : ECIES scheme profile A
- id: 3
scheme: 1
key: /etc/open5gs/hnet/curve25519-1.key
o Home network public key identifier(PKI) value : 4
Protection scheme identifier : ECIES scheme profile B
- id: 4
scheme: 2
key: /etc/open5gs/hnet/secp256r1-2.key
Related to #1779
In the past only GTPv2C was supported, and had the "gtp" generic prefix.
Later on, GTPv1C support was added, and "gtp1" prefix was used.
Let's move GTPv2C specific bits to have "gtp2" prefix too, and leave
"gtp" prefix for generic stuff among different GTP versions.
The network access mode of HSS has been changed to 0 (Packet and Circuit).
Versions of MME prior to v2.4.2 did not use this value. Open5GS set
the attach result of Attach Complete message as it is by looking
at the attach type of the Attach Request message.
Now, if the network access mode of HSS is set to 2 (Only Packet),
this value is affected by MME from v2.4.3. Regardless of the attach type
of the Attach Request, the MME will set EPS Only to the attach result
of Attach Complete.
AMF checks whether it can serve all the S-NSSAI(s) from
the Requested NSSAI present in the Subscribed S-NSSAIs
(potentially using configuration for mapping S-NSSAI values
between HPLMN and Serving PLMN), or all the S-NSSAI(s) marked
as default in the Subscribed S-NSSAIs in the case that
no Requested NSSAI was provided or none of the S-NSSAIs
in the Requested NSSAI are permitted,
i.e. do not match any of the Subscribed S-NSSAIs or not available
at the current UE's Tracking Area (see clause 5.15.3).
- Set the number of UEs in units of AMF/MME instead of gNB/eNB.
- See default value as shown below
Number of UEs per AMF/MME : 4,096
Number of gNB/eNB per AMF/MME : 32