sysmocom_rfdsatt: Actuall "port" over to our target
This patch changes whatever is different bethween the Olimex P103 and the sysmocom rfdsatt board
This commit is contained in:
parent
d53374daa0
commit
3a352025f9
|
@ -46,7 +46,7 @@
|
|||
/** \brief Frequency of the external crystal oscillator. */
|
||||
#define BOOT_CPU_XTAL_SPEED_KHZ (8000)
|
||||
/** \brief Desired system speed. */
|
||||
#define BOOT_CPU_SYSTEM_SPEED_KHZ (72000)
|
||||
#define BOOT_CPU_SYSTEM_SPEED_KHZ (36000)
|
||||
/** \brief Motorola or Intel style byte ordering. */
|
||||
#define BOOT_CPU_BYTE_ORDER_MOTOROLA (0)
|
||||
/** \brief Enable/disable hook function call right before user program start. */
|
||||
|
@ -70,7 +70,7 @@
|
|||
*
|
||||
*/
|
||||
/** \brief Enable/disable CAN transport layer. */
|
||||
#define BOOT_COM_CAN_ENABLE (1)
|
||||
#define BOOT_COM_CAN_ENABLE (0)
|
||||
/** \brief Configure the desired CAN baudrate. */
|
||||
#define BOOT_COM_CAN_BAUDRATE (500000)
|
||||
/** \brief Configure CAN message ID target->host. */
|
||||
|
@ -95,7 +95,7 @@
|
|||
/** \brief Enable/disable UART transport layer. */
|
||||
#define BOOT_COM_RS232_ENABLE (1)
|
||||
/** \brief Configure the desired communication speed. */
|
||||
#define BOOT_COM_RS232_BAUDRATE (57600)
|
||||
#define BOOT_COM_RS232_BAUDRATE (115200)
|
||||
/** \brief Configure number of bytes in the target->host data packet. */
|
||||
#define BOOT_COM_RS232_TX_MAX_DATA (64)
|
||||
/** \brief Configure number of bytes in the host->target data packet. */
|
||||
|
@ -182,7 +182,7 @@
|
|||
* a different checksum location, because this one is added at the end of the
|
||||
* user program's vector table.
|
||||
*/
|
||||
#define BOOT_FLASH_VECTOR_TABLE_CS_OFFSET (0x10c)
|
||||
#define BOOT_FLASH_VECTOR_TABLE_CS_OFFSET (0x150)
|
||||
|
||||
|
||||
/****************************************************************************************
|
||||
|
@ -218,6 +218,8 @@
|
|||
*/
|
||||
#define BOOT_XCP_SEED_KEY_ENABLE (0)
|
||||
|
||||
#define BOOT_FLASH_CUSTOM_LAYOUT_ENABLE (1)
|
||||
|
||||
|
||||
#endif /* BLT_CONF_H */
|
||||
/*********************************** end of blt_conf.h *********************************/
|
||||
|
|
|
@ -80,6 +80,7 @@ blt_bool BackDoorEntryHook(void)
|
|||
****************************************************************************************/
|
||||
blt_bool CpuUserProgramStartHook(void)
|
||||
{
|
||||
#if 0
|
||||
/* additional and optional backdoor entry through the pushbutton on the board. to
|
||||
* force the bootloader to stay active after reset, keep it pressed during reset.
|
||||
*/
|
||||
|
@ -90,6 +91,7 @@ blt_bool CpuUserProgramStartHook(void)
|
|||
*/
|
||||
return BLT_FALSE;
|
||||
}
|
||||
#endif
|
||||
|
||||
/* clean up the LED driver */
|
||||
LedBlinkExit();
|
||||
|
|
|
@ -72,12 +72,12 @@ void LedBlinkTask(void)
|
|||
if (ledOn == BLT_FALSE)
|
||||
{
|
||||
ledOn = BLT_TRUE;
|
||||
LL_GPIO_ResetOutputPin(GPIOC, LL_GPIO_PIN_12);
|
||||
LL_GPIO_ResetOutputPin(GPIOB, LL_GPIO_PIN_15);
|
||||
}
|
||||
else
|
||||
{
|
||||
ledOn = BLT_FALSE;
|
||||
LL_GPIO_SetOutputPin(GPIOC, LL_GPIO_PIN_12);
|
||||
LL_GPIO_SetOutputPin(GPIOB, LL_GPIO_PIN_15);
|
||||
}
|
||||
/* schedule the next blink event */
|
||||
nextBlinkEvent = TimerGet() + ledBlinkIntervalMs;
|
||||
|
@ -94,7 +94,7 @@ void LedBlinkTask(void)
|
|||
void LedBlinkExit(void)
|
||||
{
|
||||
/* turn the LED off */
|
||||
LL_GPIO_SetOutputPin(GPIOC, LL_GPIO_PIN_12);
|
||||
LL_GPIO_SetOutputPin(GPIOB, LL_GPIO_PIN_15);
|
||||
} /*** end of LedBlinkExit ***/
|
||||
|
||||
|
||||
|
|
|
@ -97,14 +97,15 @@ static void Init(void)
|
|||
static void SystemClock_Config(void)
|
||||
{
|
||||
/* Set flash latency. */
|
||||
LL_FLASH_SetLatency(LL_FLASH_LATENCY_2);
|
||||
LL_FLASH_SetLatency(LL_FLASH_LATENCY_1);
|
||||
/* Verify flash latency setting. */
|
||||
if(LL_FLASH_GetLatency() != LL_FLASH_LATENCY_2)
|
||||
if(LL_FLASH_GetLatency() != LL_FLASH_LATENCY_1)
|
||||
{
|
||||
/* Error setting flash latency. */
|
||||
ASSERT_RT(BLT_FALSE);
|
||||
}
|
||||
|
||||
#if 0
|
||||
/* Enable the HSE clock. */
|
||||
LL_RCC_HSE_Enable();
|
||||
|
||||
|
@ -113,9 +114,10 @@ static void SystemClock_Config(void)
|
|||
{
|
||||
;
|
||||
}
|
||||
#endif
|
||||
|
||||
/* Configure and enable the PLL. */
|
||||
LL_RCC_PLL_ConfigDomain_SYS(LL_RCC_PLLSOURCE_HSE_DIV_1, LL_RCC_PLL_MUL_9);
|
||||
LL_RCC_PLL_ConfigDomain_SYS(LL_RCC_PLLSOURCE_HSI_DIV_2, LL_RCC_PLL_MUL_9);
|
||||
LL_RCC_PLL_Enable();
|
||||
|
||||
/* Wait till PLL is ready */
|
||||
|
@ -124,7 +126,7 @@ static void SystemClock_Config(void)
|
|||
;
|
||||
}
|
||||
LL_RCC_SetAHBPrescaler(LL_RCC_SYSCLK_DIV_1);
|
||||
LL_RCC_SetAPB1Prescaler(LL_RCC_APB1_DIV_2);
|
||||
LL_RCC_SetAPB1Prescaler(LL_RCC_APB1_DIV_1);
|
||||
LL_RCC_SetAPB2Prescaler(LL_RCC_APB2_DIV_1);
|
||||
LL_RCC_SetSysClkSource(LL_RCC_SYS_CLKSOURCE_PLL);
|
||||
|
||||
|
@ -172,12 +174,12 @@ void HAL_MspInit(void)
|
|||
#endif
|
||||
|
||||
/* Configure GPIO pin for the LED. */
|
||||
GPIO_InitStruct.Pin = LL_GPIO_PIN_12;
|
||||
GPIO_InitStruct.Pin = LL_GPIO_PIN_15;
|
||||
GPIO_InitStruct.Mode = LL_GPIO_MODE_OUTPUT;
|
||||
GPIO_InitStruct.Speed = LL_GPIO_SPEED_FREQ_LOW;
|
||||
GPIO_InitStruct.OutputType = LL_GPIO_OUTPUT_PUSHPULL;
|
||||
LL_GPIO_Init(GPIOC, &GPIO_InitStruct);
|
||||
LL_GPIO_SetOutputPin(GPIOC, LL_GPIO_PIN_12);
|
||||
LL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
||||
LL_GPIO_SetOutputPin(GPIOB, LL_GPIO_PIN_12);
|
||||
|
||||
/* Configure GPIO pin for (optional) backdoor entry input. */
|
||||
GPIO_InitStruct.Pin = LL_GPIO_PIN_0;
|
||||
|
|
|
@ -28,7 +28,7 @@ SHELL = sh
|
|||
#|--------------------------------------------------------------------------------------|
|
||||
#| Configure project name |
|
||||
#|--------------------------------------------------------------------------------------|
|
||||
PROJ_NAME=openblt_olimex_stm32p103
|
||||
PROJ_NAME=openblt_sysmocom_rfdsatt
|
||||
|
||||
|
||||
#|--------------------------------------------------------------------------------------|
|
||||
|
@ -140,6 +140,7 @@ all: $(BIN_PATH)/$(PROJ_NAME).srec
|
|||
$(BIN_PATH)/$(PROJ_NAME).srec : $(BIN_PATH)/$(PROJ_NAME).elf
|
||||
@$(OC) $< $(OFLAGS) $@
|
||||
@$(OD) $(ODFLAGS) $< > $(BIN_PATH)/$(PROJ_NAME).map
|
||||
@$(OC) -O binary $^ $(BIN_PATH)/$(PROJ_NAME).bin
|
||||
@echo +++ Summary of memory consumption:
|
||||
@$(SZ) $(SZFLAGS) $<
|
||||
@echo +++ Build complete [$(notdir $@)]
|
||||
|
|
Loading…
Reference in New Issue