diff --git a/Host/Source/LibOpenBLT/xcploader.h b/Host/Source/LibOpenBLT/xcploader.h
index 52261f02..4be29766 100644
--- a/Host/Source/LibOpenBLT/xcploader.h
+++ b/Host/Source/LibOpenBLT/xcploader.h
@@ -66,13 +66,13 @@ typedef struct t_xcp_transport_packet
/** \brief XCP transport layer. */
typedef struct t_xcp_transport
{
- /** \brief Initialization of the XCP transpor layer. */
+ /** \brief Initialization of the XCP transport layer. */
void (*Init) (void const * settings);
- /** \brief Termination the XCP transpor layer. */
+ /** \brief Termination the XCP transport layer. */
void (*Terminate) (void);
- /** \brief Connects the XCP transpor layer. */
+ /** \brief Connects the XCP transport layer. */
bool (*Connect) (void);
- /** \brief Disconnects the XCP transpor layer. */
+ /** \brief Disconnects the XCP transport layer. */
void (*Disconnect) (void);
/** \brief Sends an XCP packet and waits for the response to come back. */
bool (*SendPacket) (tXcpTransportPacket const * txPacket,
@@ -86,11 +86,11 @@ typedef struct t_xcp_loader_settings
uint16_t timeoutT1;
/** \brief Start programming timeout in milliseconds. */
uint16_t timeoutT3;
- /** \brief Erase memory timeout in milliseonds. */
+ /** \brief Erase memory timeout in milliseconds. */
uint16_t timeoutT4;
- /** \brief Program memory and reset timeout in milliseonds. */
+ /** \brief Program memory and reset timeout in milliseconds. */
uint16_t timeoutT5;
- /** \brief Busy wait timer timeout in milliseonds. */
+ /** \brief Busy wait timer timeout in milliseconds. */
uint16_t timeoutT7;
/** \brief Connection mode used in the XCP connect command. */
uint8_t connectMode;
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.cproject b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.cproject
new file mode 100644
index 00000000..4ceb4efc
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.cproject
@@ -0,0 +1,135 @@
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.project b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.project
new file mode 100644
index 00000000..9744ab44
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.project
@@ -0,0 +1,59 @@
+
+
+ Boot
+
+
+
+
+
+ org.eclipse.cdt.managedbuilder.core.genmakebuilder
+ clean,full,incremental,
+
+
+
+
+ org.eclipse.cdt.managedbuilder.core.ScannerConfigBuilder
+ full,incremental,
+
+
+
+
+
+ org.eclipse.cdt.core.cnature
+ org.eclipse.cdt.managedbuilder.core.managedBuildNature
+ org.eclipse.cdt.managedbuilder.core.ScannerConfigNature
+
+
+
+ core
+ 2
+ OPENBLT_ROOT
+
+
+
+
+ 1528381552500
+ core
+ 9
+
+ org.eclipse.ui.ide.multiFilter
+ 1.0-name-matches-false-false-ARMCM3_STM32F1
+
+
+
+ 1528381562828
+ core/ARMCM3_STM32F1
+ 9
+
+ org.eclipse.ui.ide.multiFilter
+ 1.0-name-matches-false-false-GCC
+
+
+
+
+
+ OPENBLT_ROOT
+ $%7BPARENT-3-PROJECT_LOC%7D/Source
+
+
+
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/com.atollic.truestudio.debug.hardware_device.prefs b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/com.atollic.truestudio.debug.hardware_device.prefs
new file mode 100644
index 00000000..9f4e4c5b
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/com.atollic.truestudio.debug.hardware_device.prefs
@@ -0,0 +1,11 @@
+BOARD=None
+CODE_LOCATION=FLASH
+ENDIAN=Little-endian
+MCU=STM32F103RB
+MCU_VENDOR=STMicroelectronics
+MODEL=Pro
+PROBE=ST-LINK
+PROJECT_FORMAT_VERSION=2
+TARGET=STM32
+VERSION=9.0.1
+eclipse.preferences.version=1
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/language.settings.xml b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/language.settings.xml
new file mode 100644
index 00000000..79a37d2b
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/language.settings.xml
@@ -0,0 +1,13 @@
+
+
+
+
+
+
+
+
+
+
+
+
+
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.core.prefs b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.core.prefs
new file mode 100644
index 00000000..f6753e14
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.core.prefs
@@ -0,0 +1,164 @@
+eclipse.preferences.version=1
+org.eclipse.cdt.core.formatter.alignment_for_arguments_in_method_invocation=16
+org.eclipse.cdt.core.formatter.alignment_for_assignment=16
+org.eclipse.cdt.core.formatter.alignment_for_base_clause_in_type_declaration=80
+org.eclipse.cdt.core.formatter.alignment_for_binary_expression=16
+org.eclipse.cdt.core.formatter.alignment_for_compact_if=16
+org.eclipse.cdt.core.formatter.alignment_for_conditional_expression=34
+org.eclipse.cdt.core.formatter.alignment_for_conditional_expression_chain=18
+org.eclipse.cdt.core.formatter.alignment_for_constructor_initializer_list=0
+org.eclipse.cdt.core.formatter.alignment_for_declarator_list=16
+org.eclipse.cdt.core.formatter.alignment_for_enumerator_list=48
+org.eclipse.cdt.core.formatter.alignment_for_expression_list=0
+org.eclipse.cdt.core.formatter.alignment_for_expressions_in_array_initializer=16
+org.eclipse.cdt.core.formatter.alignment_for_member_access=0
+org.eclipse.cdt.core.formatter.alignment_for_overloaded_left_shift_chain=16
+org.eclipse.cdt.core.formatter.alignment_for_parameters_in_method_declaration=16
+org.eclipse.cdt.core.formatter.alignment_for_throws_clause_in_method_declaration=16
+org.eclipse.cdt.core.formatter.brace_position_for_array_initializer=next_line
+org.eclipse.cdt.core.formatter.brace_position_for_block=next_line
+org.eclipse.cdt.core.formatter.brace_position_for_block_in_case=next_line
+org.eclipse.cdt.core.formatter.brace_position_for_method_declaration=next_line
+org.eclipse.cdt.core.formatter.brace_position_for_namespace_declaration=next_line
+org.eclipse.cdt.core.formatter.brace_position_for_switch=next_line
+org.eclipse.cdt.core.formatter.brace_position_for_type_declaration=next_line
+org.eclipse.cdt.core.formatter.comment.line_up_line_comment_in_blocks_on_first_column=false
+org.eclipse.cdt.core.formatter.comment.min_distance_between_code_and_line_comment=1
+org.eclipse.cdt.core.formatter.comment.never_indent_line_comments_on_first_column=true
+org.eclipse.cdt.core.formatter.comment.preserve_white_space_between_code_and_line_comments=true
+org.eclipse.cdt.core.formatter.compact_else_if=true
+org.eclipse.cdt.core.formatter.continuation_indentation=2
+org.eclipse.cdt.core.formatter.continuation_indentation_for_array_initializer=2
+org.eclipse.cdt.core.formatter.format_guardian_clause_on_one_line=false
+org.eclipse.cdt.core.formatter.indent_access_specifier_compare_to_type_header=false
+org.eclipse.cdt.core.formatter.indent_access_specifier_extra_spaces=0
+org.eclipse.cdt.core.formatter.indent_body_declarations_compare_to_access_specifier=true
+org.eclipse.cdt.core.formatter.indent_body_declarations_compare_to_namespace_header=false
+org.eclipse.cdt.core.formatter.indent_breaks_compare_to_cases=true
+org.eclipse.cdt.core.formatter.indent_declaration_compare_to_template_header=false
+org.eclipse.cdt.core.formatter.indent_empty_lines=false
+org.eclipse.cdt.core.formatter.indent_statements_compare_to_block=true
+org.eclipse.cdt.core.formatter.indent_statements_compare_to_body=true
+org.eclipse.cdt.core.formatter.indent_switchstatements_compare_to_cases=true
+org.eclipse.cdt.core.formatter.indent_switchstatements_compare_to_switch=false
+org.eclipse.cdt.core.formatter.indentation.size=2
+org.eclipse.cdt.core.formatter.insert_new_line_after_opening_brace_in_array_initializer=do not insert
+org.eclipse.cdt.core.formatter.insert_new_line_after_template_declaration=do not insert
+org.eclipse.cdt.core.formatter.insert_new_line_at_end_of_file_if_missing=do not insert
+org.eclipse.cdt.core.formatter.insert_new_line_before_catch_in_try_statement=do not insert
+org.eclipse.cdt.core.formatter.insert_new_line_before_closing_brace_in_array_initializer=do not insert
+org.eclipse.cdt.core.formatter.insert_new_line_before_colon_in_constructor_initializer_list=do not insert
+org.eclipse.cdt.core.formatter.insert_new_line_before_else_in_if_statement=insert
+org.eclipse.cdt.core.formatter.insert_new_line_before_identifier_in_function_declaration=do not insert
+org.eclipse.cdt.core.formatter.insert_new_line_before_while_in_do_statement=do not insert
+org.eclipse.cdt.core.formatter.insert_new_line_in_empty_block=insert
+org.eclipse.cdt.core.formatter.insert_space_after_assignment_operator=insert
+org.eclipse.cdt.core.formatter.insert_space_after_binary_operator=insert
+org.eclipse.cdt.core.formatter.insert_space_after_closing_angle_bracket_in_template_arguments=insert
+org.eclipse.cdt.core.formatter.insert_space_after_closing_angle_bracket_in_template_parameters=insert
+org.eclipse.cdt.core.formatter.insert_space_after_closing_brace_in_block=insert
+org.eclipse.cdt.core.formatter.insert_space_after_closing_paren_in_cast=insert
+org.eclipse.cdt.core.formatter.insert_space_after_colon_in_base_clause=insert
+org.eclipse.cdt.core.formatter.insert_space_after_colon_in_case=insert
+org.eclipse.cdt.core.formatter.insert_space_after_colon_in_conditional=insert
+org.eclipse.cdt.core.formatter.insert_space_after_colon_in_labeled_statement=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_array_initializer=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_base_types=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_declarator_list=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_enum_declarations=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_expression_list=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_method_declaration_parameters=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_method_declaration_throws=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_method_invocation_arguments=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_template_arguments=insert
+org.eclipse.cdt.core.formatter.insert_space_after_comma_in_template_parameters=insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_angle_bracket_in_template_arguments=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_angle_bracket_in_template_parameters=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_brace_in_array_initializer=insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_bracket=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_cast=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_catch=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_exception_specification=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_for=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_if=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_method_declaration=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_method_invocation=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_parenthesized_expression=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_switch=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_opening_paren_in_while=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_postfix_operator=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_prefix_operator=do not insert
+org.eclipse.cdt.core.formatter.insert_space_after_question_in_conditional=insert
+org.eclipse.cdt.core.formatter.insert_space_after_semicolon_in_for=insert
+org.eclipse.cdt.core.formatter.insert_space_after_unary_operator=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_assignment_operator=insert
+org.eclipse.cdt.core.formatter.insert_space_before_binary_operator=insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_angle_bracket_in_template_arguments=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_angle_bracket_in_template_parameters=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_brace_in_array_initializer=insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_bracket=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_cast=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_catch=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_exception_specification=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_for=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_if=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_method_declaration=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_method_invocation=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_parenthesized_expression=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_switch=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_closing_paren_in_while=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_colon_in_base_clause=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_colon_in_case=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_colon_in_conditional=insert
+org.eclipse.cdt.core.formatter.insert_space_before_colon_in_default=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_colon_in_labeled_statement=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_array_initializer=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_base_types=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_declarator_list=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_enum_declarations=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_expression_list=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_method_declaration_parameters=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_method_declaration_throws=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_method_invocation_arguments=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_template_arguments=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_comma_in_template_parameters=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_angle_bracket_in_template_arguments=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_angle_bracket_in_template_parameters=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_brace_in_array_initializer=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_brace_in_block=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_brace_in_method_declaration=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_brace_in_namespace_declaration=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_brace_in_switch=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_brace_in_type_declaration=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_bracket=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_catch=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_exception_specification=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_for=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_if=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_method_declaration=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_method_invocation=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_parenthesized_expression=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_switch=insert
+org.eclipse.cdt.core.formatter.insert_space_before_opening_paren_in_while=insert
+org.eclipse.cdt.core.formatter.insert_space_before_postfix_operator=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_prefix_operator=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_question_in_conditional=insert
+org.eclipse.cdt.core.formatter.insert_space_before_semicolon=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_semicolon_in_for=do not insert
+org.eclipse.cdt.core.formatter.insert_space_before_unary_operator=do not insert
+org.eclipse.cdt.core.formatter.insert_space_between_empty_braces_in_array_initializer=do not insert
+org.eclipse.cdt.core.formatter.insert_space_between_empty_brackets=do not insert
+org.eclipse.cdt.core.formatter.insert_space_between_empty_parens_in_exception_specification=do not insert
+org.eclipse.cdt.core.formatter.insert_space_between_empty_parens_in_method_declaration=do not insert
+org.eclipse.cdt.core.formatter.insert_space_between_empty_parens_in_method_invocation=do not insert
+org.eclipse.cdt.core.formatter.join_wrapped_lines=true
+org.eclipse.cdt.core.formatter.keep_else_statement_on_same_line=false
+org.eclipse.cdt.core.formatter.keep_empty_array_initializer_on_one_line=false
+org.eclipse.cdt.core.formatter.keep_imple_if_on_one_line=false
+org.eclipse.cdt.core.formatter.keep_then_statement_on_same_line=false
+org.eclipse.cdt.core.formatter.lineSplit=89
+org.eclipse.cdt.core.formatter.number_of_empty_lines_to_preserve=1
+org.eclipse.cdt.core.formatter.put_empty_statement_on_new_line=true
+org.eclipse.cdt.core.formatter.tabulation.char=space
+org.eclipse.cdt.core.formatter.tabulation.size=2
+org.eclipse.cdt.core.formatter.use_tabs_only_for_leading_indentations=false
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.managedbuilder.core.prefs b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.managedbuilder.core.prefs
new file mode 100644
index 00000000..7e39a4f1
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.managedbuilder.core.prefs
@@ -0,0 +1,11 @@
+eclipse.preferences.version=1
+environment/buildEnvironmentInclude/com.atollic.truestudio.exe.debug.908691675/CPATH/delimiter=\:
+environment/buildEnvironmentInclude/com.atollic.truestudio.exe.debug.908691675/CPATH/operation=remove
+environment/buildEnvironmentInclude/com.atollic.truestudio.exe.debug.908691675/C_INCLUDE_PATH/delimiter=\:
+environment/buildEnvironmentInclude/com.atollic.truestudio.exe.debug.908691675/C_INCLUDE_PATH/operation=remove
+environment/buildEnvironmentInclude/com.atollic.truestudio.exe.debug.908691675/append=true
+environment/buildEnvironmentInclude/com.atollic.truestudio.exe.debug.908691675/appendContributed=true
+environment/buildEnvironmentLibrary/com.atollic.truestudio.exe.debug.908691675/LIBRARY_PATH/delimiter=\:
+environment/buildEnvironmentLibrary/com.atollic.truestudio.exe.debug.908691675/LIBRARY_PATH/operation=remove
+environment/buildEnvironmentLibrary/com.atollic.truestudio.exe.debug.908691675/append=true
+environment/buildEnvironmentLibrary/com.atollic.truestudio.exe.debug.908691675/appendContributed=true
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.ui.prefs b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.ui.prefs
new file mode 100644
index 00000000..e1896bba
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/.settings/org.eclipse.cdt.ui.prefs
@@ -0,0 +1,3 @@
+eclipse.preferences.version=1
+formatter_profile=_Feaser
+formatter_settings_version=1
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/Debug/openblt_nucleo_stm32f103rb.elf b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/Debug/openblt_nucleo_stm32f103rb.elf
new file mode 100755
index 00000000..74901ef6
Binary files /dev/null and b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/Debug/openblt_nucleo_stm32f103rb.elf differ
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/Debug/openblt_nucleo_stm32f103rb.srec b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/Debug/openblt_nucleo_stm32f103rb.srec
new file mode 100755
index 00000000..c950d062
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/Debug/openblt_nucleo_stm32f103rb.srec
@@ -0,0 +1,324 @@
+S02200006F70656E626C745F6E75636C656F5F73746D33326631303372622E7372656343
+S3150800000000500020351200088512000885120008E5
+S3150800001085120008851200088512000800000000F5
+S315080000200000000000000000000000008512000823
+S3150800003085120008000000008512000885120008D5
+S315080000408512000885120008851200088512000826
+S315080000508512000885120008851200088512000816
+S315080000608512000885120008851200088512000806
+S3150800007085120008851200088512000885120008F6
+S3150800008085120008851200088512000885120008E6
+S3150800009085120008851200088512000885120008D6
+S315080000A085120008851200088512000885120008C6
+S315080000B085120008851200088512000885120008B6
+S315080000C085120008851200088512000885120008A6
+S315080000D08512000885120008851200088512000896
+S315080000E08512000885120008851200080000000025
+S315080000F000000000000000000000000000000000F2
+S3110800010000000000000000005FF808F195
+S3150800010C10B5054C237833B9044B13B10448AFF337
+S3150800011C00800123237010BD04000020000000009D
+S3150800012CD012000808B5034B1BB103490348AFF3BB
+S3150800013C008008BD0000000008000020D01200084E
+S3150800014C72B6704762B6704708B5FFF7F9FF08BD77
+S3150800015C10B500F0B3FA00B910BD00F053FE002834
+S3150800016CFAD000F01FFC00F0BDFA00F0ABFA20F054
+S3150800017C604020F07F00044B186000F0A3FA446836
+S3150800018CFFF7E0FFA047E7E708ED00E070B508E0E9
+S3150800019C461C4D1C0B78037000F034FC304629467F
+S315080001AC2246531E9CB2002AF2D170BD044B054A56
+S315080001BC5A6002F188325A603422DA60704700BFFE
+S315080001CC0020024023016745024A136943F0800365
+S315080001DC136170470020024038B50546002401E03B
+S315080001EC0134E4B20E2C15D800F00CFC04EB4402D6
+S315080001FC9300094AD358AB42F2D804EB4402910057
+S3150800020C054A0A44526813449D42E9D2024B0B44F0
+S3150800021C187A38BDFF2038BDE812000838B50546EF
+S3150800022C00240E2C10D800F0EDFB04EB44039A00C6
+S3150800023C074B13441B7AAB4202D00134E4B2F0E705
+S3150800024C1346034AD05838BD4FF0FF3038BD00BFAF
+S3150800025CE812000838B5054600240E2C10D800F014
+S3150800026CD1FB04EB44039A00064B13441B7AAB42AE
+S3150800027C02D00134E4B2F0E7024B1344586838BD97
+S3150800028C002038BDE812000808B5C1F3080353B9B5
+S3150800029C0368994209D040F8041B4FF40072FFF723
+S315080002AC75FF012008BD002008BD012008BD00000F
+S315080002BC2DE9F84F81460068FFF78EFFFF2856D0C8
+S315080002CCFFF774FF2B4BDB6813F0010F08D1294A93
+S315080002DC136943F00103136100254FF0010A09E085
+S315080002ECFFF772FF4FF0000A3EE058F807309E42BF
+S315080002FC31D101357F2D30D8D9F80080AF0008EB05
+S3150800030C070B09EB07035E68B3B228F8253000F033
+S3150800031C11FA441D174BDB6813F0010F07D000F0D8
+S3150800032C71FB00F007FA8442F4D24FF0000A330C42
+S3150800033CABF8023000F0FEF9441D0E4BDB6813F0E7
+S3150800034C010FD2D000F05EFB00F0F4F98442F4D22F
+S3150800035C4FF0000AC9E74FF0000A064A136923F062
+S3150800036C01031361FFF730FF5046BDE8F88F4FF0D5
+S3150800037C000AF9E70020024038B50D460B4B9842A7
+S3150800038C08D004460A4B994206D0FFF791FF20B9CC
+S3150800039C002407E0074C00E0044C29462046FFF7EA
+S315080003AC73FF08B1204638BD0024FBE72402002061
+S315080003BC00200008200000202DE9F04106460C46D6
+S315080003CC17461D4621F4FF7828F001080368B3F197
+S315080003DCFF3F0DD03368984505D041463046FFF7A8
+S315080003ECCBFF064628B33368E41A344404340CE0CD
+S315080003FC4146FFF749FF03460028EBD116E017F8EC
+S3150800040C013B04F8013B013D0FD000F0FBFA331D0C
+S3150800041CE31AB3F5007FF2D308F500713046FFF7FF
+S3150800042CABFF064638B1041DE9E701231846BDE8BB
+S3150800043CF0810023FAE70023F8E700002DE9F041E4
+S3150800044C884251D8002853D00F2901D900264CE0F0
+S3150800045C0D460446FFF7AAFE264BDB6813F0010F80
+S3150800046C19D1244A136943F0020313612046FFF796
+S3150800047CD5FE80462846FFF7D1FE07462846FFF7E5
+S3150800048CE9FE0744013FA7EB08070137C7F38F2797
+S3150800049C0126002505E0FFF797FE002625E0013525
+S315080004ACADB2BD4218D208EB8522124B5A611A69B5
+S315080004BC42F040021A6100F03DF900F164040D4B5C
+S315080004CCDB6813F0010FEAD000F09CFA00F032F961
+S315080004DC8442F4D20026E2E7064A136923F00203A3
+S315080004EC1361FFF771FE00E000263046BDE8F08187
+S315080004FC0026FAE7002002404FF0FF33024A136049
+S3150800050C024A1360704700BF200000202402002016
+S3150800051C70B54B1E154C241AA34201D9002070BD88
+S3150800052C16460D460446FFF757FEFF281AD028191B
+S3150800053C0138FFF751FEFF2816D024F4FF7323F079
+S3150800054C01030B4A934206D02B46324621460948EC
+S3150800055CFFF732FF70BD2B46324621460648FFF799
+S3150800056C2BFF70BD002070BD002070BDFFFF010879
+S3150800057C0020000820000020240200204A1E0E4BF2
+S3150800058C1B1A9A4201D90020704770B50C460546CD
+S3150800059CFFF722FE064660190138FFF71DFEFF2EEF
+S315080005AC06D0FF2806D001463046FFF747FF70BD38
+S315080005BC002070BD002070BDFFFF0108104B1B68A2
+S315080005CCB3F1FF3F1AD000B583B00D4A5368916852
+S315080005DC0B44D1680B4411690B4451690B4491695E
+S315080005EC0B44D26913445B4202AA42F8043D042127
+S315080005FC0448FFF78DFF03B05DF804FB0120704734
+S3150800060C240200200C2100080D4B1B680D4A1268A9
+S3150800061C13440D4A126813440C4A126813440C4AC4
+S3150800062C126813440B4A126813440B4A1268134493
+S3150800063C0A4A1268D34201D000207047012070473D
+S3150800064C0020000804200008082000080C200008D8
+S3150800065C1020000814200008182000080C21000897
+S3150800066C08B50C4B1B68B3F1FF3F04D00948FFF7DC
+S3150800067C1FFE034650B1084B1B68B3F1FF3F07D06A
+S3150800068C0548FFF715FE034600B10123184608BDB9
+S3150800069C0123FBE7240200202000002000487047B5
+S315080006AC0020000808B5FFF727FF08BD08B5FFF7B7
+S315080006BC2FFF08BD08B5FFF761FF08BD08B5FFF7A2
+S315080006CCA3FF08BD08B5FFF7E9FF08BD08B5FFF796
+S315080006DC75FF034608B9184608BDFFF7C1FF034660
+S315080006ECF9E700000022014B1A60704710E000E0A1
+S315080006FC08B5FFF7F7FF054B054A5A6000229A60C2
+S3150800070C05211960034B1A6008BD00BF10E000E014
+S3150800071C3F19010028040020044B1B6813F4803F82
+S3150800072C03D0034A136801331360704710E000E0E6
+S3150800073C2804002008B5FFF7EFFF014B186808BD21
+S3150800074C28040020054B1B8813F0200F04D0034BFC
+S3150800075C9B880370012070470020704700440040B6
+S3150800076C0E4B1B8813F0800F01D10020704710B573
+S3150800077C80B20A4B9880FFF7DDFF00F10A04074B9D
+S3150800078C1B8813F0800F07D100F03CF9FFF7D2FF56
+S3150800079C8442F4D2002010BD012010BD0044004054
+S315080007AC084B00221A819A811A829A821A8340F27D
+S315080007BC71221A819A8992B242F4005242F00C02C2
+S315080007CC9A8170470044004070B506460D4640298C
+S315080007DC0AD82846FFF7C4FF012803D093210E48F0
+S315080007EC00F072F8002406E08F210B4800F06CF834
+S315080007FCEFE70134A4B2ABB29C420BD200F002F97B
+S3150800080C305DFFF7ADFF0128F3D09C21024800F0BC
+S3150800081C5BF8EEE770BD00BF9C13000870B5254B5E
+S3150800082C1C78BCB92448FFF78DFF012801D0204657
+S3150800083C70BD214B1B78013BDBB23F2BF7D8FFF77A
+S3150800084C79FF1E4B186000221D4B1A700122194B9A
+S3150800085C1A70ECE706460D46194B1B7801331648F9
+S3150800086C1844FFF76FFF044601280AD0FFF762FF0A
+S3150800087C124B1B686433984219D900240D4B1C7013
+S3150800088CD5E70F4B1A780132D2B21A700A4B1B787D
+S3150800089C9A4201D00024CAE70A493046FFF776FC8B
+S315080008AC0022044B1A70064B1B782B70BFE70024EA
+S315080008BCBDE700BF6D0400202C0400207004002046
+S315080008CC6E0400202D04002008B500F09BF8FCE708
+S315080008DC08B500F08FF8012803D0094B1B78012BBB
+S315080008EC00D008BDFFF726FF064B1B6803F5FA7305
+S315080008FC9842F6D30022024B1A70FFF729FCF0E750
+S3150800090C740400207804002008B50122044B1A70E0
+S3150800091CFFF710FF034B1860FFF7DAFF08BD00BF9F
+S3150800092C740400207804002008B5FFF70DFC00F0CD
+S3150800093C65F8FFF7DDFEFFF7B5FE00F00DF8FFF7DB
+S3150800094CE3FF08BD08B500F05DF8FFF7E5FE00F01B
+S3150800095C0FF8FFF7BDFF08BD08B500F0C1F9FFF7A2
+S3150800096C1FFF0022014B1A7008BD00BF00000020B3
+S3150800097C00B583B00DF107010848FFF74FFF0128B2
+S3150800098C02D003B05DF804FB0022054B1A709DF8E3
+S3150800099C0710024800F0C4F9F3E700BF7C040020F6
+S315080009AC000000207047000008B5054B1B7813B1F2
+S315080009BC00F0AEF908BDC9B2FFF706FFF8E700BFAD
+S315080009CC00000020044B1B78013B022B01D9402068
+S315080009DC70470020704700BF00000020044B1B78AE
+S315080009EC013B022B01D9402070470020704700BFFD
+S315080009FC0000002008B500F081F908BD08B500F024
+S31508000A0C0FFA08BD08B500F010FA08BD0022014B14
+S31508000A1C5A707047BC040020034BFE22DA7018711A
+S31508000A2C0222A3F844207047BC04002010B5054CDC
+S31508000A3C00232370FFF7EAFFFF23E3700123A4F8D2
+S31508000A4C443010BDBC040020064BFF22DA7000228D
+S31508000A5C1A71597859719A71DA711A720622A3F8B1
+S31508000A6C44207047BC04002008B50020FFF7D4FFCB
+S31508000A7C08BD0000074BFF22DA70074A9A64002269
+S31508000A8C1A715A719A710722C3F807200822A3F81B
+S31508000A9C44207047BC040020C8130008044BFF22EE
+S31508000AACDA7042689A640122A3F84420704700BFA2
+S31508000ABCBC04002008B53120FFF7AEFF08BD0000C6
+S31508000ACC38B5084CFF23E370002525716571FFF7CF
+S31508000ADC79FFA071E571257265720723A4F8443075
+S31508000AEC38BD00BFBC04002038B5FFF78FFF0E4C8D
+S31508000AFC01252570FF23E3701023237100236371EE
+S31508000B0CFFF760FFA071FFF769FFE071FFF766FF5B
+S31508000B1CC0F3072020726572A5720823A4F8443026
+S31508000B2CFFF7C0FD38BD00BFBC04002038B505462C
+S31508000B3C4478FFF747FF0138844210DC0A4C6A7880
+S31508000B4CA16C201DFFF722FBFF23E3706A78A36CC8
+S31508000B5C1344A3646B780133A4F8443038BD2220BF
+S31508000B6CFFF75AFF38BD00BFBC04002038B5044651
+S31508000B7C4578FFF727FF0138854211DC61680A4D75
+S31508000B8CA9646278281DFFF701FBFF23EB706278D6
+S31508000B9CAB6C1344AB6463780133A5F8443038BDA9
+S31508000BAC2220FFF739FF38BDBC040020F8B50546EE
+S31508000BBC1746002406E015F8013B1C44E4B2FFF77F
+S31508000BCC21FF31464E1E0029F5D13C600120F8BDA7
+S31508000BDC10B5084CFF23E370E21D4168A06CFFF7C3
+S31508000BECE5FF207100236371A3710823A4F8443030
+S31508000BFC10BD00BFBC04002038B505460D4B9C6CD7
+S31508000C0CFFF7E0FE6A1C411E2046FFF74FFD60B158
+S31508000C1C084CFF23E370FFF7D5FE0138A36C034499
+S31508000C2CA3640123A4F8443038BD3120FFF7F4FE41
+S31508000C3C38BD00BFBC04002038B504464578FFF71C
+S31508000C4CC1FE023885420EDC114BFF22DA700122F6
+S31508000C5CA3F84420617851B9FFF738FD90B93120D3
+S31508000C6CFFF7DAFE38BD2220FFF7D6FE38BDA21CE8
+S31508000C7C074B986CFFF71AFD28B16178044A936CF8
+S31508000C8C0B44936438BD3120FFF7C6FE38BD00BF50
+S31508000C9CBC04002008B54168074B986CFFF70AFDA1
+S31508000CAC30B1054BFF22DA700122A3F8442008BDA7
+S31508000CBC3120FFF7B1FE08BDBC04002008B5FFF7CC
+S31508000CCC47FA034BFF22DA700122A3F8442008BD29
+S31508000CDCBC04002008B589B2FFF766FE08BD000003
+S31508000CEC054B00221A709A6483F84320A3F8442013
+S31508000CFC9A705A70704700BFBC040020034B1B78CF
+S31508000D0C0BB1012070470020704700BFBC040020BF
+S31508000D1C0022024B83F84320704700BFBC04002016
+S31508000D2C08B50378FF2B04D0354A1278012A14D05B
+S31508000D3C08BDFFF7D9FE324B93F84330012B5AD036
+S31508000D4C2F4BB3F944100029F2DD1846012380F81D
+S31508000D5C43300330FFF7BEFFEAE7C93B352B46D8CD
+S31508000D6CDFE803F03345454245453F363C394545B2
+S31508000D7C4545454545454545454545454545454509
+S31508000D8C4545454545454545454545454545241E41
+S31508000D9C1B2145454527452A2D30FFF7C7FECAE7CF
+S31508000DACFFF7E4FEC7E7FFF779FEC4E7FFF710FF86
+S31508000DBCC1E7FFF75FFEBEE7FFF756FEBBE7FFF797
+S31508000DCC43FEB8E7FFF732FEB5E7FFF715FFB2E7C4
+S31508000DDCFFF732FFAFE7FFF773FEACE7FFF75AFFF3
+S31508000DECA9E7FFF76BFFA6E7FFF764FEA3E720204A
+S31508000DFCFFF712FE9FE71020FFF70EFEA0E700BFD5
+S31508000E0CBC04002008B500F045F84FF4005103481F
+S31508000E1C00F025F900B1012008BD00BF0010014003
+S31508000E2C08B5642000F006F808BD08B500F008F807
+S31508000E3C08BD0000014B1880704700BF080500204C
+S31508000E4C08B5FFF777FC0F4B1B68984210D30E4B6F
+S31508000E5C1B7873B901220C4B1A7020210B4800F031
+S31508000E6C05F9FFF767FC0A4B1B881844054B1860F5
+S31508000E7C08BD0022044B1A702021044800F0F8F82B
+S31508000E8CEFE700BF0C0500200A050020000801400A
+S31508000E9C0805002008B52021014800F0E9F808BD2E
+S31508000EAC0008014082B00023019300932C4A136872
+S31508000EBC43F4803313602A4B1B6803F40033009306
+S31508000ECC019B01330193009B1BB9019BB3F5A06FE2
+S31508000EDCF1D1234B1B6813F4003F06D00123009372
+S31508000EEC009B012B04D002B0704700230093F7E750
+S31508000EFC1C4B1A6842F010021A601A6822F0030298
+S31508000F0C1A601A6842F002021A60A3F580535A68EE
+S31508000F1C5A605A685A605A6842F480625A605A682B
+S31508000F2C22F47C125A605A6842F4E8125A601A681B
+S31508000F3C42F080721A600A4B1B6813F0007FFAD0D5
+S31508000F4C074B5A6822F003025A605A6842F00202AA
+S31508000F5C5A60034B5B6803F00C03082BF9D1C2E704
+S31508000F6C001002400020024008B5FFF79BFF08BDA1
+S31508000F7C08B5104B1A6842F001021A6059680E4AF5
+S31508000F8C0A405A601A6822F0847222F480321A6077
+S31508000F9C1A6822F480221A605A6822F4FE025A60F1
+S31508000FAC4FF41F029A60FFF7DFFF4FF00062034B06
+S31508000FBC9A6008BD001002400000FFF800ED00E042
+S31508000FCCF0B4CB7803F00F02154613F0100F01D0CE
+S31508000FDC8D7815430B78E3B10668002301E042616E
+S31508000FEC0133072B14D801229A400C8832EA0404E0
+S31508000FFCF6D19C000F27A74026EA070605FA04F443
+S3150800100C2643CC78282CEAD0482CE9D10261E7E7AC
+S3150800101C06600B88FF2B20D94668002302E0426144
+S3150800102C15E00133072B17D803F108040122A24057
+S3150800103C0C8832EA0404F4D19C000F27A74026EA50
+S3150800104C070605FA04F42643CC78282CE7D0CC7886
+S3150800105C482CE6D10261E4E74660F0BC7047836829
+S3150800106C194201D100207047012070470161704771
+S3150800107C4161704729B9054A936923EA00009061D2
+S3150800108C7047024A936918439061704700100240F2
+S3150800109C70B584B000230393029303F1804303F5E0
+S315080010AC04331A6842F001021A605968544A0A4015
+S315080010BC5A601A6822F0847222F480321A601A680E
+S315080010CC22F480221A605A6822F4FE025A604FF4FF
+S315080010DC1F029A601A6842F480321A60494B1B68E0
+S315080010EC03F400330293039B01330393029B23B946
+S315080010FC039A40F2DC539A42F0D1424B1B6813F424
+S3150800110C003F77D0404B1A6842F010021A601A68F2
+S3150800111C22F003021A601A6842F002021A60A3F55A
+S3150800112C80535A685A605A6842F400525A605A6890
+S3150800113C42F480625A605A6822F47C125A605A68E1
+S3150800114C42F4E8125A601A6842F080721A602D4B03
+S3150800115C1B6813F0007FFAD02A4B5A6822F0030258
+S3150800116C5A605A6842F002025A60264B5B6803F0D2
+S3150800117C0C03082BF9D1234BDA6942F40032DA61F5
+S3150800118C9A6942F005029A61204C236823F470632D
+S3150800119C2360236843F430632360236823F4704385
+S315080011AC2360236843F48043236001210420FFF75E
+S315080011BC61FF2023ADF8043003258DF80650102660
+S315080011CC8DF8076001A92046FFF7FAFE0121304683
+S315080011DCFFF750FF4FF40053ADF804308DF8065066
+S315080011EC04238DF807300DEB03010948FFF7E8FED9
+S315080011FC04B070BD68210748FFF766FB82E700BF9D
+S3150800120C0000FFF8001002400020024000080140D0
+S3150800121C00100140D013000808B5FFF739FFFFF797
+S3150800122C83FBFFF78FFBFCE7DFF834D0002103E0E4
+S3150800123C0C4B5B58435004310B480C4B42189A42E2
+S3150800124CF6D30B4A02E0002342F8043B094B9A42B8
+S3150800125CF9D3FFF78DFE00F011F8FFF7DDFF7047A5
+S3150800126C00500020E41300080000002004000020B1
+S3150800127C0400002010050020FEE7000070B50025CC
+S3150800128C0C4E0D4CA41BA410A54209D100F01AF85B
+S3150800129C00250A4E0A4CA41BA410A54205D170BD04
+S315080012AC56F8253098470135EEE756F82530984715
+S315080012BC0135F2E7DC130008DC130008DC13000820
+S315080012CCE0130008F8B500BFF8BC08BC9E4670478A
+S311080012DCF8B500BFF8BC08BC9E46704779
+S315080012E80020000800200000010000000040000857
+S315080012F8002000000200000000600008002000002E
+S315080013080300000000800008002000000400000018
+S3150800131800A00008002000000500000000C0000822
+S31508001328002000000600000000E000080020000079
+S31508001338070000000000010800200000080000005F
+S3150800134800200108002000000900000000400108EC
+S31508001358002000000A0000000060010800200000C4
+S315080013680B00000000800108002000000C000000A7
+S3150800137800A00108002000000D00000000C00108B8
+S31508001388002000000E00000000E001080020000010
+S315080013980F0000002E2E2F2E2E2F2E2E2F2E2E2FFC
+S315080013A8536F757263652F41524D434D335F5354DE
+S315080013B84D333246312F756172742E630000000072
+S315080013C84F70656E424C54002E2E2F6D61696E2E35
+S309080013D863000000A0
+S309080013DC31010008C5
+S309080013E00D010008E5
+S309080013E404000000F3
+S70508001235AB
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/blt_conf.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/blt_conf.h
new file mode 100644
index 00000000..41b2e82a
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/blt_conf.h
@@ -0,0 +1,165 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Boot\blt_conf.h
+* \brief Bootloader configuration header file.
+* \ingroup Boot_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+#ifndef BLT_CONF_H
+#define BLT_CONF_H
+
+/****************************************************************************************
+* C P U D R I V E R C O N F I G U R A T I O N
+****************************************************************************************/
+/* To properly initialize the baudrate clocks of the communication interface, typically
+ * the speed of the crystal oscillator and/or the speed at which the system runs is
+ * needed. Set these through configurables BOOT_CPU_XTAL_SPEED_KHZ and
+ * BOOT_CPU_SYSTEM_SPEED_KHZ, respectively. To enable data exchange with the host that is
+ * not dependent on the targets architecture, the byte ordering needs to be known.
+ * Setting BOOT_CPU_BYTE_ORDER_MOTOROLA to 1 selects big endian mode and 0 selects
+ * little endian mode.
+ *
+ * Set BOOT_CPU_USER_PROGRAM_START_HOOK to 1 if you would like a hook function to be
+ * called the moment the user program is about to be started. This could be used to
+ * de-initialize application specific parts, for example to stop blinking an LED, etc.
+ */
+/** \brief Frequency of the external crystal oscillator. */
+#define BOOT_CPU_XTAL_SPEED_KHZ (8000)
+/** \brief Desired system speed. */
+#define BOOT_CPU_SYSTEM_SPEED_KHZ (72000)
+/** \brief Motorola or Intel style byte ordering. */
+#define BOOT_CPU_BYTE_ORDER_MOTOROLA (0)
+/** \brief Enable/disable hook function call right before user program start. */
+#define BOOT_CPU_USER_PROGRAM_START_HOOK (1)
+
+
+/****************************************************************************************
+* C O M M U N I C A T I O N I N T E R F A C E C O N F I G U R A T I O N
+****************************************************************************************/
+/* The UART communication interface is selected by setting the BOOT_COM_UART_ENABLE
+ * configurable to 1. Configurable BOOT_COM_UART_BAUDRATE selects the communication speed
+ * in bits/second. The maximum amount of data bytes in a message for data transmission
+ * and reception is set through BOOT_COM_UART_TX_MAX_DATA and BOOT_COM_UART_RX_MAX_DATA,
+ * respectively. It is common for a microcontroller to have more than 1 UART interface
+ * on board. The zero-based BOOT_COM_UART_CHANNEL_INDEX selects the UART interface.
+ *
+ */
+/** \brief Enable/disable UART transport layer. */
+#define BOOT_COM_UART_ENABLE (1)
+/** \brief Configure the desired communication speed. */
+#define BOOT_COM_UART_BAUDRATE (57600)
+/** \brief Configure number of bytes in the target->host data packet. */
+#define BOOT_COM_UART_TX_MAX_DATA (64)
+/** \brief Configure number of bytes in the host->target data packet. */
+#define BOOT_COM_UART_RX_MAX_DATA (64)
+/** \brief Select the desired UART peripheral as a zero based index. */
+#define BOOT_COM_UART_CHANNEL_INDEX (1)
+
+
+/****************************************************************************************
+* B A C K D O O R E N T R Y C O N F I G U R A T I O N
+****************************************************************************************/
+/* It is possible to implement an application specific method to force the bootloader to
+ * stay active after a reset. Such a backdoor entry into the bootloader is desired in
+ * situations where the user program does not run properly and therefore cannot
+ * reactivate the bootloader. By enabling these hook functions, the application can
+ * implement the backdoor, which overrides the default backdoor entry that is programmed
+ * into the bootloader. When desired for security purposes, these hook functions can
+ * also be implemented in a way that disables the backdoor entry altogether.
+ */
+/** \brief Enable/disable the backdoor override hook functions. */
+#define BOOT_BACKDOOR_HOOKS_ENABLE (0)
+
+
+/****************************************************************************************
+* N O N - V O L A T I L E M E M O R Y D R I V E R C O N F I G U R A T I O N
+****************************************************************************************/
+/* The NVM driver typically supports erase and program operations of the internal memory
+ * present on the microcontroller. Through these hook functions the NVM driver can be
+ * extended to support additional memory types such as external flash memory and serial
+ * eeproms. The size of the internal memory in kilobytes is specified with configurable
+ * BOOT_NVM_SIZE_KB. If desired the internal checksum writing and verification method can
+ * be overridden with a application specific method by enabling configuration switch
+ * BOOT_NVM_CHECKSUM_HOOKS_ENABLE.
+ */
+/** \brief Enable/disable the NVM hook function for supporting additional memory devices. */
+#define BOOT_NVM_HOOKS_ENABLE (0)
+/** \brief Configure the size of the default memory device (typically flash EEPROM). */
+#define BOOT_NVM_SIZE_KB (128)
+/** \brief Enable/disable hooks functions to override the user program checksum handling. */
+#define BOOT_NVM_CHECKSUM_HOOKS_ENABLE (0)
+
+
+/****************************************************************************************
+* F L A S H M E M O R Y D R I V E R C O N F I G U R A T I O N
+****************************************************************************************/
+/** \brief This microcontroller has a smaller vector table then the default STM32F1xx
+ * project as assumed in the bootloader's core. This means the user program has
+ * a different checksum location, because this one is added at the end of the
+ * user program's vector table.
+ */
+#define BOOT_FLASH_VECTOR_TABLE_CS_OFFSET (0x10c)
+/** \brief Enable support for a custom flash layout table. It is located in
+ * flash_layout.c. This was done because the default flashLayout[] table
+ * in the bootloader's core has more flash memory reserved for the bootloader
+ * than is needed for this demo.
+ */
+#define BOOT_FLASH_CUSTOM_LAYOUT_ENABLE (1)
+
+
+/****************************************************************************************
+* W A T C H D O G D R I V E R C O N F I G U R A T I O N
+****************************************************************************************/
+/* The COP driver cannot be configured internally in the bootloader, because its use
+ * and configuration is application specific. The bootloader does need to service the
+ * watchdog in case it is used. When the application requires the use of a watchdog,
+ * set BOOT_COP_HOOKS_ENABLE to be able to initialize and service the watchdog through
+ * hook functions.
+ */
+/** \brief Enable/disable the hook functions for controlling the watchdog. */
+#define BOOT_COP_HOOKS_ENABLE (1)
+
+
+/****************************************************************************************
+* S E E D / K E Y S E C U R I T Y C O N F I G U R A T I O N
+****************************************************************************************/
+/* A security mechanism can be enabled in the bootloader's XCP module by setting configu-
+ * rable BOOT_XCP_SEED_KEY_ENABLE to 1. Before any memory erase or programming
+ * operations can be performed, access to this resource need to be unlocked.
+ * In the Microboot settings on tab "XCP Protection" you need to specify a DLL that
+ * implements the unlocking algorithm. The demo programs are configured for the (simple)
+ * algorithm in "FeaserKey.dll". The source code for this DLL is available so it can be
+ * customized to your needs.
+ * During the unlock sequence, Microboot requests a seed from the bootloader, which is in
+ * the format of a byte array. Using this seed the unlock algorithm in the DLL computes
+ * a key, which is also a byte array, and sends this back to the bootloader. The
+ * bootloader then verifies this key to determine if programming and erase operations are
+ * permitted.
+ * After enabling this feature the hook functions XcpGetSeedHook() and XcpVerifyKeyHook()
+ * are called by the bootloader to obtain the seed and to verify the key, respectively.
+ */
+#define BOOT_XCP_SEED_KEY_ENABLE (0)
+
+
+#endif /* BLT_CONF_H */
+/*********************************** end of blt_conf.h *********************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/boot.dox b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/boot.dox
new file mode 100644
index 00000000..51cc4a4f
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/boot.dox
@@ -0,0 +1,7 @@
+/**
+\defgroup Boot_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio Bootloader
+\brief Bootloader.
+\ingroup ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+*/
+
+
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/flash_layout.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/flash_layout.c
new file mode 100644
index 00000000..e99b4774
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/flash_layout.c
@@ -0,0 +1,59 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Boot\flash_layout.c
+* \brief Custom flash layout table source file.
+* \ingroup Boot_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+
+/** \brief Array wit the layout of the flash memory.
+ * \details Also controls what part of the flash memory is reserved for the bootloader.
+ * If the bootloader size changes, the reserved sectors for the bootloader
+ * might need adjustment to make sure the bootloader doesn't get overwritten.
+ */
+static const tFlashSector flashLayout[] =
+{
+ /* space is reserved for a bootloader configuration with all supported communication
+ * interfaces enabled. when for example only UART is needed, than the space required
+ * for the bootloader can be made a lot smaller here.
+ */
+ /* { 0x08000000, 0x02000, 0}, flash sector 0 - reserved for bootloader */
+ { 0x08002000, 0x02000, 1}, /* flash sector 1 - 8kb */
+ { 0x08004000, 0x02000, 2}, /* flash sector 2 - 8kb */
+ { 0x08006000, 0x02000, 3}, /* flash sector 3 - 8kb */
+ { 0x08008000, 0x02000, 4}, /* flash sector 4 - 8kb */
+ { 0x0800A000, 0x02000, 5}, /* flash sector 5 - 8kb */
+ { 0x0800C000, 0x02000, 6}, /* flash sector 6 - 8kb */
+ { 0x0800E000, 0x02000, 7}, /* flash sector 7 - 8kb */
+ { 0x08010000, 0x02000, 8}, /* flash sector 8 - 8kb */
+ { 0x08012000, 0x02000, 9}, /* flash sector 9 - 8kb */
+ { 0x08014000, 0x02000, 10}, /* flash sector 10 - 8kb */
+ { 0x08016000, 0x02000, 11}, /* flash sector 11 - 8kb */
+ { 0x08018000, 0x02000, 12}, /* flash sector 12 - 8kb */
+ { 0x0801A000, 0x02000, 13}, /* flash sector 13 - 8kb */
+ { 0x0801C000, 0x02000, 14}, /* flash sector 14 - 8kb */
+ { 0x0801E000, 0x02000, 15}, /* flash sector 15 - 8kb */
+};
+
+
+/*********************************** end of flash_layout.c *****************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/hooks.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/hooks.c
new file mode 100644
index 00000000..c33039c5
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/hooks.c
@@ -0,0 +1,306 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Boot\hooks.c
+* \brief Bootloader callback source file.
+* \ingroup Boot_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+
+/****************************************************************************************
+* Include files
+****************************************************************************************/
+#include "boot.h" /* bootloader generic header */
+#include "led.h" /* LED driver header */
+#include "stm32f10x.h" /* microcontroller registers */
+
+
+/****************************************************************************************
+* B A C K D O O R E N T R Y H O O K F U N C T I O N S
+****************************************************************************************/
+
+#if (BOOT_BACKDOOR_HOOKS_ENABLE > 0)
+/************************************************************************************//**
+** \brief Initializes the backdoor entry option.
+** \return none.
+**
+****************************************************************************************/
+void BackDoorInitHook(void)
+{
+} /*** end of BackDoorInitHook ***/
+
+
+/************************************************************************************//**
+** \brief Checks if a backdoor entry is requested.
+** \return BLT_TRUE if the backdoor entry is requested, BLT_FALSE otherwise.
+**
+****************************************************************************************/
+blt_bool BackDoorEntryHook(void)
+{
+ /* default implementation always activates the bootloader after a reset */
+ return BLT_TRUE;
+} /*** end of BackDoorEntryHook ***/
+#endif /* BOOT_BACKDOOR_HOOKS_ENABLE > 0 */
+
+
+/****************************************************************************************
+* C P U D R I V E R H O O K F U N C T I O N S
+****************************************************************************************/
+
+#if (BOOT_CPU_USER_PROGRAM_START_HOOK > 0)
+/************************************************************************************//**
+** \brief Callback that gets called when the bootloader is about to exit and
+** hand over control to the user program. This is the last moment that
+** some final checking can be performed and if necessary prevent the
+** bootloader from activiting the user program.
+** \return BLT_TRUE if it is okay to start the user program, BLT_FALSE to keep
+** keep the bootloader active.
+**
+****************************************************************************************/
+blt_bool CpuUserProgramStartHook(void)
+{
+ /* clean up the LED driver */
+ LedBlinkExit();
+
+ /* additional and optional backdoor entry through the pushbutton on the board. to
+ * force the bootloader to stay active after reset, keep it pressed during reset.
+ */
+ if (GPIO_ReadInputDataBit(GPIOC, GPIO_Pin_13) == Bit_RESET)
+ {
+ /* pushbutton pressed, so do not start the user program and keep the
+ * bootloader active instead.
+ */
+ return BLT_FALSE;
+ }
+ /* okay to start the user program.*/
+ return BLT_TRUE;
+} /*** end of CpuUserProgramStartHook ***/
+#endif /* BOOT_CPU_USER_PROGRAM_START_HOOK > 0 */
+
+
+/****************************************************************************************
+* W A T C H D O G D R I V E R H O O K F U N C T I O N S
+****************************************************************************************/
+
+#if (BOOT_COP_HOOKS_ENABLE > 0)
+/************************************************************************************//**
+** \brief Callback that gets called at the end of the internal COP driver
+** initialization routine. It can be used to configure and enable the
+** watchdog.
+** \return none.
+**
+****************************************************************************************/
+void CopInitHook(void)
+{
+ /* this function is called upon initialization. might as well use it to initialize
+ * the LED driver. It is kind of a visual watchdog anyways.
+ */
+ LedBlinkInit(100);
+} /*** end of CopInitHook ***/
+
+
+/************************************************************************************//**
+** \brief Callback that gets called at the end of the internal COP driver
+** service routine. This gets called upon initialization and during
+** potential long lasting loops and routine. It can be used to service
+** the watchdog to prevent a watchdog reset.
+** \return none.
+**
+****************************************************************************************/
+void CopServiceHook(void)
+{
+ /* run the LED blink task. this is a better place to do it than in the main() program
+ * loop. certain operations such as flash erase can take a long time, which would cause
+ * a blink interval to be skipped. this function is also called during such operations,
+ * so no blink intervals will be skipped when calling the LED blink task here.
+ */
+ LedBlinkTask();
+} /*** end of CopServiceHook ***/
+#endif /* BOOT_COP_HOOKS_ENABLE > 0 */
+
+
+/****************************************************************************************
+* N O N - V O L A T I L E M E M O R Y D R I V E R H O O K F U N C T I O N S
+****************************************************************************************/
+
+#if (BOOT_NVM_HOOKS_ENABLE > 0)
+/************************************************************************************//**
+** \brief Callback that gets called at the start of the internal NVM driver
+** initialization routine.
+** \return none.
+**
+****************************************************************************************/
+void NvmInitHook(void)
+{
+} /*** end of NvmInitHook ***/
+
+
+/************************************************************************************//**
+** \brief Callback that gets called at the start of a firmware update to reinitialize
+** the NVM driver.
+** \return none.
+**
+****************************************************************************************/
+void NvmReinitHook(void)
+{
+} /*** end of NvmReinitHook ***/
+
+
+/************************************************************************************//**
+** \brief Callback that gets called at the start of the NVM driver write
+** routine. It allows additional memory to be operated on. If the address
+** is not within the range of the additional memory, then
+** BLT_NVM_NOT_IN_RANGE must be returned to indicate that the data hasn't
+** been written yet.
+** \param addr Start address.
+** \param len Length in bytes.
+** \param data Pointer to the data buffer.
+** \return BLT_NVM_OKAY if successful, BLT_NVM_NOT_IN_RANGE if the address is
+** not within the supported memory range, or BLT_NVM_ERROR is the write
+** operation failed.
+**
+****************************************************************************************/
+blt_int8u NvmWriteHook(blt_addr addr, blt_int32u len, blt_int8u *data)
+{
+ return BLT_NVM_NOT_IN_RANGE;
+} /*** end of NvmWriteHook ***/
+
+
+/************************************************************************************//**
+** \brief Callback that gets called at the start of the NVM driver erase
+** routine. It allows additional memory to be operated on. If the address
+** is not within the range of the additional memory, then
+** BLT_NVM_NOT_IN_RANGE must be returned to indicate that the memory
+** hasn't been erased yet.
+** \param addr Start address.
+** \param len Length in bytes.
+** \return BLT_NVM_OKAY if successful, BLT_NVM_NOT_IN_RANGE if the address is
+** not within the supported memory range, or BLT_NVM_ERROR is the erase
+** operation failed.
+**
+****************************************************************************************/
+blt_int8u NvmEraseHook(blt_addr addr, blt_int32u len)
+{
+ return BLT_NVM_NOT_IN_RANGE;
+} /*** end of NvmEraseHook ***/
+
+
+/************************************************************************************//**
+** \brief Callback that gets called at the end of the NVM programming session.
+** \return BLT_TRUE is successful, BLT_FALSE otherwise.
+**
+****************************************************************************************/
+blt_bool NvmDoneHook(void)
+{
+ return BLT_TRUE;
+} /*** end of NvmDoneHook ***/
+#endif /* BOOT_NVM_HOOKS_ENABLE > 0 */
+
+
+#if (BOOT_NVM_CHECKSUM_HOOKS_ENABLE > 0)
+/************************************************************************************//**
+** \brief Verifies the checksum, which indicates that a valid user program is
+** present and can be started.
+** \return BLT_TRUE if successful, BLT_FALSE otherwise.
+**
+****************************************************************************************/
+blt_bool NvmVerifyChecksumHook(void)
+{
+ return BLT_TRUE;
+} /*** end of NvmVerifyChecksum ***/
+
+
+/************************************************************************************//**
+** \brief Writes a checksum of the user program to non-volatile memory. This is
+** performed once the entire user program has been programmed. Through
+** the checksum, the bootloader can check if a valid user programming is
+** present and can be started.
+** \return BLT_TRUE if successful, BLT_FALSE otherwise.
+**
+****************************************************************************************/
+blt_bool NvmWriteChecksumHook(void)
+{
+ return BLT_TRUE;
+}
+#endif /* BOOT_NVM_CHECKSUM_HOOKS_ENABLE > 0 */
+
+
+/****************************************************************************************
+* S E E D / K E Y S E C U R I T Y H O O K F U N C T I O N S
+****************************************************************************************/
+
+#if (BOOT_XCP_SEED_KEY_ENABLE > 0)
+/************************************************************************************//**
+** \brief Provides a seed to the XCP master that will be used for the key
+** generation when the master attempts to unlock the specified resource.
+** Called by the GET_SEED command.
+** \param resource Resource that the seed if requested for (XCP_RES_XXX).
+** \param seed Pointer to byte buffer wher the seed will be stored.
+** \return Length of the seed in bytes.
+**
+****************************************************************************************/
+blt_int8u XcpGetSeedHook(blt_int8u resource, blt_int8u *seed)
+{
+ /* request seed for unlocking ProGraMming resource */
+ if ((resource & XCP_RES_PGM) != 0)
+ {
+ seed[0] = 0x55;
+ }
+
+ /* return seed length */
+ return 1;
+} /*** end of XcpGetSeedHook ***/
+
+
+/************************************************************************************//**
+** \brief Called by the UNLOCK command and checks if the key to unlock the
+** specified resource was correct. If so, then the resource protection
+** will be removed.
+** \param resource resource to unlock (XCP_RES_XXX).
+** \param key pointer to the byte buffer holding the key.
+** \param len length of the key in bytes.
+** \return 1 if the key was correct, 0 otherwise.
+**
+****************************************************************************************/
+blt_int8u XcpVerifyKeyHook(blt_int8u resource, blt_int8u *key, blt_int8u len)
+{
+ /* suppress compiler warning for unused parameter */
+ len = len;
+
+ /* the example key algorithm in "FeaserKey.dll" works as follows:
+ * - PGM will be unlocked if key = seed - 1
+ */
+
+ /* check key for unlocking ProGraMming resource */
+ if ((resource == XCP_RES_PGM) && (key[0] == (0x55-1)))
+ {
+ /* correct key received for unlocking PGM resource */
+ return 1;
+ }
+
+ /* still here so key incorrect */
+ return 0;
+} /*** end of XcpVerifyKeyHook ***/
+#endif /* BOOT_XCP_SEED_KEY_ENABLE > 0 */
+
+
+/*********************************** end of hooks.c ************************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/led.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/led.c
new file mode 100644
index 00000000..b6cb08ad
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/led.c
@@ -0,0 +1,100 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Boot\led.c
+* \brief LED driver source file.
+* \ingroup Boot_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+
+/****************************************************************************************
+* Include files
+****************************************************************************************/
+#include "boot.h" /* bootloader generic header */
+#include "led.h" /* module header */
+#include "stm32f10x.h" /* STM32 register definitions */
+
+
+/****************************************************************************************
+* Local data declarations
+****************************************************************************************/
+/** \brief Holds the desired LED blink interval time. */
+static blt_int16u ledBlinkIntervalMs;
+
+
+/************************************************************************************//**
+** \brief Initializes the LED blink driver.
+** \param interval_ms Specifies the desired LED blink interval time in milliseconds.
+** \return none.
+**
+****************************************************************************************/
+void LedBlinkInit(blt_int16u interval_ms)
+{
+ /* store the interval time between LED toggles */
+ ledBlinkIntervalMs = interval_ms;
+} /*** end of LedBlinkInit ***/
+
+
+/************************************************************************************//**
+** \brief Task function for blinking the LED as a fixed timer interval.
+** \return none.
+**
+****************************************************************************************/
+void LedBlinkTask(void)
+{
+ static blt_bool ledOn = BLT_FALSE;
+ static blt_int32u nextBlinkEvent = 0;
+
+ /* check for blink event */
+ if (TimerGet() >= nextBlinkEvent)
+ {
+ /* toggle the LED state */
+ if (ledOn == BLT_FALSE)
+ {
+ ledOn = BLT_TRUE;
+ GPIO_SetBits(GPIOA, GPIO_Pin_5);
+ }
+ else
+ {
+ ledOn = BLT_FALSE;
+ GPIO_ResetBits(GPIOA, GPIO_Pin_5);
+ }
+ /* schedule the next blink event */
+ nextBlinkEvent = TimerGet() + ledBlinkIntervalMs;
+ }
+} /*** end of LedBlinkTask ***/
+
+
+/************************************************************************************//**
+** \brief Cleans up the LED blink driver. This is intended to be used upon program
+** exit.
+** \return none.
+**
+****************************************************************************************/
+void LedBlinkExit(void)
+{
+ /* turn the LED off */
+ GPIO_ResetBits(GPIOA, GPIO_Pin_5);
+} /*** end of LedBlinkExit ***/
+
+
+/*********************************** end of led.c **************************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/led.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/led.h
new file mode 100644
index 00000000..e7943376
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/led.h
@@ -0,0 +1,40 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Boot\led.h
+* \brief LED driver header file.
+* \ingroup Boot_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+#ifndef LED_H
+#define LED_H
+
+/****************************************************************************************
+* Function prototypes
+****************************************************************************************/
+void LedBlinkInit(blt_int16u interval_ms);
+void LedBlinkTask(void);
+void LedBlinkExit(void);
+
+
+#endif /* LED_H */
+/*********************************** end of led.h **************************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/CoreSupport/core_cm3.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/CoreSupport/core_cm3.c
new file mode 100644
index 00000000..0e8c3c43
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/CoreSupport/core_cm3.c
@@ -0,0 +1,784 @@
+/**************************************************************************//**
+ * @file core_cm3.c
+ * @brief CMSIS Cortex-M3 Core Peripheral Access Layer Source File
+ * @version V1.30
+ * @date 30. October 2009
+ *
+ * @note
+ * Copyright (C) 2009 ARM Limited. All rights reserved.
+ *
+ * @par
+ * ARM Limited (ARM) is supplying this software for use with Cortex-M
+ * processor based microcontrollers. This file can be freely distributed
+ * within development tools that are supporting such ARM based processors.
+ *
+ * @par
+ * THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED
+ * OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.
+ * ARM SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR
+ * CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
+ *
+ ******************************************************************************/
+
+#include
+
+/* define compiler specific symbols */
+#if defined ( __CC_ARM )
+ #define __ASM __asm /*!< asm keyword for ARM Compiler */
+ #define __INLINE __inline /*!< inline keyword for ARM Compiler */
+
+#elif defined ( __ICCARM__ )
+ #define __ASM __asm /*!< asm keyword for IAR Compiler */
+ #define __INLINE inline /*!< inline keyword for IAR Compiler. Only avaiable in High optimization mode! */
+
+#elif defined ( __GNUC__ )
+ #define __ASM __asm /*!< asm keyword for GNU Compiler */
+ #define __INLINE inline /*!< inline keyword for GNU Compiler */
+
+#elif defined ( __TASKING__ )
+ #define __ASM __asm /*!< asm keyword for TASKING Compiler */
+ #define __INLINE inline /*!< inline keyword for TASKING Compiler */
+
+#endif
+
+
+/* ################### Compiler specific Intrinsics ########################### */
+
+#if defined ( __CC_ARM ) /*------------------RealView Compiler -----------------*/
+/* ARM armcc specific functions */
+
+/**
+ * @brief Return the Process Stack Pointer
+ *
+ * @return ProcessStackPointer
+ *
+ * Return the actual process stack pointer
+ */
+__ASM uint32_t __get_PSP(void)
+{
+ mrs r0, psp
+ bx lr
+}
+
+/**
+ * @brief Set the Process Stack Pointer
+ *
+ * @param topOfProcStack Process Stack Pointer
+ *
+ * Assign the value ProcessStackPointer to the MSP
+ * (process stack pointer) Cortex processor register
+ */
+__ASM void __set_PSP(uint32_t topOfProcStack)
+{
+ msr psp, r0
+ bx lr
+}
+
+/**
+ * @brief Return the Main Stack Pointer
+ *
+ * @return Main Stack Pointer
+ *
+ * Return the current value of the MSP (main stack pointer)
+ * Cortex processor register
+ */
+__ASM uint32_t __get_MSP(void)
+{
+ mrs r0, msp
+ bx lr
+}
+
+/**
+ * @brief Set the Main Stack Pointer
+ *
+ * @param topOfMainStack Main Stack Pointer
+ *
+ * Assign the value mainStackPointer to the MSP
+ * (main stack pointer) Cortex processor register
+ */
+__ASM void __set_MSP(uint32_t mainStackPointer)
+{
+ msr msp, r0
+ bx lr
+}
+
+/**
+ * @brief Reverse byte order in unsigned short value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in unsigned short value
+ */
+__ASM uint32_t __REV16(uint16_t value)
+{
+ rev16 r0, r0
+ bx lr
+}
+
+/**
+ * @brief Reverse byte order in signed short value with sign extension to integer
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in signed short value with sign extension to integer
+ */
+__ASM int32_t __REVSH(int16_t value)
+{
+ revsh r0, r0
+ bx lr
+}
+
+
+#if (__ARMCC_VERSION < 400000)
+
+/**
+ * @brief Remove the exclusive lock created by ldrex
+ *
+ * Removes the exclusive lock which is created by ldrex.
+ */
+__ASM void __CLREX(void)
+{
+ clrex
+}
+
+/**
+ * @brief Return the Base Priority value
+ *
+ * @return BasePriority
+ *
+ * Return the content of the base priority register
+ */
+__ASM uint32_t __get_BASEPRI(void)
+{
+ mrs r0, basepri
+ bx lr
+}
+
+/**
+ * @brief Set the Base Priority value
+ *
+ * @param basePri BasePriority
+ *
+ * Set the base priority register
+ */
+__ASM void __set_BASEPRI(uint32_t basePri)
+{
+ msr basepri, r0
+ bx lr
+}
+
+/**
+ * @brief Return the Priority Mask value
+ *
+ * @return PriMask
+ *
+ * Return state of the priority mask bit from the priority mask register
+ */
+__ASM uint32_t __get_PRIMASK(void)
+{
+ mrs r0, primask
+ bx lr
+}
+
+/**
+ * @brief Set the Priority Mask value
+ *
+ * @param priMask PriMask
+ *
+ * Set the priority mask bit in the priority mask register
+ */
+__ASM void __set_PRIMASK(uint32_t priMask)
+{
+ msr primask, r0
+ bx lr
+}
+
+/**
+ * @brief Return the Fault Mask value
+ *
+ * @return FaultMask
+ *
+ * Return the content of the fault mask register
+ */
+__ASM uint32_t __get_FAULTMASK(void)
+{
+ mrs r0, faultmask
+ bx lr
+}
+
+/**
+ * @brief Set the Fault Mask value
+ *
+ * @param faultMask faultMask value
+ *
+ * Set the fault mask register
+ */
+__ASM void __set_FAULTMASK(uint32_t faultMask)
+{
+ msr faultmask, r0
+ bx lr
+}
+
+/**
+ * @brief Return the Control Register value
+ *
+ * @return Control value
+ *
+ * Return the content of the control register
+ */
+__ASM uint32_t __get_CONTROL(void)
+{
+ mrs r0, control
+ bx lr
+}
+
+/**
+ * @brief Set the Control Register value
+ *
+ * @param control Control value
+ *
+ * Set the control register
+ */
+__ASM void __set_CONTROL(uint32_t control)
+{
+ msr control, r0
+ bx lr
+}
+
+#endif /* __ARMCC_VERSION */
+
+
+
+#elif (defined (__ICCARM__)) /*------------------ ICC Compiler -------------------*/
+/* IAR iccarm specific functions */
+#pragma diag_suppress=Pe940
+
+/**
+ * @brief Return the Process Stack Pointer
+ *
+ * @return ProcessStackPointer
+ *
+ * Return the actual process stack pointer
+ */
+uint32_t __get_PSP(void)
+{
+ __ASM("mrs r0, psp");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief Set the Process Stack Pointer
+ *
+ * @param topOfProcStack Process Stack Pointer
+ *
+ * Assign the value ProcessStackPointer to the MSP
+ * (process stack pointer) Cortex processor register
+ */
+void __set_PSP(uint32_t topOfProcStack)
+{
+ __ASM("msr psp, r0");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief Return the Main Stack Pointer
+ *
+ * @return Main Stack Pointer
+ *
+ * Return the current value of the MSP (main stack pointer)
+ * Cortex processor register
+ */
+uint32_t __get_MSP(void)
+{
+ __ASM("mrs r0, msp");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief Set the Main Stack Pointer
+ *
+ * @param topOfMainStack Main Stack Pointer
+ *
+ * Assign the value mainStackPointer to the MSP
+ * (main stack pointer) Cortex processor register
+ */
+void __set_MSP(uint32_t topOfMainStack)
+{
+ __ASM("msr msp, r0");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief Reverse byte order in unsigned short value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in unsigned short value
+ */
+uint32_t __REV16(uint16_t value)
+{
+ __ASM("rev16 r0, r0");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief Reverse bit order of value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse bit order of value
+ */
+uint32_t __RBIT(uint32_t value)
+{
+ __ASM("rbit r0, r0");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief LDR Exclusive (8 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 8 bit values)
+ */
+uint8_t __LDREXB(uint8_t *addr)
+{
+ __ASM("ldrexb r0, [r0]");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief LDR Exclusive (16 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 16 bit values
+ */
+uint16_t __LDREXH(uint16_t *addr)
+{
+ __ASM("ldrexh r0, [r0]");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief LDR Exclusive (32 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 32 bit values
+ */
+uint32_t __LDREXW(uint32_t *addr)
+{
+ __ASM("ldrex r0, [r0]");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief STR Exclusive (8 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 8 bit values
+ */
+uint32_t __STREXB(uint8_t value, uint8_t *addr)
+{
+ __ASM("strexb r0, r0, [r1]");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief STR Exclusive (16 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 16 bit values
+ */
+uint32_t __STREXH(uint16_t value, uint16_t *addr)
+{
+ __ASM("strexh r0, r0, [r1]");
+ __ASM("bx lr");
+}
+
+/**
+ * @brief STR Exclusive (32 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 32 bit values
+ */
+uint32_t __STREXW(uint32_t value, uint32_t *addr)
+{
+ __ASM("strex r0, r0, [r1]");
+ __ASM("bx lr");
+}
+
+#pragma diag_default=Pe940
+
+
+#elif (defined (__GNUC__)) /*------------------ GNU Compiler ---------------------*/
+/* GNU gcc specific functions */
+
+/**
+ * @brief Return the Process Stack Pointer
+ *
+ * @return ProcessStackPointer
+ *
+ * Return the actual process stack pointer
+ */
+uint32_t __get_PSP(void) __attribute__( ( naked ) );
+uint32_t __get_PSP(void)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("MRS %0, psp\n\t"
+ "MOV r0, %0 \n\t"
+ "BX lr \n\t" : "=r" (result) );
+ return(result);
+}
+
+/**
+ * @brief Set the Process Stack Pointer
+ *
+ * @param topOfProcStack Process Stack Pointer
+ *
+ * Assign the value ProcessStackPointer to the MSP
+ * (process stack pointer) Cortex processor register
+ */
+void __set_PSP(uint32_t topOfProcStack) __attribute__( ( naked ) );
+void __set_PSP(uint32_t topOfProcStack)
+{
+ __ASM volatile ("MSR psp, %0\n\t"
+ "BX lr \n\t" : : "r" (topOfProcStack) );
+}
+
+/**
+ * @brief Return the Main Stack Pointer
+ *
+ * @return Main Stack Pointer
+ *
+ * Return the current value of the MSP (main stack pointer)
+ * Cortex processor register
+ */
+uint32_t __get_MSP(void) __attribute__( ( naked ) );
+uint32_t __get_MSP(void)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("MRS %0, msp\n\t"
+ "MOV r0, %0 \n\t"
+ "BX lr \n\t" : "=r" (result) );
+ return(result);
+}
+
+/**
+ * @brief Set the Main Stack Pointer
+ *
+ * @param topOfMainStack Main Stack Pointer
+ *
+ * Assign the value mainStackPointer to the MSP
+ * (main stack pointer) Cortex processor register
+ */
+void __set_MSP(uint32_t topOfMainStack) __attribute__( ( naked ) );
+void __set_MSP(uint32_t topOfMainStack)
+{
+ __ASM volatile ("MSR msp, %0\n\t"
+ "BX lr \n\t" : : "r" (topOfMainStack) );
+}
+
+/**
+ * @brief Return the Base Priority value
+ *
+ * @return BasePriority
+ *
+ * Return the content of the base priority register
+ */
+uint32_t __get_BASEPRI(void)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("MRS %0, basepri_max" : "=r" (result) );
+ return(result);
+}
+
+/**
+ * @brief Set the Base Priority value
+ *
+ * @param basePri BasePriority
+ *
+ * Set the base priority register
+ */
+void __set_BASEPRI(uint32_t value)
+{
+ __ASM volatile ("MSR basepri, %0" : : "r" (value) );
+}
+
+/**
+ * @brief Return the Priority Mask value
+ *
+ * @return PriMask
+ *
+ * Return state of the priority mask bit from the priority mask register
+ */
+uint32_t __get_PRIMASK(void)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("MRS %0, primask" : "=r" (result) );
+ return(result);
+}
+
+/**
+ * @brief Set the Priority Mask value
+ *
+ * @param priMask PriMask
+ *
+ * Set the priority mask bit in the priority mask register
+ */
+void __set_PRIMASK(uint32_t priMask)
+{
+ __ASM volatile ("MSR primask, %0" : : "r" (priMask) );
+}
+
+/**
+ * @brief Return the Fault Mask value
+ *
+ * @return FaultMask
+ *
+ * Return the content of the fault mask register
+ */
+uint32_t __get_FAULTMASK(void)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("MRS %0, faultmask" : "=r" (result) );
+ return(result);
+}
+
+/**
+ * @brief Set the Fault Mask value
+ *
+ * @param faultMask faultMask value
+ *
+ * Set the fault mask register
+ */
+void __set_FAULTMASK(uint32_t faultMask)
+{
+ __ASM volatile ("MSR faultmask, %0" : : "r" (faultMask) );
+}
+
+/**
+ * @brief Return the Control Register value
+*
+* @return Control value
+ *
+ * Return the content of the control register
+ */
+uint32_t __get_CONTROL(void)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("MRS %0, control" : "=r" (result) );
+ return(result);
+}
+
+/**
+ * @brief Set the Control Register value
+ *
+ * @param control Control value
+ *
+ * Set the control register
+ */
+void __set_CONTROL(uint32_t control)
+{
+ __ASM volatile ("MSR control, %0" : : "r" (control) );
+}
+
+
+/**
+ * @brief Reverse byte order in integer value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in integer value
+ */
+uint32_t __REV(uint32_t value)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("rev %0, %1" : "=r" (result) : "r" (value) );
+ return(result);
+}
+
+/**
+ * @brief Reverse byte order in unsigned short value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in unsigned short value
+ */
+uint32_t __REV16(uint16_t value)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("rev16 %0, %1" : "=r" (result) : "r" (value) );
+ return(result);
+}
+
+/**
+ * @brief Reverse byte order in signed short value with sign extension to integer
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in signed short value with sign extension to integer
+ */
+int32_t __REVSH(int16_t value)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("revsh %0, %1" : "=r" (result) : "r" (value) );
+ return(result);
+}
+
+/**
+ * @brief Reverse bit order of value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse bit order of value
+ */
+uint32_t __RBIT(uint32_t value)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("rbit %0, %1" : "=r" (result) : "r" (value) );
+ return(result);
+}
+
+/**
+ * @brief LDR Exclusive (8 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 8 bit value
+ */
+uint8_t __LDREXB(uint8_t *addr)
+{
+ uint8_t result=0;
+
+ __ASM volatile ("ldrexb %0, [%1]" : "=r" (result) : "r" (addr) );
+ return(result);
+}
+
+/**
+ * @brief LDR Exclusive (16 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 16 bit values
+ */
+uint16_t __LDREXH(uint16_t *addr)
+{
+ uint16_t result=0;
+
+ __ASM volatile ("ldrexh %0, [%1]" : "=r" (result) : "r" (addr) );
+ return(result);
+}
+
+/**
+ * @brief LDR Exclusive (32 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 32 bit values
+ */
+uint32_t __LDREXW(uint32_t *addr)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("ldrex %0, [%1]" : "=r" (result) : "r" (addr) );
+ return(result);
+}
+
+/**
+ * @brief STR Exclusive (8 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 8 bit values
+ */
+uint32_t __STREXB(uint8_t value, uint8_t *addr)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("strexb %0, %2, [%1]" : "=&r" (result) : "r" (addr), "r" (value) );
+ return(result);
+}
+
+/**
+ * @brief STR Exclusive (16 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 16 bit values
+ */
+uint32_t __STREXH(uint16_t value, uint16_t *addr)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("strexh %0, %2, [%1]" : "=&r" (result) : "r" (addr), "r" (value) );
+ return(result);
+}
+
+/**
+ * @brief STR Exclusive (32 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 32 bit values
+ */
+uint32_t __STREXW(uint32_t value, uint32_t *addr)
+{
+ uint32_t result=0;
+
+ __ASM volatile ("strex %0, %2, [%1]" : "=r" (result) : "r" (addr), "r" (value) );
+ return(result);
+}
+
+
+#elif (defined (__TASKING__)) /*------------------ TASKING Compiler ---------------------*/
+/* TASKING carm specific functions */
+
+/*
+ * The CMSIS functions have been implemented as intrinsics in the compiler.
+ * Please use "carm -?i" to get an up to date list of all instrinsics,
+ * Including the CMSIS ones.
+ */
+
+#endif
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/CoreSupport/core_cm3.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/CoreSupport/core_cm3.h
new file mode 100644
index 00000000..2b6b51a7
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/CoreSupport/core_cm3.h
@@ -0,0 +1,1818 @@
+/**************************************************************************//**
+ * @file core_cm3.h
+ * @brief CMSIS Cortex-M3 Core Peripheral Access Layer Header File
+ * @version V1.30
+ * @date 30. October 2009
+ *
+ * @note
+ * Copyright (C) 2009 ARM Limited. All rights reserved.
+ *
+ * @par
+ * ARM Limited (ARM) is supplying this software for use with Cortex-M
+ * processor based microcontrollers. This file can be freely distributed
+ * within development tools that are supporting such ARM based processors.
+ *
+ * @par
+ * THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED
+ * OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.
+ * ARM SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR
+ * CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
+ *
+ ******************************************************************************/
+
+#ifndef __CM3_CORE_H__
+#define __CM3_CORE_H__
+
+/** @addtogroup CMSIS_CM3_core_LintCinfiguration CMSIS CM3 Core Lint Configuration
+ *
+ * List of Lint messages which will be suppressed and not shown:
+ * - Error 10: \n
+ * register uint32_t __regBasePri __asm("basepri"); \n
+ * Error 10: Expecting ';'
+ * .
+ * - Error 530: \n
+ * return(__regBasePri); \n
+ * Warning 530: Symbol '__regBasePri' (line 264) not initialized
+ * .
+ * - Error 550: \n
+ * __regBasePri = (basePri & 0x1ff); \n
+ * Warning 550: Symbol '__regBasePri' (line 271) not accessed
+ * .
+ * - Error 754: \n
+ * uint32_t RESERVED0[24]; \n
+ * Info 754: local structure member '' (line 109, file ./cm3_core.h) not referenced
+ * .
+ * - Error 750: \n
+ * #define __CM3_CORE_H__ \n
+ * Info 750: local macro '__CM3_CORE_H__' (line 43, file./cm3_core.h) not referenced
+ * .
+ * - Error 528: \n
+ * static __INLINE void NVIC_DisableIRQ(uint32_t IRQn) \n
+ * Warning 528: Symbol 'NVIC_DisableIRQ(unsigned int)' (line 419, file ./cm3_core.h) not referenced
+ * .
+ * - Error 751: \n
+ * } InterruptType_Type; \n
+ * Info 751: local typedef 'InterruptType_Type' (line 170, file ./cm3_core.h) not referenced
+ * .
+ * Note: To re-enable a Message, insert a space before 'lint' *
+ *
+ */
+
+/*lint -save */
+/*lint -e10 */
+/*lint -e530 */
+/*lint -e550 */
+/*lint -e754 */
+/*lint -e750 */
+/*lint -e528 */
+/*lint -e751 */
+
+
+/** @addtogroup CMSIS_CM3_core_definitions CM3 Core Definitions
+ This file defines all structures and symbols for CMSIS core:
+ - CMSIS version number
+ - Cortex-M core registers and bitfields
+ - Cortex-M core peripheral base address
+ @{
+ */
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#define __CM3_CMSIS_VERSION_MAIN (0x01) /*!< [31:16] CMSIS HAL main version */
+#define __CM3_CMSIS_VERSION_SUB (0x30) /*!< [15:0] CMSIS HAL sub version */
+#define __CM3_CMSIS_VERSION ((__CM3_CMSIS_VERSION_MAIN << 16) | __CM3_CMSIS_VERSION_SUB) /*!< CMSIS HAL version number */
+
+#define __CORTEX_M (0x03) /*!< Cortex core */
+
+#include /* Include standard types */
+
+#if defined (__ICCARM__)
+ #include /* IAR Intrinsics */
+#endif
+
+
+#ifndef __NVIC_PRIO_BITS
+ #define __NVIC_PRIO_BITS 4 /*!< standard definition for NVIC Priority Bits */
+#endif
+
+
+
+
+/**
+ * IO definitions
+ *
+ * define access restrictions to peripheral registers
+ */
+
+#ifdef __cplusplus
+ #define __I volatile /*!< defines 'read only' permissions */
+#else
+ #define __I volatile const /*!< defines 'read only' permissions */
+#endif
+#define __O volatile /*!< defines 'write only' permissions */
+#define __IO volatile /*!< defines 'read / write' permissions */
+
+
+
+/*******************************************************************************
+ * Register Abstraction
+ ******************************************************************************/
+/** @addtogroup CMSIS_CM3_core_register CMSIS CM3 Core Register
+ @{
+*/
+
+
+/** @addtogroup CMSIS_CM3_NVIC CMSIS CM3 NVIC
+ memory mapped structure for Nested Vectored Interrupt Controller (NVIC)
+ @{
+ */
+typedef struct
+{
+ __IO uint32_t ISER[8]; /*!< Offset: 0x000 Interrupt Set Enable Register */
+ uint32_t RESERVED0[24];
+ __IO uint32_t ICER[8]; /*!< Offset: 0x080 Interrupt Clear Enable Register */
+ uint32_t RSERVED1[24];
+ __IO uint32_t ISPR[8]; /*!< Offset: 0x100 Interrupt Set Pending Register */
+ uint32_t RESERVED2[24];
+ __IO uint32_t ICPR[8]; /*!< Offset: 0x180 Interrupt Clear Pending Register */
+ uint32_t RESERVED3[24];
+ __IO uint32_t IABR[8]; /*!< Offset: 0x200 Interrupt Active bit Register */
+ uint32_t RESERVED4[56];
+ __IO uint8_t IP[240]; /*!< Offset: 0x300 Interrupt Priority Register (8Bit wide) */
+ uint32_t RESERVED5[644];
+ __O uint32_t STIR; /*!< Offset: 0xE00 Software Trigger Interrupt Register */
+} NVIC_Type;
+/*@}*/ /* end of group CMSIS_CM3_NVIC */
+
+
+/** @addtogroup CMSIS_CM3_SCB CMSIS CM3 SCB
+ memory mapped structure for System Control Block (SCB)
+ @{
+ */
+typedef struct
+{
+ __I uint32_t CPUID; /*!< Offset: 0x00 CPU ID Base Register */
+ __IO uint32_t ICSR; /*!< Offset: 0x04 Interrupt Control State Register */
+ __IO uint32_t VTOR; /*!< Offset: 0x08 Vector Table Offset Register */
+ __IO uint32_t AIRCR; /*!< Offset: 0x0C Application Interrupt / Reset Control Register */
+ __IO uint32_t SCR; /*!< Offset: 0x10 System Control Register */
+ __IO uint32_t CCR; /*!< Offset: 0x14 Configuration Control Register */
+ __IO uint8_t SHP[12]; /*!< Offset: 0x18 System Handlers Priority Registers (4-7, 8-11, 12-15) */
+ __IO uint32_t SHCSR; /*!< Offset: 0x24 System Handler Control and State Register */
+ __IO uint32_t CFSR; /*!< Offset: 0x28 Configurable Fault Status Register */
+ __IO uint32_t HFSR; /*!< Offset: 0x2C Hard Fault Status Register */
+ __IO uint32_t DFSR; /*!< Offset: 0x30 Debug Fault Status Register */
+ __IO uint32_t MMFAR; /*!< Offset: 0x34 Mem Manage Address Register */
+ __IO uint32_t BFAR; /*!< Offset: 0x38 Bus Fault Address Register */
+ __IO uint32_t AFSR; /*!< Offset: 0x3C Auxiliary Fault Status Register */
+ __I uint32_t PFR[2]; /*!< Offset: 0x40 Processor Feature Register */
+ __I uint32_t DFR; /*!< Offset: 0x48 Debug Feature Register */
+ __I uint32_t ADR; /*!< Offset: 0x4C Auxiliary Feature Register */
+ __I uint32_t MMFR[4]; /*!< Offset: 0x50 Memory Model Feature Register */
+ __I uint32_t ISAR[5]; /*!< Offset: 0x60 ISA Feature Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos 24 /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk (0xFFul << SCB_CPUID_IMPLEMENTER_Pos) /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos 20 /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk (0xFul << SCB_CPUID_VARIANT_Pos) /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_PARTNO_Pos 4 /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk (0xFFFul << SCB_CPUID_PARTNO_Pos) /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos 0 /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk (0xFul << SCB_CPUID_REVISION_Pos) /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos 31 /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk (1ul << SCB_ICSR_NMIPENDSET_Pos) /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos 28 /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk (1ul << SCB_ICSR_PENDSVSET_Pos) /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos 27 /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk (1ul << SCB_ICSR_PENDSVCLR_Pos) /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos 26 /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk (1ul << SCB_ICSR_PENDSTSET_Pos) /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos 25 /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk (1ul << SCB_ICSR_PENDSTCLR_Pos) /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos 23 /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk (1ul << SCB_ICSR_ISRPREEMPT_Pos) /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos 22 /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk (1ul << SCB_ICSR_ISRPENDING_Pos) /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos 12 /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk (0x1FFul << SCB_ICSR_VECTPENDING_Pos) /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_RETTOBASE_Pos 11 /*!< SCB ICSR: RETTOBASE Position */
+#define SCB_ICSR_RETTOBASE_Msk (1ul << SCB_ICSR_RETTOBASE_Pos) /*!< SCB ICSR: RETTOBASE Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos 0 /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk (0x1FFul << SCB_ICSR_VECTACTIVE_Pos) /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_VTOR_TBLBASE_Pos 29 /*!< SCB VTOR: TBLBASE Position */
+#define SCB_VTOR_TBLBASE_Msk (0x1FFul << SCB_VTOR_TBLBASE_Pos) /*!< SCB VTOR: TBLBASE Mask */
+
+#define SCB_VTOR_TBLOFF_Pos 7 /*!< SCB VTOR: TBLOFF Position */
+#define SCB_VTOR_TBLOFF_Msk (0x3FFFFFul << SCB_VTOR_TBLOFF_Pos) /*!< SCB VTOR: TBLOFF Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos 16 /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk (0xFFFFul << SCB_AIRCR_VECTKEY_Pos) /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos 16 /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk (0xFFFFul << SCB_AIRCR_VECTKEYSTAT_Pos) /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos 15 /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk (1ul << SCB_AIRCR_ENDIANESS_Pos) /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_PRIGROUP_Pos 8 /*!< SCB AIRCR: PRIGROUP Position */
+#define SCB_AIRCR_PRIGROUP_Msk (7ul << SCB_AIRCR_PRIGROUP_Pos) /*!< SCB AIRCR: PRIGROUP Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos 2 /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk (1ul << SCB_AIRCR_SYSRESETREQ_Pos) /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos 1 /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk (1ul << SCB_AIRCR_VECTCLRACTIVE_Pos) /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+#define SCB_AIRCR_VECTRESET_Pos 0 /*!< SCB AIRCR: VECTRESET Position */
+#define SCB_AIRCR_VECTRESET_Msk (1ul << SCB_AIRCR_VECTRESET_Pos) /*!< SCB AIRCR: VECTRESET Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos 4 /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk (1ul << SCB_SCR_SEVONPEND_Pos) /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos 2 /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk (1ul << SCB_SCR_SLEEPDEEP_Pos) /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos 1 /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk (1ul << SCB_SCR_SLEEPONEXIT_Pos) /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos 9 /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk (1ul << SCB_CCR_STKALIGN_Pos) /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_BFHFNMIGN_Pos 8 /*!< SCB CCR: BFHFNMIGN Position */
+#define SCB_CCR_BFHFNMIGN_Msk (1ul << SCB_CCR_BFHFNMIGN_Pos) /*!< SCB CCR: BFHFNMIGN Mask */
+
+#define SCB_CCR_DIV_0_TRP_Pos 4 /*!< SCB CCR: DIV_0_TRP Position */
+#define SCB_CCR_DIV_0_TRP_Msk (1ul << SCB_CCR_DIV_0_TRP_Pos) /*!< SCB CCR: DIV_0_TRP Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos 3 /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk (1ul << SCB_CCR_UNALIGN_TRP_Pos) /*!< SCB CCR: UNALIGN_TRP Mask */
+
+#define SCB_CCR_USERSETMPEND_Pos 1 /*!< SCB CCR: USERSETMPEND Position */
+#define SCB_CCR_USERSETMPEND_Msk (1ul << SCB_CCR_USERSETMPEND_Pos) /*!< SCB CCR: USERSETMPEND Mask */
+
+#define SCB_CCR_NONBASETHRDENA_Pos 0 /*!< SCB CCR: NONBASETHRDENA Position */
+#define SCB_CCR_NONBASETHRDENA_Msk (1ul << SCB_CCR_NONBASETHRDENA_Pos) /*!< SCB CCR: NONBASETHRDENA Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_USGFAULTENA_Pos 18 /*!< SCB SHCSR: USGFAULTENA Position */
+#define SCB_SHCSR_USGFAULTENA_Msk (1ul << SCB_SHCSR_USGFAULTENA_Pos) /*!< SCB SHCSR: USGFAULTENA Mask */
+
+#define SCB_SHCSR_BUSFAULTENA_Pos 17 /*!< SCB SHCSR: BUSFAULTENA Position */
+#define SCB_SHCSR_BUSFAULTENA_Msk (1ul << SCB_SHCSR_BUSFAULTENA_Pos) /*!< SCB SHCSR: BUSFAULTENA Mask */
+
+#define SCB_SHCSR_MEMFAULTENA_Pos 16 /*!< SCB SHCSR: MEMFAULTENA Position */
+#define SCB_SHCSR_MEMFAULTENA_Msk (1ul << SCB_SHCSR_MEMFAULTENA_Pos) /*!< SCB SHCSR: MEMFAULTENA Mask */
+
+#define SCB_SHCSR_SVCALLPENDED_Pos 15 /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk (1ul << SCB_SHCSR_SVCALLPENDED_Pos) /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+#define SCB_SHCSR_BUSFAULTPENDED_Pos 14 /*!< SCB SHCSR: BUSFAULTPENDED Position */
+#define SCB_SHCSR_BUSFAULTPENDED_Msk (1ul << SCB_SHCSR_BUSFAULTPENDED_Pos) /*!< SCB SHCSR: BUSFAULTPENDED Mask */
+
+#define SCB_SHCSR_MEMFAULTPENDED_Pos 13 /*!< SCB SHCSR: MEMFAULTPENDED Position */
+#define SCB_SHCSR_MEMFAULTPENDED_Msk (1ul << SCB_SHCSR_MEMFAULTPENDED_Pos) /*!< SCB SHCSR: MEMFAULTPENDED Mask */
+
+#define SCB_SHCSR_USGFAULTPENDED_Pos 12 /*!< SCB SHCSR: USGFAULTPENDED Position */
+#define SCB_SHCSR_USGFAULTPENDED_Msk (1ul << SCB_SHCSR_USGFAULTPENDED_Pos) /*!< SCB SHCSR: USGFAULTPENDED Mask */
+
+#define SCB_SHCSR_SYSTICKACT_Pos 11 /*!< SCB SHCSR: SYSTICKACT Position */
+#define SCB_SHCSR_SYSTICKACT_Msk (1ul << SCB_SHCSR_SYSTICKACT_Pos) /*!< SCB SHCSR: SYSTICKACT Mask */
+
+#define SCB_SHCSR_PENDSVACT_Pos 10 /*!< SCB SHCSR: PENDSVACT Position */
+#define SCB_SHCSR_PENDSVACT_Msk (1ul << SCB_SHCSR_PENDSVACT_Pos) /*!< SCB SHCSR: PENDSVACT Mask */
+
+#define SCB_SHCSR_MONITORACT_Pos 8 /*!< SCB SHCSR: MONITORACT Position */
+#define SCB_SHCSR_MONITORACT_Msk (1ul << SCB_SHCSR_MONITORACT_Pos) /*!< SCB SHCSR: MONITORACT Mask */
+
+#define SCB_SHCSR_SVCALLACT_Pos 7 /*!< SCB SHCSR: SVCALLACT Position */
+#define SCB_SHCSR_SVCALLACT_Msk (1ul << SCB_SHCSR_SVCALLACT_Pos) /*!< SCB SHCSR: SVCALLACT Mask */
+
+#define SCB_SHCSR_USGFAULTACT_Pos 3 /*!< SCB SHCSR: USGFAULTACT Position */
+#define SCB_SHCSR_USGFAULTACT_Msk (1ul << SCB_SHCSR_USGFAULTACT_Pos) /*!< SCB SHCSR: USGFAULTACT Mask */
+
+#define SCB_SHCSR_BUSFAULTACT_Pos 1 /*!< SCB SHCSR: BUSFAULTACT Position */
+#define SCB_SHCSR_BUSFAULTACT_Msk (1ul << SCB_SHCSR_BUSFAULTACT_Pos) /*!< SCB SHCSR: BUSFAULTACT Mask */
+
+#define SCB_SHCSR_MEMFAULTACT_Pos 0 /*!< SCB SHCSR: MEMFAULTACT Position */
+#define SCB_SHCSR_MEMFAULTACT_Msk (1ul << SCB_SHCSR_MEMFAULTACT_Pos) /*!< SCB SHCSR: MEMFAULTACT Mask */
+
+/* SCB Configurable Fault Status Registers Definitions */
+#define SCB_CFSR_USGFAULTSR_Pos 16 /*!< SCB CFSR: Usage Fault Status Register Position */
+#define SCB_CFSR_USGFAULTSR_Msk (0xFFFFul << SCB_CFSR_USGFAULTSR_Pos) /*!< SCB CFSR: Usage Fault Status Register Mask */
+
+#define SCB_CFSR_BUSFAULTSR_Pos 8 /*!< SCB CFSR: Bus Fault Status Register Position */
+#define SCB_CFSR_BUSFAULTSR_Msk (0xFFul << SCB_CFSR_BUSFAULTSR_Pos) /*!< SCB CFSR: Bus Fault Status Register Mask */
+
+#define SCB_CFSR_MEMFAULTSR_Pos 0 /*!< SCB CFSR: Memory Manage Fault Status Register Position */
+#define SCB_CFSR_MEMFAULTSR_Msk (0xFFul << SCB_CFSR_MEMFAULTSR_Pos) /*!< SCB CFSR: Memory Manage Fault Status Register Mask */
+
+/* SCB Hard Fault Status Registers Definitions */
+#define SCB_HFSR_DEBUGEVT_Pos 31 /*!< SCB HFSR: DEBUGEVT Position */
+#define SCB_HFSR_DEBUGEVT_Msk (1ul << SCB_HFSR_DEBUGEVT_Pos) /*!< SCB HFSR: DEBUGEVT Mask */
+
+#define SCB_HFSR_FORCED_Pos 30 /*!< SCB HFSR: FORCED Position */
+#define SCB_HFSR_FORCED_Msk (1ul << SCB_HFSR_FORCED_Pos) /*!< SCB HFSR: FORCED Mask */
+
+#define SCB_HFSR_VECTTBL_Pos 1 /*!< SCB HFSR: VECTTBL Position */
+#define SCB_HFSR_VECTTBL_Msk (1ul << SCB_HFSR_VECTTBL_Pos) /*!< SCB HFSR: VECTTBL Mask */
+
+/* SCB Debug Fault Status Register Definitions */
+#define SCB_DFSR_EXTERNAL_Pos 4 /*!< SCB DFSR: EXTERNAL Position */
+#define SCB_DFSR_EXTERNAL_Msk (1ul << SCB_DFSR_EXTERNAL_Pos) /*!< SCB DFSR: EXTERNAL Mask */
+
+#define SCB_DFSR_VCATCH_Pos 3 /*!< SCB DFSR: VCATCH Position */
+#define SCB_DFSR_VCATCH_Msk (1ul << SCB_DFSR_VCATCH_Pos) /*!< SCB DFSR: VCATCH Mask */
+
+#define SCB_DFSR_DWTTRAP_Pos 2 /*!< SCB DFSR: DWTTRAP Position */
+#define SCB_DFSR_DWTTRAP_Msk (1ul << SCB_DFSR_DWTTRAP_Pos) /*!< SCB DFSR: DWTTRAP Mask */
+
+#define SCB_DFSR_BKPT_Pos 1 /*!< SCB DFSR: BKPT Position */
+#define SCB_DFSR_BKPT_Msk (1ul << SCB_DFSR_BKPT_Pos) /*!< SCB DFSR: BKPT Mask */
+
+#define SCB_DFSR_HALTED_Pos 0 /*!< SCB DFSR: HALTED Position */
+#define SCB_DFSR_HALTED_Msk (1ul << SCB_DFSR_HALTED_Pos) /*!< SCB DFSR: HALTED Mask */
+/*@}*/ /* end of group CMSIS_CM3_SCB */
+
+
+/** @addtogroup CMSIS_CM3_SysTick CMSIS CM3 SysTick
+ memory mapped structure for SysTick
+ @{
+ */
+typedef struct
+{
+ __IO uint32_t CTRL; /*!< Offset: 0x00 SysTick Control and Status Register */
+ __IO uint32_t LOAD; /*!< Offset: 0x04 SysTick Reload Value Register */
+ __IO uint32_t VAL; /*!< Offset: 0x08 SysTick Current Value Register */
+ __I uint32_t CALIB; /*!< Offset: 0x0C SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos 16 /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk (1ul << SysTick_CTRL_COUNTFLAG_Pos) /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos 2 /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk (1ul << SysTick_CTRL_CLKSOURCE_Pos) /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos 1 /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk (1ul << SysTick_CTRL_TICKINT_Pos) /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos 0 /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk (1ul << SysTick_CTRL_ENABLE_Pos) /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos 0 /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk (0xFFFFFFul << SysTick_LOAD_RELOAD_Pos) /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos 0 /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk (0xFFFFFFul << SysTick_VAL_CURRENT_Pos) /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos 31 /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk (1ul << SysTick_CALIB_NOREF_Pos) /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos 30 /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk (1ul << SysTick_CALIB_SKEW_Pos) /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos 0 /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk (0xFFFFFFul << SysTick_VAL_CURRENT_Pos) /*!< SysTick CALIB: TENMS Mask */
+/*@}*/ /* end of group CMSIS_CM3_SysTick */
+
+
+/** @addtogroup CMSIS_CM3_ITM CMSIS CM3 ITM
+ memory mapped structure for Instrumentation Trace Macrocell (ITM)
+ @{
+ */
+typedef struct
+{
+ __O union
+ {
+ __O uint8_t u8; /*!< Offset: ITM Stimulus Port 8-bit */
+ __O uint16_t u16; /*!< Offset: ITM Stimulus Port 16-bit */
+ __O uint32_t u32; /*!< Offset: ITM Stimulus Port 32-bit */
+ } PORT [32]; /*!< Offset: 0x00 ITM Stimulus Port Registers */
+ uint32_t RESERVED0[864];
+ __IO uint32_t TER; /*!< Offset: ITM Trace Enable Register */
+ uint32_t RESERVED1[15];
+ __IO uint32_t TPR; /*!< Offset: ITM Trace Privilege Register */
+ uint32_t RESERVED2[15];
+ __IO uint32_t TCR; /*!< Offset: ITM Trace Control Register */
+ uint32_t RESERVED3[29];
+ __IO uint32_t IWR; /*!< Offset: ITM Integration Write Register */
+ __IO uint32_t IRR; /*!< Offset: ITM Integration Read Register */
+ __IO uint32_t IMCR; /*!< Offset: ITM Integration Mode Control Register */
+ uint32_t RESERVED4[43];
+ __IO uint32_t LAR; /*!< Offset: ITM Lock Access Register */
+ __IO uint32_t LSR; /*!< Offset: ITM Lock Status Register */
+ uint32_t RESERVED5[6];
+ __I uint32_t PID4; /*!< Offset: ITM Peripheral Identification Register #4 */
+ __I uint32_t PID5; /*!< Offset: ITM Peripheral Identification Register #5 */
+ __I uint32_t PID6; /*!< Offset: ITM Peripheral Identification Register #6 */
+ __I uint32_t PID7; /*!< Offset: ITM Peripheral Identification Register #7 */
+ __I uint32_t PID0; /*!< Offset: ITM Peripheral Identification Register #0 */
+ __I uint32_t PID1; /*!< Offset: ITM Peripheral Identification Register #1 */
+ __I uint32_t PID2; /*!< Offset: ITM Peripheral Identification Register #2 */
+ __I uint32_t PID3; /*!< Offset: ITM Peripheral Identification Register #3 */
+ __I uint32_t CID0; /*!< Offset: ITM Component Identification Register #0 */
+ __I uint32_t CID1; /*!< Offset: ITM Component Identification Register #1 */
+ __I uint32_t CID2; /*!< Offset: ITM Component Identification Register #2 */
+ __I uint32_t CID3; /*!< Offset: ITM Component Identification Register #3 */
+} ITM_Type;
+
+/* ITM Trace Privilege Register Definitions */
+#define ITM_TPR_PRIVMASK_Pos 0 /*!< ITM TPR: PRIVMASK Position */
+#define ITM_TPR_PRIVMASK_Msk (0xFul << ITM_TPR_PRIVMASK_Pos) /*!< ITM TPR: PRIVMASK Mask */
+
+/* ITM Trace Control Register Definitions */
+#define ITM_TCR_BUSY_Pos 23 /*!< ITM TCR: BUSY Position */
+#define ITM_TCR_BUSY_Msk (1ul << ITM_TCR_BUSY_Pos) /*!< ITM TCR: BUSY Mask */
+
+#define ITM_TCR_ATBID_Pos 16 /*!< ITM TCR: ATBID Position */
+#define ITM_TCR_ATBID_Msk (0x7Ful << ITM_TCR_ATBID_Pos) /*!< ITM TCR: ATBID Mask */
+
+#define ITM_TCR_TSPrescale_Pos 8 /*!< ITM TCR: TSPrescale Position */
+#define ITM_TCR_TSPrescale_Msk (3ul << ITM_TCR_TSPrescale_Pos) /*!< ITM TCR: TSPrescale Mask */
+
+#define ITM_TCR_SWOENA_Pos 4 /*!< ITM TCR: SWOENA Position */
+#define ITM_TCR_SWOENA_Msk (1ul << ITM_TCR_SWOENA_Pos) /*!< ITM TCR: SWOENA Mask */
+
+#define ITM_TCR_DWTENA_Pos 3 /*!< ITM TCR: DWTENA Position */
+#define ITM_TCR_DWTENA_Msk (1ul << ITM_TCR_DWTENA_Pos) /*!< ITM TCR: DWTENA Mask */
+
+#define ITM_TCR_SYNCENA_Pos 2 /*!< ITM TCR: SYNCENA Position */
+#define ITM_TCR_SYNCENA_Msk (1ul << ITM_TCR_SYNCENA_Pos) /*!< ITM TCR: SYNCENA Mask */
+
+#define ITM_TCR_TSENA_Pos 1 /*!< ITM TCR: TSENA Position */
+#define ITM_TCR_TSENA_Msk (1ul << ITM_TCR_TSENA_Pos) /*!< ITM TCR: TSENA Mask */
+
+#define ITM_TCR_ITMENA_Pos 0 /*!< ITM TCR: ITM Enable bit Position */
+#define ITM_TCR_ITMENA_Msk (1ul << ITM_TCR_ITMENA_Pos) /*!< ITM TCR: ITM Enable bit Mask */
+
+/* ITM Integration Write Register Definitions */
+#define ITM_IWR_ATVALIDM_Pos 0 /*!< ITM IWR: ATVALIDM Position */
+#define ITM_IWR_ATVALIDM_Msk (1ul << ITM_IWR_ATVALIDM_Pos) /*!< ITM IWR: ATVALIDM Mask */
+
+/* ITM Integration Read Register Definitions */
+#define ITM_IRR_ATREADYM_Pos 0 /*!< ITM IRR: ATREADYM Position */
+#define ITM_IRR_ATREADYM_Msk (1ul << ITM_IRR_ATREADYM_Pos) /*!< ITM IRR: ATREADYM Mask */
+
+/* ITM Integration Mode Control Register Definitions */
+#define ITM_IMCR_INTEGRATION_Pos 0 /*!< ITM IMCR: INTEGRATION Position */
+#define ITM_IMCR_INTEGRATION_Msk (1ul << ITM_IMCR_INTEGRATION_Pos) /*!< ITM IMCR: INTEGRATION Mask */
+
+/* ITM Lock Status Register Definitions */
+#define ITM_LSR_ByteAcc_Pos 2 /*!< ITM LSR: ByteAcc Position */
+#define ITM_LSR_ByteAcc_Msk (1ul << ITM_LSR_ByteAcc_Pos) /*!< ITM LSR: ByteAcc Mask */
+
+#define ITM_LSR_Access_Pos 1 /*!< ITM LSR: Access Position */
+#define ITM_LSR_Access_Msk (1ul << ITM_LSR_Access_Pos) /*!< ITM LSR: Access Mask */
+
+#define ITM_LSR_Present_Pos 0 /*!< ITM LSR: Present Position */
+#define ITM_LSR_Present_Msk (1ul << ITM_LSR_Present_Pos) /*!< ITM LSR: Present Mask */
+/*@}*/ /* end of group CMSIS_CM3_ITM */
+
+
+/** @addtogroup CMSIS_CM3_InterruptType CMSIS CM3 Interrupt Type
+ memory mapped structure for Interrupt Type
+ @{
+ */
+typedef struct
+{
+ uint32_t RESERVED0;
+ __I uint32_t ICTR; /*!< Offset: 0x04 Interrupt Control Type Register */
+#if ((defined __CM3_REV) && (__CM3_REV >= 0x200))
+ __IO uint32_t ACTLR; /*!< Offset: 0x08 Auxiliary Control Register */
+#else
+ uint32_t RESERVED1;
+#endif
+} InterruptType_Type;
+
+/* Interrupt Controller Type Register Definitions */
+#define InterruptType_ICTR_INTLINESNUM_Pos 0 /*!< InterruptType ICTR: INTLINESNUM Position */
+#define InterruptType_ICTR_INTLINESNUM_Msk (0x1Ful << InterruptType_ICTR_INTLINESNUM_Pos) /*!< InterruptType ICTR: INTLINESNUM Mask */
+
+/* Auxiliary Control Register Definitions */
+#define InterruptType_ACTLR_DISFOLD_Pos 2 /*!< InterruptType ACTLR: DISFOLD Position */
+#define InterruptType_ACTLR_DISFOLD_Msk (1ul << InterruptType_ACTLR_DISFOLD_Pos) /*!< InterruptType ACTLR: DISFOLD Mask */
+
+#define InterruptType_ACTLR_DISDEFWBUF_Pos 1 /*!< InterruptType ACTLR: DISDEFWBUF Position */
+#define InterruptType_ACTLR_DISDEFWBUF_Msk (1ul << InterruptType_ACTLR_DISDEFWBUF_Pos) /*!< InterruptType ACTLR: DISDEFWBUF Mask */
+
+#define InterruptType_ACTLR_DISMCYCINT_Pos 0 /*!< InterruptType ACTLR: DISMCYCINT Position */
+#define InterruptType_ACTLR_DISMCYCINT_Msk (1ul << InterruptType_ACTLR_DISMCYCINT_Pos) /*!< InterruptType ACTLR: DISMCYCINT Mask */
+/*@}*/ /* end of group CMSIS_CM3_InterruptType */
+
+
+#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1)
+/** @addtogroup CMSIS_CM3_MPU CMSIS CM3 MPU
+ memory mapped structure for Memory Protection Unit (MPU)
+ @{
+ */
+typedef struct
+{
+ __I uint32_t TYPE; /*!< Offset: 0x00 MPU Type Register */
+ __IO uint32_t CTRL; /*!< Offset: 0x04 MPU Control Register */
+ __IO uint32_t RNR; /*!< Offset: 0x08 MPU Region RNRber Register */
+ __IO uint32_t RBAR; /*!< Offset: 0x0C MPU Region Base Address Register */
+ __IO uint32_t RASR; /*!< Offset: 0x10 MPU Region Attribute and Size Register */
+ __IO uint32_t RBAR_A1; /*!< Offset: 0x14 MPU Alias 1 Region Base Address Register */
+ __IO uint32_t RASR_A1; /*!< Offset: 0x18 MPU Alias 1 Region Attribute and Size Register */
+ __IO uint32_t RBAR_A2; /*!< Offset: 0x1C MPU Alias 2 Region Base Address Register */
+ __IO uint32_t RASR_A2; /*!< Offset: 0x20 MPU Alias 2 Region Attribute and Size Register */
+ __IO uint32_t RBAR_A3; /*!< Offset: 0x24 MPU Alias 3 Region Base Address Register */
+ __IO uint32_t RASR_A3; /*!< Offset: 0x28 MPU Alias 3 Region Attribute and Size Register */
+} MPU_Type;
+
+/* MPU Type Register */
+#define MPU_TYPE_IREGION_Pos 16 /*!< MPU TYPE: IREGION Position */
+#define MPU_TYPE_IREGION_Msk (0xFFul << MPU_TYPE_IREGION_Pos) /*!< MPU TYPE: IREGION Mask */
+
+#define MPU_TYPE_DREGION_Pos 8 /*!< MPU TYPE: DREGION Position */
+#define MPU_TYPE_DREGION_Msk (0xFFul << MPU_TYPE_DREGION_Pos) /*!< MPU TYPE: DREGION Mask */
+
+#define MPU_TYPE_SEPARATE_Pos 0 /*!< MPU TYPE: SEPARATE Position */
+#define MPU_TYPE_SEPARATE_Msk (1ul << MPU_TYPE_SEPARATE_Pos) /*!< MPU TYPE: SEPARATE Mask */
+
+/* MPU Control Register */
+#define MPU_CTRL_PRIVDEFENA_Pos 2 /*!< MPU CTRL: PRIVDEFENA Position */
+#define MPU_CTRL_PRIVDEFENA_Msk (1ul << MPU_CTRL_PRIVDEFENA_Pos) /*!< MPU CTRL: PRIVDEFENA Mask */
+
+#define MPU_CTRL_HFNMIENA_Pos 1 /*!< MPU CTRL: HFNMIENA Position */
+#define MPU_CTRL_HFNMIENA_Msk (1ul << MPU_CTRL_HFNMIENA_Pos) /*!< MPU CTRL: HFNMIENA Mask */
+
+#define MPU_CTRL_ENABLE_Pos 0 /*!< MPU CTRL: ENABLE Position */
+#define MPU_CTRL_ENABLE_Msk (1ul << MPU_CTRL_ENABLE_Pos) /*!< MPU CTRL: ENABLE Mask */
+
+/* MPU Region Number Register */
+#define MPU_RNR_REGION_Pos 0 /*!< MPU RNR: REGION Position */
+#define MPU_RNR_REGION_Msk (0xFFul << MPU_RNR_REGION_Pos) /*!< MPU RNR: REGION Mask */
+
+/* MPU Region Base Address Register */
+#define MPU_RBAR_ADDR_Pos 5 /*!< MPU RBAR: ADDR Position */
+#define MPU_RBAR_ADDR_Msk (0x7FFFFFFul << MPU_RBAR_ADDR_Pos) /*!< MPU RBAR: ADDR Mask */
+
+#define MPU_RBAR_VALID_Pos 4 /*!< MPU RBAR: VALID Position */
+#define MPU_RBAR_VALID_Msk (1ul << MPU_RBAR_VALID_Pos) /*!< MPU RBAR: VALID Mask */
+
+#define MPU_RBAR_REGION_Pos 0 /*!< MPU RBAR: REGION Position */
+#define MPU_RBAR_REGION_Msk (0xFul << MPU_RBAR_REGION_Pos) /*!< MPU RBAR: REGION Mask */
+
+/* MPU Region Attribute and Size Register */
+#define MPU_RASR_XN_Pos 28 /*!< MPU RASR: XN Position */
+#define MPU_RASR_XN_Msk (1ul << MPU_RASR_XN_Pos) /*!< MPU RASR: XN Mask */
+
+#define MPU_RASR_AP_Pos 24 /*!< MPU RASR: AP Position */
+#define MPU_RASR_AP_Msk (7ul << MPU_RASR_AP_Pos) /*!< MPU RASR: AP Mask */
+
+#define MPU_RASR_TEX_Pos 19 /*!< MPU RASR: TEX Position */
+#define MPU_RASR_TEX_Msk (7ul << MPU_RASR_TEX_Pos) /*!< MPU RASR: TEX Mask */
+
+#define MPU_RASR_S_Pos 18 /*!< MPU RASR: Shareable bit Position */
+#define MPU_RASR_S_Msk (1ul << MPU_RASR_S_Pos) /*!< MPU RASR: Shareable bit Mask */
+
+#define MPU_RASR_C_Pos 17 /*!< MPU RASR: Cacheable bit Position */
+#define MPU_RASR_C_Msk (1ul << MPU_RASR_C_Pos) /*!< MPU RASR: Cacheable bit Mask */
+
+#define MPU_RASR_B_Pos 16 /*!< MPU RASR: Bufferable bit Position */
+#define MPU_RASR_B_Msk (1ul << MPU_RASR_B_Pos) /*!< MPU RASR: Bufferable bit Mask */
+
+#define MPU_RASR_SRD_Pos 8 /*!< MPU RASR: Sub-Region Disable Position */
+#define MPU_RASR_SRD_Msk (0xFFul << MPU_RASR_SRD_Pos) /*!< MPU RASR: Sub-Region Disable Mask */
+
+#define MPU_RASR_SIZE_Pos 1 /*!< MPU RASR: Region Size Field Position */
+#define MPU_RASR_SIZE_Msk (0x1Ful << MPU_RASR_SIZE_Pos) /*!< MPU RASR: Region Size Field Mask */
+
+#define MPU_RASR_ENA_Pos 0 /*!< MPU RASR: Region enable bit Position */
+#define MPU_RASR_ENA_Msk (0x1Ful << MPU_RASR_ENA_Pos) /*!< MPU RASR: Region enable bit Disable Mask */
+
+/*@}*/ /* end of group CMSIS_CM3_MPU */
+#endif
+
+
+/** @addtogroup CMSIS_CM3_CoreDebug CMSIS CM3 Core Debug
+ memory mapped structure for Core Debug Register
+ @{
+ */
+typedef struct
+{
+ __IO uint32_t DHCSR; /*!< Offset: 0x00 Debug Halting Control and Status Register */
+ __O uint32_t DCRSR; /*!< Offset: 0x04 Debug Core Register Selector Register */
+ __IO uint32_t DCRDR; /*!< Offset: 0x08 Debug Core Register Data Register */
+ __IO uint32_t DEMCR; /*!< Offset: 0x0C Debug Exception and Monitor Control Register */
+} CoreDebug_Type;
+
+/* Debug Halting Control and Status Register */
+#define CoreDebug_DHCSR_DBGKEY_Pos 16 /*!< CoreDebug DHCSR: DBGKEY Position */
+#define CoreDebug_DHCSR_DBGKEY_Msk (0xFFFFul << CoreDebug_DHCSR_DBGKEY_Pos) /*!< CoreDebug DHCSR: DBGKEY Mask */
+
+#define CoreDebug_DHCSR_S_RESET_ST_Pos 25 /*!< CoreDebug DHCSR: S_RESET_ST Position */
+#define CoreDebug_DHCSR_S_RESET_ST_Msk (1ul << CoreDebug_DHCSR_S_RESET_ST_Pos) /*!< CoreDebug DHCSR: S_RESET_ST Mask */
+
+#define CoreDebug_DHCSR_S_RETIRE_ST_Pos 24 /*!< CoreDebug DHCSR: S_RETIRE_ST Position */
+#define CoreDebug_DHCSR_S_RETIRE_ST_Msk (1ul << CoreDebug_DHCSR_S_RETIRE_ST_Pos) /*!< CoreDebug DHCSR: S_RETIRE_ST Mask */
+
+#define CoreDebug_DHCSR_S_LOCKUP_Pos 19 /*!< CoreDebug DHCSR: S_LOCKUP Position */
+#define CoreDebug_DHCSR_S_LOCKUP_Msk (1ul << CoreDebug_DHCSR_S_LOCKUP_Pos) /*!< CoreDebug DHCSR: S_LOCKUP Mask */
+
+#define CoreDebug_DHCSR_S_SLEEP_Pos 18 /*!< CoreDebug DHCSR: S_SLEEP Position */
+#define CoreDebug_DHCSR_S_SLEEP_Msk (1ul << CoreDebug_DHCSR_S_SLEEP_Pos) /*!< CoreDebug DHCSR: S_SLEEP Mask */
+
+#define CoreDebug_DHCSR_S_HALT_Pos 17 /*!< CoreDebug DHCSR: S_HALT Position */
+#define CoreDebug_DHCSR_S_HALT_Msk (1ul << CoreDebug_DHCSR_S_HALT_Pos) /*!< CoreDebug DHCSR: S_HALT Mask */
+
+#define CoreDebug_DHCSR_S_REGRDY_Pos 16 /*!< CoreDebug DHCSR: S_REGRDY Position */
+#define CoreDebug_DHCSR_S_REGRDY_Msk (1ul << CoreDebug_DHCSR_S_REGRDY_Pos) /*!< CoreDebug DHCSR: S_REGRDY Mask */
+
+#define CoreDebug_DHCSR_C_SNAPSTALL_Pos 5 /*!< CoreDebug DHCSR: C_SNAPSTALL Position */
+#define CoreDebug_DHCSR_C_SNAPSTALL_Msk (1ul << CoreDebug_DHCSR_C_SNAPSTALL_Pos) /*!< CoreDebug DHCSR: C_SNAPSTALL Mask */
+
+#define CoreDebug_DHCSR_C_MASKINTS_Pos 3 /*!< CoreDebug DHCSR: C_MASKINTS Position */
+#define CoreDebug_DHCSR_C_MASKINTS_Msk (1ul << CoreDebug_DHCSR_C_MASKINTS_Pos) /*!< CoreDebug DHCSR: C_MASKINTS Mask */
+
+#define CoreDebug_DHCSR_C_STEP_Pos 2 /*!< CoreDebug DHCSR: C_STEP Position */
+#define CoreDebug_DHCSR_C_STEP_Msk (1ul << CoreDebug_DHCSR_C_STEP_Pos) /*!< CoreDebug DHCSR: C_STEP Mask */
+
+#define CoreDebug_DHCSR_C_HALT_Pos 1 /*!< CoreDebug DHCSR: C_HALT Position */
+#define CoreDebug_DHCSR_C_HALT_Msk (1ul << CoreDebug_DHCSR_C_HALT_Pos) /*!< CoreDebug DHCSR: C_HALT Mask */
+
+#define CoreDebug_DHCSR_C_DEBUGEN_Pos 0 /*!< CoreDebug DHCSR: C_DEBUGEN Position */
+#define CoreDebug_DHCSR_C_DEBUGEN_Msk (1ul << CoreDebug_DHCSR_C_DEBUGEN_Pos) /*!< CoreDebug DHCSR: C_DEBUGEN Mask */
+
+/* Debug Core Register Selector Register */
+#define CoreDebug_DCRSR_REGWnR_Pos 16 /*!< CoreDebug DCRSR: REGWnR Position */
+#define CoreDebug_DCRSR_REGWnR_Msk (1ul << CoreDebug_DCRSR_REGWnR_Pos) /*!< CoreDebug DCRSR: REGWnR Mask */
+
+#define CoreDebug_DCRSR_REGSEL_Pos 0 /*!< CoreDebug DCRSR: REGSEL Position */
+#define CoreDebug_DCRSR_REGSEL_Msk (0x1Ful << CoreDebug_DCRSR_REGSEL_Pos) /*!< CoreDebug DCRSR: REGSEL Mask */
+
+/* Debug Exception and Monitor Control Register */
+#define CoreDebug_DEMCR_TRCENA_Pos 24 /*!< CoreDebug DEMCR: TRCENA Position */
+#define CoreDebug_DEMCR_TRCENA_Msk (1ul << CoreDebug_DEMCR_TRCENA_Pos) /*!< CoreDebug DEMCR: TRCENA Mask */
+
+#define CoreDebug_DEMCR_MON_REQ_Pos 19 /*!< CoreDebug DEMCR: MON_REQ Position */
+#define CoreDebug_DEMCR_MON_REQ_Msk (1ul << CoreDebug_DEMCR_MON_REQ_Pos) /*!< CoreDebug DEMCR: MON_REQ Mask */
+
+#define CoreDebug_DEMCR_MON_STEP_Pos 18 /*!< CoreDebug DEMCR: MON_STEP Position */
+#define CoreDebug_DEMCR_MON_STEP_Msk (1ul << CoreDebug_DEMCR_MON_STEP_Pos) /*!< CoreDebug DEMCR: MON_STEP Mask */
+
+#define CoreDebug_DEMCR_MON_PEND_Pos 17 /*!< CoreDebug DEMCR: MON_PEND Position */
+#define CoreDebug_DEMCR_MON_PEND_Msk (1ul << CoreDebug_DEMCR_MON_PEND_Pos) /*!< CoreDebug DEMCR: MON_PEND Mask */
+
+#define CoreDebug_DEMCR_MON_EN_Pos 16 /*!< CoreDebug DEMCR: MON_EN Position */
+#define CoreDebug_DEMCR_MON_EN_Msk (1ul << CoreDebug_DEMCR_MON_EN_Pos) /*!< CoreDebug DEMCR: MON_EN Mask */
+
+#define CoreDebug_DEMCR_VC_HARDERR_Pos 10 /*!< CoreDebug DEMCR: VC_HARDERR Position */
+#define CoreDebug_DEMCR_VC_HARDERR_Msk (1ul << CoreDebug_DEMCR_VC_HARDERR_Pos) /*!< CoreDebug DEMCR: VC_HARDERR Mask */
+
+#define CoreDebug_DEMCR_VC_INTERR_Pos 9 /*!< CoreDebug DEMCR: VC_INTERR Position */
+#define CoreDebug_DEMCR_VC_INTERR_Msk (1ul << CoreDebug_DEMCR_VC_INTERR_Pos) /*!< CoreDebug DEMCR: VC_INTERR Mask */
+
+#define CoreDebug_DEMCR_VC_BUSERR_Pos 8 /*!< CoreDebug DEMCR: VC_BUSERR Position */
+#define CoreDebug_DEMCR_VC_BUSERR_Msk (1ul << CoreDebug_DEMCR_VC_BUSERR_Pos) /*!< CoreDebug DEMCR: VC_BUSERR Mask */
+
+#define CoreDebug_DEMCR_VC_STATERR_Pos 7 /*!< CoreDebug DEMCR: VC_STATERR Position */
+#define CoreDebug_DEMCR_VC_STATERR_Msk (1ul << CoreDebug_DEMCR_VC_STATERR_Pos) /*!< CoreDebug DEMCR: VC_STATERR Mask */
+
+#define CoreDebug_DEMCR_VC_CHKERR_Pos 6 /*!< CoreDebug DEMCR: VC_CHKERR Position */
+#define CoreDebug_DEMCR_VC_CHKERR_Msk (1ul << CoreDebug_DEMCR_VC_CHKERR_Pos) /*!< CoreDebug DEMCR: VC_CHKERR Mask */
+
+#define CoreDebug_DEMCR_VC_NOCPERR_Pos 5 /*!< CoreDebug DEMCR: VC_NOCPERR Position */
+#define CoreDebug_DEMCR_VC_NOCPERR_Msk (1ul << CoreDebug_DEMCR_VC_NOCPERR_Pos) /*!< CoreDebug DEMCR: VC_NOCPERR Mask */
+
+#define CoreDebug_DEMCR_VC_MMERR_Pos 4 /*!< CoreDebug DEMCR: VC_MMERR Position */
+#define CoreDebug_DEMCR_VC_MMERR_Msk (1ul << CoreDebug_DEMCR_VC_MMERR_Pos) /*!< CoreDebug DEMCR: VC_MMERR Mask */
+
+#define CoreDebug_DEMCR_VC_CORERESET_Pos 0 /*!< CoreDebug DEMCR: VC_CORERESET Position */
+#define CoreDebug_DEMCR_VC_CORERESET_Msk (1ul << CoreDebug_DEMCR_VC_CORERESET_Pos) /*!< CoreDebug DEMCR: VC_CORERESET Mask */
+/*@}*/ /* end of group CMSIS_CM3_CoreDebug */
+
+
+/* Memory mapping of Cortex-M3 Hardware */
+#define SCS_BASE (0xE000E000) /*!< System Control Space Base Address */
+#define ITM_BASE (0xE0000000) /*!< ITM Base Address */
+#define CoreDebug_BASE (0xE000EDF0) /*!< Core Debug Base Address */
+#define SysTick_BASE (SCS_BASE + 0x0010) /*!< SysTick Base Address */
+#define NVIC_BASE (SCS_BASE + 0x0100) /*!< NVIC Base Address */
+#define SCB_BASE (SCS_BASE + 0x0D00) /*!< System Control Block Base Address */
+
+#define InterruptType ((InterruptType_Type *) SCS_BASE) /*!< Interrupt Type Register */
+#define SCB ((SCB_Type *) SCB_BASE) /*!< SCB configuration struct */
+#define SysTick ((SysTick_Type *) SysTick_BASE) /*!< SysTick configuration struct */
+#define NVIC ((NVIC_Type *) NVIC_BASE) /*!< NVIC configuration struct */
+#define ITM ((ITM_Type *) ITM_BASE) /*!< ITM configuration struct */
+#define CoreDebug ((CoreDebug_Type *) CoreDebug_BASE) /*!< Core Debug configuration struct */
+
+#if defined (__MPU_PRESENT) && (__MPU_PRESENT == 1)
+ #define MPU_BASE (SCS_BASE + 0x0D90) /*!< Memory Protection Unit */
+ #define MPU ((MPU_Type*) MPU_BASE) /*!< Memory Protection Unit */
+#endif
+
+/*@}*/ /* end of group CMSIS_CM3_core_register */
+
+
+/*******************************************************************************
+ * Hardware Abstraction Layer
+ ******************************************************************************/
+
+#if defined ( __CC_ARM )
+ #define __ASM __asm /*!< asm keyword for ARM Compiler */
+ #define __INLINE __inline /*!< inline keyword for ARM Compiler */
+
+#elif defined ( __ICCARM__ )
+ #define __ASM __asm /*!< asm keyword for IAR Compiler */
+ #define __INLINE inline /*!< inline keyword for IAR Compiler. Only avaiable in High optimization mode! */
+
+#elif defined ( __GNUC__ )
+ #define __ASM __asm /*!< asm keyword for GNU Compiler */
+ #define __INLINE inline /*!< inline keyword for GNU Compiler */
+
+#elif defined ( __TASKING__ )
+ #define __ASM __asm /*!< asm keyword for TASKING Compiler */
+ #define __INLINE inline /*!< inline keyword for TASKING Compiler */
+
+#endif
+
+
+/* ################### Compiler specific Intrinsics ########################### */
+
+#if defined ( __CC_ARM ) /*------------------RealView Compiler -----------------*/
+/* ARM armcc specific functions */
+
+#define __enable_fault_irq __enable_fiq
+#define __disable_fault_irq __disable_fiq
+
+#define __NOP __nop
+#define __WFI __wfi
+#define __WFE __wfe
+#define __SEV __sev
+#define __ISB() __isb(0)
+#define __DSB() __dsb(0)
+#define __DMB() __dmb(0)
+#define __REV __rev
+#define __RBIT __rbit
+#define __LDREXB(ptr) ((unsigned char ) __ldrex(ptr))
+#define __LDREXH(ptr) ((unsigned short) __ldrex(ptr))
+#define __LDREXW(ptr) ((unsigned int ) __ldrex(ptr))
+#define __STREXB(value, ptr) __strex(value, ptr)
+#define __STREXH(value, ptr) __strex(value, ptr)
+#define __STREXW(value, ptr) __strex(value, ptr)
+
+
+/* intrinsic unsigned long long __ldrexd(volatile void *ptr) */
+/* intrinsic int __strexd(unsigned long long val, volatile void *ptr) */
+/* intrinsic void __enable_irq(); */
+/* intrinsic void __disable_irq(); */
+
+
+/**
+ * @brief Return the Process Stack Pointer
+ *
+ * @return ProcessStackPointer
+ *
+ * Return the actual process stack pointer
+ */
+extern uint32_t __get_PSP(void);
+
+/**
+ * @brief Set the Process Stack Pointer
+ *
+ * @param topOfProcStack Process Stack Pointer
+ *
+ * Assign the value ProcessStackPointer to the MSP
+ * (process stack pointer) Cortex processor register
+ */
+extern void __set_PSP(uint32_t topOfProcStack);
+
+/**
+ * @brief Return the Main Stack Pointer
+ *
+ * @return Main Stack Pointer
+ *
+ * Return the current value of the MSP (main stack pointer)
+ * Cortex processor register
+ */
+extern uint32_t __get_MSP(void);
+
+/**
+ * @brief Set the Main Stack Pointer
+ *
+ * @param topOfMainStack Main Stack Pointer
+ *
+ * Assign the value mainStackPointer to the MSP
+ * (main stack pointer) Cortex processor register
+ */
+extern void __set_MSP(uint32_t topOfMainStack);
+
+/**
+ * @brief Reverse byte order in unsigned short value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in unsigned short value
+ */
+extern uint32_t __REV16(uint16_t value);
+
+/**
+ * @brief Reverse byte order in signed short value with sign extension to integer
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in signed short value with sign extension to integer
+ */
+extern int32_t __REVSH(int16_t value);
+
+
+#if (__ARMCC_VERSION < 400000)
+
+/**
+ * @brief Remove the exclusive lock created by ldrex
+ *
+ * Removes the exclusive lock which is created by ldrex.
+ */
+extern void __CLREX(void);
+
+/**
+ * @brief Return the Base Priority value
+ *
+ * @return BasePriority
+ *
+ * Return the content of the base priority register
+ */
+extern uint32_t __get_BASEPRI(void);
+
+/**
+ * @brief Set the Base Priority value
+ *
+ * @param basePri BasePriority
+ *
+ * Set the base priority register
+ */
+extern void __set_BASEPRI(uint32_t basePri);
+
+/**
+ * @brief Return the Priority Mask value
+ *
+ * @return PriMask
+ *
+ * Return state of the priority mask bit from the priority mask register
+ */
+extern uint32_t __get_PRIMASK(void);
+
+/**
+ * @brief Set the Priority Mask value
+ *
+ * @param priMask PriMask
+ *
+ * Set the priority mask bit in the priority mask register
+ */
+extern void __set_PRIMASK(uint32_t priMask);
+
+/**
+ * @brief Return the Fault Mask value
+ *
+ * @return FaultMask
+ *
+ * Return the content of the fault mask register
+ */
+extern uint32_t __get_FAULTMASK(void);
+
+/**
+ * @brief Set the Fault Mask value
+ *
+ * @param faultMask faultMask value
+ *
+ * Set the fault mask register
+ */
+extern void __set_FAULTMASK(uint32_t faultMask);
+
+/**
+ * @brief Return the Control Register value
+ *
+ * @return Control value
+ *
+ * Return the content of the control register
+ */
+extern uint32_t __get_CONTROL(void);
+
+/**
+ * @brief Set the Control Register value
+ *
+ * @param control Control value
+ *
+ * Set the control register
+ */
+extern void __set_CONTROL(uint32_t control);
+
+#else /* (__ARMCC_VERSION >= 400000) */
+
+/**
+ * @brief Remove the exclusive lock created by ldrex
+ *
+ * Removes the exclusive lock which is created by ldrex.
+ */
+#define __CLREX __clrex
+
+/**
+ * @brief Return the Base Priority value
+ *
+ * @return BasePriority
+ *
+ * Return the content of the base priority register
+ */
+static __INLINE uint32_t __get_BASEPRI(void)
+{
+ register uint32_t __regBasePri __ASM("basepri");
+ return(__regBasePri);
+}
+
+/**
+ * @brief Set the Base Priority value
+ *
+ * @param basePri BasePriority
+ *
+ * Set the base priority register
+ */
+static __INLINE void __set_BASEPRI(uint32_t basePri)
+{
+ register uint32_t __regBasePri __ASM("basepri");
+ __regBasePri = (basePri & 0xff);
+}
+
+/**
+ * @brief Return the Priority Mask value
+ *
+ * @return PriMask
+ *
+ * Return state of the priority mask bit from the priority mask register
+ */
+static __INLINE uint32_t __get_PRIMASK(void)
+{
+ register uint32_t __regPriMask __ASM("primask");
+ return(__regPriMask);
+}
+
+/**
+ * @brief Set the Priority Mask value
+ *
+ * @param priMask PriMask
+ *
+ * Set the priority mask bit in the priority mask register
+ */
+static __INLINE void __set_PRIMASK(uint32_t priMask)
+{
+ register uint32_t __regPriMask __ASM("primask");
+ __regPriMask = (priMask);
+}
+
+/**
+ * @brief Return the Fault Mask value
+ *
+ * @return FaultMask
+ *
+ * Return the content of the fault mask register
+ */
+static __INLINE uint32_t __get_FAULTMASK(void)
+{
+ register uint32_t __regFaultMask __ASM("faultmask");
+ return(__regFaultMask);
+}
+
+/**
+ * @brief Set the Fault Mask value
+ *
+ * @param faultMask faultMask value
+ *
+ * Set the fault mask register
+ */
+static __INLINE void __set_FAULTMASK(uint32_t faultMask)
+{
+ register uint32_t __regFaultMask __ASM("faultmask");
+ __regFaultMask = (faultMask & 1);
+}
+
+/**
+ * @brief Return the Control Register value
+ *
+ * @return Control value
+ *
+ * Return the content of the control register
+ */
+static __INLINE uint32_t __get_CONTROL(void)
+{
+ register uint32_t __regControl __ASM("control");
+ return(__regControl);
+}
+
+/**
+ * @brief Set the Control Register value
+ *
+ * @param control Control value
+ *
+ * Set the control register
+ */
+static __INLINE void __set_CONTROL(uint32_t control)
+{
+ register uint32_t __regControl __ASM("control");
+ __regControl = control;
+}
+
+#endif /* __ARMCC_VERSION */
+
+
+
+#elif (defined (__ICCARM__)) /*------------------ ICC Compiler -------------------*/
+/* IAR iccarm specific functions */
+
+#define __enable_irq __enable_interrupt /*!< global Interrupt enable */
+#define __disable_irq __disable_interrupt /*!< global Interrupt disable */
+
+static __INLINE void __enable_fault_irq() { __ASM ("cpsie f"); }
+static __INLINE void __disable_fault_irq() { __ASM ("cpsid f"); }
+
+#define __NOP __no_operation /*!< no operation intrinsic in IAR Compiler */
+static __INLINE void __WFI() { __ASM ("wfi"); }
+static __INLINE void __WFE() { __ASM ("wfe"); }
+static __INLINE void __SEV() { __ASM ("sev"); }
+static __INLINE void __CLREX() { __ASM ("clrex"); }
+
+/* intrinsic void __ISB(void) */
+/* intrinsic void __DSB(void) */
+/* intrinsic void __DMB(void) */
+/* intrinsic void __set_PRIMASK(); */
+/* intrinsic void __get_PRIMASK(); */
+/* intrinsic void __set_FAULTMASK(); */
+/* intrinsic void __get_FAULTMASK(); */
+/* intrinsic uint32_t __REV(uint32_t value); */
+/* intrinsic uint32_t __REVSH(uint32_t value); */
+/* intrinsic unsigned long __STREX(unsigned long, unsigned long); */
+/* intrinsic unsigned long __LDREX(unsigned long *); */
+
+
+/**
+ * @brief Return the Process Stack Pointer
+ *
+ * @return ProcessStackPointer
+ *
+ * Return the actual process stack pointer
+ */
+extern uint32_t __get_PSP(void);
+
+/**
+ * @brief Set the Process Stack Pointer
+ *
+ * @param topOfProcStack Process Stack Pointer
+ *
+ * Assign the value ProcessStackPointer to the MSP
+ * (process stack pointer) Cortex processor register
+ */
+extern void __set_PSP(uint32_t topOfProcStack);
+
+/**
+ * @brief Return the Main Stack Pointer
+ *
+ * @return Main Stack Pointer
+ *
+ * Return the current value of the MSP (main stack pointer)
+ * Cortex processor register
+ */
+extern uint32_t __get_MSP(void);
+
+/**
+ * @brief Set the Main Stack Pointer
+ *
+ * @param topOfMainStack Main Stack Pointer
+ *
+ * Assign the value mainStackPointer to the MSP
+ * (main stack pointer) Cortex processor register
+ */
+extern void __set_MSP(uint32_t topOfMainStack);
+
+/**
+ * @brief Reverse byte order in unsigned short value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in unsigned short value
+ */
+extern uint32_t __REV16(uint16_t value);
+
+/**
+ * @brief Reverse bit order of value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse bit order of value
+ */
+extern uint32_t __RBIT(uint32_t value);
+
+/**
+ * @brief LDR Exclusive (8 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 8 bit values)
+ */
+extern uint8_t __LDREXB(uint8_t *addr);
+
+/**
+ * @brief LDR Exclusive (16 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 16 bit values
+ */
+extern uint16_t __LDREXH(uint16_t *addr);
+
+/**
+ * @brief LDR Exclusive (32 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 32 bit values
+ */
+extern uint32_t __LDREXW(uint32_t *addr);
+
+/**
+ * @brief STR Exclusive (8 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 8 bit values
+ */
+extern uint32_t __STREXB(uint8_t value, uint8_t *addr);
+
+/**
+ * @brief STR Exclusive (16 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 16 bit values
+ */
+extern uint32_t __STREXH(uint16_t value, uint16_t *addr);
+
+/**
+ * @brief STR Exclusive (32 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 32 bit values
+ */
+extern uint32_t __STREXW(uint32_t value, uint32_t *addr);
+
+
+
+#elif (defined (__GNUC__)) /*------------------ GNU Compiler ---------------------*/
+/* GNU gcc specific functions */
+
+static __INLINE void __enable_irq() { __ASM volatile ("cpsie i"); }
+static __INLINE void __disable_irq() { __ASM volatile ("cpsid i"); }
+
+static __INLINE void __enable_fault_irq() { __ASM volatile ("cpsie f"); }
+static __INLINE void __disable_fault_irq() { __ASM volatile ("cpsid f"); }
+
+static __INLINE void __NOP() { __ASM volatile ("nop"); }
+static __INLINE void __WFI() { __ASM volatile ("wfi"); }
+static __INLINE void __WFE() { __ASM volatile ("wfe"); }
+static __INLINE void __SEV() { __ASM volatile ("sev"); }
+static __INLINE void __ISB() { __ASM volatile ("isb"); }
+static __INLINE void __DSB() { __ASM volatile ("dsb"); }
+static __INLINE void __DMB() { __ASM volatile ("dmb"); }
+static __INLINE void __CLREX() { __ASM volatile ("clrex"); }
+
+
+/**
+ * @brief Return the Process Stack Pointer
+ *
+ * @return ProcessStackPointer
+ *
+ * Return the actual process stack pointer
+ */
+extern uint32_t __get_PSP(void);
+
+/**
+ * @brief Set the Process Stack Pointer
+ *
+ * @param topOfProcStack Process Stack Pointer
+ *
+ * Assign the value ProcessStackPointer to the MSP
+ * (process stack pointer) Cortex processor register
+ */
+extern void __set_PSP(uint32_t topOfProcStack);
+
+/**
+ * @brief Return the Main Stack Pointer
+ *
+ * @return Main Stack Pointer
+ *
+ * Return the current value of the MSP (main stack pointer)
+ * Cortex processor register
+ */
+extern uint32_t __get_MSP(void);
+
+/**
+ * @brief Set the Main Stack Pointer
+ *
+ * @param topOfMainStack Main Stack Pointer
+ *
+ * Assign the value mainStackPointer to the MSP
+ * (main stack pointer) Cortex processor register
+ */
+extern void __set_MSP(uint32_t topOfMainStack);
+
+/**
+ * @brief Return the Base Priority value
+ *
+ * @return BasePriority
+ *
+ * Return the content of the base priority register
+ */
+extern uint32_t __get_BASEPRI(void);
+
+/**
+ * @brief Set the Base Priority value
+ *
+ * @param basePri BasePriority
+ *
+ * Set the base priority register
+ */
+extern void __set_BASEPRI(uint32_t basePri);
+
+/**
+ * @brief Return the Priority Mask value
+ *
+ * @return PriMask
+ *
+ * Return state of the priority mask bit from the priority mask register
+ */
+extern uint32_t __get_PRIMASK(void);
+
+/**
+ * @brief Set the Priority Mask value
+ *
+ * @param priMask PriMask
+ *
+ * Set the priority mask bit in the priority mask register
+ */
+extern void __set_PRIMASK(uint32_t priMask);
+
+/**
+ * @brief Return the Fault Mask value
+ *
+ * @return FaultMask
+ *
+ * Return the content of the fault mask register
+ */
+extern uint32_t __get_FAULTMASK(void);
+
+/**
+ * @brief Set the Fault Mask value
+ *
+ * @param faultMask faultMask value
+ *
+ * Set the fault mask register
+ */
+extern void __set_FAULTMASK(uint32_t faultMask);
+
+/**
+ * @brief Return the Control Register value
+*
+* @return Control value
+ *
+ * Return the content of the control register
+ */
+extern uint32_t __get_CONTROL(void);
+
+/**
+ * @brief Set the Control Register value
+ *
+ * @param control Control value
+ *
+ * Set the control register
+ */
+extern void __set_CONTROL(uint32_t control);
+
+/**
+ * @brief Reverse byte order in integer value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in integer value
+ */
+extern uint32_t __REV(uint32_t value);
+
+/**
+ * @brief Reverse byte order in unsigned short value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in unsigned short value
+ */
+extern uint32_t __REV16(uint16_t value);
+
+/**
+ * @brief Reverse byte order in signed short value with sign extension to integer
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse byte order in signed short value with sign extension to integer
+ */
+extern int32_t __REVSH(int16_t value);
+
+/**
+ * @brief Reverse bit order of value
+ *
+ * @param value value to reverse
+ * @return reversed value
+ *
+ * Reverse bit order of value
+ */
+extern uint32_t __RBIT(uint32_t value);
+
+/**
+ * @brief LDR Exclusive (8 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 8 bit value
+ */
+extern uint8_t __LDREXB(uint8_t *addr);
+
+/**
+ * @brief LDR Exclusive (16 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 16 bit values
+ */
+extern uint16_t __LDREXH(uint16_t *addr);
+
+/**
+ * @brief LDR Exclusive (32 bit)
+ *
+ * @param *addr address pointer
+ * @return value of (*address)
+ *
+ * Exclusive LDR command for 32 bit values
+ */
+extern uint32_t __LDREXW(uint32_t *addr);
+
+/**
+ * @brief STR Exclusive (8 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 8 bit values
+ */
+extern uint32_t __STREXB(uint8_t value, uint8_t *addr);
+
+/**
+ * @brief STR Exclusive (16 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 16 bit values
+ */
+extern uint32_t __STREXH(uint16_t value, uint16_t *addr);
+
+/**
+ * @brief STR Exclusive (32 bit)
+ *
+ * @param value value to store
+ * @param *addr address pointer
+ * @return successful / failed
+ *
+ * Exclusive STR command for 32 bit values
+ */
+extern uint32_t __STREXW(uint32_t value, uint32_t *addr);
+
+
+#elif (defined (__TASKING__)) /*------------------ TASKING Compiler ---------------------*/
+/* TASKING carm specific functions */
+
+/*
+ * The CMSIS functions have been implemented as intrinsics in the compiler.
+ * Please use "carm -?i" to get an up to date list of all instrinsics,
+ * Including the CMSIS ones.
+ */
+
+#endif
+
+
+/** @addtogroup CMSIS_CM3_Core_FunctionInterface CMSIS CM3 Core Function Interface
+ Core Function Interface containing:
+ - Core NVIC Functions
+ - Core SysTick Functions
+ - Core Reset Functions
+*/
+/*@{*/
+
+/* ########################## NVIC functions #################################### */
+
+/**
+ * @brief Set the Priority Grouping in NVIC Interrupt Controller
+ *
+ * @param PriorityGroup is priority grouping field
+ *
+ * Set the priority grouping field using the required unlock sequence.
+ * The parameter priority_grouping is assigned to the field
+ * SCB->AIRCR [10:8] PRIGROUP field. Only values from 0..7 are used.
+ * In case of a conflict between priority grouping and available
+ * priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+ */
+static __INLINE void NVIC_SetPriorityGrouping(uint32_t PriorityGroup)
+{
+ uint32_t reg_value;
+ uint32_t PriorityGroupTmp = (PriorityGroup & 0x07); /* only values 0..7 are used */
+
+ reg_value = SCB->AIRCR; /* read old register configuration */
+ reg_value &= ~(SCB_AIRCR_VECTKEY_Msk | SCB_AIRCR_PRIGROUP_Msk); /* clear bits to change */
+ reg_value = (reg_value |
+ (0x5FA << SCB_AIRCR_VECTKEY_Pos) |
+ (PriorityGroupTmp << 8)); /* Insert write key and priorty group */
+ SCB->AIRCR = reg_value;
+}
+
+/**
+ * @brief Get the Priority Grouping from NVIC Interrupt Controller
+ *
+ * @return priority grouping field
+ *
+ * Get the priority grouping from NVIC Interrupt Controller.
+ * priority grouping is SCB->AIRCR [10:8] PRIGROUP field.
+ */
+static __INLINE uint32_t NVIC_GetPriorityGrouping(void)
+{
+ return ((SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) >> SCB_AIRCR_PRIGROUP_Pos); /* read priority grouping field */
+}
+
+/**
+ * @brief Enable Interrupt in NVIC Interrupt Controller
+ *
+ * @param IRQn The positive number of the external interrupt to enable
+ *
+ * Enable a device specific interupt in the NVIC interrupt controller.
+ * The interrupt number cannot be a negative value.
+ */
+static __INLINE void NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+ NVIC->ISER[((uint32_t)(IRQn) >> 5)] = (1 << ((uint32_t)(IRQn) & 0x1F)); /* enable interrupt */
+}
+
+/**
+ * @brief Disable the interrupt line for external interrupt specified
+ *
+ * @param IRQn The positive number of the external interrupt to disable
+ *
+ * Disable a device specific interupt in the NVIC interrupt controller.
+ * The interrupt number cannot be a negative value.
+ */
+static __INLINE void NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+ NVIC->ICER[((uint32_t)(IRQn) >> 5)] = (1 << ((uint32_t)(IRQn) & 0x1F)); /* disable interrupt */
+}
+
+/**
+ * @brief Read the interrupt pending bit for a device specific interrupt source
+ *
+ * @param IRQn The number of the device specifc interrupt
+ * @return 1 = interrupt pending, 0 = interrupt not pending
+ *
+ * Read the pending register in NVIC and return 1 if its status is pending,
+ * otherwise it returns 0
+ */
+static __INLINE uint32_t NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+ return((uint32_t) ((NVIC->ISPR[(uint32_t)(IRQn) >> 5] & (1 << ((uint32_t)(IRQn) & 0x1F)))?1:0)); /* Return 1 if pending else 0 */
+}
+
+/**
+ * @brief Set the pending bit for an external interrupt
+ *
+ * @param IRQn The number of the interrupt for set pending
+ *
+ * Set the pending bit for the specified interrupt.
+ * The interrupt number cannot be a negative value.
+ */
+static __INLINE void NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+ NVIC->ISPR[((uint32_t)(IRQn) >> 5)] = (1 << ((uint32_t)(IRQn) & 0x1F)); /* set interrupt pending */
+}
+
+/**
+ * @brief Clear the pending bit for an external interrupt
+ *
+ * @param IRQn The number of the interrupt for clear pending
+ *
+ * Clear the pending bit for the specified interrupt.
+ * The interrupt number cannot be a negative value.
+ */
+static __INLINE void NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+ NVIC->ICPR[((uint32_t)(IRQn) >> 5)] = (1 << ((uint32_t)(IRQn) & 0x1F)); /* Clear pending interrupt */
+}
+
+/**
+ * @brief Read the active bit for an external interrupt
+ *
+ * @param IRQn The number of the interrupt for read active bit
+ * @return 1 = interrupt active, 0 = interrupt not active
+ *
+ * Read the active register in NVIC and returns 1 if its status is active,
+ * otherwise it returns 0.
+ */
+static __INLINE uint32_t NVIC_GetActive(IRQn_Type IRQn)
+{
+ return((uint32_t)((NVIC->IABR[(uint32_t)(IRQn) >> 5] & (1 << ((uint32_t)(IRQn) & 0x1F)))?1:0)); /* Return 1 if active else 0 */
+}
+
+/**
+ * @brief Set the priority for an interrupt
+ *
+ * @param IRQn The number of the interrupt for set priority
+ * @param priority The priority to set
+ *
+ * Set the priority for the specified interrupt. The interrupt
+ * number can be positive to specify an external (device specific)
+ * interrupt, or negative to specify an internal (core) interrupt.
+ *
+ * Note: The priority cannot be set for every core interrupt.
+ */
+static __INLINE void NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+ if(IRQn < 0) {
+ SCB->SHP[((uint32_t)(IRQn) & 0xF)-4] = ((priority << (8 - __NVIC_PRIO_BITS)) & 0xff); } /* set Priority for Cortex-M3 System Interrupts */
+ else {
+ NVIC->IP[(uint32_t)(IRQn)] = ((priority << (8 - __NVIC_PRIO_BITS)) & 0xff); } /* set Priority for device specific Interrupts */
+}
+
+/**
+ * @brief Read the priority for an interrupt
+ *
+ * @param IRQn The number of the interrupt for get priority
+ * @return The priority for the interrupt
+ *
+ * Read the priority for the specified interrupt. The interrupt
+ * number can be positive to specify an external (device specific)
+ * interrupt, or negative to specify an internal (core) interrupt.
+ *
+ * The returned priority value is automatically aligned to the implemented
+ * priority bits of the microcontroller.
+ *
+ * Note: The priority cannot be set for every core interrupt.
+ */
+static __INLINE uint32_t NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+ if(IRQn < 0) {
+ return((uint32_t)(SCB->SHP[((uint32_t)(IRQn) & 0xF)-4] >> (8 - __NVIC_PRIO_BITS))); } /* get priority for Cortex-M3 system interrupts */
+ else {
+ return((uint32_t)(NVIC->IP[(uint32_t)(IRQn)] >> (8 - __NVIC_PRIO_BITS))); } /* get priority for device specific interrupts */
+}
+
+
+/**
+ * @brief Encode the priority for an interrupt
+ *
+ * @param PriorityGroup The used priority group
+ * @param PreemptPriority The preemptive priority value (starting from 0)
+ * @param SubPriority The sub priority value (starting from 0)
+ * @return The encoded priority for the interrupt
+ *
+ * Encode the priority for an interrupt with the given priority group,
+ * preemptive priority value and sub priority value.
+ * In case of a conflict between priority grouping and available
+ * priority bits (__NVIC_PRIO_BITS) the samllest possible priority group is set.
+ *
+ * The returned priority value can be used for NVIC_SetPriority(...) function
+ */
+static __INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+ uint32_t PriorityGroupTmp = (PriorityGroup & 0x07); /* only values 0..7 are used */
+ uint32_t PreemptPriorityBits;
+ uint32_t SubPriorityBits;
+
+ PreemptPriorityBits = ((7 - PriorityGroupTmp) > __NVIC_PRIO_BITS) ? __NVIC_PRIO_BITS : 7 - PriorityGroupTmp;
+ SubPriorityBits = ((PriorityGroupTmp + __NVIC_PRIO_BITS) < 7) ? 0 : PriorityGroupTmp - 7 + __NVIC_PRIO_BITS;
+
+ return (
+ ((PreemptPriority & ((1 << (PreemptPriorityBits)) - 1)) << SubPriorityBits) |
+ ((SubPriority & ((1 << (SubPriorityBits )) - 1)))
+ );
+}
+
+
+/**
+ * @brief Decode the priority of an interrupt
+ *
+ * @param Priority The priority for the interrupt
+ * @param PriorityGroup The used priority group
+ * @param pPreemptPriority The preemptive priority value (starting from 0)
+ * @param pSubPriority The sub priority value (starting from 0)
+ *
+ * Decode an interrupt priority value with the given priority group to
+ * preemptive priority value and sub priority value.
+ * In case of a conflict between priority grouping and available
+ * priority bits (__NVIC_PRIO_BITS) the samllest possible priority group is set.
+ *
+ * The priority value can be retrieved with NVIC_GetPriority(...) function
+ */
+static __INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* pPreemptPriority, uint32_t* pSubPriority)
+{
+ uint32_t PriorityGroupTmp = (PriorityGroup & 0x07); /* only values 0..7 are used */
+ uint32_t PreemptPriorityBits;
+ uint32_t SubPriorityBits;
+
+ PreemptPriorityBits = ((7 - PriorityGroupTmp) > __NVIC_PRIO_BITS) ? __NVIC_PRIO_BITS : 7 - PriorityGroupTmp;
+ SubPriorityBits = ((PriorityGroupTmp + __NVIC_PRIO_BITS) < 7) ? 0 : PriorityGroupTmp - 7 + __NVIC_PRIO_BITS;
+
+ *pPreemptPriority = (Priority >> SubPriorityBits) & ((1 << (PreemptPriorityBits)) - 1);
+ *pSubPriority = (Priority ) & ((1 << (SubPriorityBits )) - 1);
+}
+
+
+
+/* ################################## SysTick function ############################################ */
+
+#if (!defined (__Vendor_SysTickConfig)) || (__Vendor_SysTickConfig == 0)
+
+/**
+ * @brief Initialize and start the SysTick counter and its interrupt.
+ *
+ * @param ticks number of ticks between two interrupts
+ * @return 1 = failed, 0 = successful
+ *
+ * Initialise the system tick timer and its interrupt and start the
+ * system tick timer / counter in free running mode to generate
+ * periodical interrupts.
+ */
+static __INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+ if (ticks > SysTick_LOAD_RELOAD_Msk) return (1); /* Reload value impossible */
+
+ SysTick->LOAD = (ticks & SysTick_LOAD_RELOAD_Msk) - 1; /* set reload register */
+ NVIC_SetPriority (SysTick_IRQn, (1<<__NVIC_PRIO_BITS) - 1); /* set Priority for Cortex-M0 System Interrupts */
+ SysTick->VAL = 0; /* Load the SysTick Counter Value */
+ SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk |
+ SysTick_CTRL_TICKINT_Msk |
+ SysTick_CTRL_ENABLE_Msk; /* Enable SysTick IRQ and SysTick Timer */
+ return (0); /* Function successful */
+}
+
+#endif
+
+
+
+
+/* ################################## Reset function ############################################ */
+
+/**
+ * @brief Initiate a system reset request.
+ *
+ * Initiate a system reset request to reset the MCU
+ */
+static __INLINE void NVIC_SystemReset(void)
+{
+ SCB->AIRCR = ((0x5FA << SCB_AIRCR_VECTKEY_Pos) |
+ (SCB->AIRCR & SCB_AIRCR_PRIGROUP_Msk) |
+ SCB_AIRCR_SYSRESETREQ_Msk); /* Keep priority group unchanged */
+ __DSB(); /* Ensure completion of memory access */
+ while(1); /* wait until reset */
+}
+
+/*@}*/ /* end of group CMSIS_CM3_Core_FunctionInterface */
+
+
+
+/* ##################################### Debug In/Output function ########################################### */
+
+/** @addtogroup CMSIS_CM3_CoreDebugInterface CMSIS CM3 Core Debug Interface
+ Core Debug Interface containing:
+ - Core Debug Receive / Transmit Functions
+ - Core Debug Defines
+ - Core Debug Variables
+*/
+/*@{*/
+
+extern volatile int ITM_RxBuffer; /*!< variable to receive characters */
+#define ITM_RXBUFFER_EMPTY 0x5AA55AA5 /*!< value identifying ITM_RxBuffer is ready for next character */
+
+
+/**
+ * @brief Outputs a character via the ITM channel 0
+ *
+ * @param ch character to output
+ * @return character to output
+ *
+ * The function outputs a character via the ITM channel 0.
+ * The function returns when no debugger is connected that has booked the output.
+ * It is blocking when a debugger is connected, but the previous character send is not transmitted.
+ */
+static __INLINE uint32_t ITM_SendChar (uint32_t ch)
+{
+ if ((CoreDebug->DEMCR & CoreDebug_DEMCR_TRCENA_Msk) && /* Trace enabled */
+ (ITM->TCR & ITM_TCR_ITMENA_Msk) && /* ITM enabled */
+ (ITM->TER & (1ul << 0) ) ) /* ITM Port #0 enabled */
+ {
+ while (ITM->PORT[0].u32 == 0);
+ ITM->PORT[0].u8 = (uint8_t) ch;
+ }
+ return (ch);
+}
+
+
+/**
+ * @brief Inputs a character via variable ITM_RxBuffer
+ *
+ * @return received character, -1 = no character received
+ *
+ * The function inputs a character via variable ITM_RxBuffer.
+ * The function returns when no debugger is connected that has booked the output.
+ * It is blocking when a debugger is connected, but the previous character send is not transmitted.
+ */
+static __INLINE int ITM_ReceiveChar (void) {
+ int ch = -1; /* no character available */
+
+ if (ITM_RxBuffer != ITM_RXBUFFER_EMPTY) {
+ ch = ITM_RxBuffer;
+ ITM_RxBuffer = ITM_RXBUFFER_EMPTY; /* ready for next character */
+ }
+
+ return (ch);
+}
+
+
+/**
+ * @brief Check if a character via variable ITM_RxBuffer is available
+ *
+ * @return 1 = character available, 0 = no character available
+ *
+ * The function checks variable ITM_RxBuffer whether a character is available or not.
+ * The function returns '1' if a character is available and '0' if no character is available.
+ */
+static __INLINE int ITM_CheckChar (void) {
+
+ if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) {
+ return (0); /* no character available */
+ } else {
+ return (1); /* character available */
+ }
+}
+
+/*@}*/ /* end of group CMSIS_CM3_core_DebugInterface */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+/*@}*/ /* end of group CMSIS_CM3_core_definitions */
+
+#endif /* __CM3_CORE_H__ */
+
+/*lint -restore */
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/Release_Notes.html b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/Release_Notes.html
new file mode 100644
index 00000000..b80f38df
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/Release_Notes.html
@@ -0,0 +1,284 @@
+
+
+
+
+
+
+
+
+
+
+
+
+Release Notes for STM32F10x CMSIS
+
+
+
+
+
+
+
+ All
+STM32 devices definitions are commented by default. User has to select the
+appropriate device before starting else an error will be signaled on compile
+time.
+
Add new IRQs definitons inside the IRQn_Type enumeration for STM23 High-density Value line devices.
+
"bool" type removed.
+
+
STM32F10x CMSIS Cortex-M3 Device Peripheral Access Layer System Files:system_stm32f10x.h and system_stm32f10x.c
+
+
+
"system_stm32f10x.c" moved to to "STM32F10x_StdPeriph_Template" directory. This file is also moved to each example directory under "STM32F10x_StdPeriph_Examples".
+
+
SystemInit_ExtMemCtl() function: update to support High-density Value line devices.
+
Add "VECT_TAB_SRAM" inside "system_stm32f10x.c"
+to select if the user want to place the Vector Table in internal SRAM.
+An additional define is also to specify the Vector Table offset "VECT_TAB_OFFSET".
+
Update
+the stm32f10x.h file to support new Value line devices features: CEC
+peripheral, new General purpose timers TIM15, TIM16 and TIM17.
+
Peripherals Bits definitions updated to be in line with Value line devices available features.
+
+
HSE_Value,
+HSI_Value and HSEStartup_TimeOut changed to upper case: HSE_VALUE,
+HSI_VALUE and HSE_STARTUP_TIMEOUT. Old names are kept for legacy
+purposes.
+
+
+
STM32F10x CMSIS Cortex-M3 Device Peripheral Access Layer System Files:system_stm32f10x.h and system_stm32f10x.c
+
+
+
SystemFrequency variable name changed to SystemCoreClock
+
+
Default
+ SystemCoreClock is changed to 24MHz when Value line devices are selected and to 72MHz on other devices.
+
+
All while(1) loop were removed from all clock setting functions. User has to handle the HSE startup failure.
+
+
Additional function void SystemCoreClockUpdate (void) is provided.
+
Add new
+startup files for STM32 Low-density Value line devices:
+ startup_stm32f10x_ld_vl.s
+
Add new startup
+files for STM32 Medium-density Value line devices:
+ startup_stm32f10x_md_vl.s
+
SystemInit() function is called from startup file (startup_stm32f10x_xx.s) before to branch to application main.
+To reconfigure the default setting of SystemInit() function, refer to system_stm32f10x.c file
+
+
GNU startup file for Low density devices (startup_stm32f10x_ld.s) is updated to fix compilation errors.
+
+
+
+
+
+
+
+
License
+
The
+enclosed firmware and all the related documentation are not covered by
+a License Agreement, if you need such License you can contact your
+local STMicroelectronics office.
+
THE
+PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO
+SAVE TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR
+ANY DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY
+CLAIMS ARISING FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY
+CUSTOMERS OF THE CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH
+THEIR PRODUCTS.
+
+
+
+
For
+complete documentation on STM32(CORTEX M3) 32-Bit Microcontrollers
+visit www.st.com/STM32
+
+
+
+
+
+
+
+
+
+
+
+
+
\ No newline at end of file
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/stm32f10x.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/stm32f10x.h
new file mode 100644
index 00000000..af0c7c9a
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/stm32f10x.h
@@ -0,0 +1,8336 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x.h
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief CMSIS Cortex-M3 Device Peripheral Access Layer Header File.
+ * This file contains all the peripheral register's definitions, bits
+ * definitions and memory mapping for STM32F10x Connectivity line,
+ * High density, High density value line, Medium density,
+ * Medium density Value line, Low density, Low density Value line
+ * and XL-density devices.
+ *
+ * The file is the unique include file that the application programmer
+ * is using in the C source code, usually in main.c. This file contains:
+ * - Configuration section that allows to select:
+ * - The device used in the target application
+ * - To use or not the peripheral’s drivers in application code(i.e.
+ * code will be based on direct access to peripheral’s registers
+ * rather than drivers API), this option is controlled by
+ * "#define USE_STDPERIPH_DRIVER"
+ * - To change few application-specific parameters such as the HSE
+ * crystal frequency
+ * - Data structures and the address mapping for all peripherals
+ * - Peripheral's registers declarations and bits definition
+ * - Macros to access peripheral’s registers hardware
+ *
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ The Cortex-M3 incorporates the Instrumented Trace Macrocell (ITM) that provides together with
+ the Serial Viewer Output trace capabilities for the microcontroller system. The ITM has
+ 32 communication channels which are able to transmit 32 / 16 / 8 bit values; two ITM
+ communication channels are used by CMSIS to output the following information:
+
+
+
ITM Channel 0: used for printf-style output via the debug interface.
+
ITM Channel 31: is reserved for RTOS kernel awareness debugging.
+
+
+
Debug IN / OUT functions
+
CMSIS provides following debug functions:
+
+
ITM_SendChar (uses ITM channel 0)
+
ITM_ReceiveChar (uses global variable)
+
ITM_CheckChar (uses global variable)
+
+
+
ITM_SendChar
+
+ ITM_SendChar is used to transmit a character over ITM channel 0 from
+ the microcontroller system to the debug system.
+ Only a 8 bit value is transmitted.
+
+ ITM communication channel is only capable for OUT direction. For IN direction
+ a globel variable is used. A simple mechansim detects if a character is received.
+ The project to test need to be build with debug information.
+
+
+
+ The globale variable ITM_RxBuffer is used to transmit a 8 bit value from debug system
+ to microcontroller system. ITM_RxBuffer is 32 bit wide to enshure a proper handshake.
+
+
+extern volatile int ITM_RxBuffer; /* variable to receive characters */
+
+
+ A dedicated bit pattern is used to determin if ITM_RxBuffer is empty
+ or contains a valid value.
+
+
+#define ITM_RXBUFFER_EMPTY 0x5AA55AA5 /* value identifying ITM_RxBuffer is ready for next character */
+
+
+ ITM_ReceiveChar is used to receive a 8 bit value from the debug system. The function is nonblocking.
+ It returns the received character or '-1' if no character was available.
+
+
+static __INLINE int ITM_ReceiveChar (void) {
+ int ch = -1; /* no character available */
+
+ if (ITM_RxBuffer != ITM_RXBUFFER_EMPTY) {
+ ch = ITM_RxBuffer;
+ ITM_RxBuffer = ITM_RXBUFFER_EMPTY; /* ready for next character */
+ }
+
+ return (ch);
+}
+
+
+
ITM_CheckChar
+
+ ITM_CheckChar is used to check if a character is received.
+
+
+static __INLINE int ITM_CheckChar (void) {
+
+ if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) {
+ return (0); /* no character available */
+ } else {
+ return (1); /* character available */
+ }
+}
+
+
+
ITM Debug Support in uVision
+
+ uVision uses in a debug session the Debug (printf) Viewer window to
+ display the debug data.
+
+
Direction microcontroller system -> uVision:
+
+
+ Characters received via ITM communication channel 0 are written in a printf style
+ to Debug (printf) Viewer window.
+
+
+
+
Direction uVision -> microcontroller system:
+
+
Check if ITM_RxBuffer variable is available (only performed once).
+
Read character from Debug (printf) Viewer window.
+
If ITM_RxBuffer empty write character to ITM_RxBuffer.
+
+
+
Note
+
+
Current solution does not use a buffer machanism for trasmitting the characters.
+
+
+
+
RTX Kernel awareness in uVision
+
+ uVision / RTX are using a simple and efficient solution for RTX Kernel awareness.
+ No format overhead is necessary.
+ uVsion debugger decodes the RTX events via the 32 / 16 / 8 bit ITM write access
+ to ITM communication channel 31.
+
+
+
Following RTX events are traced:
+
+
Task Create / Delete event
+
+
32 bit access. Task start address is transmitted
+
16 bit access. Task ID and Create/Delete flag are transmitted
+ High byte holds Create/Delete flag, Low byte holds TASK ID.
+
+
+
+
Task switch event
+
+
8 bit access. Task ID of current task is transmitted
+
+
+
+
+
Note
+
+
Other RTOS information could be retrieved via memory read access in a polling mode manner.
+
+
+
+
\ No newline at end of file
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CMSIS_changes.htm b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CMSIS_changes.htm
new file mode 100644
index 00000000..162ffcc9
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/CMSIS_changes.htm
@@ -0,0 +1,320 @@
+
+
+
+CMSIS Changes
+
+
+
+
+
+
+
+
+
Changes to CMSIS version V1.20
+
+
+
+
1. Removed CMSIS Middelware packages
+
+ CMSIS Middleware is on hold from ARM side until a agreement between all CMSIS partners is found.
+
+
+
2. SystemFrequency renamed to SystemCoreClock
+
+ The variable name SystemCoreClock is more precise than SystemFrequency
+ because the variable holds the clock value at which the core is running.
+
+
+
3. Changed startup concept
+
+ The old startup concept (calling SystemInit_ExtMemCtl from startup file and calling SystemInit
+ from main) has the weakness that it does not work for controllers which need a already
+ configuerd clock system to configure the external memory controller.
+
+
+
Changed startup concept
+
+
+ SystemInit() is called from startup file before premain.
+
+
+ SystemInit() configures the clock system and also configures
+ an existing external memory controller.
+
+
+ SystemInit() must not use global variables.
+
+
+ SystemCoreClock is initialized with a correct predefined value.
+
+
+ Additional function void SystemCoreClockUpdate (void) is provided.
+ SystemCoreClockUpdate() updates the variable SystemCoreClock
+ and must be called whenever the core clock is changed.
+ SystemCoreClockUpdate() evaluates the clock register settings and calculates
+ the current core clock.
+
+
+
+
+
4. Advanced Debug Functions
+
+ ITM communication channel is only capable for OUT direction. To allow also communication for
+ IN direction a simple concept is provided.
+
+
+
+ Global variable volatile int ITM_RxBuffer used for IN data.
+
+
+ Function int ITM_CheckChar (void) checks if a new character is available.
+
+
+ Function int ITM_ReceiveChar (void) retrieves the new character.
+
+
+
+
+ For detailed explanation see file CMSIS debug support.htm.
+
+
+
+
5. Core Register Bit Definitions
+
+ Files core_cm3.h and core_cm0.h contain now bit definitions for Core Registers. The name for the
+ defines correspond with the Cortex-M Technical Reference Manual.
+
+ The Cortex Microcontroller Software Interface Standard (CMSIS) answers the challenges
+ that are faced when software components are deployed to physical microcontroller devices based on a
+ Cortex-M0 or Cortex-M3 processor. The CMSIS will be also expanded to future Cortex-M
+ processor cores (the term Cortex-M is used to indicate that). The CMSIS is defined in close co-operation
+ with various silicon and software vendors and provides a common approach to interface to peripherals,
+ real-time operating systems, and middleware components.
+
+
+
ARM provides as part of the CMSIS the following software layers that are
+available for various compiler implementations:
+
+
Core Peripheral Access Layer: contains name definitions,
+ address definitions and helper functions to
+ access core registers and peripherals. It defines also a device
+ independent interface for RTOS Kernels that includes debug channel
+ definitions.
+
+
+
These software layers are expanded by Silicon partners with:
+
+
Device Peripheral Access Layer: provides definitions
+ for all device peripherals
+
Access Functions for Peripherals (optional): provides
+ additional helper functions for peripherals
+
+
+
CMSIS defines for a Cortex-M Microcontroller System:
+
+
A common way to access peripheral registers
+ and a common way to define exception vectors.
+
The register names of the Core
+ Peripherals andthe names of the Core
+ Exception Vectors.
+
An device independent interface for RTOS Kernels including a debug
+ channel.
+
+
+
+ By using CMSIS compliant software components, the user can easier re-use template code.
+ CMSIS is intended to enable the combination of software components from multiple middleware vendors.
+
+
+
Coding Rules and Conventions
+
+
+ The following section describes the coding rules and conventions used in the CMSIS
+ implementation. It contains also information about data types and version number information.
+
+
+
Essentials
+
+
The CMSIS C code conforms to MISRA 2004 rules. In case of MISRA violations,
+ there are disable and enable sequences for PC-LINT inserted.
+
ANSI standard data types defined in the ANSI C header file
+ <stdint.h> are used.
+
#define constants that include expressions must be enclosed by
+ parenthesis.
+
Variables and parameters have a complete data type.
+
All functions in the Core Peripheral Access Layer are
+ re-entrant.
+
The Core Peripheral Access Layer has no blocking code
+ (which means that wait/query loops are done at other software layers).
+
For each exception/interrupt there is definition for:
+
+
an exception/interrupt handler with the postfix _Handler
+ (for exceptions) or _IRQHandler (for interrupts).
+
a default exception/interrupt handler (weak definition) that contains an endless loop.
+
a #define of the interrupt number with the postfix _IRQn.
+
+
+
+
Recommendations
+
+
The CMSIS recommends the following conventions for identifiers.
+
+
CAPITAL names to identify Core Registers, Peripheral Registers, and CPU Instructions.
+
CamelCase names to identify peripherals access functions and interrupts.
+
PERIPHERAL_ prefix to identify functions that belong to specify peripherals.
+
Doxygen comments for all functions are included as described under Function Comments below.
+
+
+Comments
+
+
+
Comments use the ANSI C90 style (/* comment */) or C++ style
+ (// comment). It is assumed that the programming tools support today
+ consistently the C++ comment style.
+
Function Comments provide for each function the following information:
+
+
one-line brief function overview.
+
detailed parameter explanation.
+
detailed information about return values.
+
detailed description of the actual function.
+
+
Doxygen Example:
+
+/**
+ * @brief Enable Interrupt in NVIC Interrupt Controller
+ * @param IRQn interrupt number that specifies the interrupt
+ * @return none.
+ * Enable the specified interrupt in the NVIC Interrupt Controller.
+ * Other settings of the interrupt such as priority are not affected.
+ */
+
+
+
+
Data Types and IO Type Qualifiers
+
+
+ The Cortex-M HAL uses the standard types from the standard ANSI C header file
+ <stdint.h>. IO Type Qualifiers are used to specify the access
+ to peripheral variables. IO Type Qualifiers are indented to be used for automatic generation of
+ debug information of peripheral registers.
+
+
+
+
+
+
IO Type Qualifier
+
#define
+
Description
+
+
+
__I
+
volatile const
+
Read access only
+
+
+
__O
+
volatile
+
Write access only
+
+
+
__IO
+
volatile
+
Read and write access
+
+
+
+
+
CMSIS Version Number
+
+ File core_cm3.h contains the version number of the CMSIS with the following define:
+
+
+
+#define __CM3_CMSIS_VERSION_MAIN (0x01) /* [31:16] main version */
+#define __CM3_CMSIS_VERSION_SUB (0x30) /* [15:0] sub version */
+#define __CM3_CMSIS_VERSION ((__CM3_CMSIS_VERSION_MAIN << 16) | __CM3_CMSIS_VERSION_SUB)
+
+
+ File core_cm0.h contains the version number of the CMSIS with the following define:
+
+
+
+#define __CM0_CMSIS_VERSION_MAIN (0x01) /* [31:16] main version */
+#define __CM0_CMSIS_VERSION_SUB (0x30) /* [15:0] sub version */
+#define __CM0_CMSIS_VERSION ((__CM0_CMSIS_VERSION_MAIN << 16) | __CM0_CMSIS_VERSION_SUB)
+
+
+
CMSIS Cortex Core
+
+ File core_cm3.h contains the type of the CMSIS Cortex-M with the following define:
+
+
+
+#define __CORTEX_M (0x03)
+
+
+ File core_cm0.h contains the type of the CMSIS Cortex-M with the following define:
+
+
+
+#define __CORTEX_M (0x00)
+
+
+
CMSIS Files
+
+ This section describes the Files provided in context with the CMSIS to access the Cortex-M
+ hardware and peripherals.
+
+
+
+
+
+
File
+
Provider
+
Description
+
+
+
device.h
+
Device specific (provided by silicon partner)
+
Defines the peripherals for the actual device. The file may use
+ several other include files to define the peripherals of the actual device.
+
+
+
core_cm0.h
+
ARM (for RealView ARMCC, IAR, and GNU GCC)
+
Defines the core peripherals for the Cortex-M0 CPU and core peripherals.
+
+
+
core_cm3.h
+
ARM (for RealView ARMCC, IAR, and GNU GCC)
+
Defines the core peripherals for the Cortex-M3 CPU and core peripherals.
+
+
+
core_cm0.c
+
ARM (for RealView ARMCC, IAR, and GNU GCC)
+
Provides helper functions that access core registers.
+
+
+
core_cm3.c
+
ARM (for RealView ARMCC, IAR, and GNU GCC)
+
Provides helper functions that access core registers.
+
+
+
startup_device
+
ARM (adapted by compiler partner / silicon partner)
+
Provides the Cortex-M startup code and the complete (device specific) Interrupt Vector Table
+
+
+
system_device
+
ARM (adapted by silicon partner)
+
Provides a device specific configuration file for the device. It configures the device initializes
+ typically the oscillator (PLL) that is part of the microcontroller device
+
+
+
+
+
device.h
+
+
+ The file device.h is provided by the silicon vendor and is the
+ central include file that the application programmer is using in
+ the C source code. This file contains:
+
+
+
+
Interrupt Number Definition: provides interrupt numbers
+ (IRQn) for all core and device specific exceptions and interrupts.
+
+
+
Configuration for core_cm0.h / core_cm3.h: reflects the
+ actual configuration of the Cortex-M processor that is part of the actual
+ device. As such the file core_cm0.h / core_cm3.h is included that
+ implements access to processor registers and core peripherals.
+
+
+
Device Peripheral Access Layer: provides definitions
+ for all device peripherals. It contains all data structures and the address
+ mapping for the device specific peripherals.
+
+
Access Functions for Peripherals (optional): provides
+ additional helper functions for peripherals that are useful for programming
+ of these peripherals. Access Functions may be provided as inline functions
+ or can be extern references to a device specific library provided by the
+ silicon vendor.
+
+
+
+
Interrupt Number Definition
+
+
To access the device specific interrupts the device.h file defines IRQn
+numbers for the complete device using a enum typedef as shown below:
+ The Cortex-M core configuration options which are defined for each device implementation. Some
+ configuration options are reflected in the CMSIS layer using the #define settings described below.
+
+
+ To access core peripherals file device.h includes file core_cm0.h / core_cm3.h.
+ Several features in core_cm0.h / core_cm3.h are configured by the following defines that must be
+ defined before #include <core_cm0.h> / #include <core_cm3.h>
+ preprocessor command.
+
+
+
+
+
+
#define
+
File
+
Value
+
Description
+
+
+
__NVIC_PRIO_BITS
+
core_cm0.h
+
(2)
+
Number of priority bits implemented in the NVIC (device specific)
+
+
+
__NVIC_PRIO_BITS
+
core_cm3.h
+
(2 ... 8)
+
Number of priority bits implemented in the NVIC (device specific)
+
+
+
__MPU_PRESENT
+
core_cm0.h, core_cm3.h
+
(0, 1)
+
Defines if an MPU is present or not
+
+
+
__Vendor_SysTickConfig
+
core_cm0.h, core_cm3.h
+
(1)
+
When this define is setup to 1, the SysTickConfig function
+ in core_cm3.h is excluded. In this case the device.h
+ file must contain a vendor specific implementation of this function.
+
+
+
+
+
+
Device Peripheral Access Layer
+
+ Each peripheral uses a prefix which consists of <device abbreviation>_
+ and <peripheral name>_ to identify peripheral registers that access this
+ specific peripheral. The intention of this is to avoid name collisions caused
+ due to short names. If more than one peripheral of the same type exists,
+ identifiers have a postfix (digit or letter). For example:
+
+
+
<device abbreviation>_UART_Type: defines the generic register layout for all UART channels in a device.
+
<device abbreviation>_UART1: is a pointer to a register structure that refers to a specific UART.
+ For example UART1->DR is the data register of UART1.
+
+ To access the peripheral registers and related function in a device the files device.h
+ and core_cm0.h / core_cm3.h defines as a minimum:
+
+
+
The Register Layout Typedef for each peripheral that defines all register names.
+ Names that start with RESERVE are used to introduce space into the structure to adjust the addresses of
+ the peripheral registers. For example:
+
+typedef struct {
+ __IO uint32_t CTRL; /* SysTick Control and Status Register */
+ __IO uint32_t LOAD; /* SysTick Reload Value Register */
+ __IO uint32_t VAL; /* SysTick Current Value Register */
+ __I uint32_t CALIB; /* SysTick Calibration Register */
+ } SysTick_Type;
+
+
+
+ Base Address for each peripheral (in case of multiple peripherals
+ that use the same register layout typedef multiple base addresses are defined). For example:
+
+#define SysTick_BASE (SCS_BASE + 0x0010) /* SysTick Base Address */
+
+
+
+ Access Definition for each peripheral (in case of multiple peripherals that use
+ the same register layout typedef multiple access definitions exist, i.e. LPC_UART0,
+ LPC_UART2). For Example:
+
+ These definitions allow to access the peripheral registers from user code with simple assignments like:
+
+
SysTick->CTRL = 0;
+
+
Optional Features
+
In addition the device.h file may define:
+
+
+ #define constants that simplify access to the peripheral registers.
+ These constant define bit-positions or other specific patterns are that required for the
+ programming of the peripheral registers. The identifiers used start with
+ <device abbreviation>_ and <peripheral name>_.
+ It is recommended to use CAPITAL letters for such #define constants.
+
+
+ Functions that perform more complex functions with the peripheral (i.e. status query before
+ a sending register is accessed). Again these function start with
+ <device abbreviation>_ and <peripheral name>_.
+
+
+
+
core_cm0.h and core_cm0.c
+
+ File core_cm0.h describes the data structures for the Cortex-M0 core peripherals and does
+ the address mapping of this structures. It also provides basic access to the Cortex-M0 core registers
+ and core peripherals with efficient functions (defined as static inline).
+
+
+ File core_cm0.c defines several helper functions that access processor registers.
+
+ File core_cm3.h describes the data structures for the Cortex-M3 core peripherals and does
+ the address mapping of this structures. It also provides basic access to the Cortex-M3 core registers
+ and core peripherals with efficient functions (defined as static inline).
+
+
+ File core_cm3.c defines several helper functions that access processor registers.
+
+ A template file for startup_device is provided by ARM for each supported
+ compiler. It is adapted by the silicon vendor to include interrupt vectors for all device specific
+ interrupt handlers. Each interrupt handler is defined as weak function
+ to an dummy handler. Therefore the interrupt handler can be directly used in application software
+ without any requirements to adapt the startup_device file.
+
+
+ The following exception names are fixed and define the start of the vector table for a Cortex-M0:
+
+ The user application may simply define an interrupt handler function by using the handler name
+ as shown below.
+
+
+void WWDG_IRQHandler(void)
+{
+ :
+ :
+}
+
+
+
system_device.c
+
+ A template file for system_device.c is provided by ARM but adapted by
+ the silicon vendor to match their actual device. As a minimum requirement
+ this file must provide a device specific system configuration function and a global variable
+ that contains the system frequency. It configures the device and initializes typically the
+ oscillator (PLL) that is part of the microcontroller device.
+
+
+ The file system_device.c must provide
+ as a minimum requirement the SystemInit function as shown below.
+
+
+
+
+
+
Function Definition
+
Description
+
+
+
void SystemInit (void)
+
Setup the microcontroller system. Typically this function configures the
+ oscillator (PLL) that is part of the microcontroller device. For systems
+ with variable clock speed it also updates the variable SystemCoreClock.
+ SystemInit is called from startup_device file.
+
+
+
void SystemCoreClockUpdate (void)
+
Updates the variable SystemCoreClock and must be called whenever the
+ core clock is changed during program execution. SystemCoreClockUpdate()
+ evaluates the clock register settings and calculates the current core clock.
+
+
+
+
+
+
+ Also part of the file system_device.c
+ is the variable SystemCoreClock which contains the current CPU clock speed shown below.
+
+
+
+
+
+
Variable Definition
+
Description
+
+
+
uint32_t SystemCoreClock
+
Contains the system core clock (which is the system clock frequency supplied
+ to the SysTick timer and the processor core clock). This variable can be
+ used by the user application to setup the SysTick timer or configure other
+ parameters. It may also be used by debugger to query the frequency of the
+ debug timer or configure the trace clock speed.
+ SystemCoreClock is initialized with a correct predefined value.
+ The compiler must be configured to avoid the removal of this variable in
+ case that the application program is not using it. It is important for
+ debug systems that the variable is physically present in memory so that
+ it can be examined to configure the debugger.
+
+
+
+
+
Note
+
+
The above definitions are the minimum requirements for the file
+ system_device.c. This
+ file may export more functions or variables that provide a more flexible
+ configuration of the microcontroller system.
+
+
+
+
+
Core Peripheral Access Layer
+
+
Cortex-M Core Register Access
+
+ The following functions are defined in core_cm0.h / core_cm3.h
+ and provide access to Cortex-M core registers.
+
+
+
+
+
+
Function Definition
+
Core
+
Core Register
+
Description
+
+
+
void __enable_irq (void)
+
M0, M3
+
PRIMASK = 0
+
Global Interrupt enable (using the instruction CPSIE
+ i)
+
+
+
void __disable_irq (void)
+
M0, M3
+
PRIMASK = 1
+
Global Interrupt disable (using the instruction
+ CPSID i)
+
+
+
void __set_PRIMASK (uint32_t value)
+
M0, M3
+
PRIMASK = value
+
Assign value to Priority Mask Register (using the instruction
+ MSR)
+
+
+
uint32_t __get_PRIMASK (void)
+
M0, M3
+
return PRIMASK
+
Return Priority Mask Register (using the instruction
+ MRS)
+
+
+
void __enable_fault_irq (void)
+
M3
+
FAULTMASK = 0
+
Global Fault exception and Interrupt enable (using the
+ instruction CPSIE
+ f)
+
+
+
void __disable_fault_irq (void)
+
M3
+
FAULTMASK = 1
+
Global Fault exception and Interrupt disable (using the
+ instruction CPSID f)
+
+
+
void __set_FAULTMASK (uint32_t value)
+
M3
+
FAULTMASK = value
+
Assign value to Fault Mask Register (using the instruction
+ MSR)
+
+
+
uint32_t __get_FAULTMASK (void)
+
M3
+
return FAULTMASK
+
Return Fault Mask Register (using the instruction MRS)
+
+
+
void __set_BASEPRI (uint32_t value)
+
M3
+
BASEPRI = value
+
Set Base Priority (using the instruction MSR)
+
+
+
uiuint32_t __get_BASEPRI (void)
+
M3
+
return BASEPRI
+
Return Base Priority (using the instruction MRS)
+
+
+
void __set_CONTROL (uint32_t value)
+
M0, M3
+
CONTROL = value
+
Set CONTROL register value (using the instruction MSR)
+
+
+
uint32_t __get_CONTROL (void)
+
M0, M3
+
return CONTROL
+
Return Control Register Value (using the instruction
+ MRS)
+
+
+
void __set_PSP (uint32_t TopOfProcStack)
+
M0, M3
+
PSP = TopOfProcStack
+
Set Process Stack Pointer value (using the instruction
+ MSR)
+
+
+
uint32_t __get_PSP (void)
+
M0, M3
+
return PSP
+
Return Process Stack Pointer (using the instruction MRS)
+
+
+
void __set_MSP (uint32_t TopOfMainStack)
+
M0, M3
+
MSP = TopOfMainStack
+
Set Main Stack Pointer (using the instruction MSR)
+
+
+
uint32_t __get_MSP (void)
+
M0, M3
+
return MSP
+
Return Main Stack Pointer (using the instruction MRS)
+
+
+
+
+
Cortex-M Instruction Access
+
+ The following functions are defined in core_cm0.h / core_cm3.hand
+ generate specific Cortex-M instructions. The functions are implemented in the file
+ core_cm0.c / core_cm3.c.
+
+
+
+
+
+
Name
+
Core
+
Generated CPU Instruction
+
Description
+
+
+
void __NOP (void)
+
M0, M3
+
NOP
+
No Operation
+
+
+
void __WFI (void)
+
M0, M3
+
WFI
+
Wait for Interrupt
+
+
+
void __WFE (void)
+
M0, M3
+
WFE
+
Wait for Event
+
+
+
void __SEV (void)
+
M0, M3
+
SEV
+
Set Event
+
+
+
void __ISB (void)
+
M0, M3
+
ISB
+
Instruction Synchronization Barrier
+
+
+
void __DSB (void)
+
M0, M3
+
DSB
+
Data Synchronization Barrier
+
+
+
void __DMB (void)
+
M0, M3
+
DMB
+
Data Memory Barrier
+
+
+
uint32_t __REV (uint32_t value)
+
M0, M3
+
REV
+
Reverse byte order in integer value.
+
+
+
uint32_t __REV16 (uint16_t value)
+
M0, M3
+
REV16
+
Reverse byte order in unsigned short value.
+
+
+
sint32_t __REVSH (sint16_t value)
+
M0, M3
+
REVSH
+
Reverse byte order in signed short value with sign extension to integer.
Remove the exclusive lock created by __LDREXB, __LDREXH, or __LDREXW
+
+
+
+
+
+
NVIC Access Functions
+
+ The CMSIS provides access to the NVIC via the register interface structure and several helper
+ functions that simplify the setup of the NVIC. The CMSIS HAL uses IRQ numbers (IRQn) to
+ identify the interrupts. The first device interrupt has the IRQn value 0. Therefore negative
+ IRQn values are used for processor core exceptions.
+
+
+ For the IRQn values of core exceptions the file device.h provides
+ the following enum names.
+
+
+
+
+
+
Core Exception enum Value
+
Core
+
IRQn
+
Description
+
+
+
NonMaskableInt_IRQn
+
M0, M3
+
-14
+
Cortex-M Non Maskable Interrupt
+
+
+
HardFault_IRQn
+
M0, M3
+
-13
+
Cortex-M Hard Fault Interrupt
+
+
+
MemoryManagement_IRQn
+
M3
+
-12
+
Cortex-M Memory Management Interrupt
+
+
+
BusFault_IRQn
+
M3
+
-11
+
Cortex-M Bus Fault Interrupt
+
+
+
UsageFault_IRQn
+
M3
+
-10
+
Cortex-M Usage Fault Interrupt
+
+
+
SVCall_IRQn
+
M0, M3
+
-5
+
Cortex-M SV Call Interrupt
+
+
+
DebugMonitor_IRQn
+
M3
+
-4
+
Cortex-M Debug Monitor Interrupt
+
+
+
PendSV_IRQn
+
M0, M3
+
-2
+
Cortex-M Pend SV Interrupt
+
+
+
SysTick_IRQn
+
M0, M3
+
-1
+
Cortex-M System Tick Interrupt
+
+
+
+
+
The following functions simplify the setup of the NVIC.
+The functions are defined as static inline.
IRQ Number, Priority, pointer to Priority Group, pointer to Preemptive Priority, pointer to Sub Priority
+
Deccode given priority to group, preemptive and sub priority
+
+
+
void NVIC_SystemReset (void)
+
M0, M3
+
(void)
+
Resets the System
+
+
+
+
Note
+
+
The processor exceptions have negative enum values. Device specific interrupts
+ have positive enum values and start with 0. The values are defined in
+ device.h file.
+
+
+
The values for PreemptPriority and SubPriority
+ used in functions NVIC_EncodePriority and NVIC_DecodePriority
+ depend on the available __NVIC_PRIO_BITS implemented in the NVIC.
+
+
+
+
+
+
SysTick Configuration Function
+
+
The following function is used to configure the SysTick timer and start the
+SysTick interrupt.
+
+
+
+
+
Name
+
Parameter
+
Description
+
+
+
uint32_t SysTickConfig
+ (uint32_t ticks)
+
ticks is SysTick counter reload value
+
Setup the SysTick timer and enable the SysTick interrupt. After this
+ call the SysTick timer creates interrupts with the specified time
+ interval.
+
+ Return: 0 when successful, 1 on failure.
+
+
+
+
+
+
+
Cortex-M3 ITM Debug Access
+
+
The Cortex-M3 incorporates the Instrumented Trace Macrocell (ITM) that
+provides together with the Serial Viewer Output trace capabilities for the
+microcontroller system. The ITM has 32 communication channels; two ITM
+communication channels are used by CMSIS to output the following information:
+
+
ITM Channel 0: implements the ITM_SendChar function
+ which can be used for printf-style output via the debug interface.
+
ITM Channel 31: is reserved for the RTOS kernel and can be used for
+ kernel awareness debugging.
+
+
Note
+
+
The ITM channel 31 is selected for the RTOS kernel since some kernels
+ may use the Privileged level for program execution. ITM
+ channels have 4 groups with 8 channels each, whereby each group can be
+ configured for access rights in the Unprivileged level. The ITM channel 0
+ may be therefore enabled for the user task whereas ITM channel 31 may be
+ accessible only in Privileged level from the RTOS kernel itself.
+
+
+
+
The prototype of the ITM_SendChar routine is shown in the
+table below.
+
+
+
+
+
Name
+
Parameter
+
Description
+
+
+
void uint32_t ITM_SendChar(uint32_t chr)
+
character to output
+
The function outputs a character via the ITM channel 0. The
+ function returns when no debugger is connected that has booked the
+ output. It is blocking when a debugger is connected, but the
+ previous character send is not transmitted.
+ Return: the input character 'chr'.
+
+
+
+
+
+ Example for the usage of the ITM Channel 31 for RTOS Kernels:
+
+
+ // check if debugger connected and ITM channel enabled for tracing
+ if ((CoreDebug->DEMCR & CoreDebug_DEMCR_TRCENA) &&
+ (ITM->TCR & ITM_TCR_ITMENA) &&
+ (ITM->TER & (1UL << 31))) {
+ // transmit trace data
+ while (ITM->PORT31_U32 == 0);
+ ITM->PORT[31].u8 = task_id; // id of next task
+ while (ITM->PORT[31].u32 == 0);
+ ITM->PORT[31].u32 = task_status; // status information
+ }
+
+
+
Cortex-M3 additional Debug Access
+
+
CMSIS provides additional debug functions to enlarge the Cortex-M3 Debug Access.
+Data can be transmitted via a certain global buffer variable towards the target system.
+
+
The buffer variable and the prototypes of the additional functions are shown in the
+table below.
+
+
+
+
+
Name
+
Parameter
+
Description
+
+
+
extern volatile int ITM_RxBuffer
+
+
Buffer to transmit data towards debug system.
+ Value 0x5AA55AA5 indicates that buffer is empty.
+
+
+
int ITM_ReceiveChar (void)
+
none
+
The nonblocking functions returns the character stored in
+ ITM_RxBuffer.
+ Return: -1 indicates that no character was received.
+
+
+
int ITM_CheckChar (void)
+
none
+
The function checks if a character is available in ITM_RxBuffer.
+ Return: 1 indicates that a character is available, 0 indicates that
+ no character is available.
+
+
+
+
+
+
CMSIS Example
+
+ The following section shows a typical example for using the CMSIS layer in user applications.
+ The example is based on a STM32F10x Device.
+
+
+#include "stm32f10x.h"
+
+volatile uint32_t msTicks; /* timeTicks counter */
+
+void SysTick_Handler(void) {
+ msTicks++; /* increment timeTicks counter */
+}
+
+__INLINE static void Delay (uint32_t dlyTicks) {
+ uint32_t curTicks = msTicks;
+
+ while ((msTicks - curTicks) < dlyTicks);
+}
+
+__INLINE static void LED_Config(void) {
+ ; /* Configure the LEDs */
+}
+
+__INLINE static void LED_On (uint32_t led) {
+ ; /* Turn On LED */
+}
+
+__INLINE static void LED_Off (uint32_t led) {
+ ; /* Turn Off LED */
+}
+
+int main (void) {
+ if (SysTick_Config (SystemCoreClock / 1000)) { /* Setup SysTick for 1 msec interrupts */
+ ; /* Handle Error */
+ while (1);
+ }
+
+ LED_Config(); /* configure the LEDs */
+
+ while(1) {
+ LED_On (0x100); /* Turn on the LED */
+ Delay (100); /* delay 100 Msec */
+ LED_Off (0x100); /* Turn off the LED */
+ Delay (100); /* delay 100 Msec */
+ }
+}
+
+
+
\ No newline at end of file
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/License.doc b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/License.doc
new file mode 100644
index 00000000..b6b8acec
Binary files /dev/null and b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/CMSIS/License.doc differ
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/Release_Notes.html b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/Release_Notes.html
new file mode 100644
index 00000000..633e42e3
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/Release_Notes.html
@@ -0,0 +1,342 @@
+
+
+
+
+
+
+
+
+
+
+
+
+Release Notes for STM32F10x Standard Peripherals Library Drivers
+
+
+
+
+
+
STM32F10x Standard
+Peripherals Library Drivers update History
+
V3.5.0 / 11-March-2011
+
Main
+Changes
+
+
+
stm32f10x_can.h/.c files:
+
+
Add 5 new functions
+
+
3
+new functions controlling the counter errors: CAN_GetLastErrorCode(),
+CAN_GetReceiveErrorCounter() and CAN_GetLSBTransmitErrorCounter().
+
+
+
1 new function to select the CAN operating mode: CAN_OperatingModeRequest().
+
+
+
1 new function to support CAN TT mode: CAN_TTComModeCmd().
+
+
+
CAN_TransmitStatus() function updated to support all CAN transmit intermediate states
+
+
+
stm32f10x_i2c.h/.c files:
+
+
Add 1 new function:
+
+
I2C_NACKPositionConfig():
+This function configures the same bit (POS) as I2C_PECPositionConfig()
+but is intended to be used in I2C mode while I2C_PECPositionConfig() is
+intended to used in SMBUS mode.
+
+
+
stm32f10x_tim.h/.c files:
+
+
Change the TIM_DMABurstLength_xBytes definitions to TIM_DMABurstLength_xTansfers
+
+
+
+
+
+
+
3.4.0
+- 10/15/2010
+
+
+
General
+
+
+
+
Add support for STM32F10x High-density value line devices.
+
+
+
+
STM32F10x_StdPeriph_Driver
+
+
+
+
+
+
stm32f10x_bkp.h/.c
+
+
Delete BKP registers definition from stm32f10x_bkp.c and use defines within stm32f10x.h file.
+
+
stm32f10x_can.h/.c
+
+
Delete CAN registers definition from stm32f10x_can.c and use defines within stm32f10x.h file.
+
+
Update the wording of some defines and Asserts macro.
+
+
CAN_GetFlagStatus()
+and CAN_ClearFlag() functions: updated to support new flags (were not
+supported in previous version). These flags are: CAN_FLAG_RQCP0,
+CAN_FLAG_RQCP1, CAN_FLAG_RQCP2, CAN_FLAG_FMP1, CAN_FLAG_FF1,
+CAN_FLAG_FOV1, CAN_FLAG_FMP0, CAN_FLAG_FF0, CAN_FLAG_FOV0,
+CAN_FLAG_WKU, CAN_FLAG_SLAK and CAN_FLAG_LEC.
+
+
CAN_GetITStatus()
+function: add a check of the interrupt enable bit before getting the
+status of corresponding interrupt pending bit.
+
+
CAN_ClearITPendingBit() function: correct the procedure to clear the interrupt pending bit.
+
+
+
stm32f10x_crc.h/.c
+
+
Delete CRC registers definition from stm32f10x_crc.c and use defines within stm32f10x.h file.
+
+
stm32f10x_dac.h/.c
+
+
Delete DAC registers definition from stm32f10x_dac.c and use defines within stm32f10x.h file.
+
+
stm32f10x_dbgmcu.h/.c
+
+
Delete DBGMCU registers definition from stm32f10x_dbgmcu.c and use defines within stm32f10x.h file.
+
+
stm32f10x_dma.h/.c
+
+
Delete DMA registers definition from stm32f10x_dma.c and use defines within stm32f10x.h file.
+
Add new function "void DMA_SetCurrDataCounter(DMA_Channel_TypeDef* DMAy_Channelx, uint16_t DataNumber);"
+
+
+
stm32f10x_flash.h/.c
+
+
FLASH functions (Erase and Program) updated to always clear the "PG", "MER" and "PER" bits even in case of TimeOut Error.
+
+
stm32f10x_fsmc.h/.c
+
+
Add new member "FSMC_AsynchronousWait" in "FSMC_NORSRAMInitTypeDef" structure.
+
+
stm32f10x_gpio.h/.c
+
+
GPIO_PinRemapConfig() function: add new values for GPIO_Remap parameter, to support new remap for TIM6, TIM7 and DAC DMA requests, TIM12 and DAC Triggers / DMA2_Channel5 Interrupt mapping.
+
+
stm32f10x_pwr.h/.c
+
+
Delete PWR registers definition from stm32f10x_pwr.c and use defines within stm32f10x.h and core_cm3.h files.
+
+
stm32f10x_rtc.h/.c
+
+
Delete RTC registers definition from stm32f10x_rtc.c and use defines within stm32f10x.h file.
+
+
stm32f10x_spi.h/.c
+
+
Add new definition for I2S Audio Clock frequencies "I2S_AudioFreq_192k".
+
+
stm32f10x_tim.h/.c
+
Add new definition for TIM Input Capture Polarity "TIM_ICPolarity_BothEdge".
+
+
+
+
3.3.0
+- 04/16/2010
+
+
General
+
Add support for STM32F10x XL-density devices.
I2C driver: events description and management enhancement.
+
STM32F10x_StdPeriph_Driver
+
stm32f10x_dbgmcu.h/.c
DBGMCU_Config() function: add new values DBGMCU_TIMx_STOP (x: 9..14) for DBGMCU_Periph parameter.
stm32f10x_flash.h/.c:
+updated to support Bank2 of XL-density devices (up to 1MByte of Flash
+memory). For more details, refer to the description provided within
+stm32f10x_flash.c file.
stm32f10x_gpio.h/.c
GPIO_PinRemapConfig() function: add new values for GPIO_Remap parameter, to support new remap for FSMC_NADV pin and TIM9..11,13,14.
stm32f10x_i2c.h/.c: I2C events description and management enhancement.
I2C_CheckEvent()
+function: updated to check whether the last event contains the
+I2C_EVENT (instead of check whether the last event is equal to
+I2C_EVENT)
Add
+detailed description of I2C events and how to manage them using the
+functions provided by this driver. For more information, refer to
+stm32f10x_i2c.h and stm32f10x_i2c.c files.
stm32f10x_rcc.h/.c: updated to support TIM9..TIM14 APB clock and reset configuration
stm32f10x_tim.h/.c: updated to support new Timers TIM9..TIM14.
Add support
+for STM32 Low-density Value line (STM32F100x4/6) and
+Medium-density Value line (STM32F100x8/B) devices.
+
Almost
+peripherals drivers were updated to support Value
+line devices features
+
Drivers limitations fix and enhancements.
+
+
+
+
STM32F10x_StdPeriph_Driver
+
+
+
Add new
+firmware driver for CEC peripheral: stm32f10x_cec.h and stm32f10x_cec.c
+
Timers drivers stm32f10x_tim.h/.c: add support for new General Purpose Timers: TIM15, TIM16 and TIM17.
+
RCC driver: add support for new Value peripherals: HDMI-CEC, TIM15, TIM16 and TIM17.
+
GPIO driver: add new remap parameters for TIM1, TIM15, TIM16, TIM17 and HDMI-CEC: GPIO_Remap_TIM1_DMA, GPIO_Remap_TIM15, GPIO_Remap_TIM16, GPIO_Remap_TIM17, GPIO_Remap_CEC.
+
USART
+driver: add support for Oversampling by 8 mode and onebit method. 2
+functions has been added: USART_OverSampling8Cmd() and
+USART_OneBitMethodCmd().
+
+
DAC
+driver: add new functions handling the DAC under run feature:
+DAC_ITConfig(), DAC_GetFlagStatus(), DAC_ClearFlag(), DAC_GetITStatus()
+and DAC_ClearITPendingBit().
+
DBGMCU driver: add new parameters for TIM15, TIM16 and TIM17: DBGMCU_TIM15_STOP, DBGMCU_TIM16_STOP, DBGMCU_TIM17_STOP.
+
+
FLASH
+driver: the FLASH_EraseOptionBytes() function updated. This is now just
+erasing the option bytes without modifying the RDP status either
+enabled or disabled.
+
PWR
+driver: the PWR_EnterSTOPMode() function updated. When woken up from
+STOP mode, this function resets again the SLEEPDEEP bit in the
+Cortex-M3 System Control register to allow Sleep mode entering.
+
+
+
+
License
+
The
+enclosed firmware and all the related documentation are not covered by
+a License Agreement, if you need such License you can contact your
+local STMicroelectronics office.
+
THE
+PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO
+SAVE TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR
+ANY DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY
+CLAIMS ARISING FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY
+CUSTOMERS OF THE CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH
+THEIR PRODUCTS.
+
+
+
+
For
+complete documentation on STM32(CORTEX M3) 32-Bit Microcontrollers
+visit www.st.com/STM32
+
+
+
+
+
+
+
+
+
+
+
+
+
\ No newline at end of file
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_gpio.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_gpio.h
new file mode 100644
index 00000000..b8aa49a2
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_gpio.h
@@ -0,0 +1,385 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x_gpio.h
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief This file contains all the functions prototypes for the GPIO
+ * firmware library.
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_usart.h"
+#include "stm32f10x_rcc.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup USART
+ * @brief USART driver modules
+ * @{
+ */
+
+/** @defgroup USART_Private_TypesDefinitions
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Defines
+ * @{
+ */
+
+#define CR1_UE_Set ((uint16_t)0x2000) /*!< USART Enable Mask */
+#define CR1_UE_Reset ((uint16_t)0xDFFF) /*!< USART Disable Mask */
+
+#define CR1_WAKE_Mask ((uint16_t)0xF7FF) /*!< USART WakeUp Method Mask */
+
+#define CR1_RWU_Set ((uint16_t)0x0002) /*!< USART mute mode Enable Mask */
+#define CR1_RWU_Reset ((uint16_t)0xFFFD) /*!< USART mute mode Enable Mask */
+#define CR1_SBK_Set ((uint16_t)0x0001) /*!< USART Break Character send Mask */
+#define CR1_CLEAR_Mask ((uint16_t)0xE9F3) /*!< USART CR1 Mask */
+#define CR2_Address_Mask ((uint16_t)0xFFF0) /*!< USART address Mask */
+
+#define CR2_LINEN_Set ((uint16_t)0x4000) /*!< USART LIN Enable Mask */
+#define CR2_LINEN_Reset ((uint16_t)0xBFFF) /*!< USART LIN Disable Mask */
+
+#define CR2_LBDL_Mask ((uint16_t)0xFFDF) /*!< USART LIN Break detection Mask */
+#define CR2_STOP_CLEAR_Mask ((uint16_t)0xCFFF) /*!< USART CR2 STOP Bits Mask */
+#define CR2_CLOCK_CLEAR_Mask ((uint16_t)0xF0FF) /*!< USART CR2 Clock Mask */
+
+#define CR3_SCEN_Set ((uint16_t)0x0020) /*!< USART SC Enable Mask */
+#define CR3_SCEN_Reset ((uint16_t)0xFFDF) /*!< USART SC Disable Mask */
+
+#define CR3_NACK_Set ((uint16_t)0x0010) /*!< USART SC NACK Enable Mask */
+#define CR3_NACK_Reset ((uint16_t)0xFFEF) /*!< USART SC NACK Disable Mask */
+
+#define CR3_HDSEL_Set ((uint16_t)0x0008) /*!< USART Half-Duplex Enable Mask */
+#define CR3_HDSEL_Reset ((uint16_t)0xFFF7) /*!< USART Half-Duplex Disable Mask */
+
+#define CR3_IRLP_Mask ((uint16_t)0xFFFB) /*!< USART IrDA LowPower mode Mask */
+#define CR3_CLEAR_Mask ((uint16_t)0xFCFF) /*!< USART CR3 Mask */
+
+#define CR3_IREN_Set ((uint16_t)0x0002) /*!< USART IrDA Enable Mask */
+#define CR3_IREN_Reset ((uint16_t)0xFFFD) /*!< USART IrDA Disable Mask */
+#define GTPR_LSB_Mask ((uint16_t)0x00FF) /*!< Guard Time Register LSB Mask */
+#define GTPR_MSB_Mask ((uint16_t)0xFF00) /*!< Guard Time Register MSB Mask */
+#define IT_Mask ((uint16_t)0x001F) /*!< USART Interrupt Mask */
+
+/* USART OverSampling-8 Mask */
+#define CR1_OVER8_Set ((u16)0x8000) /* USART OVER8 mode Enable Mask */
+#define CR1_OVER8_Reset ((u16)0x7FFF) /* USART OVER8 mode Disable Mask */
+
+/* USART One Bit Sampling Mask */
+#define CR3_ONEBITE_Set ((u16)0x0800) /* USART ONEBITE mode Enable Mask */
+#define CR3_ONEBITE_Reset ((u16)0xF7FF) /* USART ONEBITE mode Disable Mask */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Variables
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_FunctionPrototypes
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Functions
+ * @{
+ */
+
+/**
+ * @brief Deinitializes the USARTx peripheral registers to their default reset values.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @retval None
+ */
+void USART_DeInit(USART_TypeDef* USARTx)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+
+ if (USARTx == USART1)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, DISABLE);
+ }
+ else if (USARTx == USART2)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART2, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART2, DISABLE);
+ }
+ else if (USARTx == USART3)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART3, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART3, DISABLE);
+ }
+ else if (USARTx == UART4)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART4, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART4, DISABLE);
+ }
+ else
+ {
+ if (USARTx == UART5)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART5, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART5, DISABLE);
+ }
+ }
+}
+
+/**
+ * @brief Initializes the USARTx peripheral according to the specified
+ * parameters in the USART_InitStruct .
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_InitStruct: pointer to a USART_InitTypeDef structure
+ * that contains the configuration information for the specified USART
+ * peripheral.
+ * @retval None
+ */
+void USART_Init(USART_TypeDef* USARTx, USART_InitTypeDef* USART_InitStruct)
+{
+ uint32_t tmpreg = 0x00, apbclock = 0x00;
+ uint32_t integerdivider = 0x00;
+ uint32_t fractionaldivider = 0x00;
+ uint32_t usartxbase = 0;
+ RCC_ClocksTypeDef RCC_ClocksStatus;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_BAUDRATE(USART_InitStruct->USART_BaudRate));
+ assert_param(IS_USART_WORD_LENGTH(USART_InitStruct->USART_WordLength));
+ assert_param(IS_USART_STOPBITS(USART_InitStruct->USART_StopBits));
+ assert_param(IS_USART_PARITY(USART_InitStruct->USART_Parity));
+ assert_param(IS_USART_MODE(USART_InitStruct->USART_Mode));
+ assert_param(IS_USART_HARDWARE_FLOW_CONTROL(USART_InitStruct->USART_HardwareFlowControl));
+ /* The hardware flow control is available only for USART1, USART2 and USART3 */
+ if (USART_InitStruct->USART_HardwareFlowControl != USART_HardwareFlowControl_None)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ usartxbase = (uint32_t)USARTx;
+
+/*---------------------------- USART CR2 Configuration -----------------------*/
+ tmpreg = USARTx->CR2;
+ /* Clear STOP[13:12] bits */
+ tmpreg &= CR2_STOP_CLEAR_Mask;
+ /* Configure the USART Stop Bits, Clock, CPOL, CPHA and LastBit ------------*/
+ /* Set STOP[13:12] bits according to USART_StopBits value */
+ tmpreg |= (uint32_t)USART_InitStruct->USART_StopBits;
+
+ /* Write to USART CR2 */
+ USARTx->CR2 = (uint16_t)tmpreg;
+
+/*---------------------------- USART CR1 Configuration -----------------------*/
+ tmpreg = USARTx->CR1;
+ /* Clear M, PCE, PS, TE and RE bits */
+ tmpreg &= CR1_CLEAR_Mask;
+ /* Configure the USART Word Length, Parity and mode ----------------------- */
+ /* Set the M bits according to USART_WordLength value */
+ /* Set PCE and PS bits according to USART_Parity value */
+ /* Set TE and RE bits according to USART_Mode value */
+ tmpreg |= (uint32_t)USART_InitStruct->USART_WordLength | USART_InitStruct->USART_Parity |
+ USART_InitStruct->USART_Mode;
+ /* Write to USART CR1 */
+ USARTx->CR1 = (uint16_t)tmpreg;
+
+/*---------------------------- USART CR3 Configuration -----------------------*/
+ tmpreg = USARTx->CR3;
+ /* Clear CTSE and RTSE bits */
+ tmpreg &= CR3_CLEAR_Mask;
+ /* Configure the USART HFC -------------------------------------------------*/
+ /* Set CTSE and RTSE bits according to USART_HardwareFlowControl value */
+ tmpreg |= USART_InitStruct->USART_HardwareFlowControl;
+ /* Write to USART CR3 */
+ USARTx->CR3 = (uint16_t)tmpreg;
+
+/*---------------------------- USART BRR Configuration -----------------------*/
+ /* Configure the USART Baud Rate -------------------------------------------*/
+ RCC_GetClocksFreq(&RCC_ClocksStatus);
+ if (usartxbase == USART1_BASE)
+ {
+ apbclock = RCC_ClocksStatus.PCLK2_Frequency;
+ }
+ else
+ {
+ apbclock = RCC_ClocksStatus.PCLK1_Frequency;
+ }
+
+ /* Determine the integer part */
+ if ((USARTx->CR1 & CR1_OVER8_Set) != 0)
+ {
+ /* Integer part computing in case Oversampling mode is 8 Samples */
+ integerdivider = ((25 * apbclock) / (2 * (USART_InitStruct->USART_BaudRate)));
+ }
+ else /* if ((USARTx->CR1 & CR1_OVER8_Set) == 0) */
+ {
+ /* Integer part computing in case Oversampling mode is 16 Samples */
+ integerdivider = ((25 * apbclock) / (4 * (USART_InitStruct->USART_BaudRate)));
+ }
+ tmpreg = (integerdivider / 100) << 4;
+
+ /* Determine the fractional part */
+ fractionaldivider = integerdivider - (100 * (tmpreg >> 4));
+
+ /* Implement the fractional part in the register */
+ if ((USARTx->CR1 & CR1_OVER8_Set) != 0)
+ {
+ tmpreg |= ((((fractionaldivider * 8) + 50) / 100)) & ((uint8_t)0x07);
+ }
+ else /* if ((USARTx->CR1 & CR1_OVER8_Set) == 0) */
+ {
+ tmpreg |= ((((fractionaldivider * 16) + 50) / 100)) & ((uint8_t)0x0F);
+ }
+
+ /* Write to USART BRR */
+ USARTx->BRR = (uint16_t)tmpreg;
+}
+
+/**
+ * @brief Fills each USART_InitStruct member with its default value.
+ * @param USART_InitStruct: pointer to a USART_InitTypeDef structure
+ * which will be initialized.
+ * @retval None
+ */
+void USART_StructInit(USART_InitTypeDef* USART_InitStruct)
+{
+ /* USART_InitStruct members default value */
+ USART_InitStruct->USART_BaudRate = 9600;
+ USART_InitStruct->USART_WordLength = USART_WordLength_8b;
+ USART_InitStruct->USART_StopBits = USART_StopBits_1;
+ USART_InitStruct->USART_Parity = USART_Parity_No ;
+ USART_InitStruct->USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
+ USART_InitStruct->USART_HardwareFlowControl = USART_HardwareFlowControl_None;
+}
+
+/**
+ * @brief Initializes the USARTx peripheral Clock according to the
+ * specified parameters in the USART_ClockInitStruct .
+ * @param USARTx: where x can be 1, 2, 3 to select the USART peripheral.
+ * @param USART_ClockInitStruct: pointer to a USART_ClockInitTypeDef
+ * structure that contains the configuration information for the specified
+ * USART peripheral.
+ * @note The Smart Card and Synchronous modes are not available for UART4 and UART5.
+ * @retval None
+ */
+void USART_ClockInit(USART_TypeDef* USARTx, USART_ClockInitTypeDef* USART_ClockInitStruct)
+{
+ uint32_t tmpreg = 0x00;
+ /* Check the parameters */
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ assert_param(IS_USART_CLOCK(USART_ClockInitStruct->USART_Clock));
+ assert_param(IS_USART_CPOL(USART_ClockInitStruct->USART_CPOL));
+ assert_param(IS_USART_CPHA(USART_ClockInitStruct->USART_CPHA));
+ assert_param(IS_USART_LASTBIT(USART_ClockInitStruct->USART_LastBit));
+
+/*---------------------------- USART CR2 Configuration -----------------------*/
+ tmpreg = USARTx->CR2;
+ /* Clear CLKEN, CPOL, CPHA and LBCL bits */
+ tmpreg &= CR2_CLOCK_CLEAR_Mask;
+ /* Configure the USART Clock, CPOL, CPHA and LastBit ------------*/
+ /* Set CLKEN bit according to USART_Clock value */
+ /* Set CPOL bit according to USART_CPOL value */
+ /* Set CPHA bit according to USART_CPHA value */
+ /* Set LBCL bit according to USART_LastBit value */
+ tmpreg |= (uint32_t)USART_ClockInitStruct->USART_Clock | USART_ClockInitStruct->USART_CPOL |
+ USART_ClockInitStruct->USART_CPHA | USART_ClockInitStruct->USART_LastBit;
+ /* Write to USART CR2 */
+ USARTx->CR2 = (uint16_t)tmpreg;
+}
+
+/**
+ * @brief Fills each USART_ClockInitStruct member with its default value.
+ * @param USART_ClockInitStruct: pointer to a USART_ClockInitTypeDef
+ * structure which will be initialized.
+ * @retval None
+ */
+void USART_ClockStructInit(USART_ClockInitTypeDef* USART_ClockInitStruct)
+{
+ /* USART_ClockInitStruct members default value */
+ USART_ClockInitStruct->USART_Clock = USART_Clock_Disable;
+ USART_ClockInitStruct->USART_CPOL = USART_CPOL_Low;
+ USART_ClockInitStruct->USART_CPHA = USART_CPHA_1Edge;
+ USART_ClockInitStruct->USART_LastBit = USART_LastBit_Disable;
+}
+
+/**
+ * @brief Enables or disables the specified USART peripheral.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USARTx peripheral.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_Cmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected USART by setting the UE bit in the CR1 register */
+ USARTx->CR1 |= CR1_UE_Set;
+ }
+ else
+ {
+ /* Disable the selected USART by clearing the UE bit in the CR1 register */
+ USARTx->CR1 &= CR1_UE_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the specified USART interrupts.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_IT: specifies the USART interrupt sources to be enabled or disabled.
+ * This parameter can be one of the following values:
+ * @arg USART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg USART_IT_LBD: LIN Break detection interrupt
+ * @arg USART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg USART_IT_TC: Transmission complete interrupt
+ * @arg USART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg USART_IT_IDLE: Idle line detection interrupt
+ * @arg USART_IT_PE: Parity Error interrupt
+ * @arg USART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @param NewState: new state of the specified USARTx interrupts.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_ITConfig(USART_TypeDef* USARTx, uint16_t USART_IT, FunctionalState NewState)
+{
+ uint32_t usartreg = 0x00, itpos = 0x00, itmask = 0x00;
+ uint32_t usartxbase = 0x00;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_CONFIG_IT(USART_IT));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ /* The CTS interrupt is not available for UART4 and UART5 */
+ if (USART_IT == USART_IT_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ usartxbase = (uint32_t)USARTx;
+
+ /* Get the USART register index */
+ usartreg = (((uint8_t)USART_IT) >> 0x05);
+
+ /* Get the interrupt position */
+ itpos = USART_IT & IT_Mask;
+ itmask = (((uint32_t)0x01) << itpos);
+
+ if (usartreg == 0x01) /* The IT is in CR1 register */
+ {
+ usartxbase += 0x0C;
+ }
+ else if (usartreg == 0x02) /* The IT is in CR2 register */
+ {
+ usartxbase += 0x10;
+ }
+ else /* The IT is in CR3 register */
+ {
+ usartxbase += 0x14;
+ }
+ if (NewState != DISABLE)
+ {
+ *(__IO uint32_t*)usartxbase |= itmask;
+ }
+ else
+ {
+ *(__IO uint32_t*)usartxbase &= ~itmask;
+ }
+}
+
+/**
+ * @brief Enables or disables the USART’s DMA interface.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_DMAReq: specifies the DMA request.
+ * This parameter can be any combination of the following values:
+ * @arg USART_DMAReq_Tx: USART DMA transmit request
+ * @arg USART_DMAReq_Rx: USART DMA receive request
+ * @param NewState: new state of the DMA Request sources.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note The DMA mode is not available for UART5 except in the STM32
+ * High density value line devices(STM32F10X_HD_VL).
+ * @retval None
+ */
+void USART_DMACmd(USART_TypeDef* USARTx, uint16_t USART_DMAReq, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_DMAREQ(USART_DMAReq));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the DMA transfer for selected requests by setting the DMAT and/or
+ DMAR bits in the USART CR3 register */
+ USARTx->CR3 |= USART_DMAReq;
+ }
+ else
+ {
+ /* Disable the DMA transfer for selected requests by clearing the DMAT and/or
+ DMAR bits in the USART CR3 register */
+ USARTx->CR3 &= (uint16_t)~USART_DMAReq;
+ }
+}
+
+/**
+ * @brief Sets the address of the USART node.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_Address: Indicates the address of the USART node.
+ * @retval None
+ */
+void USART_SetAddress(USART_TypeDef* USARTx, uint8_t USART_Address)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_ADDRESS(USART_Address));
+
+ /* Clear the USART address */
+ USARTx->CR2 &= CR2_Address_Mask;
+ /* Set the USART address node */
+ USARTx->CR2 |= USART_Address;
+}
+
+/**
+ * @brief Selects the USART WakeUp method.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_WakeUp: specifies the USART wakeup method.
+ * This parameter can be one of the following values:
+ * @arg USART_WakeUp_IdleLine: WakeUp by an idle line detection
+ * @arg USART_WakeUp_AddressMark: WakeUp by an address mark
+ * @retval None
+ */
+void USART_WakeUpConfig(USART_TypeDef* USARTx, uint16_t USART_WakeUp)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_WAKEUP(USART_WakeUp));
+
+ USARTx->CR1 &= CR1_WAKE_Mask;
+ USARTx->CR1 |= USART_WakeUp;
+}
+
+/**
+ * @brief Determines if the USART is in mute mode or not.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART mute mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_ReceiverWakeUpCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the USART mute mode by setting the RWU bit in the CR1 register */
+ USARTx->CR1 |= CR1_RWU_Set;
+ }
+ else
+ {
+ /* Disable the USART mute mode by clearing the RWU bit in the CR1 register */
+ USARTx->CR1 &= CR1_RWU_Reset;
+ }
+}
+
+/**
+ * @brief Sets the USART LIN Break detection length.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_LINBreakDetectLength: specifies the LIN break detection length.
+ * This parameter can be one of the following values:
+ * @arg USART_LINBreakDetectLength_10b: 10-bit break detection
+ * @arg USART_LINBreakDetectLength_11b: 11-bit break detection
+ * @retval None
+ */
+void USART_LINBreakDetectLengthConfig(USART_TypeDef* USARTx, uint16_t USART_LINBreakDetectLength)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_LIN_BREAK_DETECT_LENGTH(USART_LINBreakDetectLength));
+
+ USARTx->CR2 &= CR2_LBDL_Mask;
+ USARTx->CR2 |= USART_LINBreakDetectLength;
+}
+
+/**
+ * @brief Enables or disables the USART’s LIN mode.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART LIN mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_LINCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the LIN mode by setting the LINEN bit in the CR2 register */
+ USARTx->CR2 |= CR2_LINEN_Set;
+ }
+ else
+ {
+ /* Disable the LIN mode by clearing the LINEN bit in the CR2 register */
+ USARTx->CR2 &= CR2_LINEN_Reset;
+ }
+}
+
+/**
+ * @brief Transmits single data through the USARTx peripheral.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param Data: the data to transmit.
+ * @retval None
+ */
+void USART_SendData(USART_TypeDef* USARTx, uint16_t Data)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_DATA(Data));
+
+ /* Transmit Data */
+ USARTx->DR = (Data & (uint16_t)0x01FF);
+}
+
+/**
+ * @brief Returns the most recent received data by the USARTx peripheral.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @retval The received data.
+ */
+uint16_t USART_ReceiveData(USART_TypeDef* USARTx)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+
+ /* Receive Data */
+ return (uint16_t)(USARTx->DR & (uint16_t)0x01FF);
+}
+
+/**
+ * @brief Transmits break characters.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @retval None
+ */
+void USART_SendBreak(USART_TypeDef* USARTx)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+
+ /* Send break characters */
+ USARTx->CR1 |= CR1_SBK_Set;
+}
+
+/**
+ * @brief Sets the specified USART guard time.
+ * @param USARTx: where x can be 1, 2 or 3 to select the USART peripheral.
+ * @param USART_GuardTime: specifies the guard time.
+ * @note The guard time bits are not available for UART4 and UART5.
+ * @retval None
+ */
+void USART_SetGuardTime(USART_TypeDef* USARTx, uint8_t USART_GuardTime)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_123_PERIPH(USARTx));
+
+ /* Clear the USART Guard time */
+ USARTx->GTPR &= GTPR_LSB_Mask;
+ /* Set the USART guard time */
+ USARTx->GTPR |= (uint16_t)((uint16_t)USART_GuardTime << 0x08);
+}
+
+/**
+ * @brief Sets the system clock prescaler.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_Prescaler: specifies the prescaler clock.
+ * @note The function is used for IrDA mode with UART4 and UART5.
+ * @retval None
+ */
+void USART_SetPrescaler(USART_TypeDef* USARTx, uint8_t USART_Prescaler)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+
+ /* Clear the USART prescaler */
+ USARTx->GTPR &= GTPR_MSB_Mask;
+ /* Set the USART prescaler */
+ USARTx->GTPR |= USART_Prescaler;
+}
+
+/**
+ * @brief Enables or disables the USART’s Smart Card mode.
+ * @param USARTx: where x can be 1, 2 or 3 to select the USART peripheral.
+ * @param NewState: new state of the Smart Card mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note The Smart Card mode is not available for UART4 and UART5.
+ * @retval None
+ */
+void USART_SmartCardCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the SC mode by setting the SCEN bit in the CR3 register */
+ USARTx->CR3 |= CR3_SCEN_Set;
+ }
+ else
+ {
+ /* Disable the SC mode by clearing the SCEN bit in the CR3 register */
+ USARTx->CR3 &= CR3_SCEN_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables NACK transmission.
+ * @param USARTx: where x can be 1, 2 or 3 to select the USART peripheral.
+ * @param NewState: new state of the NACK transmission.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note The Smart Card mode is not available for UART4 and UART5.
+ * @retval None
+ */
+void USART_SmartCardNACKCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the NACK transmission by setting the NACK bit in the CR3 register */
+ USARTx->CR3 |= CR3_NACK_Set;
+ }
+ else
+ {
+ /* Disable the NACK transmission by clearing the NACK bit in the CR3 register */
+ USARTx->CR3 &= CR3_NACK_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the USART’s Half Duplex communication.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART Communication.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_HalfDuplexCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the Half-Duplex mode by setting the HDSEL bit in the CR3 register */
+ USARTx->CR3 |= CR3_HDSEL_Set;
+ }
+ else
+ {
+ /* Disable the Half-Duplex mode by clearing the HDSEL bit in the CR3 register */
+ USARTx->CR3 &= CR3_HDSEL_Reset;
+ }
+}
+
+
+/**
+ * @brief Enables or disables the USART's 8x oversampling mode.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART one bit sampling method.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note
+ * This function has to be called before calling USART_Init()
+ * function in order to have correct baudrate Divider value.
+ * @retval None
+ */
+void USART_OverSampling8Cmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the 8x Oversampling mode by setting the OVER8 bit in the CR1 register */
+ USARTx->CR1 |= CR1_OVER8_Set;
+ }
+ else
+ {
+ /* Disable the 8x Oversampling mode by clearing the OVER8 bit in the CR1 register */
+ USARTx->CR1 &= CR1_OVER8_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the USART's one bit sampling method.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART one bit sampling method.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_OneBitMethodCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the one bit method by setting the ONEBITE bit in the CR3 register */
+ USARTx->CR3 |= CR3_ONEBITE_Set;
+ }
+ else
+ {
+ /* Disable tthe one bit method by clearing the ONEBITE bit in the CR3 register */
+ USARTx->CR3 &= CR3_ONEBITE_Reset;
+ }
+}
+
+/**
+ * @brief Configures the USART's IrDA interface.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_IrDAMode: specifies the IrDA mode.
+ * This parameter can be one of the following values:
+ * @arg USART_IrDAMode_LowPower
+ * @arg USART_IrDAMode_Normal
+ * @retval None
+ */
+void USART_IrDAConfig(USART_TypeDef* USARTx, uint16_t USART_IrDAMode)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_IRDA_MODE(USART_IrDAMode));
+
+ USARTx->CR3 &= CR3_IRLP_Mask;
+ USARTx->CR3 |= USART_IrDAMode;
+}
+
+/**
+ * @brief Enables or disables the USART's IrDA interface.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the IrDA mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_IrDACmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the IrDA mode by setting the IREN bit in the CR3 register */
+ USARTx->CR3 |= CR3_IREN_Set;
+ }
+ else
+ {
+ /* Disable the IrDA mode by clearing the IREN bit in the CR3 register */
+ USARTx->CR3 &= CR3_IREN_Reset;
+ }
+}
+
+/**
+ * @brief Checks whether the specified USART flag is set or not.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_FLAG: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg USART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5)
+ * @arg USART_FLAG_LBD: LIN Break detection flag
+ * @arg USART_FLAG_TXE: Transmit data register empty flag
+ * @arg USART_FLAG_TC: Transmission Complete flag
+ * @arg USART_FLAG_RXNE: Receive data register not empty flag
+ * @arg USART_FLAG_IDLE: Idle Line detection flag
+ * @arg USART_FLAG_ORE: OverRun Error flag
+ * @arg USART_FLAG_NE: Noise Error flag
+ * @arg USART_FLAG_FE: Framing Error flag
+ * @arg USART_FLAG_PE: Parity Error flag
+ * @retval The new state of USART_FLAG (SET or RESET).
+ */
+FlagStatus USART_GetFlagStatus(USART_TypeDef* USARTx, uint16_t USART_FLAG)
+{
+ FlagStatus bitstatus = RESET;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_FLAG(USART_FLAG));
+ /* The CTS flag is not available for UART4 and UART5 */
+ if (USART_FLAG == USART_FLAG_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ if ((USARTx->SR & USART_FLAG) != (uint16_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the USARTx's pending flags.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_FLAG: specifies the flag to clear.
+ * This parameter can be any combination of the following values:
+ * @arg USART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5).
+ * @arg USART_FLAG_LBD: LIN Break detection flag.
+ * @arg USART_FLAG_TC: Transmission Complete flag.
+ * @arg USART_FLAG_RXNE: Receive data register not empty flag.
+ *
+ * @note
+ * - PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
+ * error) and IDLE (Idle line detected) flags are cleared by software
+ * sequence: a read operation to USART_SR register (USART_GetFlagStatus())
+ * followed by a read operation to USART_DR register (USART_ReceiveData()).
+ * - RXNE flag can be also cleared by a read to the USART_DR register
+ * (USART_ReceiveData()).
+ * - TC flag can be also cleared by software sequence: a read operation to
+ * USART_SR register (USART_GetFlagStatus()) followed by a write operation
+ * to USART_DR register (USART_SendData()).
+ * - TXE flag is cleared only by a write to the USART_DR register
+ * (USART_SendData()).
+ * @retval None
+ */
+void USART_ClearFlag(USART_TypeDef* USARTx, uint16_t USART_FLAG)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_CLEAR_FLAG(USART_FLAG));
+ /* The CTS flag is not available for UART4 and UART5 */
+ if ((USART_FLAG & USART_FLAG_CTS) == USART_FLAG_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ USARTx->SR = (uint16_t)~USART_FLAG;
+}
+
+/**
+ * @brief Checks whether the specified USART interrupt has occurred or not.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_IT: specifies the USART interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg USART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg USART_IT_LBD: LIN Break detection interrupt
+ * @arg USART_IT_TXE: Tansmit Data Register empty interrupt
+ * @arg USART_IT_TC: Transmission complete interrupt
+ * @arg USART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg USART_IT_IDLE: Idle line detection interrupt
+ * @arg USART_IT_ORE: OverRun Error interrupt
+ * @arg USART_IT_NE: Noise Error interrupt
+ * @arg USART_IT_FE: Framing Error interrupt
+ * @arg USART_IT_PE: Parity Error interrupt
+ * @retval The new state of USART_IT (SET or RESET).
+ */
+ITStatus USART_GetITStatus(USART_TypeDef* USARTx, uint16_t USART_IT)
+{
+ uint32_t bitpos = 0x00, itmask = 0x00, usartreg = 0x00;
+ ITStatus bitstatus = RESET;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_GET_IT(USART_IT));
+ /* The CTS interrupt is not available for UART4 and UART5 */
+ if (USART_IT == USART_IT_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ /* Get the USART register index */
+ usartreg = (((uint8_t)USART_IT) >> 0x05);
+ /* Get the interrupt position */
+ itmask = USART_IT & IT_Mask;
+ itmask = (uint32_t)0x01 << itmask;
+
+ if (usartreg == 0x01) /* The IT is in CR1 register */
+ {
+ itmask &= USARTx->CR1;
+ }
+ else if (usartreg == 0x02) /* The IT is in CR2 register */
+ {
+ itmask &= USARTx->CR2;
+ }
+ else /* The IT is in CR3 register */
+ {
+ itmask &= USARTx->CR3;
+ }
+
+ bitpos = USART_IT >> 0x08;
+ bitpos = (uint32_t)0x01 << bitpos;
+ bitpos &= USARTx->SR;
+ if ((itmask != (uint16_t)RESET)&&(bitpos != (uint16_t)RESET))
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the USARTx's interrupt pending bits.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_IT: specifies the interrupt pending bit to clear.
+ * This parameter can be one of the following values:
+ * @arg USART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg USART_IT_LBD: LIN Break detection interrupt
+ * @arg USART_IT_TC: Transmission complete interrupt.
+ * @arg USART_IT_RXNE: Receive Data register not empty interrupt.
+ *
+ * @note
+ * - PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
+ * error) and IDLE (Idle line detected) pending bits are cleared by
+ * software sequence: a read operation to USART_SR register
+ * (USART_GetITStatus()) followed by a read operation to USART_DR register
+ * (USART_ReceiveData()).
+ * - RXNE pending bit can be also cleared by a read to the USART_DR register
+ * (USART_ReceiveData()).
+ * - TC pending bit can be also cleared by software sequence: a read
+ * operation to USART_SR register (USART_GetITStatus()) followed by a write
+ * operation to USART_DR register (USART_SendData()).
+ * - TXE pending bit is cleared only by a write to the USART_DR register
+ * (USART_SendData()).
+ * @retval None
+ */
+void USART_ClearITPendingBit(USART_TypeDef* USARTx, uint16_t USART_IT)
+{
+ uint16_t bitpos = 0x00, itmask = 0x00;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_CLEAR_IT(USART_IT));
+ /* The CTS interrupt is not available for UART4 and UART5 */
+ if (USART_IT == USART_IT_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ bitpos = USART_IT >> 0x08;
+ itmask = ((uint16_t)0x01 << (uint16_t)bitpos);
+ USARTx->SR = (uint16_t)~itmask;
+}
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/stm32f10x_conf.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/stm32f10x_conf.h
new file mode 100644
index 00000000..d606cd37
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/lib/STM32F10x_StdPeriph_Driver/stm32f10x_conf.h
@@ -0,0 +1,77 @@
+/**
+ ******************************************************************************
+ * @file Project/STM32F10x_StdPeriph_Template/stm32f10x_conf.h
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 08-April-2011
+ * @brief Library configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_CONF_H
+#define __STM32F10x_CONF_H
+
+/* Includes ------------------------------------------------------------------*/
+/* Uncomment/Comment the line below to enable/disable peripheral header file inclusion */
+/*#include "stm32f10x_adc.h"*/
+/*#include "stm32f10x_bkp.h"*/
+/*#include "stm32f10x_can.h"*/
+/*#include "stm32f10x_cec.h"*/
+/*#include "stm32f10x_crc.h"*/
+/*#include "stm32f10x_dac.h"*/
+/*#include "stm32f10x_dbgmcu.h"*/
+/*#include "stm32f10x_dma.h"*/
+/*#include "stm32f10x_exti.h"*/
+/*#include "stm32f10x_flash.h"*/
+/*#include "stm32f10x_fsmc.h"*/
+#include "stm32f10x_gpio.h" /* needed for configuring the SPI and UART pins */
+/*#include "stm32f10x_i2c.h"*/
+/*#include "stm32f10x_iwdg.h"*/
+/*#include "stm32f10x_pwr.h"*/
+#include "stm32f10x_rcc.h" /* needed for enabling the SPI and UART peripherals */
+/*#include "stm32f10x_rtc.h"*/
+/*#include "stm32f10x_sdio.h"*/
+#include "stm32f10x_spi.h" /* needed for low-level interfacing with SD-card */
+/*#include "stm32f10x_tim.h"*/
+#include "stm32f10x_usart.h" /* needed for UART logging during firmware updates from SD-card */
+/*#include "stm32f10x_wwdg.h"*/
+/*#include "misc.h"*/ /* High level functions for NVIC and SysTick (add-on to CMSIS functions) */
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/* Uncomment the line below to expanse the "assert_param" macro in the
+ Standard Peripheral Library drivers code */
+/* #define USE_FULL_ASSERT 1 */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function which reports
+ * the name of the source file and the source line number of the call
+ * that failed. If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0)
+#endif /* USE_FULL_ASSERT */
+
+#endif /* __STM32F10x_CONF_H */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/main.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/main.c
new file mode 100644
index 00000000..63fe7c09
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/main.c
@@ -0,0 +1,182 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Boot\main.c
+* \brief Bootloader application source file.
+* \ingroup Boot_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+
+/****************************************************************************************
+* Include files
+****************************************************************************************/
+#include "boot.h" /* bootloader generic header */
+#include "stm32f10x.h" /* microcontroller registers */
+
+
+/****************************************************************************************
+* Function prototypes
+****************************************************************************************/
+static void Init(void);
+
+
+/************************************************************************************//**
+** \brief This is the entry point for the bootloader application and is called
+** by the reset interrupt vector after the C-startup routines executed.
+** \return Program return code.
+**
+****************************************************************************************/
+int main(void)
+{
+ /* initialize the microcontroller */
+ Init();
+ /* initialize the bootloader */
+ BootInit();
+
+ /* start the infinite program loop */
+ while (1)
+ {
+ /* run the bootloader task */
+ BootTask();
+ }
+
+ /* program should never get here */
+ return 0;
+} /*** end of main ***/
+
+
+/************************************************************************************//**
+** \brief Initializes the microcontroller.
+** \return none.
+**
+****************************************************************************************/
+static void Init(void)
+{
+ volatile blt_int32u StartUpCounter = 0, HSEStatus = 0;
+ blt_int32u pll_multiplier;
+ GPIO_InitTypeDef GPIO_InitStruct;
+
+ /* reset the RCC clock configuration to the default reset state (for debug purpose) */
+ /* set HSION bit */
+ RCC->CR |= (blt_int32u)0x00000001;
+ /* reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */
+ RCC->CFGR &= (blt_int32u)0xF8FF0000;
+ /* reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (blt_int32u)0xFEF6FFFF;
+ /* reset HSEBYP bit */
+ RCC->CR &= (blt_int32u)0xFFFBFFFF;
+ /* reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */
+ RCC->CFGR &= (blt_int32u)0xFF80FFFF;
+ /* disable all interrupts and clear pending bits */
+ RCC->CIR = 0x009F0000;
+ /* enable HSE */
+ RCC->CR |= ((blt_int32u)RCC_CR_HSEON);
+ /* wait till HSE is ready and if Time out is reached exit */
+ do
+ {
+ HSEStatus = RCC->CR & RCC_CR_HSERDY;
+ StartUpCounter++;
+ }
+ while((HSEStatus == 0) && (StartUpCounter != 1500));
+ /* check if time out was reached */
+ if ((RCC->CR & RCC_CR_HSERDY) == RESET)
+ {
+ /* cannot continue when HSE is not ready */
+ ASSERT_RT(BLT_FALSE);
+ }
+ /* enable flash prefetch buffer */
+ FLASH->ACR |= FLASH_ACR_PRFTBE;
+ /* reset flash wait state configuration to default 0 wait states */
+ FLASH->ACR &= (blt_int32u)((blt_int32u)~FLASH_ACR_LATENCY);
+#if (BOOT_CPU_SYSTEM_SPEED_KHZ > 48000)
+ /* configure 2 flash wait states */
+ FLASH->ACR |= (blt_int32u)FLASH_ACR_LATENCY_2;
+#elif (BOOT_CPU_SYSTEM_SPEED_KHZ > 24000)
+ /* configure 1 flash wait states */
+ FLASH->ACR |= (blt_int32u)FLASH_ACR_LATENCY_1;
+#endif
+ /* HCLK = SYSCLK */
+ RCC->CFGR |= (blt_int32u)RCC_CFGR_HPRE_DIV1;
+ /* PCLK2 = HCLK/2 */
+ RCC->CFGR |= (blt_int32u)RCC_CFGR_PPRE2_DIV2;
+ /* PCLK1 = HCLK/2 */
+ RCC->CFGR |= (blt_int32u)RCC_CFGR_PPRE1_DIV2;
+ /* reset PLL configuration */
+ RCC->CFGR &= (blt_int32u)((blt_int32u)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | \
+ RCC_CFGR_PLLMULL));
+ /* assert that the pll_multiplier is between 2 and 16 */
+ ASSERT_CT((BOOT_CPU_SYSTEM_SPEED_KHZ/BOOT_CPU_XTAL_SPEED_KHZ) >= 2);
+ ASSERT_CT((BOOT_CPU_SYSTEM_SPEED_KHZ/BOOT_CPU_XTAL_SPEED_KHZ) <= 16);
+ /* calculate multiplier value */
+ pll_multiplier = BOOT_CPU_SYSTEM_SPEED_KHZ/BOOT_CPU_XTAL_SPEED_KHZ;
+ /* convert to register value */
+ pll_multiplier = (blt_int32u)((pll_multiplier - 2) << 18);
+ /* set the PLL multiplier and clock source */
+ RCC->CFGR |= (blt_int32u)(RCC_CFGR_PLLSRC_HSE | pll_multiplier);
+ /* enable PLL */
+ RCC->CR |= RCC_CR_PLLON;
+ /* wait till PLL is ready */
+ while((RCC->CR & RCC_CR_PLLRDY) == 0)
+ {
+ }
+ /* select PLL as system clock source */
+ RCC->CFGR &= (blt_int32u)((blt_int32u)~(RCC_CFGR_SW));
+ RCC->CFGR |= (blt_int32u)RCC_CFGR_SW_PLL;
+ /* wait till PLL is used as system clock source */
+ while ((RCC->CFGR & (blt_int32u)RCC_CFGR_SWS) != (blt_int32u)0x08)
+ {
+ }
+
+#if (BOOT_COM_UART_ENABLE > 0)
+ /* enable clock for USART2 peripheral */
+ RCC->APB1ENR |= (blt_int32u)0x00020000;
+ /* enable clocks for USART2 transmitter and receiver pins (GPIOA and AFIO) */
+ RCC->APB2ENR |= (blt_int32u)(0x00000004 | 0x00000001);
+ /* configure USART2 Tx (GPIOA2) as alternate function push-pull */
+ /* first reset the configuration */
+ GPIOA->CRL &= ~(blt_int32u)((blt_int32u)0xf << 8);
+ /* CNF2[1:0] = %10 and MODE2[1:0] = %11 */
+ GPIOA->CRL |= (blt_int32u)((blt_int32u)0xb << 8);
+ /* configure USART2 Rx (GPIOA3) as alternate function input floating */
+ /* first reset the configuration */
+ GPIOA->CRL &= ~(blt_int32u)((blt_int32u)0xf << 12);
+ /* CNF2[1:0] = %01 and MODE2[1:0] = %00 */
+ GPIOA->CRL |= (blt_int32u)((blt_int32u)0x4 << 12);
+#endif
+
+ /* configure the GPIO_LED pin */
+ RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
+ GPIO_InitStruct.GPIO_Pin = GPIO_Pin_5;
+ GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
+ GPIO_InitStruct.GPIO_Mode = GPIO_Mode_Out_PP;
+ GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* configure the pushbutton pin as input for backdoor entry */
+ RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
+ GPIO_InitStruct.GPIO_Pin = GPIO_Pin_13;
+ GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
+ GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IN_FLOATING;
+ GPIO_Init(GPIOC, &GPIO_InitStruct);
+} /*** end of Init ***/
+
+
+/*********************************** end of main.c *************************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/openblt_nucleo_stm32f103rb.elf.launch b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/openblt_nucleo_stm32f103rb.elf.launch
new file mode 100644
index 00000000..9beb0720
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/openblt_nucleo_stm32f103rb.elf.launch
@@ -0,0 +1,40 @@
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/startup_stm32f10x_md.s b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/startup_stm32f10x_md.s
new file mode 100644
index 00000000..e36f2e41
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Boot/startup_stm32f10x_md.s
@@ -0,0 +1,370 @@
+/**
+ ******************************************************************************
+ * @file startup_stm32f10x_md.s
+ * @author MCD Application Team
+ * @version V3.6.1
+ * @date 09-March-2012
+ * @brief STM32F10x Medium Density Devices vector table for Atollic toolchain.
+ * This module performs:
+ * - Set the initial SP
+ * - Set the initial PC == Reset_Handler,
+ * - Set the vector table entries with the exceptions ISR address
+ * - Configure the clock system
+ * - Branches to main in the C library (which eventually
+ * calls main()).
+ * After Reset the Cortex-M3 processor is in Thread mode,
+ * priority is Privileged, and the Stack is set to Main.
+ ******************************************************************************
+ * @attention
+ *
+ *
+
+ All
+STM32 devices definitions are commented by default. User has to select the
+appropriate device before starting else an error will be signaled on compile
+time.
+
Add new IRQs definitons inside the IRQn_Type enumeration for STM23 High-density Value line devices.
+
"bool" type removed.
+
+
STM32F10x CMSIS Cortex-M3 Device Peripheral Access Layer System Files:system_stm32f10x.h and system_stm32f10x.c
+
+
+
"system_stm32f10x.c" moved to to "STM32F10x_StdPeriph_Template" directory. This file is also moved to each example directory under "STM32F10x_StdPeriph_Examples".
+
+
SystemInit_ExtMemCtl() function: update to support High-density Value line devices.
+
Add "VECT_TAB_SRAM" inside "system_stm32f10x.c"
+to select if the user want to place the Vector Table in internal SRAM.
+An additional define is also to specify the Vector Table offset "VECT_TAB_OFFSET".
+
Update
+the stm32f10x.h file to support new Value line devices features: CEC
+peripheral, new General purpose timers TIM15, TIM16 and TIM17.
+
Peripherals Bits definitions updated to be in line with Value line devices available features.
+
+
HSE_Value,
+HSI_Value and HSEStartup_TimeOut changed to upper case: HSE_VALUE,
+HSI_VALUE and HSE_STARTUP_TIMEOUT. Old names are kept for legacy
+purposes.
+
+
+
STM32F10x CMSIS Cortex-M3 Device Peripheral Access Layer System Files:system_stm32f10x.h and system_stm32f10x.c
+
+
+
SystemFrequency variable name changed to SystemCoreClock
+
+
Default
+ SystemCoreClock is changed to 24MHz when Value line devices are selected and to 72MHz on other devices.
+
+
All while(1) loop were removed from all clock setting functions. User has to handle the HSE startup failure.
+
+
Additional function void SystemCoreClockUpdate (void) is provided.
+
Add new
+startup files for STM32 Low-density Value line devices:
+ startup_stm32f10x_ld_vl.s
+
Add new startup
+files for STM32 Medium-density Value line devices:
+ startup_stm32f10x_md_vl.s
+
SystemInit() function is called from startup file (startup_stm32f10x_xx.s) before to branch to application main.
+To reconfigure the default setting of SystemInit() function, refer to system_stm32f10x.c file
+
+
GNU startup file for Low density devices (startup_stm32f10x_ld.s) is updated to fix compilation errors.
+
+
+
+
+
+
+
+
License
+
The
+enclosed firmware and all the related documentation are not covered by
+a License Agreement, if you need such License you can contact your
+local STMicroelectronics office.
+
THE
+PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO
+SAVE TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR
+ANY DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY
+CLAIMS ARISING FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY
+CUSTOMERS OF THE CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH
+THEIR PRODUCTS.
+
+
+
+
For
+complete documentation on STM32(CORTEX M3) 32-Bit Microcontrollers
+visit www.st.com/STM32
+
+
+
+
+
+
+
+
+
+
+
+
+
\ No newline at end of file
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/stm32f10x.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/stm32f10x.h
new file mode 100644
index 00000000..af0c7c9a
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/CM3/DeviceSupport/ST/STM32F10x/stm32f10x.h
@@ -0,0 +1,8336 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x.h
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief CMSIS Cortex-M3 Device Peripheral Access Layer Header File.
+ * This file contains all the peripheral register's definitions, bits
+ * definitions and memory mapping for STM32F10x Connectivity line,
+ * High density, High density value line, Medium density,
+ * Medium density Value line, Low density, Low density Value line
+ * and XL-density devices.
+ *
+ * The file is the unique include file that the application programmer
+ * is using in the C source code, usually in main.c. This file contains:
+ * - Configuration section that allows to select:
+ * - The device used in the target application
+ * - To use or not the peripheral’s drivers in application code(i.e.
+ * code will be based on direct access to peripheral’s registers
+ * rather than drivers API), this option is controlled by
+ * "#define USE_STDPERIPH_DRIVER"
+ * - To change few application-specific parameters such as the HSE
+ * crystal frequency
+ * - Data structures and the address mapping for all peripherals
+ * - Peripheral's registers declarations and bits definition
+ * - Macros to access peripheral’s registers hardware
+ *
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ The Cortex-M3 incorporates the Instrumented Trace Macrocell (ITM) that provides together with
+ the Serial Viewer Output trace capabilities for the microcontroller system. The ITM has
+ 32 communication channels which are able to transmit 32 / 16 / 8 bit values; two ITM
+ communication channels are used by CMSIS to output the following information:
+
+
+
ITM Channel 0: used for printf-style output via the debug interface.
+
ITM Channel 31: is reserved for RTOS kernel awareness debugging.
+
+
+
Debug IN / OUT functions
+
CMSIS provides following debug functions:
+
+
ITM_SendChar (uses ITM channel 0)
+
ITM_ReceiveChar (uses global variable)
+
ITM_CheckChar (uses global variable)
+
+
+
ITM_SendChar
+
+ ITM_SendChar is used to transmit a character over ITM channel 0 from
+ the microcontroller system to the debug system.
+ Only a 8 bit value is transmitted.
+
+ ITM communication channel is only capable for OUT direction. For IN direction
+ a globel variable is used. A simple mechansim detects if a character is received.
+ The project to test need to be build with debug information.
+
+
+
+ The globale variable ITM_RxBuffer is used to transmit a 8 bit value from debug system
+ to microcontroller system. ITM_RxBuffer is 32 bit wide to enshure a proper handshake.
+
+
+extern volatile int ITM_RxBuffer; /* variable to receive characters */
+
+
+ A dedicated bit pattern is used to determin if ITM_RxBuffer is empty
+ or contains a valid value.
+
+
+#define ITM_RXBUFFER_EMPTY 0x5AA55AA5 /* value identifying ITM_RxBuffer is ready for next character */
+
+
+ ITM_ReceiveChar is used to receive a 8 bit value from the debug system. The function is nonblocking.
+ It returns the received character or '-1' if no character was available.
+
+
+static __INLINE int ITM_ReceiveChar (void) {
+ int ch = -1; /* no character available */
+
+ if (ITM_RxBuffer != ITM_RXBUFFER_EMPTY) {
+ ch = ITM_RxBuffer;
+ ITM_RxBuffer = ITM_RXBUFFER_EMPTY; /* ready for next character */
+ }
+
+ return (ch);
+}
+
+
+
ITM_CheckChar
+
+ ITM_CheckChar is used to check if a character is received.
+
+
+static __INLINE int ITM_CheckChar (void) {
+
+ if (ITM_RxBuffer == ITM_RXBUFFER_EMPTY) {
+ return (0); /* no character available */
+ } else {
+ return (1); /* character available */
+ }
+}
+
+
+
ITM Debug Support in uVision
+
+ uVision uses in a debug session the Debug (printf) Viewer window to
+ display the debug data.
+
+
Direction microcontroller system -> uVision:
+
+
+ Characters received via ITM communication channel 0 are written in a printf style
+ to Debug (printf) Viewer window.
+
+
+
+
Direction uVision -> microcontroller system:
+
+
Check if ITM_RxBuffer variable is available (only performed once).
+
Read character from Debug (printf) Viewer window.
+
If ITM_RxBuffer empty write character to ITM_RxBuffer.
+
+
+
Note
+
+
Current solution does not use a buffer machanism for trasmitting the characters.
+
+
+
+
RTX Kernel awareness in uVision
+
+ uVision / RTX are using a simple and efficient solution for RTX Kernel awareness.
+ No format overhead is necessary.
+ uVsion debugger decodes the RTX events via the 32 / 16 / 8 bit ITM write access
+ to ITM communication channel 31.
+
+
+
Following RTX events are traced:
+
+
Task Create / Delete event
+
+
32 bit access. Task start address is transmitted
+
16 bit access. Task ID and Create/Delete flag are transmitted
+ High byte holds Create/Delete flag, Low byte holds TASK ID.
+
+
+
+
Task switch event
+
+
8 bit access. Task ID of current task is transmitted
+
+
+
+
+
Note
+
+
Other RTOS information could be retrieved via memory read access in a polling mode manner.
+
+
+
+
\ No newline at end of file
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/CMSIS_changes.htm b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/CMSIS_changes.htm
new file mode 100644
index 00000000..162ffcc9
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/CMSIS_changes.htm
@@ -0,0 +1,320 @@
+
+
+
+CMSIS Changes
+
+
+
+
+
+
+
+
+
Changes to CMSIS version V1.20
+
+
+
+
1. Removed CMSIS Middelware packages
+
+ CMSIS Middleware is on hold from ARM side until a agreement between all CMSIS partners is found.
+
+
+
2. SystemFrequency renamed to SystemCoreClock
+
+ The variable name SystemCoreClock is more precise than SystemFrequency
+ because the variable holds the clock value at which the core is running.
+
+
+
3. Changed startup concept
+
+ The old startup concept (calling SystemInit_ExtMemCtl from startup file and calling SystemInit
+ from main) has the weakness that it does not work for controllers which need a already
+ configuerd clock system to configure the external memory controller.
+
+
+
Changed startup concept
+
+
+ SystemInit() is called from startup file before premain.
+
+
+ SystemInit() configures the clock system and also configures
+ an existing external memory controller.
+
+
+ SystemInit() must not use global variables.
+
+
+ SystemCoreClock is initialized with a correct predefined value.
+
+
+ Additional function void SystemCoreClockUpdate (void) is provided.
+ SystemCoreClockUpdate() updates the variable SystemCoreClock
+ and must be called whenever the core clock is changed.
+ SystemCoreClockUpdate() evaluates the clock register settings and calculates
+ the current core clock.
+
+
+
+
+
4. Advanced Debug Functions
+
+ ITM communication channel is only capable for OUT direction. To allow also communication for
+ IN direction a simple concept is provided.
+
+
+
+ Global variable volatile int ITM_RxBuffer used for IN data.
+
+
+ Function int ITM_CheckChar (void) checks if a new character is available.
+
+
+ Function int ITM_ReceiveChar (void) retrieves the new character.
+
+
+
+
+ For detailed explanation see file CMSIS debug support.htm.
+
+
+
+
5. Core Register Bit Definitions
+
+ Files core_cm3.h and core_cm0.h contain now bit definitions for Core Registers. The name for the
+ defines correspond with the Cortex-M Technical Reference Manual.
+
+ The Cortex Microcontroller Software Interface Standard (CMSIS) answers the challenges
+ that are faced when software components are deployed to physical microcontroller devices based on a
+ Cortex-M0 or Cortex-M3 processor. The CMSIS will be also expanded to future Cortex-M
+ processor cores (the term Cortex-M is used to indicate that). The CMSIS is defined in close co-operation
+ with various silicon and software vendors and provides a common approach to interface to peripherals,
+ real-time operating systems, and middleware components.
+
+
+
ARM provides as part of the CMSIS the following software layers that are
+available for various compiler implementations:
+
+
Core Peripheral Access Layer: contains name definitions,
+ address definitions and helper functions to
+ access core registers and peripherals. It defines also a device
+ independent interface for RTOS Kernels that includes debug channel
+ definitions.
+
+
+
These software layers are expanded by Silicon partners with:
+
+
Device Peripheral Access Layer: provides definitions
+ for all device peripherals
+
Access Functions for Peripherals (optional): provides
+ additional helper functions for peripherals
+
+
+
CMSIS defines for a Cortex-M Microcontroller System:
+
+
A common way to access peripheral registers
+ and a common way to define exception vectors.
+
The register names of the Core
+ Peripherals andthe names of the Core
+ Exception Vectors.
+
An device independent interface for RTOS Kernels including a debug
+ channel.
+
+
+
+ By using CMSIS compliant software components, the user can easier re-use template code.
+ CMSIS is intended to enable the combination of software components from multiple middleware vendors.
+
+
+
Coding Rules and Conventions
+
+
+ The following section describes the coding rules and conventions used in the CMSIS
+ implementation. It contains also information about data types and version number information.
+
+
+
Essentials
+
+
The CMSIS C code conforms to MISRA 2004 rules. In case of MISRA violations,
+ there are disable and enable sequences for PC-LINT inserted.
+
ANSI standard data types defined in the ANSI C header file
+ <stdint.h> are used.
+
#define constants that include expressions must be enclosed by
+ parenthesis.
+
Variables and parameters have a complete data type.
+
All functions in the Core Peripheral Access Layer are
+ re-entrant.
+
The Core Peripheral Access Layer has no blocking code
+ (which means that wait/query loops are done at other software layers).
+
For each exception/interrupt there is definition for:
+
+
an exception/interrupt handler with the postfix _Handler
+ (for exceptions) or _IRQHandler (for interrupts).
+
a default exception/interrupt handler (weak definition) that contains an endless loop.
+
a #define of the interrupt number with the postfix _IRQn.
+
+
+
+
Recommendations
+
+
The CMSIS recommends the following conventions for identifiers.
+
+
CAPITAL names to identify Core Registers, Peripheral Registers, and CPU Instructions.
+
CamelCase names to identify peripherals access functions and interrupts.
+
PERIPHERAL_ prefix to identify functions that belong to specify peripherals.
+
Doxygen comments for all functions are included as described under Function Comments below.
+
+
+Comments
+
+
+
Comments use the ANSI C90 style (/* comment */) or C++ style
+ (// comment). It is assumed that the programming tools support today
+ consistently the C++ comment style.
+
Function Comments provide for each function the following information:
+
+
one-line brief function overview.
+
detailed parameter explanation.
+
detailed information about return values.
+
detailed description of the actual function.
+
+
Doxygen Example:
+
+/**
+ * @brief Enable Interrupt in NVIC Interrupt Controller
+ * @param IRQn interrupt number that specifies the interrupt
+ * @return none.
+ * Enable the specified interrupt in the NVIC Interrupt Controller.
+ * Other settings of the interrupt such as priority are not affected.
+ */
+
+
+
+
Data Types and IO Type Qualifiers
+
+
+ The Cortex-M HAL uses the standard types from the standard ANSI C header file
+ <stdint.h>. IO Type Qualifiers are used to specify the access
+ to peripheral variables. IO Type Qualifiers are indented to be used for automatic generation of
+ debug information of peripheral registers.
+
+
+
+
+
+
IO Type Qualifier
+
#define
+
Description
+
+
+
__I
+
volatile const
+
Read access only
+
+
+
__O
+
volatile
+
Write access only
+
+
+
__IO
+
volatile
+
Read and write access
+
+
+
+
+
CMSIS Version Number
+
+ File core_cm3.h contains the version number of the CMSIS with the following define:
+
+
+
+#define __CM3_CMSIS_VERSION_MAIN (0x01) /* [31:16] main version */
+#define __CM3_CMSIS_VERSION_SUB (0x30) /* [15:0] sub version */
+#define __CM3_CMSIS_VERSION ((__CM3_CMSIS_VERSION_MAIN << 16) | __CM3_CMSIS_VERSION_SUB)
+
+
+ File core_cm0.h contains the version number of the CMSIS with the following define:
+
+
+
+#define __CM0_CMSIS_VERSION_MAIN (0x01) /* [31:16] main version */
+#define __CM0_CMSIS_VERSION_SUB (0x30) /* [15:0] sub version */
+#define __CM0_CMSIS_VERSION ((__CM0_CMSIS_VERSION_MAIN << 16) | __CM0_CMSIS_VERSION_SUB)
+
+
+
CMSIS Cortex Core
+
+ File core_cm3.h contains the type of the CMSIS Cortex-M with the following define:
+
+
+
+#define __CORTEX_M (0x03)
+
+
+ File core_cm0.h contains the type of the CMSIS Cortex-M with the following define:
+
+
+
+#define __CORTEX_M (0x00)
+
+
+
CMSIS Files
+
+ This section describes the Files provided in context with the CMSIS to access the Cortex-M
+ hardware and peripherals.
+
+
+
+
+
+
File
+
Provider
+
Description
+
+
+
device.h
+
Device specific (provided by silicon partner)
+
Defines the peripherals for the actual device. The file may use
+ several other include files to define the peripherals of the actual device.
+
+
+
core_cm0.h
+
ARM (for RealView ARMCC, IAR, and GNU GCC)
+
Defines the core peripherals for the Cortex-M0 CPU and core peripherals.
+
+
+
core_cm3.h
+
ARM (for RealView ARMCC, IAR, and GNU GCC)
+
Defines the core peripherals for the Cortex-M3 CPU and core peripherals.
+
+
+
core_cm0.c
+
ARM (for RealView ARMCC, IAR, and GNU GCC)
+
Provides helper functions that access core registers.
+
+
+
core_cm3.c
+
ARM (for RealView ARMCC, IAR, and GNU GCC)
+
Provides helper functions that access core registers.
+
+
+
startup_device
+
ARM (adapted by compiler partner / silicon partner)
+
Provides the Cortex-M startup code and the complete (device specific) Interrupt Vector Table
+
+
+
system_device
+
ARM (adapted by silicon partner)
+
Provides a device specific configuration file for the device. It configures the device initializes
+ typically the oscillator (PLL) that is part of the microcontroller device
+
+
+
+
+
device.h
+
+
+ The file device.h is provided by the silicon vendor and is the
+ central include file that the application programmer is using in
+ the C source code. This file contains:
+
+
+
+
Interrupt Number Definition: provides interrupt numbers
+ (IRQn) for all core and device specific exceptions and interrupts.
+
+
+
Configuration for core_cm0.h / core_cm3.h: reflects the
+ actual configuration of the Cortex-M processor that is part of the actual
+ device. As such the file core_cm0.h / core_cm3.h is included that
+ implements access to processor registers and core peripherals.
+
+
+
Device Peripheral Access Layer: provides definitions
+ for all device peripherals. It contains all data structures and the address
+ mapping for the device specific peripherals.
+
+
Access Functions for Peripherals (optional): provides
+ additional helper functions for peripherals that are useful for programming
+ of these peripherals. Access Functions may be provided as inline functions
+ or can be extern references to a device specific library provided by the
+ silicon vendor.
+
+
+
+
Interrupt Number Definition
+
+
To access the device specific interrupts the device.h file defines IRQn
+numbers for the complete device using a enum typedef as shown below:
+ The Cortex-M core configuration options which are defined for each device implementation. Some
+ configuration options are reflected in the CMSIS layer using the #define settings described below.
+
+
+ To access core peripherals file device.h includes file core_cm0.h / core_cm3.h.
+ Several features in core_cm0.h / core_cm3.h are configured by the following defines that must be
+ defined before #include <core_cm0.h> / #include <core_cm3.h>
+ preprocessor command.
+
+
+
+
+
+
#define
+
File
+
Value
+
Description
+
+
+
__NVIC_PRIO_BITS
+
core_cm0.h
+
(2)
+
Number of priority bits implemented in the NVIC (device specific)
+
+
+
__NVIC_PRIO_BITS
+
core_cm3.h
+
(2 ... 8)
+
Number of priority bits implemented in the NVIC (device specific)
+
+
+
__MPU_PRESENT
+
core_cm0.h, core_cm3.h
+
(0, 1)
+
Defines if an MPU is present or not
+
+
+
__Vendor_SysTickConfig
+
core_cm0.h, core_cm3.h
+
(1)
+
When this define is setup to 1, the SysTickConfig function
+ in core_cm3.h is excluded. In this case the device.h
+ file must contain a vendor specific implementation of this function.
+
+
+
+
+
+
Device Peripheral Access Layer
+
+ Each peripheral uses a prefix which consists of <device abbreviation>_
+ and <peripheral name>_ to identify peripheral registers that access this
+ specific peripheral. The intention of this is to avoid name collisions caused
+ due to short names. If more than one peripheral of the same type exists,
+ identifiers have a postfix (digit or letter). For example:
+
+
+
<device abbreviation>_UART_Type: defines the generic register layout for all UART channels in a device.
+
<device abbreviation>_UART1: is a pointer to a register structure that refers to a specific UART.
+ For example UART1->DR is the data register of UART1.
+
+ To access the peripheral registers and related function in a device the files device.h
+ and core_cm0.h / core_cm3.h defines as a minimum:
+
+
+
The Register Layout Typedef for each peripheral that defines all register names.
+ Names that start with RESERVE are used to introduce space into the structure to adjust the addresses of
+ the peripheral registers. For example:
+
+typedef struct {
+ __IO uint32_t CTRL; /* SysTick Control and Status Register */
+ __IO uint32_t LOAD; /* SysTick Reload Value Register */
+ __IO uint32_t VAL; /* SysTick Current Value Register */
+ __I uint32_t CALIB; /* SysTick Calibration Register */
+ } SysTick_Type;
+
+
+
+ Base Address for each peripheral (in case of multiple peripherals
+ that use the same register layout typedef multiple base addresses are defined). For example:
+
+#define SysTick_BASE (SCS_BASE + 0x0010) /* SysTick Base Address */
+
+
+
+ Access Definition for each peripheral (in case of multiple peripherals that use
+ the same register layout typedef multiple access definitions exist, i.e. LPC_UART0,
+ LPC_UART2). For Example:
+
+ These definitions allow to access the peripheral registers from user code with simple assignments like:
+
+
SysTick->CTRL = 0;
+
+
Optional Features
+
In addition the device.h file may define:
+
+
+ #define constants that simplify access to the peripheral registers.
+ These constant define bit-positions or other specific patterns are that required for the
+ programming of the peripheral registers. The identifiers used start with
+ <device abbreviation>_ and <peripheral name>_.
+ It is recommended to use CAPITAL letters for such #define constants.
+
+
+ Functions that perform more complex functions with the peripheral (i.e. status query before
+ a sending register is accessed). Again these function start with
+ <device abbreviation>_ and <peripheral name>_.
+
+
+
+
core_cm0.h and core_cm0.c
+
+ File core_cm0.h describes the data structures for the Cortex-M0 core peripherals and does
+ the address mapping of this structures. It also provides basic access to the Cortex-M0 core registers
+ and core peripherals with efficient functions (defined as static inline).
+
+
+ File core_cm0.c defines several helper functions that access processor registers.
+
+ File core_cm3.h describes the data structures for the Cortex-M3 core peripherals and does
+ the address mapping of this structures. It also provides basic access to the Cortex-M3 core registers
+ and core peripherals with efficient functions (defined as static inline).
+
+
+ File core_cm3.c defines several helper functions that access processor registers.
+
+ A template file for startup_device is provided by ARM for each supported
+ compiler. It is adapted by the silicon vendor to include interrupt vectors for all device specific
+ interrupt handlers. Each interrupt handler is defined as weak function
+ to an dummy handler. Therefore the interrupt handler can be directly used in application software
+ without any requirements to adapt the startup_device file.
+
+
+ The following exception names are fixed and define the start of the vector table for a Cortex-M0:
+
+ The user application may simply define an interrupt handler function by using the handler name
+ as shown below.
+
+
+void WWDG_IRQHandler(void)
+{
+ :
+ :
+}
+
+
+
system_device.c
+
+ A template file for system_device.c is provided by ARM but adapted by
+ the silicon vendor to match their actual device. As a minimum requirement
+ this file must provide a device specific system configuration function and a global variable
+ that contains the system frequency. It configures the device and initializes typically the
+ oscillator (PLL) that is part of the microcontroller device.
+
+
+ The file system_device.c must provide
+ as a minimum requirement the SystemInit function as shown below.
+
+
+
+
+
+
Function Definition
+
Description
+
+
+
void SystemInit (void)
+
Setup the microcontroller system. Typically this function configures the
+ oscillator (PLL) that is part of the microcontroller device. For systems
+ with variable clock speed it also updates the variable SystemCoreClock.
+ SystemInit is called from startup_device file.
+
+
+
void SystemCoreClockUpdate (void)
+
Updates the variable SystemCoreClock and must be called whenever the
+ core clock is changed during program execution. SystemCoreClockUpdate()
+ evaluates the clock register settings and calculates the current core clock.
+
+
+
+
+
+
+ Also part of the file system_device.c
+ is the variable SystemCoreClock which contains the current CPU clock speed shown below.
+
+
+
+
+
+
Variable Definition
+
Description
+
+
+
uint32_t SystemCoreClock
+
Contains the system core clock (which is the system clock frequency supplied
+ to the SysTick timer and the processor core clock). This variable can be
+ used by the user application to setup the SysTick timer or configure other
+ parameters. It may also be used by debugger to query the frequency of the
+ debug timer or configure the trace clock speed.
+ SystemCoreClock is initialized with a correct predefined value.
+ The compiler must be configured to avoid the removal of this variable in
+ case that the application program is not using it. It is important for
+ debug systems that the variable is physically present in memory so that
+ it can be examined to configure the debugger.
+
+
+
+
+
Note
+
+
The above definitions are the minimum requirements for the file
+ system_device.c. This
+ file may export more functions or variables that provide a more flexible
+ configuration of the microcontroller system.
+
+
+
+
+
Core Peripheral Access Layer
+
+
Cortex-M Core Register Access
+
+ The following functions are defined in core_cm0.h / core_cm3.h
+ and provide access to Cortex-M core registers.
+
+
+
+
+
+
Function Definition
+
Core
+
Core Register
+
Description
+
+
+
void __enable_irq (void)
+
M0, M3
+
PRIMASK = 0
+
Global Interrupt enable (using the instruction CPSIE
+ i)
+
+
+
void __disable_irq (void)
+
M0, M3
+
PRIMASK = 1
+
Global Interrupt disable (using the instruction
+ CPSID i)
+
+
+
void __set_PRIMASK (uint32_t value)
+
M0, M3
+
PRIMASK = value
+
Assign value to Priority Mask Register (using the instruction
+ MSR)
+
+
+
uint32_t __get_PRIMASK (void)
+
M0, M3
+
return PRIMASK
+
Return Priority Mask Register (using the instruction
+ MRS)
+
+
+
void __enable_fault_irq (void)
+
M3
+
FAULTMASK = 0
+
Global Fault exception and Interrupt enable (using the
+ instruction CPSIE
+ f)
+
+
+
void __disable_fault_irq (void)
+
M3
+
FAULTMASK = 1
+
Global Fault exception and Interrupt disable (using the
+ instruction CPSID f)
+
+
+
void __set_FAULTMASK (uint32_t value)
+
M3
+
FAULTMASK = value
+
Assign value to Fault Mask Register (using the instruction
+ MSR)
+
+
+
uint32_t __get_FAULTMASK (void)
+
M3
+
return FAULTMASK
+
Return Fault Mask Register (using the instruction MRS)
+
+
+
void __set_BASEPRI (uint32_t value)
+
M3
+
BASEPRI = value
+
Set Base Priority (using the instruction MSR)
+
+
+
uiuint32_t __get_BASEPRI (void)
+
M3
+
return BASEPRI
+
Return Base Priority (using the instruction MRS)
+
+
+
void __set_CONTROL (uint32_t value)
+
M0, M3
+
CONTROL = value
+
Set CONTROL register value (using the instruction MSR)
+
+
+
uint32_t __get_CONTROL (void)
+
M0, M3
+
return CONTROL
+
Return Control Register Value (using the instruction
+ MRS)
+
+
+
void __set_PSP (uint32_t TopOfProcStack)
+
M0, M3
+
PSP = TopOfProcStack
+
Set Process Stack Pointer value (using the instruction
+ MSR)
+
+
+
uint32_t __get_PSP (void)
+
M0, M3
+
return PSP
+
Return Process Stack Pointer (using the instruction MRS)
+
+
+
void __set_MSP (uint32_t TopOfMainStack)
+
M0, M3
+
MSP = TopOfMainStack
+
Set Main Stack Pointer (using the instruction MSR)
+
+
+
uint32_t __get_MSP (void)
+
M0, M3
+
return MSP
+
Return Main Stack Pointer (using the instruction MRS)
+
+
+
+
+
Cortex-M Instruction Access
+
+ The following functions are defined in core_cm0.h / core_cm3.hand
+ generate specific Cortex-M instructions. The functions are implemented in the file
+ core_cm0.c / core_cm3.c.
+
+
+
+
+
+
Name
+
Core
+
Generated CPU Instruction
+
Description
+
+
+
void __NOP (void)
+
M0, M3
+
NOP
+
No Operation
+
+
+
void __WFI (void)
+
M0, M3
+
WFI
+
Wait for Interrupt
+
+
+
void __WFE (void)
+
M0, M3
+
WFE
+
Wait for Event
+
+
+
void __SEV (void)
+
M0, M3
+
SEV
+
Set Event
+
+
+
void __ISB (void)
+
M0, M3
+
ISB
+
Instruction Synchronization Barrier
+
+
+
void __DSB (void)
+
M0, M3
+
DSB
+
Data Synchronization Barrier
+
+
+
void __DMB (void)
+
M0, M3
+
DMB
+
Data Memory Barrier
+
+
+
uint32_t __REV (uint32_t value)
+
M0, M3
+
REV
+
Reverse byte order in integer value.
+
+
+
uint32_t __REV16 (uint16_t value)
+
M0, M3
+
REV16
+
Reverse byte order in unsigned short value.
+
+
+
sint32_t __REVSH (sint16_t value)
+
M0, M3
+
REVSH
+
Reverse byte order in signed short value with sign extension to integer.
Remove the exclusive lock created by __LDREXB, __LDREXH, or __LDREXW
+
+
+
+
+
+
NVIC Access Functions
+
+ The CMSIS provides access to the NVIC via the register interface structure and several helper
+ functions that simplify the setup of the NVIC. The CMSIS HAL uses IRQ numbers (IRQn) to
+ identify the interrupts. The first device interrupt has the IRQn value 0. Therefore negative
+ IRQn values are used for processor core exceptions.
+
+
+ For the IRQn values of core exceptions the file device.h provides
+ the following enum names.
+
+
+
+
+
+
Core Exception enum Value
+
Core
+
IRQn
+
Description
+
+
+
NonMaskableInt_IRQn
+
M0, M3
+
-14
+
Cortex-M Non Maskable Interrupt
+
+
+
HardFault_IRQn
+
M0, M3
+
-13
+
Cortex-M Hard Fault Interrupt
+
+
+
MemoryManagement_IRQn
+
M3
+
-12
+
Cortex-M Memory Management Interrupt
+
+
+
BusFault_IRQn
+
M3
+
-11
+
Cortex-M Bus Fault Interrupt
+
+
+
UsageFault_IRQn
+
M3
+
-10
+
Cortex-M Usage Fault Interrupt
+
+
+
SVCall_IRQn
+
M0, M3
+
-5
+
Cortex-M SV Call Interrupt
+
+
+
DebugMonitor_IRQn
+
M3
+
-4
+
Cortex-M Debug Monitor Interrupt
+
+
+
PendSV_IRQn
+
M0, M3
+
-2
+
Cortex-M Pend SV Interrupt
+
+
+
SysTick_IRQn
+
M0, M3
+
-1
+
Cortex-M System Tick Interrupt
+
+
+
+
+
The following functions simplify the setup of the NVIC.
+The functions are defined as static inline.
IRQ Number, Priority, pointer to Priority Group, pointer to Preemptive Priority, pointer to Sub Priority
+
Deccode given priority to group, preemptive and sub priority
+
+
+
void NVIC_SystemReset (void)
+
M0, M3
+
(void)
+
Resets the System
+
+
+
+
Note
+
+
The processor exceptions have negative enum values. Device specific interrupts
+ have positive enum values and start with 0. The values are defined in
+ device.h file.
+
+
+
The values for PreemptPriority and SubPriority
+ used in functions NVIC_EncodePriority and NVIC_DecodePriority
+ depend on the available __NVIC_PRIO_BITS implemented in the NVIC.
+
+
+
+
+
+
SysTick Configuration Function
+
+
The following function is used to configure the SysTick timer and start the
+SysTick interrupt.
+
+
+
+
+
Name
+
Parameter
+
Description
+
+
+
uint32_t SysTickConfig
+ (uint32_t ticks)
+
ticks is SysTick counter reload value
+
Setup the SysTick timer and enable the SysTick interrupt. After this
+ call the SysTick timer creates interrupts with the specified time
+ interval.
+
+ Return: 0 when successful, 1 on failure.
+
+
+
+
+
+
+
Cortex-M3 ITM Debug Access
+
+
The Cortex-M3 incorporates the Instrumented Trace Macrocell (ITM) that
+provides together with the Serial Viewer Output trace capabilities for the
+microcontroller system. The ITM has 32 communication channels; two ITM
+communication channels are used by CMSIS to output the following information:
+
+
ITM Channel 0: implements the ITM_SendChar function
+ which can be used for printf-style output via the debug interface.
+
ITM Channel 31: is reserved for the RTOS kernel and can be used for
+ kernel awareness debugging.
+
+
Note
+
+
The ITM channel 31 is selected for the RTOS kernel since some kernels
+ may use the Privileged level for program execution. ITM
+ channels have 4 groups with 8 channels each, whereby each group can be
+ configured for access rights in the Unprivileged level. The ITM channel 0
+ may be therefore enabled for the user task whereas ITM channel 31 may be
+ accessible only in Privileged level from the RTOS kernel itself.
+
+
+
+
The prototype of the ITM_SendChar routine is shown in the
+table below.
+
+
+
+
+
Name
+
Parameter
+
Description
+
+
+
void uint32_t ITM_SendChar(uint32_t chr)
+
character to output
+
The function outputs a character via the ITM channel 0. The
+ function returns when no debugger is connected that has booked the
+ output. It is blocking when a debugger is connected, but the
+ previous character send is not transmitted.
+ Return: the input character 'chr'.
+
+
+
+
+
+ Example for the usage of the ITM Channel 31 for RTOS Kernels:
+
+
+ // check if debugger connected and ITM channel enabled for tracing
+ if ((CoreDebug->DEMCR & CoreDebug_DEMCR_TRCENA) &&
+ (ITM->TCR & ITM_TCR_ITMENA) &&
+ (ITM->TER & (1UL << 31))) {
+ // transmit trace data
+ while (ITM->PORT31_U32 == 0);
+ ITM->PORT[31].u8 = task_id; // id of next task
+ while (ITM->PORT[31].u32 == 0);
+ ITM->PORT[31].u32 = task_status; // status information
+ }
+
+
+
Cortex-M3 additional Debug Access
+
+
CMSIS provides additional debug functions to enlarge the Cortex-M3 Debug Access.
+Data can be transmitted via a certain global buffer variable towards the target system.
+
+
The buffer variable and the prototypes of the additional functions are shown in the
+table below.
+
+
+
+
+
Name
+
Parameter
+
Description
+
+
+
extern volatile int ITM_RxBuffer
+
+
Buffer to transmit data towards debug system.
+ Value 0x5AA55AA5 indicates that buffer is empty.
+
+
+
int ITM_ReceiveChar (void)
+
none
+
The nonblocking functions returns the character stored in
+ ITM_RxBuffer.
+ Return: -1 indicates that no character was received.
+
+
+
int ITM_CheckChar (void)
+
none
+
The function checks if a character is available in ITM_RxBuffer.
+ Return: 1 indicates that a character is available, 0 indicates that
+ no character is available.
+
+
+
+
+
+
CMSIS Example
+
+ The following section shows a typical example for using the CMSIS layer in user applications.
+ The example is based on a STM32F10x Device.
+
+
+#include "stm32f10x.h"
+
+volatile uint32_t msTicks; /* timeTicks counter */
+
+void SysTick_Handler(void) {
+ msTicks++; /* increment timeTicks counter */
+}
+
+__INLINE static void Delay (uint32_t dlyTicks) {
+ uint32_t curTicks = msTicks;
+
+ while ((msTicks - curTicks) < dlyTicks);
+}
+
+__INLINE static void LED_Config(void) {
+ ; /* Configure the LEDs */
+}
+
+__INLINE static void LED_On (uint32_t led) {
+ ; /* Turn On LED */
+}
+
+__INLINE static void LED_Off (uint32_t led) {
+ ; /* Turn Off LED */
+}
+
+int main (void) {
+ if (SysTick_Config (SystemCoreClock / 1000)) { /* Setup SysTick for 1 msec interrupts */
+ ; /* Handle Error */
+ while (1);
+ }
+
+ LED_Config(); /* configure the LEDs */
+
+ while(1) {
+ LED_On (0x100); /* Turn on the LED */
+ Delay (100); /* delay 100 Msec */
+ LED_Off (0x100); /* Turn off the LED */
+ Delay (100); /* delay 100 Msec */
+ }
+}
+
+
+
\ No newline at end of file
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/License.doc b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/License.doc
new file mode 100644
index 00000000..b6b8acec
Binary files /dev/null and b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/CMSIS/License.doc differ
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/Release_Notes.html b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/Release_Notes.html
new file mode 100644
index 00000000..633e42e3
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/Release_Notes.html
@@ -0,0 +1,342 @@
+
+
+
+
+
+
+
+
+
+
+
+
+Release Notes for STM32F10x Standard Peripherals Library Drivers
+
+
+
+
+
+
STM32F10x Standard
+Peripherals Library Drivers update History
+
V3.5.0 / 11-March-2011
+
Main
+Changes
+
+
+
stm32f10x_can.h/.c files:
+
+
Add 5 new functions
+
+
3
+new functions controlling the counter errors: CAN_GetLastErrorCode(),
+CAN_GetReceiveErrorCounter() and CAN_GetLSBTransmitErrorCounter().
+
+
+
1 new function to select the CAN operating mode: CAN_OperatingModeRequest().
+
+
+
1 new function to support CAN TT mode: CAN_TTComModeCmd().
+
+
+
CAN_TransmitStatus() function updated to support all CAN transmit intermediate states
+
+
+
stm32f10x_i2c.h/.c files:
+
+
Add 1 new function:
+
+
I2C_NACKPositionConfig():
+This function configures the same bit (POS) as I2C_PECPositionConfig()
+but is intended to be used in I2C mode while I2C_PECPositionConfig() is
+intended to used in SMBUS mode.
+
+
+
stm32f10x_tim.h/.c files:
+
+
Change the TIM_DMABurstLength_xBytes definitions to TIM_DMABurstLength_xTansfers
+
+
+
+
+
+
+
3.4.0
+- 10/15/2010
+
+
+
General
+
+
+
+
Add support for STM32F10x High-density value line devices.
+
+
+
+
STM32F10x_StdPeriph_Driver
+
+
+
+
+
+
stm32f10x_bkp.h/.c
+
+
Delete BKP registers definition from stm32f10x_bkp.c and use defines within stm32f10x.h file.
+
+
stm32f10x_can.h/.c
+
+
Delete CAN registers definition from stm32f10x_can.c and use defines within stm32f10x.h file.
+
+
Update the wording of some defines and Asserts macro.
+
+
CAN_GetFlagStatus()
+and CAN_ClearFlag() functions: updated to support new flags (were not
+supported in previous version). These flags are: CAN_FLAG_RQCP0,
+CAN_FLAG_RQCP1, CAN_FLAG_RQCP2, CAN_FLAG_FMP1, CAN_FLAG_FF1,
+CAN_FLAG_FOV1, CAN_FLAG_FMP0, CAN_FLAG_FF0, CAN_FLAG_FOV0,
+CAN_FLAG_WKU, CAN_FLAG_SLAK and CAN_FLAG_LEC.
+
+
CAN_GetITStatus()
+function: add a check of the interrupt enable bit before getting the
+status of corresponding interrupt pending bit.
+
+
CAN_ClearITPendingBit() function: correct the procedure to clear the interrupt pending bit.
+
+
+
stm32f10x_crc.h/.c
+
+
Delete CRC registers definition from stm32f10x_crc.c and use defines within stm32f10x.h file.
+
+
stm32f10x_dac.h/.c
+
+
Delete DAC registers definition from stm32f10x_dac.c and use defines within stm32f10x.h file.
+
+
stm32f10x_dbgmcu.h/.c
+
+
Delete DBGMCU registers definition from stm32f10x_dbgmcu.c and use defines within stm32f10x.h file.
+
+
stm32f10x_dma.h/.c
+
+
Delete DMA registers definition from stm32f10x_dma.c and use defines within stm32f10x.h file.
+
Add new function "void DMA_SetCurrDataCounter(DMA_Channel_TypeDef* DMAy_Channelx, uint16_t DataNumber);"
+
+
+
stm32f10x_flash.h/.c
+
+
FLASH functions (Erase and Program) updated to always clear the "PG", "MER" and "PER" bits even in case of TimeOut Error.
+
+
stm32f10x_fsmc.h/.c
+
+
Add new member "FSMC_AsynchronousWait" in "FSMC_NORSRAMInitTypeDef" structure.
+
+
stm32f10x_gpio.h/.c
+
+
GPIO_PinRemapConfig() function: add new values for GPIO_Remap parameter, to support new remap for TIM6, TIM7 and DAC DMA requests, TIM12 and DAC Triggers / DMA2_Channel5 Interrupt mapping.
+
+
stm32f10x_pwr.h/.c
+
+
Delete PWR registers definition from stm32f10x_pwr.c and use defines within stm32f10x.h and core_cm3.h files.
+
+
stm32f10x_rtc.h/.c
+
+
Delete RTC registers definition from stm32f10x_rtc.c and use defines within stm32f10x.h file.
+
+
stm32f10x_spi.h/.c
+
+
Add new definition for I2S Audio Clock frequencies "I2S_AudioFreq_192k".
+
+
stm32f10x_tim.h/.c
+
Add new definition for TIM Input Capture Polarity "TIM_ICPolarity_BothEdge".
+
+
+
+
3.3.0
+- 04/16/2010
+
+
General
+
Add support for STM32F10x XL-density devices.
I2C driver: events description and management enhancement.
+
STM32F10x_StdPeriph_Driver
+
stm32f10x_dbgmcu.h/.c
DBGMCU_Config() function: add new values DBGMCU_TIMx_STOP (x: 9..14) for DBGMCU_Periph parameter.
stm32f10x_flash.h/.c:
+updated to support Bank2 of XL-density devices (up to 1MByte of Flash
+memory). For more details, refer to the description provided within
+stm32f10x_flash.c file.
stm32f10x_gpio.h/.c
GPIO_PinRemapConfig() function: add new values for GPIO_Remap parameter, to support new remap for FSMC_NADV pin and TIM9..11,13,14.
stm32f10x_i2c.h/.c: I2C events description and management enhancement.
I2C_CheckEvent()
+function: updated to check whether the last event contains the
+I2C_EVENT (instead of check whether the last event is equal to
+I2C_EVENT)
Add
+detailed description of I2C events and how to manage them using the
+functions provided by this driver. For more information, refer to
+stm32f10x_i2c.h and stm32f10x_i2c.c files.
stm32f10x_rcc.h/.c: updated to support TIM9..TIM14 APB clock and reset configuration
stm32f10x_tim.h/.c: updated to support new Timers TIM9..TIM14.
Add support
+for STM32 Low-density Value line (STM32F100x4/6) and
+Medium-density Value line (STM32F100x8/B) devices.
+
Almost
+peripherals drivers were updated to support Value
+line devices features
+
Drivers limitations fix and enhancements.
+
+
+
+
STM32F10x_StdPeriph_Driver
+
+
+
Add new
+firmware driver for CEC peripheral: stm32f10x_cec.h and stm32f10x_cec.c
+
Timers drivers stm32f10x_tim.h/.c: add support for new General Purpose Timers: TIM15, TIM16 and TIM17.
+
RCC driver: add support for new Value peripherals: HDMI-CEC, TIM15, TIM16 and TIM17.
+
GPIO driver: add new remap parameters for TIM1, TIM15, TIM16, TIM17 and HDMI-CEC: GPIO_Remap_TIM1_DMA, GPIO_Remap_TIM15, GPIO_Remap_TIM16, GPIO_Remap_TIM17, GPIO_Remap_CEC.
+
USART
+driver: add support for Oversampling by 8 mode and onebit method. 2
+functions has been added: USART_OverSampling8Cmd() and
+USART_OneBitMethodCmd().
+
+
DAC
+driver: add new functions handling the DAC under run feature:
+DAC_ITConfig(), DAC_GetFlagStatus(), DAC_ClearFlag(), DAC_GetITStatus()
+and DAC_ClearITPendingBit().
+
DBGMCU driver: add new parameters for TIM15, TIM16 and TIM17: DBGMCU_TIM15_STOP, DBGMCU_TIM16_STOP, DBGMCU_TIM17_STOP.
+
+
FLASH
+driver: the FLASH_EraseOptionBytes() function updated. This is now just
+erasing the option bytes without modifying the RDP status either
+enabled or disabled.
+
PWR
+driver: the PWR_EnterSTOPMode() function updated. When woken up from
+STOP mode, this function resets again the SLEEPDEEP bit in the
+Cortex-M3 System Control register to allow Sleep mode entering.
+
+
+
+
License
+
The
+enclosed firmware and all the related documentation are not covered by
+a License Agreement, if you need such License you can contact your
+local STMicroelectronics office.
+
THE
+PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO
+SAVE TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR
+ANY DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY
+CLAIMS ARISING FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY
+CUSTOMERS OF THE CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH
+THEIR PRODUCTS.
+
+
+
+
For
+complete documentation on STM32(CORTEX M3) 32-Bit Microcontrollers
+visit www.st.com/STM32
+
+
+
+
+
+
+
+
+
+
+
+
+
\ No newline at end of file
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/misc.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/misc.h
new file mode 100644
index 00000000..7d401ca9
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/misc.h
@@ -0,0 +1,220 @@
+/**
+ ******************************************************************************
+ * @file misc.h
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief This file contains all the functions prototypes for the miscellaneous
+ * firmware library functions (add-on to CMSIS functions).
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_FSMC_H
+#define __STM32F10x_FSMC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+ * @{
+ */
+
+/** @addtogroup FSMC
+ * @{
+ */
+
+/** @defgroup FSMC_Exported_Types
+ * @{
+ */
+
+/**
+ * @brief Timing parameters For NOR/SRAM Banks
+ */
+
+typedef struct
+{
+ uint32_t FSMC_AddressSetupTime; /*!< Defines the number of HCLK cycles to configure
+ the duration of the address setup time.
+ This parameter can be a value between 0 and 0xF.
+ @note: It is not used with synchronous NOR Flash memories. */
+
+ uint32_t FSMC_AddressHoldTime; /*!< Defines the number of HCLK cycles to configure
+ the duration of the address hold time.
+ This parameter can be a value between 0 and 0xF.
+ @note: It is not used with synchronous NOR Flash memories.*/
+
+ uint32_t FSMC_DataSetupTime; /*!< Defines the number of HCLK cycles to configure
+ the duration of the data setup time.
+ This parameter can be a value between 0 and 0xFF.
+ @note: It is used for SRAMs, ROMs and asynchronous multiplexed NOR Flash memories. */
+
+ uint32_t FSMC_BusTurnAroundDuration; /*!< Defines the number of HCLK cycles to configure
+ the duration of the bus turnaround.
+ This parameter can be a value between 0 and 0xF.
+ @note: It is only used for multiplexed NOR Flash memories. */
+
+ uint32_t FSMC_CLKDivision; /*!< Defines the period of CLK clock output signal, expressed in number of HCLK cycles.
+ This parameter can be a value between 1 and 0xF.
+ @note: This parameter is not used for asynchronous NOR Flash, SRAM or ROM accesses. */
+
+ uint32_t FSMC_DataLatency; /*!< Defines the number of memory clock cycles to issue
+ to the memory before getting the first data.
+ The value of this parameter depends on the memory type as shown below:
+ - It must be set to 0 in case of a CRAM
+ - It is don't care in asynchronous NOR, SRAM or ROM accesses
+ - It may assume a value between 0 and 0xF in NOR Flash memories
+ with synchronous burst mode enable */
+
+ uint32_t FSMC_AccessMode; /*!< Specifies the asynchronous access mode.
+ This parameter can be a value of @ref FSMC_Access_Mode */
+}FSMC_NORSRAMTimingInitTypeDef;
+
+/**
+ * @brief FSMC NOR/SRAM Init structure definition
+ */
+
+typedef struct
+{
+ uint32_t FSMC_Bank; /*!< Specifies the NOR/SRAM memory bank that will be used.
+ This parameter can be a value of @ref FSMC_NORSRAM_Bank */
+
+ uint32_t FSMC_DataAddressMux; /*!< Specifies whether the address and data values are
+ multiplexed on the databus or not.
+ This parameter can be a value of @ref FSMC_Data_Address_Bus_Multiplexing */
+
+ uint32_t FSMC_MemoryType; /*!< Specifies the type of external memory attached to
+ the corresponding memory bank.
+ This parameter can be a value of @ref FSMC_Memory_Type */
+
+ uint32_t FSMC_MemoryDataWidth; /*!< Specifies the external memory device width.
+ This parameter can be a value of @ref FSMC_Data_Width */
+
+ uint32_t FSMC_BurstAccessMode; /*!< Enables or disables the burst access mode for Flash memory,
+ valid only with synchronous burst Flash memories.
+ This parameter can be a value of @ref FSMC_Burst_Access_Mode */
+
+ uint32_t FSMC_AsynchronousWait; /*!< Enables or disables wait signal during asynchronous transfers,
+ valid only with asynchronous Flash memories.
+ This parameter can be a value of @ref FSMC_AsynchronousWait */
+
+ uint32_t FSMC_WaitSignalPolarity; /*!< Specifies the wait signal polarity, valid only when accessing
+ the Flash memory in burst mode.
+ This parameter can be a value of @ref FSMC_Wait_Signal_Polarity */
+
+ uint32_t FSMC_WrapMode; /*!< Enables or disables the Wrapped burst access mode for Flash
+ memory, valid only when accessing Flash memories in burst mode.
+ This parameter can be a value of @ref FSMC_Wrap_Mode */
+
+ uint32_t FSMC_WaitSignalActive; /*!< Specifies if the wait signal is asserted by the memory one
+ clock cycle before the wait state or during the wait state,
+ valid only when accessing memories in burst mode.
+ This parameter can be a value of @ref FSMC_Wait_Timing */
+
+ uint32_t FSMC_WriteOperation; /*!< Enables or disables the write operation in the selected bank by the FSMC.
+ This parameter can be a value of @ref FSMC_Write_Operation */
+
+ uint32_t FSMC_WaitSignal; /*!< Enables or disables the wait-state insertion via wait
+ signal, valid for Flash memory access in burst mode.
+ This parameter can be a value of @ref FSMC_Wait_Signal */
+
+ uint32_t FSMC_ExtendedMode; /*!< Enables or disables the extended mode.
+ This parameter can be a value of @ref FSMC_Extended_Mode */
+
+ uint32_t FSMC_WriteBurst; /*!< Enables or disables the write burst operation.
+ This parameter can be a value of @ref FSMC_Write_Burst */
+
+ FSMC_NORSRAMTimingInitTypeDef* FSMC_ReadWriteTimingStruct; /*!< Timing Parameters for write and read access if the ExtendedMode is not used*/
+
+ FSMC_NORSRAMTimingInitTypeDef* FSMC_WriteTimingStruct; /*!< Timing Parameters for write access if the ExtendedMode is used*/
+}FSMC_NORSRAMInitTypeDef;
+
+/**
+ * @brief Timing parameters For FSMC NAND and PCCARD Banks
+ */
+
+typedef struct
+{
+ uint32_t FSMC_SetupTime; /*!< Defines the number of HCLK cycles to setup address before
+ the command assertion for NAND-Flash read or write access
+ to common/Attribute or I/O memory space (depending on
+ the memory space timing to be configured).
+ This parameter can be a value between 0 and 0xFF.*/
+
+ uint32_t FSMC_WaitSetupTime; /*!< Defines the minimum number of HCLK cycles to assert the
+ command for NAND-Flash read or write access to
+ common/Attribute or I/O memory space (depending on the
+ memory space timing to be configured).
+ This parameter can be a number between 0x00 and 0xFF */
+
+ uint32_t FSMC_HoldSetupTime; /*!< Defines the number of HCLK clock cycles to hold address
+ (and data for write access) after the command deassertion
+ for NAND-Flash read or write access to common/Attribute
+ or I/O memory space (depending on the memory space timing
+ to be configured).
+ This parameter can be a number between 0x00 and 0xFF */
+
+ uint32_t FSMC_HiZSetupTime; /*!< Defines the number of HCLK clock cycles during which the
+ databus is kept in HiZ after the start of a NAND-Flash
+ write access to common/Attribute or I/O memory space (depending
+ on the memory space timing to be configured).
+ This parameter can be a number between 0x00 and 0xFF */
+}FSMC_NAND_PCCARDTimingInitTypeDef;
+
+/**
+ * @brief FSMC NAND Init structure definition
+ */
+
+typedef struct
+{
+ uint32_t FSMC_Bank; /*!< Specifies the NAND memory bank that will be used.
+ This parameter can be a value of @ref FSMC_NAND_Bank */
+
+ uint32_t FSMC_Waitfeature; /*!< Enables or disables the Wait feature for the NAND Memory Bank.
+ This parameter can be any value of @ref FSMC_Wait_feature */
+
+ uint32_t FSMC_MemoryDataWidth; /*!< Specifies the external memory device width.
+ This parameter can be any value of @ref FSMC_Data_Width */
+
+ uint32_t FSMC_ECC; /*!< Enables or disables the ECC computation.
+ This parameter can be any value of @ref FSMC_ECC */
+
+ uint32_t FSMC_ECCPageSize; /*!< Defines the page size for the extended ECC.
+ This parameter can be any value of @ref FSMC_ECC_Page_Size */
+
+ uint32_t FSMC_TCLRSetupTime; /*!< Defines the number of HCLK cycles to configure the
+ delay between CLE low and RE low.
+ This parameter can be a value between 0 and 0xFF. */
+
+ uint32_t FSMC_TARSetupTime; /*!< Defines the number of HCLK cycles to configure the
+ delay between ALE low and RE low.
+ This parameter can be a number between 0x0 and 0xFF */
+
+ FSMC_NAND_PCCARDTimingInitTypeDef* FSMC_CommonSpaceTimingStruct; /*!< FSMC Common Space Timing */
+
+ FSMC_NAND_PCCARDTimingInitTypeDef* FSMC_AttributeSpaceTimingStruct; /*!< FSMC Attribute Space Timing */
+}FSMC_NANDInitTypeDef;
+
+/**
+ * @brief FSMC PCCARD Init structure definition
+ */
+
+typedef struct
+{
+ uint32_t FSMC_Waitfeature; /*!< Enables or disables the Wait feature for the Memory Bank.
+ This parameter can be any value of @ref FSMC_Wait_feature */
+
+ uint32_t FSMC_TCLRSetupTime; /*!< Defines the number of HCLK cycles to configure the
+ delay between CLE low and RE low.
+ This parameter can be a value between 0 and 0xFF. */
+
+ uint32_t FSMC_TARSetupTime; /*!< Defines the number of HCLK cycles to configure the
+ delay between ALE low and RE low.
+ This parameter can be a number between 0x0 and 0xFF */
+
+
+ FSMC_NAND_PCCARDTimingInitTypeDef* FSMC_CommonSpaceTimingStruct; /*!< FSMC Common Space Timing */
+
+ FSMC_NAND_PCCARDTimingInitTypeDef* FSMC_AttributeSpaceTimingStruct; /*!< FSMC Attribute Space Timing */
+
+ FSMC_NAND_PCCARDTimingInitTypeDef* FSMC_IOSpaceTimingStruct; /*!< FSMC IO Space Timing */
+}FSMC_PCCARDInitTypeDef;
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Exported_Constants
+ * @{
+ */
+
+/** @defgroup FSMC_NORSRAM_Bank
+ * @{
+ */
+#define FSMC_Bank1_NORSRAM1 ((uint32_t)0x00000000)
+#define FSMC_Bank1_NORSRAM2 ((uint32_t)0x00000002)
+#define FSMC_Bank1_NORSRAM3 ((uint32_t)0x00000004)
+#define FSMC_Bank1_NORSRAM4 ((uint32_t)0x00000006)
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_NAND_Bank
+ * @{
+ */
+#define FSMC_Bank2_NAND ((uint32_t)0x00000010)
+#define FSMC_Bank3_NAND ((uint32_t)0x00000100)
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_PCCARD_Bank
+ * @{
+ */
+#define FSMC_Bank4_PCCARD ((uint32_t)0x00001000)
+/**
+ * @}
+ */
+
+#define IS_FSMC_NORSRAM_BANK(BANK) (((BANK) == FSMC_Bank1_NORSRAM1) || \
+ ((BANK) == FSMC_Bank1_NORSRAM2) || \
+ ((BANK) == FSMC_Bank1_NORSRAM3) || \
+ ((BANK) == FSMC_Bank1_NORSRAM4))
+
+#define IS_FSMC_NAND_BANK(BANK) (((BANK) == FSMC_Bank2_NAND) || \
+ ((BANK) == FSMC_Bank3_NAND))
+
+#define IS_FSMC_GETFLAG_BANK(BANK) (((BANK) == FSMC_Bank2_NAND) || \
+ ((BANK) == FSMC_Bank3_NAND) || \
+ ((BANK) == FSMC_Bank4_PCCARD))
+
+#define IS_FSMC_IT_BANK(BANK) (((BANK) == FSMC_Bank2_NAND) || \
+ ((BANK) == FSMC_Bank3_NAND) || \
+ ((BANK) == FSMC_Bank4_PCCARD))
+
+/** @defgroup NOR_SRAM_Controller
+ * @{
+ */
+
+/** @defgroup FSMC_Data_Address_Bus_Multiplexing
+ * @{
+ */
+
+#define FSMC_DataAddressMux_Disable ((uint32_t)0x00000000)
+#define FSMC_DataAddressMux_Enable ((uint32_t)0x00000002)
+#define IS_FSMC_MUX(MUX) (((MUX) == FSMC_DataAddressMux_Disable) || \
+ ((MUX) == FSMC_DataAddressMux_Enable))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Memory_Type
+ * @{
+ */
+
+#define FSMC_MemoryType_SRAM ((uint32_t)0x00000000)
+#define FSMC_MemoryType_PSRAM ((uint32_t)0x00000004)
+#define FSMC_MemoryType_NOR ((uint32_t)0x00000008)
+#define IS_FSMC_MEMORY(MEMORY) (((MEMORY) == FSMC_MemoryType_SRAM) || \
+ ((MEMORY) == FSMC_MemoryType_PSRAM)|| \
+ ((MEMORY) == FSMC_MemoryType_NOR))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Data_Width
+ * @{
+ */
+
+#define FSMC_MemoryDataWidth_8b ((uint32_t)0x00000000)
+#define FSMC_MemoryDataWidth_16b ((uint32_t)0x00000010)
+#define IS_FSMC_MEMORY_WIDTH(WIDTH) (((WIDTH) == FSMC_MemoryDataWidth_8b) || \
+ ((WIDTH) == FSMC_MemoryDataWidth_16b))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Burst_Access_Mode
+ * @{
+ */
+
+#define FSMC_BurstAccessMode_Disable ((uint32_t)0x00000000)
+#define FSMC_BurstAccessMode_Enable ((uint32_t)0x00000100)
+#define IS_FSMC_BURSTMODE(STATE) (((STATE) == FSMC_BurstAccessMode_Disable) || \
+ ((STATE) == FSMC_BurstAccessMode_Enable))
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_AsynchronousWait
+ * @{
+ */
+#define FSMC_AsynchronousWait_Disable ((uint32_t)0x00000000)
+#define FSMC_AsynchronousWait_Enable ((uint32_t)0x00008000)
+#define IS_FSMC_ASYNWAIT(STATE) (((STATE) == FSMC_AsynchronousWait_Disable) || \
+ ((STATE) == FSMC_AsynchronousWait_Enable))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Wait_Signal_Polarity
+ * @{
+ */
+
+#define FSMC_WaitSignalPolarity_Low ((uint32_t)0x00000000)
+#define FSMC_WaitSignalPolarity_High ((uint32_t)0x00000200)
+#define IS_FSMC_WAIT_POLARITY(POLARITY) (((POLARITY) == FSMC_WaitSignalPolarity_Low) || \
+ ((POLARITY) == FSMC_WaitSignalPolarity_High))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Wrap_Mode
+ * @{
+ */
+
+#define FSMC_WrapMode_Disable ((uint32_t)0x00000000)
+#define FSMC_WrapMode_Enable ((uint32_t)0x00000400)
+#define IS_FSMC_WRAP_MODE(MODE) (((MODE) == FSMC_WrapMode_Disable) || \
+ ((MODE) == FSMC_WrapMode_Enable))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Wait_Timing
+ * @{
+ */
+
+#define FSMC_WaitSignalActive_BeforeWaitState ((uint32_t)0x00000000)
+#define FSMC_WaitSignalActive_DuringWaitState ((uint32_t)0x00000800)
+#define IS_FSMC_WAIT_SIGNAL_ACTIVE(ACTIVE) (((ACTIVE) == FSMC_WaitSignalActive_BeforeWaitState) || \
+ ((ACTIVE) == FSMC_WaitSignalActive_DuringWaitState))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Write_Operation
+ * @{
+ */
+
+#define FSMC_WriteOperation_Disable ((uint32_t)0x00000000)
+#define FSMC_WriteOperation_Enable ((uint32_t)0x00001000)
+#define IS_FSMC_WRITE_OPERATION(OPERATION) (((OPERATION) == FSMC_WriteOperation_Disable) || \
+ ((OPERATION) == FSMC_WriteOperation_Enable))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Wait_Signal
+ * @{
+ */
+
+#define FSMC_WaitSignal_Disable ((uint32_t)0x00000000)
+#define FSMC_WaitSignal_Enable ((uint32_t)0x00002000)
+#define IS_FSMC_WAITE_SIGNAL(SIGNAL) (((SIGNAL) == FSMC_WaitSignal_Disable) || \
+ ((SIGNAL) == FSMC_WaitSignal_Enable))
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Extended_Mode
+ * @{
+ */
+
+#define FSMC_ExtendedMode_Disable ((uint32_t)0x00000000)
+#define FSMC_ExtendedMode_Enable ((uint32_t)0x00004000)
+
+#define IS_FSMC_EXTENDED_MODE(MODE) (((MODE) == FSMC_ExtendedMode_Disable) || \
+ ((MODE) == FSMC_ExtendedMode_Enable))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Write_Burst
+ * @{
+ */
+
+#define FSMC_WriteBurst_Disable ((uint32_t)0x00000000)
+#define FSMC_WriteBurst_Enable ((uint32_t)0x00080000)
+#define IS_FSMC_WRITE_BURST(BURST) (((BURST) == FSMC_WriteBurst_Disable) || \
+ ((BURST) == FSMC_WriteBurst_Enable))
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Address_Setup_Time
+ * @{
+ */
+
+#define IS_FSMC_ADDRESS_SETUP_TIME(TIME) ((TIME) <= 0xF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Address_Hold_Time
+ * @{
+ */
+
+#define IS_FSMC_ADDRESS_HOLD_TIME(TIME) ((TIME) <= 0xF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Data_Setup_Time
+ * @{
+ */
+
+#define IS_FSMC_DATASETUP_TIME(TIME) (((TIME) > 0) && ((TIME) <= 0xFF))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Bus_Turn_around_Duration
+ * @{
+ */
+
+#define IS_FSMC_TURNAROUND_TIME(TIME) ((TIME) <= 0xF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_CLK_Division
+ * @{
+ */
+
+#define IS_FSMC_CLK_DIV(DIV) ((DIV) <= 0xF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Data_Latency
+ * @{
+ */
+
+#define IS_FSMC_DATA_LATENCY(LATENCY) ((LATENCY) <= 0xF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Access_Mode
+ * @{
+ */
+
+#define FSMC_AccessMode_A ((uint32_t)0x00000000)
+#define FSMC_AccessMode_B ((uint32_t)0x10000000)
+#define FSMC_AccessMode_C ((uint32_t)0x20000000)
+#define FSMC_AccessMode_D ((uint32_t)0x30000000)
+#define IS_FSMC_ACCESS_MODE(MODE) (((MODE) == FSMC_AccessMode_A) || \
+ ((MODE) == FSMC_AccessMode_B) || \
+ ((MODE) == FSMC_AccessMode_C) || \
+ ((MODE) == FSMC_AccessMode_D))
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup NAND_PCCARD_Controller
+ * @{
+ */
+
+/** @defgroup FSMC_Wait_feature
+ * @{
+ */
+
+#define FSMC_Waitfeature_Disable ((uint32_t)0x00000000)
+#define FSMC_Waitfeature_Enable ((uint32_t)0x00000002)
+#define IS_FSMC_WAIT_FEATURE(FEATURE) (((FEATURE) == FSMC_Waitfeature_Disable) || \
+ ((FEATURE) == FSMC_Waitfeature_Enable))
+
+/**
+ * @}
+ */
+
+
+/** @defgroup FSMC_ECC
+ * @{
+ */
+
+#define FSMC_ECC_Disable ((uint32_t)0x00000000)
+#define FSMC_ECC_Enable ((uint32_t)0x00000040)
+#define IS_FSMC_ECC_STATE(STATE) (((STATE) == FSMC_ECC_Disable) || \
+ ((STATE) == FSMC_ECC_Enable))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_ECC_Page_Size
+ * @{
+ */
+
+#define FSMC_ECCPageSize_256Bytes ((uint32_t)0x00000000)
+#define FSMC_ECCPageSize_512Bytes ((uint32_t)0x00020000)
+#define FSMC_ECCPageSize_1024Bytes ((uint32_t)0x00040000)
+#define FSMC_ECCPageSize_2048Bytes ((uint32_t)0x00060000)
+#define FSMC_ECCPageSize_4096Bytes ((uint32_t)0x00080000)
+#define FSMC_ECCPageSize_8192Bytes ((uint32_t)0x000A0000)
+#define IS_FSMC_ECCPAGE_SIZE(SIZE) (((SIZE) == FSMC_ECCPageSize_256Bytes) || \
+ ((SIZE) == FSMC_ECCPageSize_512Bytes) || \
+ ((SIZE) == FSMC_ECCPageSize_1024Bytes) || \
+ ((SIZE) == FSMC_ECCPageSize_2048Bytes) || \
+ ((SIZE) == FSMC_ECCPageSize_4096Bytes) || \
+ ((SIZE) == FSMC_ECCPageSize_8192Bytes))
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_TCLR_Setup_Time
+ * @{
+ */
+
+#define IS_FSMC_TCLR_TIME(TIME) ((TIME) <= 0xFF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_TAR_Setup_Time
+ * @{
+ */
+
+#define IS_FSMC_TAR_TIME(TIME) ((TIME) <= 0xFF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Setup_Time
+ * @{
+ */
+
+#define IS_FSMC_SETUP_TIME(TIME) ((TIME) <= 0xFF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Wait_Setup_Time
+ * @{
+ */
+
+#define IS_FSMC_WAIT_TIME(TIME) ((TIME) <= 0xFF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Hold_Setup_Time
+ * @{
+ */
+
+#define IS_FSMC_HOLD_TIME(TIME) ((TIME) <= 0xFF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_HiZ_Setup_Time
+ * @{
+ */
+
+#define IS_FSMC_HIZ_TIME(TIME) ((TIME) <= 0xFF)
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Interrupt_sources
+ * @{
+ */
+
+#define FSMC_IT_RisingEdge ((uint32_t)0x00000008)
+#define FSMC_IT_Level ((uint32_t)0x00000010)
+#define FSMC_IT_FallingEdge ((uint32_t)0x00000020)
+#define IS_FSMC_IT(IT) ((((IT) & (uint32_t)0xFFFFFFC7) == 0x00000000) && ((IT) != 0x00000000))
+#define IS_FSMC_GET_IT(IT) (((IT) == FSMC_IT_RisingEdge) || \
+ ((IT) == FSMC_IT_Level) || \
+ ((IT) == FSMC_IT_FallingEdge))
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Flags
+ * @{
+ */
+
+#define FSMC_FLAG_RisingEdge ((uint32_t)0x00000001)
+#define FSMC_FLAG_Level ((uint32_t)0x00000002)
+#define FSMC_FLAG_FallingEdge ((uint32_t)0x00000004)
+#define FSMC_FLAG_FEMPT ((uint32_t)0x00000040)
+#define IS_FSMC_GET_FLAG(FLAG) (((FLAG) == FSMC_FLAG_RisingEdge) || \
+ ((FLAG) == FSMC_FLAG_Level) || \
+ ((FLAG) == FSMC_FLAG_FallingEdge) || \
+ ((FLAG) == FSMC_FLAG_FEMPT))
+
+#define IS_FSMC_CLEAR_FLAG(FLAG) ((((FLAG) & (uint32_t)0xFFFFFFF8) == 0x00000000) && ((FLAG) != 0x00000000))
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Exported_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup FSMC_Exported_Functions
+ * @{
+ */
+
+void FSMC_NORSRAMDeInit(uint32_t FSMC_Bank);
+void FSMC_NANDDeInit(uint32_t FSMC_Bank);
+void FSMC_PCCARDDeInit(void);
+void FSMC_NORSRAMInit(FSMC_NORSRAMInitTypeDef* FSMC_NORSRAMInitStruct);
+void FSMC_NANDInit(FSMC_NANDInitTypeDef* FSMC_NANDInitStruct);
+void FSMC_PCCARDInit(FSMC_PCCARDInitTypeDef* FSMC_PCCARDInitStruct);
+void FSMC_NORSRAMStructInit(FSMC_NORSRAMInitTypeDef* FSMC_NORSRAMInitStruct);
+void FSMC_NANDStructInit(FSMC_NANDInitTypeDef* FSMC_NANDInitStruct);
+void FSMC_PCCARDStructInit(FSMC_PCCARDInitTypeDef* FSMC_PCCARDInitStruct);
+void FSMC_NORSRAMCmd(uint32_t FSMC_Bank, FunctionalState NewState);
+void FSMC_NANDCmd(uint32_t FSMC_Bank, FunctionalState NewState);
+void FSMC_PCCARDCmd(FunctionalState NewState);
+void FSMC_NANDECCCmd(uint32_t FSMC_Bank, FunctionalState NewState);
+uint32_t FSMC_GetECC(uint32_t FSMC_Bank);
+void FSMC_ITConfig(uint32_t FSMC_Bank, uint32_t FSMC_IT, FunctionalState NewState);
+FlagStatus FSMC_GetFlagStatus(uint32_t FSMC_Bank, uint32_t FSMC_FLAG);
+void FSMC_ClearFlag(uint32_t FSMC_Bank, uint32_t FSMC_FLAG);
+ITStatus FSMC_GetITStatus(uint32_t FSMC_Bank, uint32_t FSMC_IT);
+void FSMC_ClearITPendingBit(uint32_t FSMC_Bank, uint32_t FSMC_IT);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /*__STM32F10x_FSMC_H */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_gpio.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_gpio.h
new file mode 100644
index 00000000..b8aa49a2
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_gpio.h
@@ -0,0 +1,385 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x_gpio.h
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief This file contains all the functions prototypes for the GPIO
+ * firmware library.
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_I2C_H
+#define __STM32F10x_I2C_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+ * @{
+ */
+
+/** @addtogroup I2C
+ * @{
+ */
+
+/** @defgroup I2C_Exported_Types
+ * @{
+ */
+
+/**
+ * @brief I2C Init structure definition
+ */
+
+typedef struct
+{
+ uint32_t I2C_ClockSpeed; /*!< Specifies the clock frequency.
+ This parameter must be set to a value lower than 400kHz */
+
+ uint16_t I2C_Mode; /*!< Specifies the I2C mode.
+ This parameter can be a value of @ref I2C_mode */
+
+ uint16_t I2C_DutyCycle; /*!< Specifies the I2C fast mode duty cycle.
+ This parameter can be a value of @ref I2C_duty_cycle_in_fast_mode */
+
+ uint16_t I2C_OwnAddress1; /*!< Specifies the first device own address.
+ This parameter can be a 7-bit or 10-bit address. */
+
+ uint16_t I2C_Ack; /*!< Enables or disables the acknowledgement.
+ This parameter can be a value of @ref I2C_acknowledgement */
+
+ uint16_t I2C_AcknowledgedAddress; /*!< Specifies if 7-bit or 10-bit address is acknowledged.
+ This parameter can be a value of @ref I2C_acknowledged_address */
+}I2C_InitTypeDef;
+
+/**
+ * @}
+ */
+
+
+/** @defgroup I2C_Exported_Constants
+ * @{
+ */
+
+#define IS_I2C_ALL_PERIPH(PERIPH) (((PERIPH) == I2C1) || \
+ ((PERIPH) == I2C2))
+/** @defgroup I2C_mode
+ * @{
+ */
+
+#define I2C_Mode_I2C ((uint16_t)0x0000)
+#define I2C_Mode_SMBusDevice ((uint16_t)0x0002)
+#define I2C_Mode_SMBusHost ((uint16_t)0x000A)
+#define IS_I2C_MODE(MODE) (((MODE) == I2C_Mode_I2C) || \
+ ((MODE) == I2C_Mode_SMBusDevice) || \
+ ((MODE) == I2C_Mode_SMBusHost))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_duty_cycle_in_fast_mode
+ * @{
+ */
+
+#define I2C_DutyCycle_16_9 ((uint16_t)0x4000) /*!< I2C fast mode Tlow/Thigh = 16/9 */
+#define I2C_DutyCycle_2 ((uint16_t)0xBFFF) /*!< I2C fast mode Tlow/Thigh = 2 */
+#define IS_I2C_DUTY_CYCLE(CYCLE) (((CYCLE) == I2C_DutyCycle_16_9) || \
+ ((CYCLE) == I2C_DutyCycle_2))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_acknowledgement
+ * @{
+ */
+
+#define I2C_Ack_Enable ((uint16_t)0x0400)
+#define I2C_Ack_Disable ((uint16_t)0x0000)
+#define IS_I2C_ACK_STATE(STATE) (((STATE) == I2C_Ack_Enable) || \
+ ((STATE) == I2C_Ack_Disable))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_transfer_direction
+ * @{
+ */
+
+#define I2C_Direction_Transmitter ((uint8_t)0x00)
+#define I2C_Direction_Receiver ((uint8_t)0x01)
+#define IS_I2C_DIRECTION(DIRECTION) (((DIRECTION) == I2C_Direction_Transmitter) || \
+ ((DIRECTION) == I2C_Direction_Receiver))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_acknowledged_address
+ * @{
+ */
+
+#define I2C_AcknowledgedAddress_7bit ((uint16_t)0x4000)
+#define I2C_AcknowledgedAddress_10bit ((uint16_t)0xC000)
+#define IS_I2C_ACKNOWLEDGE_ADDRESS(ADDRESS) (((ADDRESS) == I2C_AcknowledgedAddress_7bit) || \
+ ((ADDRESS) == I2C_AcknowledgedAddress_10bit))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_registers
+ * @{
+ */
+
+#define I2C_Register_CR1 ((uint8_t)0x00)
+#define I2C_Register_CR2 ((uint8_t)0x04)
+#define I2C_Register_OAR1 ((uint8_t)0x08)
+#define I2C_Register_OAR2 ((uint8_t)0x0C)
+#define I2C_Register_DR ((uint8_t)0x10)
+#define I2C_Register_SR1 ((uint8_t)0x14)
+#define I2C_Register_SR2 ((uint8_t)0x18)
+#define I2C_Register_CCR ((uint8_t)0x1C)
+#define I2C_Register_TRISE ((uint8_t)0x20)
+#define IS_I2C_REGISTER(REGISTER) (((REGISTER) == I2C_Register_CR1) || \
+ ((REGISTER) == I2C_Register_CR2) || \
+ ((REGISTER) == I2C_Register_OAR1) || \
+ ((REGISTER) == I2C_Register_OAR2) || \
+ ((REGISTER) == I2C_Register_DR) || \
+ ((REGISTER) == I2C_Register_SR1) || \
+ ((REGISTER) == I2C_Register_SR2) || \
+ ((REGISTER) == I2C_Register_CCR) || \
+ ((REGISTER) == I2C_Register_TRISE))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_SMBus_alert_pin_level
+ * @{
+ */
+
+#define I2C_SMBusAlert_Low ((uint16_t)0x2000)
+#define I2C_SMBusAlert_High ((uint16_t)0xDFFF)
+#define IS_I2C_SMBUS_ALERT(ALERT) (((ALERT) == I2C_SMBusAlert_Low) || \
+ ((ALERT) == I2C_SMBusAlert_High))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_PEC_position
+ * @{
+ */
+
+#define I2C_PECPosition_Next ((uint16_t)0x0800)
+#define I2C_PECPosition_Current ((uint16_t)0xF7FF)
+#define IS_I2C_PEC_POSITION(POSITION) (((POSITION) == I2C_PECPosition_Next) || \
+ ((POSITION) == I2C_PECPosition_Current))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_NCAK_position
+ * @{
+ */
+
+#define I2C_NACKPosition_Next ((uint16_t)0x0800)
+#define I2C_NACKPosition_Current ((uint16_t)0xF7FF)
+#define IS_I2C_NACK_POSITION(POSITION) (((POSITION) == I2C_NACKPosition_Next) || \
+ ((POSITION) == I2C_NACKPosition_Current))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_interrupts_definition
+ * @{
+ */
+
+#define I2C_IT_BUF ((uint16_t)0x0400)
+#define I2C_IT_EVT ((uint16_t)0x0200)
+#define I2C_IT_ERR ((uint16_t)0x0100)
+#define IS_I2C_CONFIG_IT(IT) ((((IT) & (uint16_t)0xF8FF) == 0x00) && ((IT) != 0x00))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_interrupts_definition
+ * @{
+ */
+
+#define I2C_IT_SMBALERT ((uint32_t)0x01008000)
+#define I2C_IT_TIMEOUT ((uint32_t)0x01004000)
+#define I2C_IT_PECERR ((uint32_t)0x01001000)
+#define I2C_IT_OVR ((uint32_t)0x01000800)
+#define I2C_IT_AF ((uint32_t)0x01000400)
+#define I2C_IT_ARLO ((uint32_t)0x01000200)
+#define I2C_IT_BERR ((uint32_t)0x01000100)
+#define I2C_IT_TXE ((uint32_t)0x06000080)
+#define I2C_IT_RXNE ((uint32_t)0x06000040)
+#define I2C_IT_STOPF ((uint32_t)0x02000010)
+#define I2C_IT_ADD10 ((uint32_t)0x02000008)
+#define I2C_IT_BTF ((uint32_t)0x02000004)
+#define I2C_IT_ADDR ((uint32_t)0x02000002)
+#define I2C_IT_SB ((uint32_t)0x02000001)
+
+#define IS_I2C_CLEAR_IT(IT) ((((IT) & (uint16_t)0x20FF) == 0x00) && ((IT) != (uint16_t)0x00))
+
+#define IS_I2C_GET_IT(IT) (((IT) == I2C_IT_SMBALERT) || ((IT) == I2C_IT_TIMEOUT) || \
+ ((IT) == I2C_IT_PECERR) || ((IT) == I2C_IT_OVR) || \
+ ((IT) == I2C_IT_AF) || ((IT) == I2C_IT_ARLO) || \
+ ((IT) == I2C_IT_BERR) || ((IT) == I2C_IT_TXE) || \
+ ((IT) == I2C_IT_RXNE) || ((IT) == I2C_IT_STOPF) || \
+ ((IT) == I2C_IT_ADD10) || ((IT) == I2C_IT_BTF) || \
+ ((IT) == I2C_IT_ADDR) || ((IT) == I2C_IT_SB))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_flags_definition
+ * @{
+ */
+
+/**
+ * @brief SR2 register flags
+ */
+
+#define I2C_FLAG_DUALF ((uint32_t)0x00800000)
+#define I2C_FLAG_SMBHOST ((uint32_t)0x00400000)
+#define I2C_FLAG_SMBDEFAULT ((uint32_t)0x00200000)
+#define I2C_FLAG_GENCALL ((uint32_t)0x00100000)
+#define I2C_FLAG_TRA ((uint32_t)0x00040000)
+#define I2C_FLAG_BUSY ((uint32_t)0x00020000)
+#define I2C_FLAG_MSL ((uint32_t)0x00010000)
+
+/**
+ * @brief SR1 register flags
+ */
+
+#define I2C_FLAG_SMBALERT ((uint32_t)0x10008000)
+#define I2C_FLAG_TIMEOUT ((uint32_t)0x10004000)
+#define I2C_FLAG_PECERR ((uint32_t)0x10001000)
+#define I2C_FLAG_OVR ((uint32_t)0x10000800)
+#define I2C_FLAG_AF ((uint32_t)0x10000400)
+#define I2C_FLAG_ARLO ((uint32_t)0x10000200)
+#define I2C_FLAG_BERR ((uint32_t)0x10000100)
+#define I2C_FLAG_TXE ((uint32_t)0x10000080)
+#define I2C_FLAG_RXNE ((uint32_t)0x10000040)
+#define I2C_FLAG_STOPF ((uint32_t)0x10000010)
+#define I2C_FLAG_ADD10 ((uint32_t)0x10000008)
+#define I2C_FLAG_BTF ((uint32_t)0x10000004)
+#define I2C_FLAG_ADDR ((uint32_t)0x10000002)
+#define I2C_FLAG_SB ((uint32_t)0x10000001)
+
+#define IS_I2C_CLEAR_FLAG(FLAG) ((((FLAG) & (uint16_t)0x20FF) == 0x00) && ((FLAG) != (uint16_t)0x00))
+
+#define IS_I2C_GET_FLAG(FLAG) (((FLAG) == I2C_FLAG_DUALF) || ((FLAG) == I2C_FLAG_SMBHOST) || \
+ ((FLAG) == I2C_FLAG_SMBDEFAULT) || ((FLAG) == I2C_FLAG_GENCALL) || \
+ ((FLAG) == I2C_FLAG_TRA) || ((FLAG) == I2C_FLAG_BUSY) || \
+ ((FLAG) == I2C_FLAG_MSL) || ((FLAG) == I2C_FLAG_SMBALERT) || \
+ ((FLAG) == I2C_FLAG_TIMEOUT) || ((FLAG) == I2C_FLAG_PECERR) || \
+ ((FLAG) == I2C_FLAG_OVR) || ((FLAG) == I2C_FLAG_AF) || \
+ ((FLAG) == I2C_FLAG_ARLO) || ((FLAG) == I2C_FLAG_BERR) || \
+ ((FLAG) == I2C_FLAG_TXE) || ((FLAG) == I2C_FLAG_RXNE) || \
+ ((FLAG) == I2C_FLAG_STOPF) || ((FLAG) == I2C_FLAG_ADD10) || \
+ ((FLAG) == I2C_FLAG_BTF) || ((FLAG) == I2C_FLAG_ADDR) || \
+ ((FLAG) == I2C_FLAG_SB))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_Events
+ * @{
+ */
+
+/*========================================
+
+ I2C Master Events (Events grouped in order of communication)
+ ==========================================*/
+/**
+ * @brief Communication start
+ *
+ * After sending the START condition (I2C_GenerateSTART() function) the master
+ * has to wait for this event. It means that the Start condition has been correctly
+ * released on the I2C bus (the bus is free, no other devices is communicating).
+ *
+ */
+/* --EV5 */
+#define I2C_EVENT_MASTER_MODE_SELECT ((uint32_t)0x00030001) /* BUSY, MSL and SB flag */
+
+/**
+ * @brief Address Acknowledge
+ *
+ * After checking on EV5 (start condition correctly released on the bus), the
+ * master sends the address of the slave(s) with which it will communicate
+ * (I2C_Send7bitAddress() function, it also determines the direction of the communication:
+ * Master transmitter or Receiver). Then the master has to wait that a slave acknowledges
+ * his address. If an acknowledge is sent on the bus, one of the following events will
+ * be set:
+ *
+ * 1) In case of Master Receiver (7-bit addressing): the I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED
+ * event is set.
+ *
+ * 2) In case of Master Transmitter (7-bit addressing): the I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED
+ * is set
+ *
+ * 3) In case of 10-Bit addressing mode, the master (just after generating the START
+ * and checking on EV5) has to send the header of 10-bit addressing mode (I2C_SendData()
+ * function). Then master should wait on EV9. It means that the 10-bit addressing
+ * header has been correctly sent on the bus. Then master should send the second part of
+ * the 10-bit address (LSB) using the function I2C_Send7bitAddress(). Then master
+ * should wait for event EV6.
+ *
+ */
+
+/* --EV6 */
+#define I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED ((uint32_t)0x00070082) /* BUSY, MSL, ADDR, TXE and TRA flags */
+#define I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED ((uint32_t)0x00030002) /* BUSY, MSL and ADDR flags */
+/* --EV9 */
+#define I2C_EVENT_MASTER_MODE_ADDRESS10 ((uint32_t)0x00030008) /* BUSY, MSL and ADD10 flags */
+
+/**
+ * @brief Communication events
+ *
+ * If a communication is established (START condition generated and slave address
+ * acknowledged) then the master has to check on one of the following events for
+ * communication procedures:
+ *
+ * 1) Master Receiver mode: The master has to wait on the event EV7 then to read
+ * the data received from the slave (I2C_ReceiveData() function).
+ *
+ * 2) Master Transmitter mode: The master has to send data (I2C_SendData()
+ * function) then to wait on event EV8 or EV8_2.
+ * These two events are similar:
+ * - EV8 means that the data has been written in the data register and is
+ * being shifted out.
+ * - EV8_2 means that the data has been physically shifted out and output
+ * on the bus.
+ * In most cases, using EV8 is sufficient for the application.
+ * Using EV8_2 leads to a slower communication but ensure more reliable test.
+ * EV8_2 is also more suitable than EV8 for testing on the last data transmission
+ * (before Stop condition generation).
+ *
+ * @note In case the user software does not guarantee that this event EV7 is
+ * managed before the current byte end of transfer, then user may check on EV7
+ * and BTF flag at the same time (ie. (I2C_EVENT_MASTER_BYTE_RECEIVED | I2C_FLAG_BTF)).
+ * In this case the communication may be slower.
+ *
+ */
+
+/* Master RECEIVER mode -----------------------------*/
+/* --EV7 */
+#define I2C_EVENT_MASTER_BYTE_RECEIVED ((uint32_t)0x00030040) /* BUSY, MSL and RXNE flags */
+
+/* Master TRANSMITTER mode --------------------------*/
+/* --EV8 */
+#define I2C_EVENT_MASTER_BYTE_TRANSMITTING ((uint32_t)0x00070080) /* TRA, BUSY, MSL, TXE flags */
+/* --EV8_2 */
+#define I2C_EVENT_MASTER_BYTE_TRANSMITTED ((uint32_t)0x00070084) /* TRA, BUSY, MSL, TXE and BTF flags */
+
+
+/*========================================
+
+ I2C Slave Events (Events grouped in order of communication)
+ ==========================================*/
+
+/**
+ * @brief Communication start events
+ *
+ * Wait on one of these events at the start of the communication. It means that
+ * the I2C peripheral detected a Start condition on the bus (generated by master
+ * device) followed by the peripheral address. The peripheral generates an ACK
+ * condition on the bus (if the acknowledge feature is enabled through function
+ * I2C_AcknowledgeConfig()) and the events listed above are set :
+ *
+ * 1) In normal case (only one address managed by the slave), when the address
+ * sent by the master matches the own address of the peripheral (configured by
+ * I2C_OwnAddress1 field) the I2C_EVENT_SLAVE_XXX_ADDRESS_MATCHED event is set
+ * (where XXX could be TRANSMITTER or RECEIVER).
+ *
+ * 2) In case the address sent by the master matches the second address of the
+ * peripheral (configured by the function I2C_OwnAddress2Config() and enabled
+ * by the function I2C_DualAddressCmd()) the events I2C_EVENT_SLAVE_XXX_SECONDADDRESS_MATCHED
+ * (where XXX could be TRANSMITTER or RECEIVER) are set.
+ *
+ * 3) In case the address sent by the master is General Call (address 0x00) and
+ * if the General Call is enabled for the peripheral (using function I2C_GeneralCallCmd())
+ * the following event is set I2C_EVENT_SLAVE_GENERALCALLADDRESS_MATCHED.
+ *
+ */
+
+/* --EV1 (all the events below are variants of EV1) */
+/* 1) Case of One Single Address managed by the slave */
+#define I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED ((uint32_t)0x00020002) /* BUSY and ADDR flags */
+#define I2C_EVENT_SLAVE_TRANSMITTER_ADDRESS_MATCHED ((uint32_t)0x00060082) /* TRA, BUSY, TXE and ADDR flags */
+
+/* 2) Case of Dual address managed by the slave */
+#define I2C_EVENT_SLAVE_RECEIVER_SECONDADDRESS_MATCHED ((uint32_t)0x00820000) /* DUALF and BUSY flags */
+#define I2C_EVENT_SLAVE_TRANSMITTER_SECONDADDRESS_MATCHED ((uint32_t)0x00860080) /* DUALF, TRA, BUSY and TXE flags */
+
+/* 3) Case of General Call enabled for the slave */
+#define I2C_EVENT_SLAVE_GENERALCALLADDRESS_MATCHED ((uint32_t)0x00120000) /* GENCALL and BUSY flags */
+
+/**
+ * @brief Communication events
+ *
+ * Wait on one of these events when EV1 has already been checked and:
+ *
+ * - Slave RECEIVER mode:
+ * - EV2: When the application is expecting a data byte to be received.
+ * - EV4: When the application is expecting the end of the communication: master
+ * sends a stop condition and data transmission is stopped.
+ *
+ * - Slave Transmitter mode:
+ * - EV3: When a byte has been transmitted by the slave and the application is expecting
+ * the end of the byte transmission. The two events I2C_EVENT_SLAVE_BYTE_TRANSMITTED and
+ * I2C_EVENT_SLAVE_BYTE_TRANSMITTING are similar. The second one can optionally be
+ * used when the user software doesn't guarantee the EV3 is managed before the
+ * current byte end of transfer.
+ * - EV3_2: When the master sends a NACK in order to tell slave that data transmission
+ * shall end (before sending the STOP condition). In this case slave has to stop sending
+ * data bytes and expect a Stop condition on the bus.
+ *
+ * @note In case the user software does not guarantee that the event EV2 is
+ * managed before the current byte end of transfer, then user may check on EV2
+ * and BTF flag at the same time (ie. (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_BTF)).
+ * In this case the communication may be slower.
+ *
+ */
+
+/* Slave RECEIVER mode --------------------------*/
+/* --EV2 */
+#define I2C_EVENT_SLAVE_BYTE_RECEIVED ((uint32_t)0x00020040) /* BUSY and RXNE flags */
+/* --EV4 */
+#define I2C_EVENT_SLAVE_STOP_DETECTED ((uint32_t)0x00000010) /* STOPF flag */
+
+/* Slave TRANSMITTER mode -----------------------*/
+/* --EV3 */
+#define I2C_EVENT_SLAVE_BYTE_TRANSMITTED ((uint32_t)0x00060084) /* TRA, BUSY, TXE and BTF flags */
+#define I2C_EVENT_SLAVE_BYTE_TRANSMITTING ((uint32_t)0x00060080) /* TRA, BUSY and TXE flags */
+/* --EV3_2 */
+#define I2C_EVENT_SLAVE_ACK_FAILURE ((uint32_t)0x00000400) /* AF flag */
+
+/*=========================== End of Events Description ==========================================*/
+
+#define IS_I2C_EVENT(EVENT) (((EVENT) == I2C_EVENT_SLAVE_TRANSMITTER_ADDRESS_MATCHED) || \
+ ((EVENT) == I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED) || \
+ ((EVENT) == I2C_EVENT_SLAVE_TRANSMITTER_SECONDADDRESS_MATCHED) || \
+ ((EVENT) == I2C_EVENT_SLAVE_RECEIVER_SECONDADDRESS_MATCHED) || \
+ ((EVENT) == I2C_EVENT_SLAVE_GENERALCALLADDRESS_MATCHED) || \
+ ((EVENT) == I2C_EVENT_SLAVE_BYTE_RECEIVED) || \
+ ((EVENT) == (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_DUALF)) || \
+ ((EVENT) == (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_GENCALL)) || \
+ ((EVENT) == I2C_EVENT_SLAVE_BYTE_TRANSMITTED) || \
+ ((EVENT) == (I2C_EVENT_SLAVE_BYTE_TRANSMITTED | I2C_FLAG_DUALF)) || \
+ ((EVENT) == (I2C_EVENT_SLAVE_BYTE_TRANSMITTED | I2C_FLAG_GENCALL)) || \
+ ((EVENT) == I2C_EVENT_SLAVE_STOP_DETECTED) || \
+ ((EVENT) == I2C_EVENT_MASTER_MODE_SELECT) || \
+ ((EVENT) == I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED) || \
+ ((EVENT) == I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED) || \
+ ((EVENT) == I2C_EVENT_MASTER_BYTE_RECEIVED) || \
+ ((EVENT) == I2C_EVENT_MASTER_BYTE_TRANSMITTED) || \
+ ((EVENT) == I2C_EVENT_MASTER_BYTE_TRANSMITTING) || \
+ ((EVENT) == I2C_EVENT_MASTER_MODE_ADDRESS10) || \
+ ((EVENT) == I2C_EVENT_SLAVE_ACK_FAILURE))
+/**
+ * @}
+ */
+
+/** @defgroup I2C_own_address1
+ * @{
+ */
+
+#define IS_I2C_OWN_ADDRESS1(ADDRESS1) ((ADDRESS1) <= 0x3FF)
+/**
+ * @}
+ */
+
+/** @defgroup I2C_clock_speed
+ * @{
+ */
+
+#define IS_I2C_CLOCK_SPEED(SPEED) (((SPEED) >= 0x1) && ((SPEED) <= 400000))
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup I2C_Exported_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup I2C_Exported_Functions
+ * @{
+ */
+
+void I2C_DeInit(I2C_TypeDef* I2Cx);
+void I2C_Init(I2C_TypeDef* I2Cx, I2C_InitTypeDef* I2C_InitStruct);
+void I2C_StructInit(I2C_InitTypeDef* I2C_InitStruct);
+void I2C_Cmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_DMACmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_DMALastTransferCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_GenerateSTART(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_GenerateSTOP(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_AcknowledgeConfig(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_OwnAddress2Config(I2C_TypeDef* I2Cx, uint8_t Address);
+void I2C_DualAddressCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_GeneralCallCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_ITConfig(I2C_TypeDef* I2Cx, uint16_t I2C_IT, FunctionalState NewState);
+void I2C_SendData(I2C_TypeDef* I2Cx, uint8_t Data);
+uint8_t I2C_ReceiveData(I2C_TypeDef* I2Cx);
+void I2C_Send7bitAddress(I2C_TypeDef* I2Cx, uint8_t Address, uint8_t I2C_Direction);
+uint16_t I2C_ReadRegister(I2C_TypeDef* I2Cx, uint8_t I2C_Register);
+void I2C_SoftwareResetCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_NACKPositionConfig(I2C_TypeDef* I2Cx, uint16_t I2C_NACKPosition);
+void I2C_SMBusAlertConfig(I2C_TypeDef* I2Cx, uint16_t I2C_SMBusAlert);
+void I2C_TransmitPEC(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_PECPositionConfig(I2C_TypeDef* I2Cx, uint16_t I2C_PECPosition);
+void I2C_CalculatePEC(I2C_TypeDef* I2Cx, FunctionalState NewState);
+uint8_t I2C_GetPEC(I2C_TypeDef* I2Cx);
+void I2C_ARPCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_StretchClockCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
+void I2C_FastModeDutyCycleConfig(I2C_TypeDef* I2Cx, uint16_t I2C_DutyCycle);
+
+/**
+ * @brief
+ ****************************************************************************************
+ *
+ * I2C State Monitoring Functions
+ *
+ ****************************************************************************************
+ * This I2C driver provides three different ways for I2C state monitoring
+ * depending on the application requirements and constraints:
+ *
+ *
+ * 1) Basic state monitoring:
+ * Using I2C_CheckEvent() function:
+ * It compares the status registers (SR1 and SR2) content to a given event
+ * (can be the combination of one or more flags).
+ * It returns SUCCESS if the current status includes the given flags
+ * and returns ERROR if one or more flags are missing in the current status.
+ * - When to use:
+ * - This function is suitable for most applications as well as for startup
+ * activity since the events are fully described in the product reference manual
+ * (RM0008).
+ * - It is also suitable for users who need to define their own events.
+ * - Limitations:
+ * - If an error occurs (ie. error flags are set besides to the monitored flags),
+ * the I2C_CheckEvent() function may return SUCCESS despite the communication
+ * hold or corrupted real state.
+ * In this case, it is advised to use error interrupts to monitor the error
+ * events and handle them in the interrupt IRQ handler.
+ *
+ * @note
+ * For error management, it is advised to use the following functions:
+ * - I2C_ITConfig() to configure and enable the error interrupts (I2C_IT_ERR).
+ * - I2Cx_ER_IRQHandler() which is called when the error interrupt occurs.
+ * Where x is the peripheral instance (I2C1, I2C2 ...)
+ * - I2C_GetFlagStatus() or I2C_GetITStatus() to be called into I2Cx_ER_IRQHandler()
+ * in order to determine which error occurred.
+ * - I2C_ClearFlag() or I2C_ClearITPendingBit() and/or I2C_SoftwareResetCmd()
+ * and/or I2C_GenerateStop() in order to clear the error flag and source,
+ * and return to correct communication status.
+ *
+ *
+ * 2) Advanced state monitoring:
+ * Using the function I2C_GetLastEvent() which returns the image of both status
+ * registers in a single word (uint32_t) (Status Register 2 value is shifted left
+ * by 16 bits and concatenated to Status Register 1).
+ * - When to use:
+ * - This function is suitable for the same applications above but it allows to
+ * overcome the limitations of I2C_GetFlagStatus() function (see below).
+ * The returned value could be compared to events already defined in the
+ * library (stm32f10x_i2c.h) or to custom values defined by user.
+ * - This function is suitable when multiple flags are monitored at the same time.
+ * - At the opposite of I2C_CheckEvent() function, this function allows user to
+ * choose when an event is accepted (when all events flags are set and no
+ * other flags are set or just when the needed flags are set like
+ * I2C_CheckEvent() function).
+ * - Limitations:
+ * - User may need to define his own events.
+ * - Same remark concerning the error management is applicable for this
+ * function if user decides to check only regular communication flags (and
+ * ignores error flags).
+ *
+ *
+ * 3) Flag-based state monitoring:
+ * Using the function I2C_GetFlagStatus() which simply returns the status of
+ * one single flag (ie. I2C_FLAG_RXNE ...).
+ * - When to use:
+ * - This function could be used for specific applications or in debug phase.
+ * - It is suitable when only one flag checking is needed (most I2C events
+ * are monitored through multiple flags).
+ * - Limitations:
+ * - When calling this function, the Status register is accessed. Some flags are
+ * cleared when the status register is accessed. So checking the status
+ * of one Flag, may clear other ones.
+ * - Function may need to be called twice or more in order to monitor one
+ * single event.
+ *
+ */
+
+/**
+ *
+ * 1) Basic state monitoring
+ *******************************************************************************
+ */
+ErrorStatus I2C_CheckEvent(I2C_TypeDef* I2Cx, uint32_t I2C_EVENT);
+/**
+ *
+ * 2) Advanced state monitoring
+ *******************************************************************************
+ */
+uint32_t I2C_GetLastEvent(I2C_TypeDef* I2Cx);
+/**
+ *
+ * 3) Flag-based state monitoring
+ *******************************************************************************
+ */
+FlagStatus I2C_GetFlagStatus(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG);
+/**
+ *
+ *******************************************************************************
+ */
+
+void I2C_ClearFlag(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG);
+ITStatus I2C_GetITStatus(I2C_TypeDef* I2Cx, uint32_t I2C_IT);
+void I2C_ClearITPendingBit(I2C_TypeDef* I2Cx, uint32_t I2C_IT);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /*__STM32F10x_I2C_H */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_iwdg.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_iwdg.h
new file mode 100644
index 00000000..7f5ab764
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/inc/stm32f10x_iwdg.h
@@ -0,0 +1,140 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x_iwdg.h
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief This file contains all the functions prototypes for the IWDG
+ * firmware library.
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_flash.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup FLASH
+ * @brief FLASH driver modules
+ * @{
+ */
+
+/** @defgroup FLASH_Private_TypesDefinitions
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup FLASH_Private_Defines
+ * @{
+ */
+
+/* Flash Access Control Register bits */
+#define ACR_LATENCY_Mask ((uint32_t)0x00000038)
+#define ACR_HLFCYA_Mask ((uint32_t)0xFFFFFFF7)
+#define ACR_PRFTBE_Mask ((uint32_t)0xFFFFFFEF)
+
+/* Flash Access Control Register bits */
+#define ACR_PRFTBS_Mask ((uint32_t)0x00000020)
+
+/* Flash Control Register bits */
+#define CR_PG_Set ((uint32_t)0x00000001)
+#define CR_PG_Reset ((uint32_t)0x00001FFE)
+#define CR_PER_Set ((uint32_t)0x00000002)
+#define CR_PER_Reset ((uint32_t)0x00001FFD)
+#define CR_MER_Set ((uint32_t)0x00000004)
+#define CR_MER_Reset ((uint32_t)0x00001FFB)
+#define CR_OPTPG_Set ((uint32_t)0x00000010)
+#define CR_OPTPG_Reset ((uint32_t)0x00001FEF)
+#define CR_OPTER_Set ((uint32_t)0x00000020)
+#define CR_OPTER_Reset ((uint32_t)0x00001FDF)
+#define CR_STRT_Set ((uint32_t)0x00000040)
+#define CR_LOCK_Set ((uint32_t)0x00000080)
+
+/* FLASH Mask */
+#define RDPRT_Mask ((uint32_t)0x00000002)
+#define WRP0_Mask ((uint32_t)0x000000FF)
+#define WRP1_Mask ((uint32_t)0x0000FF00)
+#define WRP2_Mask ((uint32_t)0x00FF0000)
+#define WRP3_Mask ((uint32_t)0xFF000000)
+#define OB_USER_BFB2 ((uint16_t)0x0008)
+
+/* FLASH Keys */
+#define RDP_Key ((uint16_t)0x00A5)
+#define FLASH_KEY1 ((uint32_t)0x45670123)
+#define FLASH_KEY2 ((uint32_t)0xCDEF89AB)
+
+/* FLASH BANK address */
+#define FLASH_BANK1_END_ADDRESS ((uint32_t)0x807FFFF)
+
+/* Delay definition */
+#define EraseTimeout ((uint32_t)0x000B0000)
+#define ProgramTimeout ((uint32_t)0x00002000)
+/**
+ * @}
+ */
+
+/** @defgroup FLASH_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup FLASH_Private_Variables
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup FLASH_Private_FunctionPrototypes
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup FLASH_Private_Functions
+ * @{
+ */
+
+/**
+@code
+
+ This driver provides functions to configure and program the Flash memory of all STM32F10x devices,
+ including the latest STM32F10x_XL density devices.
+
+ STM32F10x_XL devices feature up to 1 Mbyte with dual bank architecture for read-while-write (RWW) capability:
+ - bank1: fixed size of 512 Kbytes (256 pages of 2Kbytes each)
+ - bank2: up to 512 Kbytes (up to 256 pages of 2Kbytes each)
+ While other STM32F10x devices features only one bank with memory up to 512 Kbytes.
+
+ In version V3.3.0, some functions were updated and new ones were added to support
+ STM32F10x_XL devices. Thus some functions manages all devices, while other are
+ dedicated for XL devices only.
+
+ The table below presents the list of available functions depending on the used STM32F10x devices.
+
+ ***************************************************
+ * Legacy functions used for all STM32F10x devices *
+ ***************************************************
+ +----------------------------------------------------------------------------------------------------------------------------------+
+ | Functions prototypes |STM32F10x_XL|Other STM32F10x| Comments |
+ | | devices | devices | |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_SetLatency | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_HalfCycleAccessCmd | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_PrefetchBufferCmd | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_Unlock | Yes | Yes | - For STM32F10X_XL devices: unlock Bank1 and Bank2. |
+ | | | | - For other devices: unlock Bank1 and it is equivalent |
+ | | | | to FLASH_UnlockBank1 function. |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_Lock | Yes | Yes | - For STM32F10X_XL devices: lock Bank1 and Bank2. |
+ | | | | - For other devices: lock Bank1 and it is equivalent |
+ | | | | to FLASH_LockBank1 function. |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_ErasePage | Yes | Yes | - For STM32F10x_XL devices: erase a page in Bank1 and Bank2 |
+ | | | | - For other devices: erase a page in Bank1 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_EraseAllPages | Yes | Yes | - For STM32F10x_XL devices: erase all pages in Bank1 and Bank2 |
+ | | | | - For other devices: erase all pages in Bank1 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_EraseOptionBytes | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_ProgramWord | Yes | Yes | Updated to program up to 1MByte (depending on the used device) |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_ProgramHalfWord | Yes | Yes | Updated to program up to 1MByte (depending on the used device) |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_ProgramOptionByteData | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_EnableWriteProtection | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_ReadOutProtection | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_UserOptionByteConfig | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_GetUserOptionByte | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_GetWriteProtectionOptionByte | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_GetReadOutProtectionStatus | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_GetPrefetchBufferStatus | Yes | Yes | No change |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_ITConfig | Yes | Yes | - For STM32F10x_XL devices: enable Bank1 and Bank2's interrupts|
+ | | | | - For other devices: enable Bank1's interrupts |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_GetFlagStatus | Yes | Yes | - For STM32F10x_XL devices: return Bank1 and Bank2's flag status|
+ | | | | - For other devices: return Bank1's flag status |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_ClearFlag | Yes | Yes | - For STM32F10x_XL devices: clear Bank1 and Bank2's flag |
+ | | | | - For other devices: clear Bank1's flag |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_GetStatus | Yes | Yes | - Return the status of Bank1 (for all devices) |
+ | | | | equivalent to FLASH_GetBank1Status function |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_WaitForLastOperation | Yes | Yes | - Wait for Bank1 last operation (for all devices) |
+ | | | | equivalent to: FLASH_WaitForLastBank1Operation function |
+ +----------------------------------------------------------------------------------------------------------------------------------+
+
+ ************************************************************************************************************************
+ * New functions used for all STM32F10x devices to manage Bank1: *
+ * - These functions are mainly useful for STM32F10x_XL density devices, to have separate control for Bank1 and bank2 *
+ * - For other devices, these functions are optional (covered by functions listed above) *
+ ************************************************************************************************************************
+ +----------------------------------------------------------------------------------------------------------------------------------+
+ | Functions prototypes |STM32F10x_XL|Other STM32F10x| Comments |
+ | | devices | devices | |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_UnlockBank1 | Yes | Yes | - Unlock Bank1 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_LockBank1 | Yes | Yes | - Lock Bank1 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_EraseAllBank1Pages | Yes | Yes | - Erase all pages in Bank1 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_GetBank1Status | Yes | Yes | - Return the status of Bank1 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_WaitForLastBank1Operation | Yes | Yes | - Wait for Bank1 last operation |
+ +----------------------------------------------------------------------------------------------------------------------------------+
+
+ *****************************************************************************
+ * New Functions used only with STM32F10x_XL density devices to manage Bank2 *
+ *****************************************************************************
+ +----------------------------------------------------------------------------------------------------------------------------------+
+ | Functions prototypes |STM32F10x_XL|Other STM32F10x| Comments |
+ | | devices | devices | |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_UnlockBank2 | Yes | No | - Unlock Bank2 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ |FLASH_LockBank2 | Yes | No | - Lock Bank2 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_EraseAllBank2Pages | Yes | No | - Erase all pages in Bank2 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_GetBank2Status | Yes | No | - Return the status of Bank2 |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_WaitForLastBank2Operation | Yes | No | - Wait for Bank2 last operation |
+ |----------------------------------------------------------------------------------------------------------------------------------|
+ | FLASH_BootConfig | Yes | No | - Configure to boot from Bank1 or Bank2 |
+ +----------------------------------------------------------------------------------------------------------------------------------+
+@endcode
+*/
+
+
+/**
+ * @brief Sets the code latency value.
+ * @note This function can be used for all STM32F10x devices.
+ * @param FLASH_Latency: specifies the FLASH Latency value.
+ * This parameter can be one of the following values:
+ * @arg FLASH_Latency_0: FLASH Zero Latency cycle
+ * @arg FLASH_Latency_1: FLASH One Latency cycle
+ * @arg FLASH_Latency_2: FLASH Two Latency cycles
+ * @retval None
+ */
+void FLASH_SetLatency(uint32_t FLASH_Latency)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_FLASH_LATENCY(FLASH_Latency));
+
+ /* Read the ACR register */
+ tmpreg = FLASH->ACR;
+
+ /* Sets the Latency value */
+ tmpreg &= ACR_LATENCY_Mask;
+ tmpreg |= FLASH_Latency;
+
+ /* Write the ACR register */
+ FLASH->ACR = tmpreg;
+}
+
+/**
+ * @brief Enables or disables the Half cycle flash access.
+ * @note This function can be used for all STM32F10x devices.
+ * @param FLASH_HalfCycleAccess: specifies the FLASH Half cycle Access mode.
+ * This parameter can be one of the following values:
+ * @arg FLASH_HalfCycleAccess_Enable: FLASH Half Cycle Enable
+ * @arg FLASH_HalfCycleAccess_Disable: FLASH Half Cycle Disable
+ * @retval None
+ */
+void FLASH_HalfCycleAccessCmd(uint32_t FLASH_HalfCycleAccess)
+{
+ /* Check the parameters */
+ assert_param(IS_FLASH_HALFCYCLEACCESS_STATE(FLASH_HalfCycleAccess));
+
+ /* Enable or disable the Half cycle access */
+ FLASH->ACR &= ACR_HLFCYA_Mask;
+ FLASH->ACR |= FLASH_HalfCycleAccess;
+}
+
+/**
+ * @brief Enables or disables the Prefetch Buffer.
+ * @note This function can be used for all STM32F10x devices.
+ * @param FLASH_PrefetchBuffer: specifies the Prefetch buffer status.
+ * This parameter can be one of the following values:
+ * @arg FLASH_PrefetchBuffer_Enable: FLASH Prefetch Buffer Enable
+ * @arg FLASH_PrefetchBuffer_Disable: FLASH Prefetch Buffer Disable
+ * @retval None
+ */
+void FLASH_PrefetchBufferCmd(uint32_t FLASH_PrefetchBuffer)
+{
+ /* Check the parameters */
+ assert_param(IS_FLASH_PREFETCHBUFFER_STATE(FLASH_PrefetchBuffer));
+
+ /* Enable or disable the Prefetch Buffer */
+ FLASH->ACR &= ACR_PRFTBE_Mask;
+ FLASH->ACR |= FLASH_PrefetchBuffer;
+}
+
+/**
+ * @brief Unlocks the FLASH Program Erase Controller.
+ * @note This function can be used for all STM32F10x devices.
+ * - For STM32F10X_XL devices this function unlocks Bank1 and Bank2.
+ * - For all other devices it unlocks Bank1 and it is equivalent
+ * to FLASH_UnlockBank1 function..
+ * @param None
+ * @retval None
+ */
+void FLASH_Unlock(void)
+{
+ /* Authorize the FPEC of Bank1 Access */
+ FLASH->KEYR = FLASH_KEY1;
+ FLASH->KEYR = FLASH_KEY2;
+
+#ifdef STM32F10X_XL
+ /* Authorize the FPEC of Bank2 Access */
+ FLASH->KEYR2 = FLASH_KEY1;
+ FLASH->KEYR2 = FLASH_KEY2;
+#endif /* STM32F10X_XL */
+}
+/**
+ * @brief Unlocks the FLASH Bank1 Program Erase Controller.
+ * @note This function can be used for all STM32F10x devices.
+ * - For STM32F10X_XL devices this function unlocks Bank1.
+ * - For all other devices it unlocks Bank1 and it is
+ * equivalent to FLASH_Unlock function.
+ * @param None
+ * @retval None
+ */
+void FLASH_UnlockBank1(void)
+{
+ /* Authorize the FPEC of Bank1 Access */
+ FLASH->KEYR = FLASH_KEY1;
+ FLASH->KEYR = FLASH_KEY2;
+}
+
+#ifdef STM32F10X_XL
+/**
+ * @brief Unlocks the FLASH Bank2 Program Erase Controller.
+ * @note This function can be used only for STM32F10X_XL density devices.
+ * @param None
+ * @retval None
+ */
+void FLASH_UnlockBank2(void)
+{
+ /* Authorize the FPEC of Bank2 Access */
+ FLASH->KEYR2 = FLASH_KEY1;
+ FLASH->KEYR2 = FLASH_KEY2;
+
+}
+#endif /* STM32F10X_XL */
+
+/**
+ * @brief Locks the FLASH Program Erase Controller.
+ * @note This function can be used for all STM32F10x devices.
+ * - For STM32F10X_XL devices this function Locks Bank1 and Bank2.
+ * - For all other devices it Locks Bank1 and it is equivalent
+ * to FLASH_LockBank1 function.
+ * @param None
+ * @retval None
+ */
+void FLASH_Lock(void)
+{
+ /* Set the Lock Bit to lock the FPEC and the CR of Bank1 */
+ FLASH->CR |= CR_LOCK_Set;
+
+#ifdef STM32F10X_XL
+ /* Set the Lock Bit to lock the FPEC and the CR of Bank2 */
+ FLASH->CR2 |= CR_LOCK_Set;
+#endif /* STM32F10X_XL */
+}
+
+/**
+ * @brief Locks the FLASH Bank1 Program Erase Controller.
+ * @note this function can be used for all STM32F10x devices.
+ * - For STM32F10X_XL devices this function Locks Bank1.
+ * - For all other devices it Locks Bank1 and it is equivalent
+ * to FLASH_Lock function.
+ * @param None
+ * @retval None
+ */
+void FLASH_LockBank1(void)
+{
+ /* Set the Lock Bit to lock the FPEC and the CR of Bank1 */
+ FLASH->CR |= CR_LOCK_Set;
+}
+
+#ifdef STM32F10X_XL
+/**
+ * @brief Locks the FLASH Bank2 Program Erase Controller.
+ * @note This function can be used only for STM32F10X_XL density devices.
+ * @param None
+ * @retval None
+ */
+void FLASH_LockBank2(void)
+{
+ /* Set the Lock Bit to lock the FPEC and the CR of Bank2 */
+ FLASH->CR2 |= CR_LOCK_Set;
+}
+#endif /* STM32F10X_XL */
+
+/**
+ * @brief Erases a specified FLASH page.
+ * @note This function can be used for all STM32F10x devices.
+ * @param Page_Address: The page address to be erased.
+ * @retval FLASH Status: The returned value can be: FLASH_BUSY, FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_ErasePage(uint32_t Page_Address)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+ /* Check the parameters */
+ assert_param(IS_FLASH_ADDRESS(Page_Address));
+
+#ifdef STM32F10X_XL
+ if(Page_Address < FLASH_BANK1_END_ADDRESS)
+ {
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(EraseTimeout);
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to erase the page */
+ FLASH->CR|= CR_PER_Set;
+ FLASH->AR = Page_Address;
+ FLASH->CR|= CR_STRT_Set;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(EraseTimeout);
+
+ /* Disable the PER Bit */
+ FLASH->CR &= CR_PER_Reset;
+ }
+ }
+ else
+ {
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(EraseTimeout);
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to erase the page */
+ FLASH->CR2|= CR_PER_Set;
+ FLASH->AR2 = Page_Address;
+ FLASH->CR2|= CR_STRT_Set;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(EraseTimeout);
+
+ /* Disable the PER Bit */
+ FLASH->CR2 &= CR_PER_Reset;
+ }
+ }
+#else
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to erase the page */
+ FLASH->CR|= CR_PER_Set;
+ FLASH->AR = Page_Address;
+ FLASH->CR|= CR_STRT_Set;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+
+ /* Disable the PER Bit */
+ FLASH->CR &= CR_PER_Reset;
+ }
+#endif /* STM32F10X_XL */
+
+ /* Return the Erase Status */
+ return status;
+}
+
+/**
+ * @brief Erases all FLASH pages.
+ * @note This function can be used for all STM32F10x devices.
+ * @param None
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_EraseAllPages(void)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+
+#ifdef STM32F10X_XL
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(EraseTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to erase all pages */
+ FLASH->CR |= CR_MER_Set;
+ FLASH->CR |= CR_STRT_Set;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(EraseTimeout);
+
+ /* Disable the MER Bit */
+ FLASH->CR &= CR_MER_Reset;
+ }
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to erase all pages */
+ FLASH->CR2 |= CR_MER_Set;
+ FLASH->CR2 |= CR_STRT_Set;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(EraseTimeout);
+
+ /* Disable the MER Bit */
+ FLASH->CR2 &= CR_MER_Reset;
+ }
+#else
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to erase all pages */
+ FLASH->CR |= CR_MER_Set;
+ FLASH->CR |= CR_STRT_Set;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+
+ /* Disable the MER Bit */
+ FLASH->CR &= CR_MER_Reset;
+ }
+#endif /* STM32F10X_XL */
+
+ /* Return the Erase Status */
+ return status;
+}
+
+/**
+ * @brief Erases all Bank1 FLASH pages.
+ * @note This function can be used for all STM32F10x devices.
+ * - For STM32F10X_XL devices this function erases all Bank1 pages.
+ * - For all other devices it erases all Bank1 pages and it is equivalent
+ * to FLASH_EraseAllPages function.
+ * @param None
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_EraseAllBank1Pages(void)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(EraseTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to erase all pages */
+ FLASH->CR |= CR_MER_Set;
+ FLASH->CR |= CR_STRT_Set;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(EraseTimeout);
+
+ /* Disable the MER Bit */
+ FLASH->CR &= CR_MER_Reset;
+ }
+ /* Return the Erase Status */
+ return status;
+}
+
+#ifdef STM32F10X_XL
+/**
+ * @brief Erases all Bank2 FLASH pages.
+ * @note This function can be used only for STM32F10x_XL density devices.
+ * @param None
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_EraseAllBank2Pages(void)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(EraseTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to erase all pages */
+ FLASH->CR2 |= CR_MER_Set;
+ FLASH->CR2 |= CR_STRT_Set;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(EraseTimeout);
+
+ /* Disable the MER Bit */
+ FLASH->CR2 &= CR_MER_Reset;
+ }
+ /* Return the Erase Status */
+ return status;
+}
+#endif /* STM32F10X_XL */
+
+/**
+ * @brief Erases the FLASH option bytes.
+ * @note This functions erases all option bytes except the Read protection (RDP).
+ * @note This function can be used for all STM32F10x devices.
+ * @param None
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_EraseOptionBytes(void)
+{
+ uint16_t rdptmp = RDP_Key;
+
+ FLASH_Status status = FLASH_COMPLETE;
+
+ /* Get the actual read protection Option Byte value */
+ if(FLASH_GetReadOutProtectionStatus() != RESET)
+ {
+ rdptmp = 0x00;
+ }
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+ if(status == FLASH_COMPLETE)
+ {
+ /* Authorize the small information block programming */
+ FLASH->OPTKEYR = FLASH_KEY1;
+ FLASH->OPTKEYR = FLASH_KEY2;
+
+ /* if the previous operation is completed, proceed to erase the option bytes */
+ FLASH->CR |= CR_OPTER_Set;
+ FLASH->CR |= CR_STRT_Set;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the erase operation is completed, disable the OPTER Bit */
+ FLASH->CR &= CR_OPTER_Reset;
+
+ /* Enable the Option Bytes Programming operation */
+ FLASH->CR |= CR_OPTPG_Set;
+ /* Restore the last read protection Option Byte value */
+ OB->RDP = (uint16_t)rdptmp;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status != FLASH_TIMEOUT)
+ {
+ /* if the program operation is completed, disable the OPTPG Bit */
+ FLASH->CR &= CR_OPTPG_Reset;
+ }
+ }
+ else
+ {
+ if (status != FLASH_TIMEOUT)
+ {
+ /* Disable the OPTPG Bit */
+ FLASH->CR &= CR_OPTPG_Reset;
+ }
+ }
+ }
+ /* Return the erase status */
+ return status;
+}
+
+/**
+ * @brief Programs a word at a specified address.
+ * @note This function can be used for all STM32F10x devices.
+ * @param Address: specifies the address to be programmed.
+ * @param Data: specifies the data to be programmed.
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_ProgramWord(uint32_t Address, uint32_t Data)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+ __IO uint32_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_FLASH_ADDRESS(Address));
+
+#ifdef STM32F10X_XL
+ if(Address < FLASH_BANK1_END_ADDRESS - 2)
+ {
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(ProgramTimeout);
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new first
+ half word */
+ FLASH->CR |= CR_PG_Set;
+
+ *(__IO uint16_t*)Address = (uint16_t)Data;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new second
+ half word */
+ tmp = Address + 2;
+
+ *(__IO uint16_t*) tmp = Data >> 16;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ /* Disable the PG Bit */
+ FLASH->CR &= CR_PG_Reset;
+ }
+ else
+ {
+ /* Disable the PG Bit */
+ FLASH->CR &= CR_PG_Reset;
+ }
+ }
+ }
+ else if(Address == (FLASH_BANK1_END_ADDRESS - 1))
+ {
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new first
+ half word */
+ FLASH->CR |= CR_PG_Set;
+
+ *(__IO uint16_t*)Address = (uint16_t)Data;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(ProgramTimeout);
+
+ /* Disable the PG Bit */
+ FLASH->CR &= CR_PG_Reset;
+ }
+ else
+ {
+ /* Disable the PG Bit */
+ FLASH->CR &= CR_PG_Reset;
+ }
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new second
+ half word */
+ FLASH->CR2 |= CR_PG_Set;
+ tmp = Address + 2;
+
+ *(__IO uint16_t*) tmp = Data >> 16;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(ProgramTimeout);
+
+ /* Disable the PG Bit */
+ FLASH->CR2 &= CR_PG_Reset;
+ }
+ else
+ {
+ /* Disable the PG Bit */
+ FLASH->CR2 &= CR_PG_Reset;
+ }
+ }
+ else
+ {
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new first
+ half word */
+ FLASH->CR2 |= CR_PG_Set;
+
+ *(__IO uint16_t*)Address = (uint16_t)Data;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new second
+ half word */
+ tmp = Address + 2;
+
+ *(__IO uint16_t*) tmp = Data >> 16;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(ProgramTimeout);
+
+ /* Disable the PG Bit */
+ FLASH->CR2 &= CR_PG_Reset;
+ }
+ else
+ {
+ /* Disable the PG Bit */
+ FLASH->CR2 &= CR_PG_Reset;
+ }
+ }
+ }
+#else
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new first
+ half word */
+ FLASH->CR |= CR_PG_Set;
+
+ *(__IO uint16_t*)Address = (uint16_t)Data;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new second
+ half word */
+ tmp = Address + 2;
+
+ *(__IO uint16_t*) tmp = Data >> 16;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ /* Disable the PG Bit */
+ FLASH->CR &= CR_PG_Reset;
+ }
+ else
+ {
+ /* Disable the PG Bit */
+ FLASH->CR &= CR_PG_Reset;
+ }
+ }
+#endif /* STM32F10X_XL */
+
+ /* Return the Program Status */
+ return status;
+}
+
+/**
+ * @brief Programs a half word at a specified address.
+ * @note This function can be used for all STM32F10x devices.
+ * @param Address: specifies the address to be programmed.
+ * @param Data: specifies the data to be programmed.
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_ProgramHalfWord(uint32_t Address, uint16_t Data)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+ /* Check the parameters */
+ assert_param(IS_FLASH_ADDRESS(Address));
+
+#ifdef STM32F10X_XL
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(Address < FLASH_BANK1_END_ADDRESS)
+ {
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new data */
+ FLASH->CR |= CR_PG_Set;
+
+ *(__IO uint16_t*)Address = Data;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank1Operation(ProgramTimeout);
+
+ /* Disable the PG Bit */
+ FLASH->CR &= CR_PG_Reset;
+ }
+ }
+ else
+ {
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new data */
+ FLASH->CR2 |= CR_PG_Set;
+
+ *(__IO uint16_t*)Address = Data;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastBank2Operation(ProgramTimeout);
+
+ /* Disable the PG Bit */
+ FLASH->CR2 &= CR_PG_Reset;
+ }
+ }
+#else
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the previous operation is completed, proceed to program the new data */
+ FLASH->CR |= CR_PG_Set;
+
+ *(__IO uint16_t*)Address = Data;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ /* Disable the PG Bit */
+ FLASH->CR &= CR_PG_Reset;
+ }
+#endif /* STM32F10X_XL */
+
+ /* Return the Program Status */
+ return status;
+}
+
+/**
+ * @brief Programs a half word at a specified Option Byte Data address.
+ * @note This function can be used for all STM32F10x devices.
+ * @param Address: specifies the address to be programmed.
+ * This parameter can be 0x1FFFF804 or 0x1FFFF806.
+ * @param Data: specifies the data to be programmed.
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_ProgramOptionByteData(uint32_t Address, uint8_t Data)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+ /* Check the parameters */
+ assert_param(IS_OB_DATA_ADDRESS(Address));
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* Authorize the small information block programming */
+ FLASH->OPTKEYR = FLASH_KEY1;
+ FLASH->OPTKEYR = FLASH_KEY2;
+ /* Enables the Option Bytes Programming operation */
+ FLASH->CR |= CR_OPTPG_Set;
+ *(__IO uint16_t*)Address = Data;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+ if(status != FLASH_TIMEOUT)
+ {
+ /* if the program operation is completed, disable the OPTPG Bit */
+ FLASH->CR &= CR_OPTPG_Reset;
+ }
+ }
+ /* Return the Option Byte Data Program Status */
+ return status;
+}
+
+/**
+ * @brief Write protects the desired pages
+ * @note This function can be used for all STM32F10x devices.
+ * @param FLASH_Pages: specifies the address of the pages to be write protected.
+ * This parameter can be:
+ * @arg For @b STM32_Low-density_devices: value between FLASH_WRProt_Pages0to3 and FLASH_WRProt_Pages28to31
+ * @arg For @b STM32_Medium-density_devices: value between FLASH_WRProt_Pages0to3
+ * and FLASH_WRProt_Pages124to127
+ * @arg For @b STM32_High-density_devices: value between FLASH_WRProt_Pages0to1 and
+ * FLASH_WRProt_Pages60to61 or FLASH_WRProt_Pages62to255
+ * @arg For @b STM32_Connectivity_line_devices: value between FLASH_WRProt_Pages0to1 and
+ * FLASH_WRProt_Pages60to61 or FLASH_WRProt_Pages62to127
+ * @arg For @b STM32_XL-density_devices: value between FLASH_WRProt_Pages0to1 and
+ * FLASH_WRProt_Pages60to61 or FLASH_WRProt_Pages62to511
+ * @arg FLASH_WRProt_AllPages
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_EnableWriteProtection(uint32_t FLASH_Pages)
+{
+ uint16_t WRP0_Data = 0xFFFF, WRP1_Data = 0xFFFF, WRP2_Data = 0xFFFF, WRP3_Data = 0xFFFF;
+
+ FLASH_Status status = FLASH_COMPLETE;
+
+ /* Check the parameters */
+ assert_param(IS_FLASH_WRPROT_PAGE(FLASH_Pages));
+
+ FLASH_Pages = (uint32_t)(~FLASH_Pages);
+ WRP0_Data = (uint16_t)(FLASH_Pages & WRP0_Mask);
+ WRP1_Data = (uint16_t)((FLASH_Pages & WRP1_Mask) >> 8);
+ WRP2_Data = (uint16_t)((FLASH_Pages & WRP2_Mask) >> 16);
+ WRP3_Data = (uint16_t)((FLASH_Pages & WRP3_Mask) >> 24);
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* Authorizes the small information block programming */
+ FLASH->OPTKEYR = FLASH_KEY1;
+ FLASH->OPTKEYR = FLASH_KEY2;
+ FLASH->CR |= CR_OPTPG_Set;
+ if(WRP0_Data != 0xFF)
+ {
+ OB->WRP0 = WRP0_Data;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+ }
+ if((status == FLASH_COMPLETE) && (WRP1_Data != 0xFF))
+ {
+ OB->WRP1 = WRP1_Data;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+ }
+ if((status == FLASH_COMPLETE) && (WRP2_Data != 0xFF))
+ {
+ OB->WRP2 = WRP2_Data;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+ }
+
+ if((status == FLASH_COMPLETE)&& (WRP3_Data != 0xFF))
+ {
+ OB->WRP3 = WRP3_Data;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+ }
+
+ if(status != FLASH_TIMEOUT)
+ {
+ /* if the program operation is completed, disable the OPTPG Bit */
+ FLASH->CR &= CR_OPTPG_Reset;
+ }
+ }
+ /* Return the write protection operation Status */
+ return status;
+}
+
+/**
+ * @brief Enables or disables the read out protection.
+ * @note If the user has already programmed the other option bytes before calling
+ * this function, he must re-program them since this function erases all option bytes.
+ * @note This function can be used for all STM32F10x devices.
+ * @param Newstate: new state of the ReadOut Protection.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_ReadOutProtection(FunctionalState NewState)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+ if(status == FLASH_COMPLETE)
+ {
+ /* Authorizes the small information block programming */
+ FLASH->OPTKEYR = FLASH_KEY1;
+ FLASH->OPTKEYR = FLASH_KEY2;
+ FLASH->CR |= CR_OPTER_Set;
+ FLASH->CR |= CR_STRT_Set;
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+ if(status == FLASH_COMPLETE)
+ {
+ /* if the erase operation is completed, disable the OPTER Bit */
+ FLASH->CR &= CR_OPTER_Reset;
+ /* Enable the Option Bytes Programming operation */
+ FLASH->CR |= CR_OPTPG_Set;
+ if(NewState != DISABLE)
+ {
+ OB->RDP = 0x00;
+ }
+ else
+ {
+ OB->RDP = RDP_Key;
+ }
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(EraseTimeout);
+
+ if(status != FLASH_TIMEOUT)
+ {
+ /* if the program operation is completed, disable the OPTPG Bit */
+ FLASH->CR &= CR_OPTPG_Reset;
+ }
+ }
+ else
+ {
+ if(status != FLASH_TIMEOUT)
+ {
+ /* Disable the OPTER Bit */
+ FLASH->CR &= CR_OPTER_Reset;
+ }
+ }
+ }
+ /* Return the protection operation Status */
+ return status;
+}
+
+/**
+ * @brief Programs the FLASH User Option Byte: IWDG_SW / RST_STOP / RST_STDBY.
+ * @note This function can be used for all STM32F10x devices.
+ * @param OB_IWDG: Selects the IWDG mode
+ * This parameter can be one of the following values:
+ * @arg OB_IWDG_SW: Software IWDG selected
+ * @arg OB_IWDG_HW: Hardware IWDG selected
+ * @param OB_STOP: Reset event when entering STOP mode.
+ * This parameter can be one of the following values:
+ * @arg OB_STOP_NoRST: No reset generated when entering in STOP
+ * @arg OB_STOP_RST: Reset generated when entering in STOP
+ * @param OB_STDBY: Reset event when entering Standby mode.
+ * This parameter can be one of the following values:
+ * @arg OB_STDBY_NoRST: No reset generated when entering in STANDBY
+ * @arg OB_STDBY_RST: Reset generated when entering in STANDBY
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_UserOptionByteConfig(uint16_t OB_IWDG, uint16_t OB_STOP, uint16_t OB_STDBY)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+
+ /* Check the parameters */
+ assert_param(IS_OB_IWDG_SOURCE(OB_IWDG));
+ assert_param(IS_OB_STOP_SOURCE(OB_STOP));
+ assert_param(IS_OB_STDBY_SOURCE(OB_STDBY));
+
+ /* Authorize the small information block programming */
+ FLASH->OPTKEYR = FLASH_KEY1;
+ FLASH->OPTKEYR = FLASH_KEY2;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* Enable the Option Bytes Programming operation */
+ FLASH->CR |= CR_OPTPG_Set;
+
+ OB->USER = OB_IWDG | (uint16_t)(OB_STOP | (uint16_t)(OB_STDBY | ((uint16_t)0xF8)));
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+ if(status != FLASH_TIMEOUT)
+ {
+ /* if the program operation is completed, disable the OPTPG Bit */
+ FLASH->CR &= CR_OPTPG_Reset;
+ }
+ }
+ /* Return the Option Byte program Status */
+ return status;
+}
+
+#ifdef STM32F10X_XL
+/**
+ * @brief Configures to boot from Bank1 or Bank2.
+ * @note This function can be used only for STM32F10x_XL density devices.
+ * @param FLASH_BOOT: select the FLASH Bank to boot from.
+ * This parameter can be one of the following values:
+ * @arg FLASH_BOOT_Bank1: At startup, if boot pins are set in boot from user Flash
+ * position and this parameter is selected the device will boot from Bank1(Default).
+ * @arg FLASH_BOOT_Bank2: At startup, if boot pins are set in boot from user Flash
+ * position and this parameter is selected the device will boot from Bank2 or Bank1,
+ * depending on the activation of the bank. The active banks are checked in
+ * the following order: Bank2, followed by Bank1.
+ * The active bank is recognized by the value programmed at the base address
+ * of the respective bank (corresponding to the initial stack pointer value
+ * in the interrupt vector table).
+ * For more information, please refer to AN2606 from www.st.com.
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_BootConfig(uint16_t FLASH_BOOT)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+ assert_param(IS_FLASH_BOOT(FLASH_BOOT));
+ /* Authorize the small information block programming */
+ FLASH->OPTKEYR = FLASH_KEY1;
+ FLASH->OPTKEYR = FLASH_KEY2;
+
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+
+ if(status == FLASH_COMPLETE)
+ {
+ /* Enable the Option Bytes Programming operation */
+ FLASH->CR |= CR_OPTPG_Set;
+
+ if(FLASH_BOOT == FLASH_BOOT_Bank1)
+ {
+ OB->USER |= OB_USER_BFB2;
+ }
+ else
+ {
+ OB->USER &= (uint16_t)(~(uint16_t)(OB_USER_BFB2));
+ }
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation(ProgramTimeout);
+ if(status != FLASH_TIMEOUT)
+ {
+ /* if the program operation is completed, disable the OPTPG Bit */
+ FLASH->CR &= CR_OPTPG_Reset;
+ }
+ }
+ /* Return the Option Byte program Status */
+ return status;
+}
+#endif /* STM32F10X_XL */
+
+/**
+ * @brief Returns the FLASH User Option Bytes values.
+ * @note This function can be used for all STM32F10x devices.
+ * @param None
+ * @retval The FLASH User Option Bytes values:IWDG_SW(Bit0), RST_STOP(Bit1)
+ * and RST_STDBY(Bit2).
+ */
+uint32_t FLASH_GetUserOptionByte(void)
+{
+ /* Return the User Option Byte */
+ return (uint32_t)(FLASH->OBR >> 2);
+}
+
+/**
+ * @brief Returns the FLASH Write Protection Option Bytes Register value.
+ * @note This function can be used for all STM32F10x devices.
+ * @param None
+ * @retval The FLASH Write Protection Option Bytes Register value
+ */
+uint32_t FLASH_GetWriteProtectionOptionByte(void)
+{
+ /* Return the Flash write protection Register value */
+ return (uint32_t)(FLASH->WRPR);
+}
+
+/**
+ * @brief Checks whether the FLASH Read Out Protection Status is set or not.
+ * @note This function can be used for all STM32F10x devices.
+ * @param None
+ * @retval FLASH ReadOut Protection Status(SET or RESET)
+ */
+FlagStatus FLASH_GetReadOutProtectionStatus(void)
+{
+ FlagStatus readoutstatus = RESET;
+ if ((FLASH->OBR & RDPRT_Mask) != (uint32_t)RESET)
+ {
+ readoutstatus = SET;
+ }
+ else
+ {
+ readoutstatus = RESET;
+ }
+ return readoutstatus;
+}
+
+/**
+ * @brief Checks whether the FLASH Prefetch Buffer status is set or not.
+ * @note This function can be used for all STM32F10x devices.
+ * @param None
+ * @retval FLASH Prefetch Buffer Status (SET or RESET).
+ */
+FlagStatus FLASH_GetPrefetchBufferStatus(void)
+{
+ FlagStatus bitstatus = RESET;
+
+ if ((FLASH->ACR & ACR_PRFTBS_Mask) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ /* Return the new state of FLASH Prefetch Buffer Status (SET or RESET) */
+ return bitstatus;
+}
+
+/**
+ * @brief Enables or disables the specified FLASH interrupts.
+ * @note This function can be used for all STM32F10x devices.
+ * - For STM32F10X_XL devices, enables or disables the specified FLASH interrupts
+ for Bank1 and Bank2.
+ * - For other devices it enables or disables the specified FLASH interrupts for Bank1.
+ * @param FLASH_IT: specifies the FLASH interrupt sources to be enabled or disabled.
+ * This parameter can be any combination of the following values:
+ * @arg FLASH_IT_ERROR: FLASH Error Interrupt
+ * @arg FLASH_IT_EOP: FLASH end of operation Interrupt
+ * @param NewState: new state of the specified Flash interrupts.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void FLASH_ITConfig(uint32_t FLASH_IT, FunctionalState NewState)
+{
+#ifdef STM32F10X_XL
+ /* Check the parameters */
+ assert_param(IS_FLASH_IT(FLASH_IT));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if((FLASH_IT & 0x80000000) != 0x0)
+ {
+ if(NewState != DISABLE)
+ {
+ /* Enable the interrupt sources */
+ FLASH->CR2 |= (FLASH_IT & 0x7FFFFFFF);
+ }
+ else
+ {
+ /* Disable the interrupt sources */
+ FLASH->CR2 &= ~(uint32_t)(FLASH_IT & 0x7FFFFFFF);
+ }
+ }
+ else
+ {
+ if(NewState != DISABLE)
+ {
+ /* Enable the interrupt sources */
+ FLASH->CR |= FLASH_IT;
+ }
+ else
+ {
+ /* Disable the interrupt sources */
+ FLASH->CR &= ~(uint32_t)FLASH_IT;
+ }
+ }
+#else
+ /* Check the parameters */
+ assert_param(IS_FLASH_IT(FLASH_IT));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if(NewState != DISABLE)
+ {
+ /* Enable the interrupt sources */
+ FLASH->CR |= FLASH_IT;
+ }
+ else
+ {
+ /* Disable the interrupt sources */
+ FLASH->CR &= ~(uint32_t)FLASH_IT;
+ }
+#endif /* STM32F10X_XL */
+}
+
+/**
+ * @brief Checks whether the specified FLASH flag is set or not.
+ * @note This function can be used for all STM32F10x devices.
+ * - For STM32F10X_XL devices, this function checks whether the specified
+ * Bank1 or Bank2 flag is set or not.
+ * - For other devices, it checks whether the specified Bank1 flag is
+ * set or not.
+ * @param FLASH_FLAG: specifies the FLASH flag to check.
+ * This parameter can be one of the following values:
+ * @arg FLASH_FLAG_BSY: FLASH Busy flag
+ * @arg FLASH_FLAG_PGERR: FLASH Program error flag
+ * @arg FLASH_FLAG_WRPRTERR: FLASH Write protected error flag
+ * @arg FLASH_FLAG_EOP: FLASH End of Operation flag
+ * @arg FLASH_FLAG_OPTERR: FLASH Option Byte error flag
+ * @retval The new state of FLASH_FLAG (SET or RESET).
+ */
+FlagStatus FLASH_GetFlagStatus(uint32_t FLASH_FLAG)
+{
+ FlagStatus bitstatus = RESET;
+
+#ifdef STM32F10X_XL
+ /* Check the parameters */
+ assert_param(IS_FLASH_GET_FLAG(FLASH_FLAG)) ;
+ if(FLASH_FLAG == FLASH_FLAG_OPTERR)
+ {
+ if((FLASH->OBR & FLASH_FLAG_OPTERR) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ }
+ else
+ {
+ if((FLASH_FLAG & 0x80000000) != 0x0)
+ {
+ if((FLASH->SR2 & FLASH_FLAG) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ }
+ else
+ {
+ if((FLASH->SR & FLASH_FLAG) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ }
+ }
+#else
+ /* Check the parameters */
+ assert_param(IS_FLASH_GET_FLAG(FLASH_FLAG)) ;
+ if(FLASH_FLAG == FLASH_FLAG_OPTERR)
+ {
+ if((FLASH->OBR & FLASH_FLAG_OPTERR) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ }
+ else
+ {
+ if((FLASH->SR & FLASH_FLAG) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ }
+#endif /* STM32F10X_XL */
+
+ /* Return the new state of FLASH_FLAG (SET or RESET) */
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the FLASH's pending flags.
+ * @note This function can be used for all STM32F10x devices.
+ * - For STM32F10X_XL devices, this function clears Bank1 or Bank2’s pending flags
+ * - For other devices, it clears Bank1’s pending flags.
+ * @param FLASH_FLAG: specifies the FLASH flags to clear.
+ * This parameter can be any combination of the following values:
+ * @arg FLASH_FLAG_PGERR: FLASH Program error flag
+ * @arg FLASH_FLAG_WRPRTERR: FLASH Write protected error flag
+ * @arg FLASH_FLAG_EOP: FLASH End of Operation flag
+ * @retval None
+ */
+void FLASH_ClearFlag(uint32_t FLASH_FLAG)
+{
+#ifdef STM32F10X_XL
+ /* Check the parameters */
+ assert_param(IS_FLASH_CLEAR_FLAG(FLASH_FLAG)) ;
+
+ if((FLASH_FLAG & 0x80000000) != 0x0)
+ {
+ /* Clear the flags */
+ FLASH->SR2 = FLASH_FLAG;
+ }
+ else
+ {
+ /* Clear the flags */
+ FLASH->SR = FLASH_FLAG;
+ }
+
+#else
+ /* Check the parameters */
+ assert_param(IS_FLASH_CLEAR_FLAG(FLASH_FLAG)) ;
+
+ /* Clear the flags */
+ FLASH->SR = FLASH_FLAG;
+#endif /* STM32F10X_XL */
+}
+
+/**
+ * @brief Returns the FLASH Status.
+ * @note This function can be used for all STM32F10x devices, it is equivalent
+ * to FLASH_GetBank1Status function.
+ * @param None
+ * @retval FLASH Status: The returned value can be: FLASH_BUSY, FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP or FLASH_COMPLETE
+ */
+FLASH_Status FLASH_GetStatus(void)
+{
+ FLASH_Status flashstatus = FLASH_COMPLETE;
+
+ if((FLASH->SR & FLASH_FLAG_BSY) == FLASH_FLAG_BSY)
+ {
+ flashstatus = FLASH_BUSY;
+ }
+ else
+ {
+ if((FLASH->SR & FLASH_FLAG_PGERR) != 0)
+ {
+ flashstatus = FLASH_ERROR_PG;
+ }
+ else
+ {
+ if((FLASH->SR & FLASH_FLAG_WRPRTERR) != 0 )
+ {
+ flashstatus = FLASH_ERROR_WRP;
+ }
+ else
+ {
+ flashstatus = FLASH_COMPLETE;
+ }
+ }
+ }
+ /* Return the Flash Status */
+ return flashstatus;
+}
+
+/**
+ * @brief Returns the FLASH Bank1 Status.
+ * @note This function can be used for all STM32F10x devices, it is equivalent
+ * to FLASH_GetStatus function.
+ * @param None
+ * @retval FLASH Status: The returned value can be: FLASH_BUSY, FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP or FLASH_COMPLETE
+ */
+FLASH_Status FLASH_GetBank1Status(void)
+{
+ FLASH_Status flashstatus = FLASH_COMPLETE;
+
+ if((FLASH->SR & FLASH_FLAG_BANK1_BSY) == FLASH_FLAG_BSY)
+ {
+ flashstatus = FLASH_BUSY;
+ }
+ else
+ {
+ if((FLASH->SR & FLASH_FLAG_BANK1_PGERR) != 0)
+ {
+ flashstatus = FLASH_ERROR_PG;
+ }
+ else
+ {
+ if((FLASH->SR & FLASH_FLAG_BANK1_WRPRTERR) != 0 )
+ {
+ flashstatus = FLASH_ERROR_WRP;
+ }
+ else
+ {
+ flashstatus = FLASH_COMPLETE;
+ }
+ }
+ }
+ /* Return the Flash Status */
+ return flashstatus;
+}
+
+#ifdef STM32F10X_XL
+/**
+ * @brief Returns the FLASH Bank2 Status.
+ * @note This function can be used for STM32F10x_XL density devices.
+ * @param None
+ * @retval FLASH Status: The returned value can be: FLASH_BUSY, FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP or FLASH_COMPLETE
+ */
+FLASH_Status FLASH_GetBank2Status(void)
+{
+ FLASH_Status flashstatus = FLASH_COMPLETE;
+
+ if((FLASH->SR2 & (FLASH_FLAG_BANK2_BSY & 0x7FFFFFFF)) == (FLASH_FLAG_BANK2_BSY & 0x7FFFFFFF))
+ {
+ flashstatus = FLASH_BUSY;
+ }
+ else
+ {
+ if((FLASH->SR2 & (FLASH_FLAG_BANK2_PGERR & 0x7FFFFFFF)) != 0)
+ {
+ flashstatus = FLASH_ERROR_PG;
+ }
+ else
+ {
+ if((FLASH->SR2 & (FLASH_FLAG_BANK2_WRPRTERR & 0x7FFFFFFF)) != 0 )
+ {
+ flashstatus = FLASH_ERROR_WRP;
+ }
+ else
+ {
+ flashstatus = FLASH_COMPLETE;
+ }
+ }
+ }
+ /* Return the Flash Status */
+ return flashstatus;
+}
+#endif /* STM32F10X_XL */
+/**
+ * @brief Waits for a Flash operation to complete or a TIMEOUT to occur.
+ * @note This function can be used for all STM32F10x devices,
+ * it is equivalent to FLASH_WaitForLastBank1Operation.
+ * - For STM32F10X_XL devices this function waits for a Bank1 Flash operation
+ * to complete or a TIMEOUT to occur.
+ * - For all other devices it waits for a Flash operation to complete
+ * or a TIMEOUT to occur.
+ * @param Timeout: FLASH programming Timeout
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_WaitForLastOperation(uint32_t Timeout)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+
+ /* Check for the Flash Status */
+ status = FLASH_GetBank1Status();
+ /* Wait for a Flash operation to complete or a TIMEOUT to occur */
+ while((status == FLASH_BUSY) && (Timeout != 0x00))
+ {
+ status = FLASH_GetBank1Status();
+ Timeout--;
+ }
+ if(Timeout == 0x00 )
+ {
+ status = FLASH_TIMEOUT;
+ }
+ /* Return the operation status */
+ return status;
+}
+
+/**
+ * @brief Waits for a Flash operation on Bank1 to complete or a TIMEOUT to occur.
+ * @note This function can be used for all STM32F10x devices,
+ * it is equivalent to FLASH_WaitForLastOperation.
+ * @param Timeout: FLASH programming Timeout
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_WaitForLastBank1Operation(uint32_t Timeout)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+
+ /* Check for the Flash Status */
+ status = FLASH_GetBank1Status();
+ /* Wait for a Flash operation to complete or a TIMEOUT to occur */
+ while((status == FLASH_FLAG_BANK1_BSY) && (Timeout != 0x00))
+ {
+ status = FLASH_GetBank1Status();
+ Timeout--;
+ }
+ if(Timeout == 0x00 )
+ {
+ status = FLASH_TIMEOUT;
+ }
+ /* Return the operation status */
+ return status;
+}
+
+#ifdef STM32F10X_XL
+/**
+ * @brief Waits for a Flash operation on Bank2 to complete or a TIMEOUT to occur.
+ * @note This function can be used only for STM32F10x_XL density devices.
+ * @param Timeout: FLASH programming Timeout
+ * @retval FLASH Status: The returned value can be: FLASH_ERROR_PG,
+ * FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT.
+ */
+FLASH_Status FLASH_WaitForLastBank2Operation(uint32_t Timeout)
+{
+ FLASH_Status status = FLASH_COMPLETE;
+
+ /* Check for the Flash Status */
+ status = FLASH_GetBank2Status();
+ /* Wait for a Flash operation to complete or a TIMEOUT to occur */
+ while((status == (FLASH_FLAG_BANK2_BSY & 0x7FFFFFFF)) && (Timeout != 0x00))
+ {
+ status = FLASH_GetBank2Status();
+ Timeout--;
+ }
+ if(Timeout == 0x00 )
+ {
+ status = FLASH_TIMEOUT;
+ }
+ /* Return the operation status */
+ return status;
+}
+#endif /* STM32F10X_XL */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_fsmc.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_fsmc.c
new file mode 100644
index 00000000..c75137ca
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_fsmc.c
@@ -0,0 +1,866 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x_fsmc.c
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief This file provides all the FSMC firmware functions.
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_i2c.h"
+#include "stm32f10x_rcc.h"
+
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup I2C
+ * @brief I2C driver modules
+ * @{
+ */
+
+/** @defgroup I2C_Private_TypesDefinitions
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup I2C_Private_Defines
+ * @{
+ */
+
+/* I2C SPE mask */
+#define CR1_PE_Set ((uint16_t)0x0001)
+#define CR1_PE_Reset ((uint16_t)0xFFFE)
+
+/* I2C START mask */
+#define CR1_START_Set ((uint16_t)0x0100)
+#define CR1_START_Reset ((uint16_t)0xFEFF)
+
+/* I2C STOP mask */
+#define CR1_STOP_Set ((uint16_t)0x0200)
+#define CR1_STOP_Reset ((uint16_t)0xFDFF)
+
+/* I2C ACK mask */
+#define CR1_ACK_Set ((uint16_t)0x0400)
+#define CR1_ACK_Reset ((uint16_t)0xFBFF)
+
+/* I2C ENGC mask */
+#define CR1_ENGC_Set ((uint16_t)0x0040)
+#define CR1_ENGC_Reset ((uint16_t)0xFFBF)
+
+/* I2C SWRST mask */
+#define CR1_SWRST_Set ((uint16_t)0x8000)
+#define CR1_SWRST_Reset ((uint16_t)0x7FFF)
+
+/* I2C PEC mask */
+#define CR1_PEC_Set ((uint16_t)0x1000)
+#define CR1_PEC_Reset ((uint16_t)0xEFFF)
+
+/* I2C ENPEC mask */
+#define CR1_ENPEC_Set ((uint16_t)0x0020)
+#define CR1_ENPEC_Reset ((uint16_t)0xFFDF)
+
+/* I2C ENARP mask */
+#define CR1_ENARP_Set ((uint16_t)0x0010)
+#define CR1_ENARP_Reset ((uint16_t)0xFFEF)
+
+/* I2C NOSTRETCH mask */
+#define CR1_NOSTRETCH_Set ((uint16_t)0x0080)
+#define CR1_NOSTRETCH_Reset ((uint16_t)0xFF7F)
+
+/* I2C registers Masks */
+#define CR1_CLEAR_Mask ((uint16_t)0xFBF5)
+
+/* I2C DMAEN mask */
+#define CR2_DMAEN_Set ((uint16_t)0x0800)
+#define CR2_DMAEN_Reset ((uint16_t)0xF7FF)
+
+/* I2C LAST mask */
+#define CR2_LAST_Set ((uint16_t)0x1000)
+#define CR2_LAST_Reset ((uint16_t)0xEFFF)
+
+/* I2C FREQ mask */
+#define CR2_FREQ_Reset ((uint16_t)0xFFC0)
+
+/* I2C ADD0 mask */
+#define OAR1_ADD0_Set ((uint16_t)0x0001)
+#define OAR1_ADD0_Reset ((uint16_t)0xFFFE)
+
+/* I2C ENDUAL mask */
+#define OAR2_ENDUAL_Set ((uint16_t)0x0001)
+#define OAR2_ENDUAL_Reset ((uint16_t)0xFFFE)
+
+/* I2C ADD2 mask */
+#define OAR2_ADD2_Reset ((uint16_t)0xFF01)
+
+/* I2C F/S mask */
+#define CCR_FS_Set ((uint16_t)0x8000)
+
+/* I2C CCR mask */
+#define CCR_CCR_Set ((uint16_t)0x0FFF)
+
+/* I2C FLAG mask */
+#define FLAG_Mask ((uint32_t)0x00FFFFFF)
+
+/* I2C Interrupt Enable mask */
+#define ITEN_Mask ((uint32_t)0x07000000)
+
+/**
+ * @}
+ */
+
+/** @defgroup I2C_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup I2C_Private_Variables
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup I2C_Private_FunctionPrototypes
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup I2C_Private_Functions
+ * @{
+ */
+
+/**
+ * @brief Deinitializes the I2Cx peripheral registers to their default reset values.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @retval None
+ */
+void I2C_DeInit(I2C_TypeDef* I2Cx)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+
+ if (I2Cx == I2C1)
+ {
+ /* Enable I2C1 reset state */
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C1, ENABLE);
+ /* Release I2C1 from reset state */
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C1, DISABLE);
+ }
+ else
+ {
+ /* Enable I2C2 reset state */
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C2, ENABLE);
+ /* Release I2C2 from reset state */
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_I2C2, DISABLE);
+ }
+}
+
+/**
+ * @brief Initializes the I2Cx peripheral according to the specified
+ * parameters in the I2C_InitStruct.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_InitStruct: pointer to a I2C_InitTypeDef structure that
+ * contains the configuration information for the specified I2C peripheral.
+ * @retval None
+ */
+void I2C_Init(I2C_TypeDef* I2Cx, I2C_InitTypeDef* I2C_InitStruct)
+{
+ uint16_t tmpreg = 0, freqrange = 0;
+ uint16_t result = 0x04;
+ uint32_t pclk1 = 8000000;
+ RCC_ClocksTypeDef rcc_clocks;
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_CLOCK_SPEED(I2C_InitStruct->I2C_ClockSpeed));
+ assert_param(IS_I2C_MODE(I2C_InitStruct->I2C_Mode));
+ assert_param(IS_I2C_DUTY_CYCLE(I2C_InitStruct->I2C_DutyCycle));
+ assert_param(IS_I2C_OWN_ADDRESS1(I2C_InitStruct->I2C_OwnAddress1));
+ assert_param(IS_I2C_ACK_STATE(I2C_InitStruct->I2C_Ack));
+ assert_param(IS_I2C_ACKNOWLEDGE_ADDRESS(I2C_InitStruct->I2C_AcknowledgedAddress));
+
+/*---------------------------- I2Cx CR2 Configuration ------------------------*/
+ /* Get the I2Cx CR2 value */
+ tmpreg = I2Cx->CR2;
+ /* Clear frequency FREQ[5:0] bits */
+ tmpreg &= CR2_FREQ_Reset;
+ /* Get pclk1 frequency value */
+ RCC_GetClocksFreq(&rcc_clocks);
+ pclk1 = rcc_clocks.PCLK1_Frequency;
+ /* Set frequency bits depending on pclk1 value */
+ freqrange = (uint16_t)(pclk1 / 1000000);
+ tmpreg |= freqrange;
+ /* Write to I2Cx CR2 */
+ I2Cx->CR2 = tmpreg;
+
+/*---------------------------- I2Cx CCR Configuration ------------------------*/
+ /* Disable the selected I2C peripheral to configure TRISE */
+ I2Cx->CR1 &= CR1_PE_Reset;
+ /* Reset tmpreg value */
+ /* Clear F/S, DUTY and CCR[11:0] bits */
+ tmpreg = 0;
+
+ /* Configure speed in standard mode */
+ if (I2C_InitStruct->I2C_ClockSpeed <= 100000)
+ {
+ /* Standard mode speed calculate */
+ result = (uint16_t)(pclk1 / (I2C_InitStruct->I2C_ClockSpeed << 1));
+ /* Test if CCR value is under 0x4*/
+ if (result < 0x04)
+ {
+ /* Set minimum allowed value */
+ result = 0x04;
+ }
+ /* Set speed value for standard mode */
+ tmpreg |= result;
+ /* Set Maximum Rise Time for standard mode */
+ I2Cx->TRISE = freqrange + 1;
+ }
+ /* Configure speed in fast mode */
+ else /*(I2C_InitStruct->I2C_ClockSpeed <= 400000)*/
+ {
+ if (I2C_InitStruct->I2C_DutyCycle == I2C_DutyCycle_2)
+ {
+ /* Fast mode speed calculate: Tlow/Thigh = 2 */
+ result = (uint16_t)(pclk1 / (I2C_InitStruct->I2C_ClockSpeed * 3));
+ }
+ else /*I2C_InitStruct->I2C_DutyCycle == I2C_DutyCycle_16_9*/
+ {
+ /* Fast mode speed calculate: Tlow/Thigh = 16/9 */
+ result = (uint16_t)(pclk1 / (I2C_InitStruct->I2C_ClockSpeed * 25));
+ /* Set DUTY bit */
+ result |= I2C_DutyCycle_16_9;
+ }
+
+ /* Test if CCR value is under 0x1*/
+ if ((result & CCR_CCR_Set) == 0)
+ {
+ /* Set minimum allowed value */
+ result |= (uint16_t)0x0001;
+ }
+ /* Set speed value and set F/S bit for fast mode */
+ tmpreg |= (uint16_t)(result | CCR_FS_Set);
+ /* Set Maximum Rise Time for fast mode */
+ I2Cx->TRISE = (uint16_t)(((freqrange * (uint16_t)300) / (uint16_t)1000) + (uint16_t)1);
+ }
+
+ /* Write to I2Cx CCR */
+ I2Cx->CCR = tmpreg;
+ /* Enable the selected I2C peripheral */
+ I2Cx->CR1 |= CR1_PE_Set;
+
+/*---------------------------- I2Cx CR1 Configuration ------------------------*/
+ /* Get the I2Cx CR1 value */
+ tmpreg = I2Cx->CR1;
+ /* Clear ACK, SMBTYPE and SMBUS bits */
+ tmpreg &= CR1_CLEAR_Mask;
+ /* Configure I2Cx: mode and acknowledgement */
+ /* Set SMBTYPE and SMBUS bits according to I2C_Mode value */
+ /* Set ACK bit according to I2C_Ack value */
+ tmpreg |= (uint16_t)((uint32_t)I2C_InitStruct->I2C_Mode | I2C_InitStruct->I2C_Ack);
+ /* Write to I2Cx CR1 */
+ I2Cx->CR1 = tmpreg;
+
+/*---------------------------- I2Cx OAR1 Configuration -----------------------*/
+ /* Set I2Cx Own Address1 and acknowledged address */
+ I2Cx->OAR1 = (I2C_InitStruct->I2C_AcknowledgedAddress | I2C_InitStruct->I2C_OwnAddress1);
+}
+
+/**
+ * @brief Fills each I2C_InitStruct member with its default value.
+ * @param I2C_InitStruct: pointer to an I2C_InitTypeDef structure which will be initialized.
+ * @retval None
+ */
+void I2C_StructInit(I2C_InitTypeDef* I2C_InitStruct)
+{
+/*---------------- Reset I2C init structure parameters values ----------------*/
+ /* initialize the I2C_ClockSpeed member */
+ I2C_InitStruct->I2C_ClockSpeed = 5000;
+ /* Initialize the I2C_Mode member */
+ I2C_InitStruct->I2C_Mode = I2C_Mode_I2C;
+ /* Initialize the I2C_DutyCycle member */
+ I2C_InitStruct->I2C_DutyCycle = I2C_DutyCycle_2;
+ /* Initialize the I2C_OwnAddress1 member */
+ I2C_InitStruct->I2C_OwnAddress1 = 0;
+ /* Initialize the I2C_Ack member */
+ I2C_InitStruct->I2C_Ack = I2C_Ack_Disable;
+ /* Initialize the I2C_AcknowledgedAddress member */
+ I2C_InitStruct->I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
+}
+
+/**
+ * @brief Enables or disables the specified I2C peripheral.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2Cx peripheral.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_Cmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected I2C peripheral */
+ I2Cx->CR1 |= CR1_PE_Set;
+ }
+ else
+ {
+ /* Disable the selected I2C peripheral */
+ I2Cx->CR1 &= CR1_PE_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the specified I2C DMA requests.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C DMA transfer.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_DMACmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected I2C DMA requests */
+ I2Cx->CR2 |= CR2_DMAEN_Set;
+ }
+ else
+ {
+ /* Disable the selected I2C DMA requests */
+ I2Cx->CR2 &= CR2_DMAEN_Reset;
+ }
+}
+
+/**
+ * @brief Specifies if the next DMA transfer will be the last one.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C DMA last transfer.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_DMALastTransferCmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Next DMA transfer is the last transfer */
+ I2Cx->CR2 |= CR2_LAST_Set;
+ }
+ else
+ {
+ /* Next DMA transfer is not the last transfer */
+ I2Cx->CR2 &= CR2_LAST_Reset;
+ }
+}
+
+/**
+ * @brief Generates I2Cx communication START condition.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C START condition generation.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None.
+ */
+void I2C_GenerateSTART(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Generate a START condition */
+ I2Cx->CR1 |= CR1_START_Set;
+ }
+ else
+ {
+ /* Disable the START condition generation */
+ I2Cx->CR1 &= CR1_START_Reset;
+ }
+}
+
+/**
+ * @brief Generates I2Cx communication STOP condition.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C STOP condition generation.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None.
+ */
+void I2C_GenerateSTOP(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Generate a STOP condition */
+ I2Cx->CR1 |= CR1_STOP_Set;
+ }
+ else
+ {
+ /* Disable the STOP condition generation */
+ I2Cx->CR1 &= CR1_STOP_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the specified I2C acknowledge feature.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C Acknowledgement.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None.
+ */
+void I2C_AcknowledgeConfig(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the acknowledgement */
+ I2Cx->CR1 |= CR1_ACK_Set;
+ }
+ else
+ {
+ /* Disable the acknowledgement */
+ I2Cx->CR1 &= CR1_ACK_Reset;
+ }
+}
+
+/**
+ * @brief Configures the specified I2C own address2.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param Address: specifies the 7bit I2C own address2.
+ * @retval None.
+ */
+void I2C_OwnAddress2Config(I2C_TypeDef* I2Cx, uint8_t Address)
+{
+ uint16_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+
+ /* Get the old register value */
+ tmpreg = I2Cx->OAR2;
+
+ /* Reset I2Cx Own address2 bit [7:1] */
+ tmpreg &= OAR2_ADD2_Reset;
+
+ /* Set I2Cx Own address2 */
+ tmpreg |= (uint16_t)((uint16_t)Address & (uint16_t)0x00FE);
+
+ /* Store the new register value */
+ I2Cx->OAR2 = tmpreg;
+}
+
+/**
+ * @brief Enables or disables the specified I2C dual addressing mode.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C dual addressing mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_DualAddressCmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable dual addressing mode */
+ I2Cx->OAR2 |= OAR2_ENDUAL_Set;
+ }
+ else
+ {
+ /* Disable dual addressing mode */
+ I2Cx->OAR2 &= OAR2_ENDUAL_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the specified I2C general call feature.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C General call.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_GeneralCallCmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable generall call */
+ I2Cx->CR1 |= CR1_ENGC_Set;
+ }
+ else
+ {
+ /* Disable generall call */
+ I2Cx->CR1 &= CR1_ENGC_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the specified I2C interrupts.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_IT: specifies the I2C interrupts sources to be enabled or disabled.
+ * This parameter can be any combination of the following values:
+ * @arg I2C_IT_BUF: Buffer interrupt mask
+ * @arg I2C_IT_EVT: Event interrupt mask
+ * @arg I2C_IT_ERR: Error interrupt mask
+ * @param NewState: new state of the specified I2C interrupts.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_ITConfig(I2C_TypeDef* I2Cx, uint16_t I2C_IT, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ assert_param(IS_I2C_CONFIG_IT(I2C_IT));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected I2C interrupts */
+ I2Cx->CR2 |= I2C_IT;
+ }
+ else
+ {
+ /* Disable the selected I2C interrupts */
+ I2Cx->CR2 &= (uint16_t)~I2C_IT;
+ }
+}
+
+/**
+ * @brief Sends a data byte through the I2Cx peripheral.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param Data: Byte to be transmitted..
+ * @retval None
+ */
+void I2C_SendData(I2C_TypeDef* I2Cx, uint8_t Data)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ /* Write in the DR register the data to be sent */
+ I2Cx->DR = Data;
+}
+
+/**
+ * @brief Returns the most recent received data by the I2Cx peripheral.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @retval The value of the received data.
+ */
+uint8_t I2C_ReceiveData(I2C_TypeDef* I2Cx)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ /* Return the data in the DR register */
+ return (uint8_t)I2Cx->DR;
+}
+
+/**
+ * @brief Transmits the address byte to select the slave device.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param Address: specifies the slave address which will be transmitted
+ * @param I2C_Direction: specifies whether the I2C device will be a
+ * Transmitter or a Receiver. This parameter can be one of the following values
+ * @arg I2C_Direction_Transmitter: Transmitter mode
+ * @arg I2C_Direction_Receiver: Receiver mode
+ * @retval None.
+ */
+void I2C_Send7bitAddress(I2C_TypeDef* I2Cx, uint8_t Address, uint8_t I2C_Direction)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_DIRECTION(I2C_Direction));
+ /* Test on the direction to set/reset the read/write bit */
+ if (I2C_Direction != I2C_Direction_Transmitter)
+ {
+ /* Set the address bit0 for read */
+ Address |= OAR1_ADD0_Set;
+ }
+ else
+ {
+ /* Reset the address bit0 for write */
+ Address &= OAR1_ADD0_Reset;
+ }
+ /* Send the address */
+ I2Cx->DR = Address;
+}
+
+/**
+ * @brief Reads the specified I2C register and returns its value.
+ * @param I2C_Register: specifies the register to read.
+ * This parameter can be one of the following values:
+ * @arg I2C_Register_CR1: CR1 register.
+ * @arg I2C_Register_CR2: CR2 register.
+ * @arg I2C_Register_OAR1: OAR1 register.
+ * @arg I2C_Register_OAR2: OAR2 register.
+ * @arg I2C_Register_DR: DR register.
+ * @arg I2C_Register_SR1: SR1 register.
+ * @arg I2C_Register_SR2: SR2 register.
+ * @arg I2C_Register_CCR: CCR register.
+ * @arg I2C_Register_TRISE: TRISE register.
+ * @retval The value of the read register.
+ */
+uint16_t I2C_ReadRegister(I2C_TypeDef* I2Cx, uint8_t I2C_Register)
+{
+ __IO uint32_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_REGISTER(I2C_Register));
+
+ tmp = (uint32_t) I2Cx;
+ tmp += I2C_Register;
+
+ /* Return the selected register value */
+ return (*(__IO uint16_t *) tmp);
+}
+
+/**
+ * @brief Enables or disables the specified I2C software reset.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C software reset.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_SoftwareResetCmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Peripheral under reset */
+ I2Cx->CR1 |= CR1_SWRST_Set;
+ }
+ else
+ {
+ /* Peripheral not under reset */
+ I2Cx->CR1 &= CR1_SWRST_Reset;
+ }
+}
+
+/**
+ * @brief Selects the specified I2C NACK position in master receiver mode.
+ * This function is useful in I2C Master Receiver mode when the number
+ * of data to be received is equal to 2. In this case, this function
+ * should be called (with parameter I2C_NACKPosition_Next) before data
+ * reception starts,as described in the 2-byte reception procedure
+ * recommended in Reference Manual in Section: Master receiver.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_NACKPosition: specifies the NACK position.
+ * This parameter can be one of the following values:
+ * @arg I2C_NACKPosition_Next: indicates that the next byte will be the last
+ * received byte.
+ * @arg I2C_NACKPosition_Current: indicates that current byte is the last
+ * received byte.
+ *
+ * @note This function configures the same bit (POS) as I2C_PECPositionConfig()
+ * but is intended to be used in I2C mode while I2C_PECPositionConfig()
+ * is intended to used in SMBUS mode.
+ *
+ * @retval None
+ */
+void I2C_NACKPositionConfig(I2C_TypeDef* I2Cx, uint16_t I2C_NACKPosition)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_NACK_POSITION(I2C_NACKPosition));
+
+ /* Check the input parameter */
+ if (I2C_NACKPosition == I2C_NACKPosition_Next)
+ {
+ /* Next byte in shift register is the last received byte */
+ I2Cx->CR1 |= I2C_NACKPosition_Next;
+ }
+ else
+ {
+ /* Current byte in shift register is the last received byte */
+ I2Cx->CR1 &= I2C_NACKPosition_Current;
+ }
+}
+
+/**
+ * @brief Drives the SMBusAlert pin high or low for the specified I2C.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_SMBusAlert: specifies SMBAlert pin level.
+ * This parameter can be one of the following values:
+ * @arg I2C_SMBusAlert_Low: SMBAlert pin driven low
+ * @arg I2C_SMBusAlert_High: SMBAlert pin driven high
+ * @retval None
+ */
+void I2C_SMBusAlertConfig(I2C_TypeDef* I2Cx, uint16_t I2C_SMBusAlert)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_SMBUS_ALERT(I2C_SMBusAlert));
+ if (I2C_SMBusAlert == I2C_SMBusAlert_Low)
+ {
+ /* Drive the SMBusAlert pin Low */
+ I2Cx->CR1 |= I2C_SMBusAlert_Low;
+ }
+ else
+ {
+ /* Drive the SMBusAlert pin High */
+ I2Cx->CR1 &= I2C_SMBusAlert_High;
+ }
+}
+
+/**
+ * @brief Enables or disables the specified I2C PEC transfer.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2C PEC transmission.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_TransmitPEC(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected I2C PEC transmission */
+ I2Cx->CR1 |= CR1_PEC_Set;
+ }
+ else
+ {
+ /* Disable the selected I2C PEC transmission */
+ I2Cx->CR1 &= CR1_PEC_Reset;
+ }
+}
+
+/**
+ * @brief Selects the specified I2C PEC position.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_PECPosition: specifies the PEC position.
+ * This parameter can be one of the following values:
+ * @arg I2C_PECPosition_Next: indicates that the next byte is PEC
+ * @arg I2C_PECPosition_Current: indicates that current byte is PEC
+ *
+ * @note This function configures the same bit (POS) as I2C_NACKPositionConfig()
+ * but is intended to be used in SMBUS mode while I2C_NACKPositionConfig()
+ * is intended to used in I2C mode.
+ *
+ * @retval None
+ */
+void I2C_PECPositionConfig(I2C_TypeDef* I2Cx, uint16_t I2C_PECPosition)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_PEC_POSITION(I2C_PECPosition));
+ if (I2C_PECPosition == I2C_PECPosition_Next)
+ {
+ /* Next byte in shift register is PEC */
+ I2Cx->CR1 |= I2C_PECPosition_Next;
+ }
+ else
+ {
+ /* Current byte in shift register is PEC */
+ I2Cx->CR1 &= I2C_PECPosition_Current;
+ }
+}
+
+/**
+ * @brief Enables or disables the PEC value calculation of the transferred bytes.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2Cx PEC value calculation.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_CalculatePEC(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected I2C PEC calculation */
+ I2Cx->CR1 |= CR1_ENPEC_Set;
+ }
+ else
+ {
+ /* Disable the selected I2C PEC calculation */
+ I2Cx->CR1 &= CR1_ENPEC_Reset;
+ }
+}
+
+/**
+ * @brief Returns the PEC value for the specified I2C.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @retval The PEC value.
+ */
+uint8_t I2C_GetPEC(I2C_TypeDef* I2Cx)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ /* Return the selected I2C PEC value */
+ return ((I2Cx->SR2) >> 8);
+}
+
+/**
+ * @brief Enables or disables the specified I2C ARP.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2Cx ARP.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_ARPCmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected I2C ARP */
+ I2Cx->CR1 |= CR1_ENARP_Set;
+ }
+ else
+ {
+ /* Disable the selected I2C ARP */
+ I2Cx->CR1 &= CR1_ENARP_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the specified I2C Clock stretching.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param NewState: new state of the I2Cx Clock stretching.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void I2C_StretchClockCmd(I2C_TypeDef* I2Cx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState == DISABLE)
+ {
+ /* Enable the selected I2C Clock stretching */
+ I2Cx->CR1 |= CR1_NOSTRETCH_Set;
+ }
+ else
+ {
+ /* Disable the selected I2C Clock stretching */
+ I2Cx->CR1 &= CR1_NOSTRETCH_Reset;
+ }
+}
+
+/**
+ * @brief Selects the specified I2C fast mode duty cycle.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_DutyCycle: specifies the fast mode duty cycle.
+ * This parameter can be one of the following values:
+ * @arg I2C_DutyCycle_2: I2C fast mode Tlow/Thigh = 2
+ * @arg I2C_DutyCycle_16_9: I2C fast mode Tlow/Thigh = 16/9
+ * @retval None
+ */
+void I2C_FastModeDutyCycleConfig(I2C_TypeDef* I2Cx, uint16_t I2C_DutyCycle)
+{
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_DUTY_CYCLE(I2C_DutyCycle));
+ if (I2C_DutyCycle != I2C_DutyCycle_16_9)
+ {
+ /* I2C fast mode Tlow/Thigh=2 */
+ I2Cx->CCR &= I2C_DutyCycle_2;
+ }
+ else
+ {
+ /* I2C fast mode Tlow/Thigh=16/9 */
+ I2Cx->CCR |= I2C_DutyCycle_16_9;
+ }
+}
+
+
+
+/**
+ * @brief
+ ****************************************************************************************
+ *
+ * I2C State Monitoring Functions
+ *
+ ****************************************************************************************
+ * This I2C driver provides three different ways for I2C state monitoring
+ * depending on the application requirements and constraints:
+ *
+ *
+ * 1) Basic state monitoring:
+ * Using I2C_CheckEvent() function:
+ * It compares the status registers (SR1 and SR2) content to a given event
+ * (can be the combination of one or more flags).
+ * It returns SUCCESS if the current status includes the given flags
+ * and returns ERROR if one or more flags are missing in the current status.
+ * - When to use:
+ * - This function is suitable for most applications as well as for startup
+ * activity since the events are fully described in the product reference manual
+ * (RM0008).
+ * - It is also suitable for users who need to define their own events.
+ * - Limitations:
+ * - If an error occurs (ie. error flags are set besides to the monitored flags),
+ * the I2C_CheckEvent() function may return SUCCESS despite the communication
+ * hold or corrupted real state.
+ * In this case, it is advised to use error interrupts to monitor the error
+ * events and handle them in the interrupt IRQ handler.
+ *
+ * @note
+ * For error management, it is advised to use the following functions:
+ * - I2C_ITConfig() to configure and enable the error interrupts (I2C_IT_ERR).
+ * - I2Cx_ER_IRQHandler() which is called when the error interrupt occurs.
+ * Where x is the peripheral instance (I2C1, I2C2 ...)
+ * - I2C_GetFlagStatus() or I2C_GetITStatus() to be called into I2Cx_ER_IRQHandler()
+ * in order to determine which error occured.
+ * - I2C_ClearFlag() or I2C_ClearITPendingBit() and/or I2C_SoftwareResetCmd()
+ * and/or I2C_GenerateStop() in order to clear the error flag and source,
+ * and return to correct communication status.
+ *
+ *
+ * 2) Advanced state monitoring:
+ * Using the function I2C_GetLastEvent() which returns the image of both status
+ * registers in a single word (uint32_t) (Status Register 2 value is shifted left
+ * by 16 bits and concatenated to Status Register 1).
+ * - When to use:
+ * - This function is suitable for the same applications above but it allows to
+ * overcome the mentioned limitation of I2C_GetFlagStatus() function.
+ * The returned value could be compared to events already defined in the
+ * library (stm32f10x_i2c.h) or to custom values defined by user.
+ * - This function is suitable when multiple flags are monitored at the same time.
+ * - At the opposite of I2C_CheckEvent() function, this function allows user to
+ * choose when an event is accepted (when all events flags are set and no
+ * other flags are set or just when the needed flags are set like
+ * I2C_CheckEvent() function).
+ * - Limitations:
+ * - User may need to define his own events.
+ * - Same remark concerning the error management is applicable for this
+ * function if user decides to check only regular communication flags (and
+ * ignores error flags).
+ *
+ *
+ * 3) Flag-based state monitoring:
+ * Using the function I2C_GetFlagStatus() which simply returns the status of
+ * one single flag (ie. I2C_FLAG_RXNE ...).
+ * - When to use:
+ * - This function could be used for specific applications or in debug phase.
+ * - It is suitable when only one flag checking is needed (most I2C events
+ * are monitored through multiple flags).
+ * - Limitations:
+ * - When calling this function, the Status register is accessed. Some flags are
+ * cleared when the status register is accessed. So checking the status
+ * of one Flag, may clear other ones.
+ * - Function may need to be called twice or more in order to monitor one
+ * single event.
+ *
+ * For detailed description of Events, please refer to section I2C_Events in
+ * stm32f10x_i2c.h file.
+ *
+ */
+
+/**
+ *
+ * 1) Basic state monitoring
+ *******************************************************************************
+ */
+
+/**
+ * @brief Checks whether the last I2Cx Event is equal to the one passed
+ * as parameter.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_EVENT: specifies the event to be checked.
+ * This parameter can be one of the following values:
+ * @arg I2C_EVENT_SLAVE_TRANSMITTER_ADDRESS_MATCHED : EV1
+ * @arg I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED : EV1
+ * @arg I2C_EVENT_SLAVE_TRANSMITTER_SECONDADDRESS_MATCHED : EV1
+ * @arg I2C_EVENT_SLAVE_RECEIVER_SECONDADDRESS_MATCHED : EV1
+ * @arg I2C_EVENT_SLAVE_GENERALCALLADDRESS_MATCHED : EV1
+ * @arg I2C_EVENT_SLAVE_BYTE_RECEIVED : EV2
+ * @arg (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_DUALF) : EV2
+ * @arg (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_GENCALL) : EV2
+ * @arg I2C_EVENT_SLAVE_BYTE_TRANSMITTED : EV3
+ * @arg (I2C_EVENT_SLAVE_BYTE_TRANSMITTED | I2C_FLAG_DUALF) : EV3
+ * @arg (I2C_EVENT_SLAVE_BYTE_TRANSMITTED | I2C_FLAG_GENCALL) : EV3
+ * @arg I2C_EVENT_SLAVE_ACK_FAILURE : EV3_2
+ * @arg I2C_EVENT_SLAVE_STOP_DETECTED : EV4
+ * @arg I2C_EVENT_MASTER_MODE_SELECT : EV5
+ * @arg I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED : EV6
+ * @arg I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED : EV6
+ * @arg I2C_EVENT_MASTER_BYTE_RECEIVED : EV7
+ * @arg I2C_EVENT_MASTER_BYTE_TRANSMITTING : EV8
+ * @arg I2C_EVENT_MASTER_BYTE_TRANSMITTED : EV8_2
+ * @arg I2C_EVENT_MASTER_MODE_ADDRESS10 : EV9
+ *
+ * @note: For detailed description of Events, please refer to section
+ * I2C_Events in stm32f10x_i2c.h file.
+ *
+ * @retval An ErrorStatus enumeration value:
+ * - SUCCESS: Last event is equal to the I2C_EVENT
+ * - ERROR: Last event is different from the I2C_EVENT
+ */
+ErrorStatus I2C_CheckEvent(I2C_TypeDef* I2Cx, uint32_t I2C_EVENT)
+{
+ uint32_t lastevent = 0;
+ uint32_t flag1 = 0, flag2 = 0;
+ ErrorStatus status = ERROR;
+
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_EVENT(I2C_EVENT));
+
+ /* Read the I2Cx status register */
+ flag1 = I2Cx->SR1;
+ flag2 = I2Cx->SR2;
+ flag2 = flag2 << 16;
+
+ /* Get the last event value from I2C status register */
+ lastevent = (flag1 | flag2) & FLAG_Mask;
+
+ /* Check whether the last event contains the I2C_EVENT */
+ if ((lastevent & I2C_EVENT) == I2C_EVENT)
+ {
+ /* SUCCESS: last event is equal to I2C_EVENT */
+ status = SUCCESS;
+ }
+ else
+ {
+ /* ERROR: last event is different from I2C_EVENT */
+ status = ERROR;
+ }
+ /* Return status */
+ return status;
+}
+
+/**
+ *
+ * 2) Advanced state monitoring
+ *******************************************************************************
+ */
+
+/**
+ * @brief Returns the last I2Cx Event.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ *
+ * @note: For detailed description of Events, please refer to section
+ * I2C_Events in stm32f10x_i2c.h file.
+ *
+ * @retval The last event
+ */
+uint32_t I2C_GetLastEvent(I2C_TypeDef* I2Cx)
+{
+ uint32_t lastevent = 0;
+ uint32_t flag1 = 0, flag2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+
+ /* Read the I2Cx status register */
+ flag1 = I2Cx->SR1;
+ flag2 = I2Cx->SR2;
+ flag2 = flag2 << 16;
+
+ /* Get the last event value from I2C status register */
+ lastevent = (flag1 | flag2) & FLAG_Mask;
+
+ /* Return status */
+ return lastevent;
+}
+
+/**
+ *
+ * 3) Flag-based state monitoring
+ *******************************************************************************
+ */
+
+/**
+ * @brief Checks whether the specified I2C flag is set or not.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_FLAG: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg I2C_FLAG_DUALF: Dual flag (Slave mode)
+ * @arg I2C_FLAG_SMBHOST: SMBus host header (Slave mode)
+ * @arg I2C_FLAG_SMBDEFAULT: SMBus default header (Slave mode)
+ * @arg I2C_FLAG_GENCALL: General call header flag (Slave mode)
+ * @arg I2C_FLAG_TRA: Transmitter/Receiver flag
+ * @arg I2C_FLAG_BUSY: Bus busy flag
+ * @arg I2C_FLAG_MSL: Master/Slave flag
+ * @arg I2C_FLAG_SMBALERT: SMBus Alert flag
+ * @arg I2C_FLAG_TIMEOUT: Timeout or Tlow error flag
+ * @arg I2C_FLAG_PECERR: PEC error in reception flag
+ * @arg I2C_FLAG_OVR: Overrun/Underrun flag (Slave mode)
+ * @arg I2C_FLAG_AF: Acknowledge failure flag
+ * @arg I2C_FLAG_ARLO: Arbitration lost flag (Master mode)
+ * @arg I2C_FLAG_BERR: Bus error flag
+ * @arg I2C_FLAG_TXE: Data register empty flag (Transmitter)
+ * @arg I2C_FLAG_RXNE: Data register not empty (Receiver) flag
+ * @arg I2C_FLAG_STOPF: Stop detection flag (Slave mode)
+ * @arg I2C_FLAG_ADD10: 10-bit header sent flag (Master mode)
+ * @arg I2C_FLAG_BTF: Byte transfer finished flag
+ * @arg I2C_FLAG_ADDR: Address sent flag (Master mode) "ADSL"
+ * Address matched flag (Slave mode)"ENDA"
+ * @arg I2C_FLAG_SB: Start bit flag (Master mode)
+ * @retval The new state of I2C_FLAG (SET or RESET).
+ */
+FlagStatus I2C_GetFlagStatus(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG)
+{
+ FlagStatus bitstatus = RESET;
+ __IO uint32_t i2creg = 0, i2cxbase = 0;
+
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_GET_FLAG(I2C_FLAG));
+
+ /* Get the I2Cx peripheral base address */
+ i2cxbase = (uint32_t)I2Cx;
+
+ /* Read flag register index */
+ i2creg = I2C_FLAG >> 28;
+
+ /* Get bit[23:0] of the flag */
+ I2C_FLAG &= FLAG_Mask;
+
+ if(i2creg != 0)
+ {
+ /* Get the I2Cx SR1 register address */
+ i2cxbase += 0x14;
+ }
+ else
+ {
+ /* Flag in I2Cx SR2 Register */
+ I2C_FLAG = (uint32_t)(I2C_FLAG >> 16);
+ /* Get the I2Cx SR2 register address */
+ i2cxbase += 0x18;
+ }
+
+ if(((*(__IO uint32_t *)i2cxbase) & I2C_FLAG) != (uint32_t)RESET)
+ {
+ /* I2C_FLAG is set */
+ bitstatus = SET;
+ }
+ else
+ {
+ /* I2C_FLAG is reset */
+ bitstatus = RESET;
+ }
+
+ /* Return the I2C_FLAG status */
+ return bitstatus;
+}
+
+
+
+/**
+ * @brief Clears the I2Cx's pending flags.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_FLAG: specifies the flag to clear.
+ * This parameter can be any combination of the following values:
+ * @arg I2C_FLAG_SMBALERT: SMBus Alert flag
+ * @arg I2C_FLAG_TIMEOUT: Timeout or Tlow error flag
+ * @arg I2C_FLAG_PECERR: PEC error in reception flag
+ * @arg I2C_FLAG_OVR: Overrun/Underrun flag (Slave mode)
+ * @arg I2C_FLAG_AF: Acknowledge failure flag
+ * @arg I2C_FLAG_ARLO: Arbitration lost flag (Master mode)
+ * @arg I2C_FLAG_BERR: Bus error flag
+ *
+ * @note
+ * - STOPF (STOP detection) is cleared by software sequence: a read operation
+ * to I2C_SR1 register (I2C_GetFlagStatus()) followed by a write operation
+ * to I2C_CR1 register (I2C_Cmd() to re-enable the I2C peripheral).
+ * - ADD10 (10-bit header sent) is cleared by software sequence: a read
+ * operation to I2C_SR1 (I2C_GetFlagStatus()) followed by writing the
+ * second byte of the address in DR register.
+ * - BTF (Byte Transfer Finished) is cleared by software sequence: a read
+ * operation to I2C_SR1 register (I2C_GetFlagStatus()) followed by a
+ * read/write to I2C_DR register (I2C_SendData()).
+ * - ADDR (Address sent) is cleared by software sequence: a read operation to
+ * I2C_SR1 register (I2C_GetFlagStatus()) followed by a read operation to
+ * I2C_SR2 register ((void)(I2Cx->SR2)).
+ * - SB (Start Bit) is cleared software sequence: a read operation to I2C_SR1
+ * register (I2C_GetFlagStatus()) followed by a write operation to I2C_DR
+ * register (I2C_SendData()).
+ * @retval None
+ */
+void I2C_ClearFlag(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG)
+{
+ uint32_t flagpos = 0;
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_CLEAR_FLAG(I2C_FLAG));
+ /* Get the I2C flag position */
+ flagpos = I2C_FLAG & FLAG_Mask;
+ /* Clear the selected I2C flag */
+ I2Cx->SR1 = (uint16_t)~flagpos;
+}
+
+/**
+ * @brief Checks whether the specified I2C interrupt has occurred or not.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_IT: specifies the interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg I2C_IT_SMBALERT: SMBus Alert flag
+ * @arg I2C_IT_TIMEOUT: Timeout or Tlow error flag
+ * @arg I2C_IT_PECERR: PEC error in reception flag
+ * @arg I2C_IT_OVR: Overrun/Underrun flag (Slave mode)
+ * @arg I2C_IT_AF: Acknowledge failure flag
+ * @arg I2C_IT_ARLO: Arbitration lost flag (Master mode)
+ * @arg I2C_IT_BERR: Bus error flag
+ * @arg I2C_IT_TXE: Data register empty flag (Transmitter)
+ * @arg I2C_IT_RXNE: Data register not empty (Receiver) flag
+ * @arg I2C_IT_STOPF: Stop detection flag (Slave mode)
+ * @arg I2C_IT_ADD10: 10-bit header sent flag (Master mode)
+ * @arg I2C_IT_BTF: Byte transfer finished flag
+ * @arg I2C_IT_ADDR: Address sent flag (Master mode) "ADSL"
+ * Address matched flag (Slave mode)"ENDAD"
+ * @arg I2C_IT_SB: Start bit flag (Master mode)
+ * @retval The new state of I2C_IT (SET or RESET).
+ */
+ITStatus I2C_GetITStatus(I2C_TypeDef* I2Cx, uint32_t I2C_IT)
+{
+ ITStatus bitstatus = RESET;
+ uint32_t enablestatus = 0;
+
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_GET_IT(I2C_IT));
+
+ /* Check if the interrupt source is enabled or not */
+ enablestatus = (uint32_t)(((I2C_IT & ITEN_Mask) >> 16) & (I2Cx->CR2)) ;
+
+ /* Get bit[23:0] of the flag */
+ I2C_IT &= FLAG_Mask;
+
+ /* Check the status of the specified I2C flag */
+ if (((I2Cx->SR1 & I2C_IT) != (uint32_t)RESET) && enablestatus)
+ {
+ /* I2C_IT is set */
+ bitstatus = SET;
+ }
+ else
+ {
+ /* I2C_IT is reset */
+ bitstatus = RESET;
+ }
+ /* Return the I2C_IT status */
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the I2Cx’s interrupt pending bits.
+ * @param I2Cx: where x can be 1 or 2 to select the I2C peripheral.
+ * @param I2C_IT: specifies the interrupt pending bit to clear.
+ * This parameter can be any combination of the following values:
+ * @arg I2C_IT_SMBALERT: SMBus Alert interrupt
+ * @arg I2C_IT_TIMEOUT: Timeout or Tlow error interrupt
+ * @arg I2C_IT_PECERR: PEC error in reception interrupt
+ * @arg I2C_IT_OVR: Overrun/Underrun interrupt (Slave mode)
+ * @arg I2C_IT_AF: Acknowledge failure interrupt
+ * @arg I2C_IT_ARLO: Arbitration lost interrupt (Master mode)
+ * @arg I2C_IT_BERR: Bus error interrupt
+ *
+ * @note
+ * - STOPF (STOP detection) is cleared by software sequence: a read operation
+ * to I2C_SR1 register (I2C_GetITStatus()) followed by a write operation to
+ * I2C_CR1 register (I2C_Cmd() to re-enable the I2C peripheral).
+ * - ADD10 (10-bit header sent) is cleared by software sequence: a read
+ * operation to I2C_SR1 (I2C_GetITStatus()) followed by writing the second
+ * byte of the address in I2C_DR register.
+ * - BTF (Byte Transfer Finished) is cleared by software sequence: a read
+ * operation to I2C_SR1 register (I2C_GetITStatus()) followed by a
+ * read/write to I2C_DR register (I2C_SendData()).
+ * - ADDR (Address sent) is cleared by software sequence: a read operation to
+ * I2C_SR1 register (I2C_GetITStatus()) followed by a read operation to
+ * I2C_SR2 register ((void)(I2Cx->SR2)).
+ * - SB (Start Bit) is cleared by software sequence: a read operation to
+ * I2C_SR1 register (I2C_GetITStatus()) followed by a write operation to
+ * I2C_DR register (I2C_SendData()).
+ * @retval None
+ */
+void I2C_ClearITPendingBit(I2C_TypeDef* I2Cx, uint32_t I2C_IT)
+{
+ uint32_t flagpos = 0;
+ /* Check the parameters */
+ assert_param(IS_I2C_ALL_PERIPH(I2Cx));
+ assert_param(IS_I2C_CLEAR_IT(I2C_IT));
+ /* Get the I2C flag position */
+ flagpos = I2C_IT & FLAG_Mask;
+ /* Clear the selected I2C flag */
+ I2Cx->SR1 = (uint16_t)~flagpos;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_iwdg.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_iwdg.c
new file mode 100644
index 00000000..9d3b0e85
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_iwdg.c
@@ -0,0 +1,190 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x_iwdg.c
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief This file provides all the IWDG firmware functions.
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_tim.h"
+#include "stm32f10x_rcc.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup TIM
+ * @brief TIM driver modules
+ * @{
+ */
+
+/** @defgroup TIM_Private_TypesDefinitions
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Private_Defines
+ * @{
+ */
+
+/* ---------------------- TIM registers bit mask ------------------------ */
+#define SMCR_ETR_Mask ((uint16_t)0x00FF)
+#define CCMR_Offset ((uint16_t)0x0018)
+#define CCER_CCE_Set ((uint16_t)0x0001)
+#define CCER_CCNE_Set ((uint16_t)0x0004)
+
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Private_Variables
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Private_FunctionPrototypes
+ * @{
+ */
+
+static void TI1_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter);
+static void TI2_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter);
+static void TI3_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter);
+static void TI4_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter);
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Private_Variables
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Private_FunctionPrototypes
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup TIM_Private_Functions
+ * @{
+ */
+
+/**
+ * @brief Deinitializes the TIMx peripheral registers to their default reset values.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @retval None
+ */
+void TIM_DeInit(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+
+ if (TIMx == TIM1)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM1, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM1, DISABLE);
+ }
+ else if (TIMx == TIM2)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM2, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM2, DISABLE);
+ }
+ else if (TIMx == TIM3)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM3, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM3, DISABLE);
+ }
+ else if (TIMx == TIM4)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM4, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM4, DISABLE);
+ }
+ else if (TIMx == TIM5)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM5, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM5, DISABLE);
+ }
+ else if (TIMx == TIM6)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM6, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM6, DISABLE);
+ }
+ else if (TIMx == TIM7)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM7, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM7, DISABLE);
+ }
+ else if (TIMx == TIM8)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM8, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM8, DISABLE);
+ }
+ else if (TIMx == TIM9)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM9, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM9, DISABLE);
+ }
+ else if (TIMx == TIM10)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM10, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM10, DISABLE);
+ }
+ else if (TIMx == TIM11)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM11, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM11, DISABLE);
+ }
+ else if (TIMx == TIM12)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM12, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM12, DISABLE);
+ }
+ else if (TIMx == TIM13)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM13, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM13, DISABLE);
+ }
+ else if (TIMx == TIM14)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM14, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_TIM14, DISABLE);
+ }
+ else if (TIMx == TIM15)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM15, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM15, DISABLE);
+ }
+ else if (TIMx == TIM16)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM16, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM16, DISABLE);
+ }
+ else
+ {
+ if (TIMx == TIM17)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM17, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_TIM17, DISABLE);
+ }
+ }
+}
+
+/**
+ * @brief Initializes the TIMx Time Base Unit peripheral according to
+ * the specified parameters in the TIM_TimeBaseInitStruct.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param TIM_TimeBaseInitStruct: pointer to a TIM_TimeBaseInitTypeDef
+ * structure that contains the configuration information for the
+ * specified TIM peripheral.
+ * @retval None
+ */
+void TIM_TimeBaseInit(TIM_TypeDef* TIMx, TIM_TimeBaseInitTypeDef* TIM_TimeBaseInitStruct)
+{
+ uint16_t tmpcr1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_COUNTER_MODE(TIM_TimeBaseInitStruct->TIM_CounterMode));
+ assert_param(IS_TIM_CKD_DIV(TIM_TimeBaseInitStruct->TIM_ClockDivision));
+
+ tmpcr1 = TIMx->CR1;
+
+ if((TIMx == TIM1) || (TIMx == TIM8)|| (TIMx == TIM2) || (TIMx == TIM3)||
+ (TIMx == TIM4) || (TIMx == TIM5))
+ {
+ /* Select the Counter Mode */
+ tmpcr1 &= (uint16_t)(~((uint16_t)(TIM_CR1_DIR | TIM_CR1_CMS)));
+ tmpcr1 |= (uint32_t)TIM_TimeBaseInitStruct->TIM_CounterMode;
+ }
+
+ if((TIMx != TIM6) && (TIMx != TIM7))
+ {
+ /* Set the clock division */
+ tmpcr1 &= (uint16_t)(~((uint16_t)TIM_CR1_CKD));
+ tmpcr1 |= (uint32_t)TIM_TimeBaseInitStruct->TIM_ClockDivision;
+ }
+
+ TIMx->CR1 = tmpcr1;
+
+ /* Set the Autoreload value */
+ TIMx->ARR = TIM_TimeBaseInitStruct->TIM_Period ;
+
+ /* Set the Prescaler value */
+ TIMx->PSC = TIM_TimeBaseInitStruct->TIM_Prescaler;
+
+ if ((TIMx == TIM1) || (TIMx == TIM8)|| (TIMx == TIM15)|| (TIMx == TIM16) || (TIMx == TIM17))
+ {
+ /* Set the Repetition Counter value */
+ TIMx->RCR = TIM_TimeBaseInitStruct->TIM_RepetitionCounter;
+ }
+
+ /* Generate an update event to reload the Prescaler and the Repetition counter
+ values immediately */
+ TIMx->EGR = TIM_PSCReloadMode_Immediate;
+}
+
+/**
+ * @brief Initializes the TIMx Channel1 according to the specified
+ * parameters in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure
+ * that contains the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC1Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint16_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+ /* Disable the Channel 1: Reset the CC1E Bit */
+ TIMx->CCER &= (uint16_t)(~(uint16_t)TIM_CCER_CC1E);
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR1 register value */
+ tmpccmrx = TIMx->CCMR1;
+
+ /* Reset the Output Compare Mode Bits */
+ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMR1_OC1M));
+ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMR1_CC1S));
+
+ /* Select the Output Compare Mode */
+ tmpccmrx |= TIM_OCInitStruct->TIM_OCMode;
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC1P));
+ /* Set the Output Compare Polarity */
+ tmpccer |= TIM_OCInitStruct->TIM_OCPolarity;
+
+ /* Set the Output State */
+ tmpccer |= TIM_OCInitStruct->TIM_OutputState;
+
+ if((TIMx == TIM1) || (TIMx == TIM8)|| (TIMx == TIM15)||
+ (TIMx == TIM16)|| (TIMx == TIM17))
+ {
+ assert_param(IS_TIM_OUTPUTN_STATE(TIM_OCInitStruct->TIM_OutputNState));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCInitStruct->TIM_OCNPolarity));
+ assert_param(IS_TIM_OCNIDLE_STATE(TIM_OCInitStruct->TIM_OCNIdleState));
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+
+ /* Reset the Output N Polarity level */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC1NP));
+ /* Set the Output N Polarity */
+ tmpccer |= TIM_OCInitStruct->TIM_OCNPolarity;
+
+ /* Reset the Output N State */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC1NE));
+ /* Set the Output N State */
+ tmpccer |= TIM_OCInitStruct->TIM_OutputNState;
+
+ /* Reset the Output Compare and Output Compare N IDLE State */
+ tmpcr2 &= (uint16_t)(~((uint16_t)TIM_CR2_OIS1));
+ tmpcr2 &= (uint16_t)(~((uint16_t)TIM_CR2_OIS1N));
+
+ /* Set the Output Idle state */
+ tmpcr2 |= TIM_OCInitStruct->TIM_OCIdleState;
+ /* Set the Output N Idle state */
+ tmpcr2 |= TIM_OCInitStruct->TIM_OCNIdleState;
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR1 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIMx Channel2 according to the specified
+ * parameters in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select
+ * the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure
+ * that contains the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC2Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint16_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+ /* Disable the Channel 2: Reset the CC2E Bit */
+ TIMx->CCER &= (uint16_t)(~((uint16_t)TIM_CCER_CC2E));
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR1 register value */
+ tmpccmrx = TIMx->CCMR1;
+
+ /* Reset the Output Compare mode and Capture/Compare selection Bits */
+ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMR1_OC2M));
+ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMR1_CC2S));
+
+ /* Select the Output Compare Mode */
+ tmpccmrx |= (uint16_t)(TIM_OCInitStruct->TIM_OCMode << 8);
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC2P));
+ /* Set the Output Compare Polarity */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OCPolarity << 4);
+
+ /* Set the Output State */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OutputState << 4);
+
+ if((TIMx == TIM1) || (TIMx == TIM8))
+ {
+ assert_param(IS_TIM_OUTPUTN_STATE(TIM_OCInitStruct->TIM_OutputNState));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCInitStruct->TIM_OCNPolarity));
+ assert_param(IS_TIM_OCNIDLE_STATE(TIM_OCInitStruct->TIM_OCNIdleState));
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+
+ /* Reset the Output N Polarity level */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC2NP));
+ /* Set the Output N Polarity */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OCNPolarity << 4);
+
+ /* Reset the Output N State */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC2NE));
+ /* Set the Output N State */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OutputNState << 4);
+
+ /* Reset the Output Compare and Output Compare N IDLE State */
+ tmpcr2 &= (uint16_t)(~((uint16_t)TIM_CR2_OIS2));
+ tmpcr2 &= (uint16_t)(~((uint16_t)TIM_CR2_OIS2N));
+
+ /* Set the Output Idle state */
+ tmpcr2 |= (uint16_t)(TIM_OCInitStruct->TIM_OCIdleState << 2);
+ /* Set the Output N Idle state */
+ tmpcr2 |= (uint16_t)(TIM_OCInitStruct->TIM_OCNIdleState << 2);
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR2 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIMx Channel3 according to the specified
+ * parameters in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure
+ * that contains the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC3Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint16_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+ /* Disable the Channel 2: Reset the CC2E Bit */
+ TIMx->CCER &= (uint16_t)(~((uint16_t)TIM_CCER_CC3E));
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR2 register value */
+ tmpccmrx = TIMx->CCMR2;
+
+ /* Reset the Output Compare mode and Capture/Compare selection Bits */
+ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMR2_OC3M));
+ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMR2_CC3S));
+ /* Select the Output Compare Mode */
+ tmpccmrx |= TIM_OCInitStruct->TIM_OCMode;
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC3P));
+ /* Set the Output Compare Polarity */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OCPolarity << 8);
+
+ /* Set the Output State */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OutputState << 8);
+
+ if((TIMx == TIM1) || (TIMx == TIM8))
+ {
+ assert_param(IS_TIM_OUTPUTN_STATE(TIM_OCInitStruct->TIM_OutputNState));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCInitStruct->TIM_OCNPolarity));
+ assert_param(IS_TIM_OCNIDLE_STATE(TIM_OCInitStruct->TIM_OCNIdleState));
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+
+ /* Reset the Output N Polarity level */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC3NP));
+ /* Set the Output N Polarity */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OCNPolarity << 8);
+ /* Reset the Output N State */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC3NE));
+
+ /* Set the Output N State */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OutputNState << 8);
+ /* Reset the Output Compare and Output Compare N IDLE State */
+ tmpcr2 &= (uint16_t)(~((uint16_t)TIM_CR2_OIS3));
+ tmpcr2 &= (uint16_t)(~((uint16_t)TIM_CR2_OIS3N));
+ /* Set the Output Idle state */
+ tmpcr2 |= (uint16_t)(TIM_OCInitStruct->TIM_OCIdleState << 4);
+ /* Set the Output N Idle state */
+ tmpcr2 |= (uint16_t)(TIM_OCInitStruct->TIM_OCNIdleState << 4);
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR2 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR3 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIMx Channel4 according to the specified
+ * parameters in the TIM_OCInitStruct.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCInitStruct: pointer to a TIM_OCInitTypeDef structure
+ * that contains the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_OC4Init(TIM_TypeDef* TIMx, TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ uint16_t tmpccmrx = 0, tmpccer = 0, tmpcr2 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_MODE(TIM_OCInitStruct->TIM_OCMode));
+ assert_param(IS_TIM_OUTPUT_STATE(TIM_OCInitStruct->TIM_OutputState));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCInitStruct->TIM_OCPolarity));
+ /* Disable the Channel 2: Reset the CC4E Bit */
+ TIMx->CCER &= (uint16_t)(~((uint16_t)TIM_CCER_CC4E));
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = TIMx->CR2;
+
+ /* Get the TIMx CCMR2 register value */
+ tmpccmrx = TIMx->CCMR2;
+
+ /* Reset the Output Compare mode and Capture/Compare selection Bits */
+ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMR2_OC4M));
+ tmpccmrx &= (uint16_t)(~((uint16_t)TIM_CCMR2_CC4S));
+
+ /* Select the Output Compare Mode */
+ tmpccmrx |= (uint16_t)(TIM_OCInitStruct->TIM_OCMode << 8);
+
+ /* Reset the Output Polarity level */
+ tmpccer &= (uint16_t)(~((uint16_t)TIM_CCER_CC4P));
+ /* Set the Output Compare Polarity */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OCPolarity << 12);
+
+ /* Set the Output State */
+ tmpccer |= (uint16_t)(TIM_OCInitStruct->TIM_OutputState << 12);
+
+ if((TIMx == TIM1) || (TIMx == TIM8))
+ {
+ assert_param(IS_TIM_OCIDLE_STATE(TIM_OCInitStruct->TIM_OCIdleState));
+ /* Reset the Output Compare IDLE State */
+ tmpcr2 &= (uint16_t)(~((uint16_t)TIM_CR2_OIS4));
+ /* Set the Output Idle state */
+ tmpcr2 |= (uint16_t)(TIM_OCInitStruct->TIM_OCIdleState << 6);
+ }
+ /* Write to TIMx CR2 */
+ TIMx->CR2 = tmpcr2;
+
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR2 = tmpccmrx;
+
+ /* Set the Capture Compare Register value */
+ TIMx->CCR4 = TIM_OCInitStruct->TIM_Pulse;
+
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Initializes the TIM peripheral according to the specified
+ * parameters in the TIM_ICInitStruct.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_ICInitStruct: pointer to a TIM_ICInitTypeDef structure
+ * that contains the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_ICInit(TIM_TypeDef* TIMx, TIM_ICInitTypeDef* TIM_ICInitStruct)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CHANNEL(TIM_ICInitStruct->TIM_Channel));
+ assert_param(IS_TIM_IC_SELECTION(TIM_ICInitStruct->TIM_ICSelection));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICInitStruct->TIM_ICPrescaler));
+ assert_param(IS_TIM_IC_FILTER(TIM_ICInitStruct->TIM_ICFilter));
+
+ if((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) ||
+ (TIMx == TIM4) ||(TIMx == TIM5))
+ {
+ assert_param(IS_TIM_IC_POLARITY(TIM_ICInitStruct->TIM_ICPolarity));
+ }
+ else
+ {
+ assert_param(IS_TIM_IC_POLARITY_LITE(TIM_ICInitStruct->TIM_ICPolarity));
+ }
+ if (TIM_ICInitStruct->TIM_Channel == TIM_Channel_1)
+ {
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ /* TI1 Configuration */
+ TI1_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity,
+ TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC1Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+ else if (TIM_ICInitStruct->TIM_Channel == TIM_Channel_2)
+ {
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ /* TI2 Configuration */
+ TI2_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity,
+ TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC2Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+ else if (TIM_ICInitStruct->TIM_Channel == TIM_Channel_3)
+ {
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ /* TI3 Configuration */
+ TI3_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity,
+ TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC3Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+ else
+ {
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ /* TI4 Configuration */
+ TI4_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity,
+ TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC4Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+}
+
+/**
+ * @brief Configures the TIM peripheral according to the specified
+ * parameters in the TIM_ICInitStruct to measure an external PWM signal.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_ICInitStruct: pointer to a TIM_ICInitTypeDef structure
+ * that contains the configuration information for the specified TIM peripheral.
+ * @retval None
+ */
+void TIM_PWMIConfig(TIM_TypeDef* TIMx, TIM_ICInitTypeDef* TIM_ICInitStruct)
+{
+ uint16_t icoppositepolarity = TIM_ICPolarity_Rising;
+ uint16_t icoppositeselection = TIM_ICSelection_DirectTI;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ /* Select the Opposite Input Polarity */
+ if (TIM_ICInitStruct->TIM_ICPolarity == TIM_ICPolarity_Rising)
+ {
+ icoppositepolarity = TIM_ICPolarity_Falling;
+ }
+ else
+ {
+ icoppositepolarity = TIM_ICPolarity_Rising;
+ }
+ /* Select the Opposite Input */
+ if (TIM_ICInitStruct->TIM_ICSelection == TIM_ICSelection_DirectTI)
+ {
+ icoppositeselection = TIM_ICSelection_IndirectTI;
+ }
+ else
+ {
+ icoppositeselection = TIM_ICSelection_DirectTI;
+ }
+ if (TIM_ICInitStruct->TIM_Channel == TIM_Channel_1)
+ {
+ /* TI1 Configuration */
+ TI1_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity, TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC1Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ /* TI2 Configuration */
+ TI2_Config(TIMx, icoppositepolarity, icoppositeselection, TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC2Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+ else
+ {
+ /* TI2 Configuration */
+ TI2_Config(TIMx, TIM_ICInitStruct->TIM_ICPolarity, TIM_ICInitStruct->TIM_ICSelection,
+ TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC2Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ /* TI1 Configuration */
+ TI1_Config(TIMx, icoppositepolarity, icoppositeselection, TIM_ICInitStruct->TIM_ICFilter);
+ /* Set the Input Capture Prescaler value */
+ TIM_SetIC1Prescaler(TIMx, TIM_ICInitStruct->TIM_ICPrescaler);
+ }
+}
+
+/**
+ * @brief Configures the: Break feature, dead time, Lock level, the OSSI,
+ * the OSSR State and the AOE(automatic output enable).
+ * @param TIMx: where x can be 1 or 8 to select the TIM
+ * @param TIM_BDTRInitStruct: pointer to a TIM_BDTRInitTypeDef structure that
+ * contains the BDTR Register configuration information for the TIM peripheral.
+ * @retval None
+ */
+void TIM_BDTRConfig(TIM_TypeDef* TIMx, TIM_BDTRInitTypeDef *TIM_BDTRInitStruct)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_OSSR_STATE(TIM_BDTRInitStruct->TIM_OSSRState));
+ assert_param(IS_TIM_OSSI_STATE(TIM_BDTRInitStruct->TIM_OSSIState));
+ assert_param(IS_TIM_LOCK_LEVEL(TIM_BDTRInitStruct->TIM_LOCKLevel));
+ assert_param(IS_TIM_BREAK_STATE(TIM_BDTRInitStruct->TIM_Break));
+ assert_param(IS_TIM_BREAK_POLARITY(TIM_BDTRInitStruct->TIM_BreakPolarity));
+ assert_param(IS_TIM_AUTOMATIC_OUTPUT_STATE(TIM_BDTRInitStruct->TIM_AutomaticOutput));
+ /* Set the Lock level, the Break enable Bit and the Ploarity, the OSSR State,
+ the OSSI State, the dead time value and the Automatic Output Enable Bit */
+ TIMx->BDTR = (uint32_t)TIM_BDTRInitStruct->TIM_OSSRState | TIM_BDTRInitStruct->TIM_OSSIState |
+ TIM_BDTRInitStruct->TIM_LOCKLevel | TIM_BDTRInitStruct->TIM_DeadTime |
+ TIM_BDTRInitStruct->TIM_Break | TIM_BDTRInitStruct->TIM_BreakPolarity |
+ TIM_BDTRInitStruct->TIM_AutomaticOutput;
+}
+
+/**
+ * @brief Fills each TIM_TimeBaseInitStruct member with its default value.
+ * @param TIM_TimeBaseInitStruct : pointer to a TIM_TimeBaseInitTypeDef
+ * structure which will be initialized.
+ * @retval None
+ */
+void TIM_TimeBaseStructInit(TIM_TimeBaseInitTypeDef* TIM_TimeBaseInitStruct)
+{
+ /* Set the default configuration */
+ TIM_TimeBaseInitStruct->TIM_Period = 0xFFFF;
+ TIM_TimeBaseInitStruct->TIM_Prescaler = 0x0000;
+ TIM_TimeBaseInitStruct->TIM_ClockDivision = TIM_CKD_DIV1;
+ TIM_TimeBaseInitStruct->TIM_CounterMode = TIM_CounterMode_Up;
+ TIM_TimeBaseInitStruct->TIM_RepetitionCounter = 0x0000;
+}
+
+/**
+ * @brief Fills each TIM_OCInitStruct member with its default value.
+ * @param TIM_OCInitStruct : pointer to a TIM_OCInitTypeDef structure which will
+ * be initialized.
+ * @retval None
+ */
+void TIM_OCStructInit(TIM_OCInitTypeDef* TIM_OCInitStruct)
+{
+ /* Set the default configuration */
+ TIM_OCInitStruct->TIM_OCMode = TIM_OCMode_Timing;
+ TIM_OCInitStruct->TIM_OutputState = TIM_OutputState_Disable;
+ TIM_OCInitStruct->TIM_OutputNState = TIM_OutputNState_Disable;
+ TIM_OCInitStruct->TIM_Pulse = 0x0000;
+ TIM_OCInitStruct->TIM_OCPolarity = TIM_OCPolarity_High;
+ TIM_OCInitStruct->TIM_OCNPolarity = TIM_OCPolarity_High;
+ TIM_OCInitStruct->TIM_OCIdleState = TIM_OCIdleState_Reset;
+ TIM_OCInitStruct->TIM_OCNIdleState = TIM_OCNIdleState_Reset;
+}
+
+/**
+ * @brief Fills each TIM_ICInitStruct member with its default value.
+ * @param TIM_ICInitStruct: pointer to a TIM_ICInitTypeDef structure which will
+ * be initialized.
+ * @retval None
+ */
+void TIM_ICStructInit(TIM_ICInitTypeDef* TIM_ICInitStruct)
+{
+ /* Set the default configuration */
+ TIM_ICInitStruct->TIM_Channel = TIM_Channel_1;
+ TIM_ICInitStruct->TIM_ICPolarity = TIM_ICPolarity_Rising;
+ TIM_ICInitStruct->TIM_ICSelection = TIM_ICSelection_DirectTI;
+ TIM_ICInitStruct->TIM_ICPrescaler = TIM_ICPSC_DIV1;
+ TIM_ICInitStruct->TIM_ICFilter = 0x00;
+}
+
+/**
+ * @brief Fills each TIM_BDTRInitStruct member with its default value.
+ * @param TIM_BDTRInitStruct: pointer to a TIM_BDTRInitTypeDef structure which
+ * will be initialized.
+ * @retval None
+ */
+void TIM_BDTRStructInit(TIM_BDTRInitTypeDef* TIM_BDTRInitStruct)
+{
+ /* Set the default configuration */
+ TIM_BDTRInitStruct->TIM_OSSRState = TIM_OSSRState_Disable;
+ TIM_BDTRInitStruct->TIM_OSSIState = TIM_OSSIState_Disable;
+ TIM_BDTRInitStruct->TIM_LOCKLevel = TIM_LOCKLevel_OFF;
+ TIM_BDTRInitStruct->TIM_DeadTime = 0x00;
+ TIM_BDTRInitStruct->TIM_Break = TIM_Break_Disable;
+ TIM_BDTRInitStruct->TIM_BreakPolarity = TIM_BreakPolarity_Low;
+ TIM_BDTRInitStruct->TIM_AutomaticOutput = TIM_AutomaticOutput_Disable;
+}
+
+/**
+ * @brief Enables or disables the specified TIM peripheral.
+ * @param TIMx: where x can be 1 to 17 to select the TIMx peripheral.
+ * @param NewState: new state of the TIMx peripheral.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_Cmd(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the TIM Counter */
+ TIMx->CR1 |= TIM_CR1_CEN;
+ }
+ else
+ {
+ /* Disable the TIM Counter */
+ TIMx->CR1 &= (uint16_t)(~((uint16_t)TIM_CR1_CEN));
+ }
+}
+
+/**
+ * @brief Enables or disables the TIM peripheral Main Outputs.
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIMx peripheral.
+ * @param NewState: new state of the TIM peripheral Main Outputs.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_CtrlPWMOutputs(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the TIM Main Output */
+ TIMx->BDTR |= TIM_BDTR_MOE;
+ }
+ else
+ {
+ /* Disable the TIM Main Output */
+ TIMx->BDTR &= (uint16_t)(~((uint16_t)TIM_BDTR_MOE));
+ }
+}
+
+/**
+ * @brief Enables or disables the specified TIM interrupts.
+ * @param TIMx: where x can be 1 to 17 to select the TIMx peripheral.
+ * @param TIM_IT: specifies the TIM interrupts sources to be enabled or disabled.
+ * This parameter can be any combination of the following values:
+ * @arg TIM_IT_Update: TIM update Interrupt source
+ * @arg TIM_IT_CC1: TIM Capture Compare 1 Interrupt source
+ * @arg TIM_IT_CC2: TIM Capture Compare 2 Interrupt source
+ * @arg TIM_IT_CC3: TIM Capture Compare 3 Interrupt source
+ * @arg TIM_IT_CC4: TIM Capture Compare 4 Interrupt source
+ * @arg TIM_IT_COM: TIM Commutation Interrupt source
+ * @arg TIM_IT_Trigger: TIM Trigger Interrupt source
+ * @arg TIM_IT_Break: TIM Break Interrupt source
+ * @note
+ * - TIM6 and TIM7 can only generate an update interrupt.
+ * - TIM9, TIM12 and TIM15 can have only TIM_IT_Update, TIM_IT_CC1,
+ * TIM_IT_CC2 or TIM_IT_Trigger.
+ * - TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_IT_Update or TIM_IT_CC1.
+ * - TIM_IT_Break is used only with TIM1, TIM8 and TIM15.
+ * - TIM_IT_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.
+ * @param NewState: new state of the TIM interrupts.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_ITConfig(TIM_TypeDef* TIMx, uint16_t TIM_IT, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_IT(TIM_IT));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the Interrupt sources */
+ TIMx->DIER |= TIM_IT;
+ }
+ else
+ {
+ /* Disable the Interrupt sources */
+ TIMx->DIER &= (uint16_t)~TIM_IT;
+ }
+}
+
+/**
+ * @brief Configures the TIMx event to be generate by software.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param TIM_EventSource: specifies the event source.
+ * This parameter can be one or more of the following values:
+ * @arg TIM_EventSource_Update: Timer update Event source
+ * @arg TIM_EventSource_CC1: Timer Capture Compare 1 Event source
+ * @arg TIM_EventSource_CC2: Timer Capture Compare 2 Event source
+ * @arg TIM_EventSource_CC3: Timer Capture Compare 3 Event source
+ * @arg TIM_EventSource_CC4: Timer Capture Compare 4 Event source
+ * @arg TIM_EventSource_COM: Timer COM event source
+ * @arg TIM_EventSource_Trigger: Timer Trigger Event source
+ * @arg TIM_EventSource_Break: Timer Break event source
+ * @note
+ * - TIM6 and TIM7 can only generate an update event.
+ * - TIM_EventSource_COM and TIM_EventSource_Break are used only with TIM1 and TIM8.
+ * @retval None
+ */
+void TIM_GenerateEvent(TIM_TypeDef* TIMx, uint16_t TIM_EventSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_EVENT_SOURCE(TIM_EventSource));
+
+ /* Set the event sources */
+ TIMx->EGR = TIM_EventSource;
+}
+
+/**
+ * @brief Configures the TIMx's DMA interface.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 15, 16 or 17 to select
+ * the TIM peripheral.
+ * @param TIM_DMABase: DMA Base address.
+ * This parameter can be one of the following values:
+ * @arg TIM_DMABase_CR, TIM_DMABase_CR2, TIM_DMABase_SMCR,
+ * TIM_DMABase_DIER, TIM1_DMABase_SR, TIM_DMABase_EGR,
+ * TIM_DMABase_CCMR1, TIM_DMABase_CCMR2, TIM_DMABase_CCER,
+ * TIM_DMABase_CNT, TIM_DMABase_PSC, TIM_DMABase_ARR,
+ * TIM_DMABase_RCR, TIM_DMABase_CCR1, TIM_DMABase_CCR2,
+ * TIM_DMABase_CCR3, TIM_DMABase_CCR4, TIM_DMABase_BDTR,
+ * TIM_DMABase_DCR.
+ * @param TIM_DMABurstLength: DMA Burst length.
+ * This parameter can be one value between:
+ * TIM_DMABurstLength_1Transfer and TIM_DMABurstLength_18Transfers.
+ * @retval None
+ */
+void TIM_DMAConfig(TIM_TypeDef* TIMx, uint16_t TIM_DMABase, uint16_t TIM_DMABurstLength)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_TIM_DMA_BASE(TIM_DMABase));
+ assert_param(IS_TIM_DMA_LENGTH(TIM_DMABurstLength));
+ /* Set the DMA Base and the DMA Burst Length */
+ TIMx->DCR = TIM_DMABase | TIM_DMABurstLength;
+}
+
+/**
+ * @brief Enables or disables the TIMx's DMA Requests.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 6, 7, 8, 15, 16 or 17
+ * to select the TIM peripheral.
+ * @param TIM_DMASource: specifies the DMA Request sources.
+ * This parameter can be any combination of the following values:
+ * @arg TIM_DMA_Update: TIM update Interrupt source
+ * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source
+ * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source
+ * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source
+ * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source
+ * @arg TIM_DMA_COM: TIM Commutation DMA source
+ * @arg TIM_DMA_Trigger: TIM Trigger DMA source
+ * @param NewState: new state of the DMA Request sources.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_DMACmd(TIM_TypeDef* TIMx, uint16_t TIM_DMASource, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST9_PERIPH(TIMx));
+ assert_param(IS_TIM_DMA_SOURCE(TIM_DMASource));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the DMA sources */
+ TIMx->DIER |= TIM_DMASource;
+ }
+ else
+ {
+ /* Disable the DMA sources */
+ TIMx->DIER &= (uint16_t)~TIM_DMASource;
+ }
+}
+
+/**
+ * @brief Configures the TIMx internal Clock
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15
+ * to select the TIM peripheral.
+ * @retval None
+ */
+void TIM_InternalClockConfig(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ /* Disable slave mode to clock the prescaler directly with the internal clock */
+ TIMx->SMCR &= (uint16_t)(~((uint16_t)TIM_SMCR_SMS));
+}
+
+/**
+ * @brief Configures the TIMx Internal Trigger as External Clock
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_ITRSource: Trigger source.
+ * This parameter can be one of the following values:
+ * @param TIM_TS_ITR0: Internal Trigger 0
+ * @param TIM_TS_ITR1: Internal Trigger 1
+ * @param TIM_TS_ITR2: Internal Trigger 2
+ * @param TIM_TS_ITR3: Internal Trigger 3
+ * @retval None
+ */
+void TIM_ITRxExternalClockConfig(TIM_TypeDef* TIMx, uint16_t TIM_InputTriggerSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_INTERNAL_TRIGGER_SELECTION(TIM_InputTriggerSource));
+ /* Select the Internal Trigger */
+ TIM_SelectInputTrigger(TIMx, TIM_InputTriggerSource);
+ /* Select the External clock mode1 */
+ TIMx->SMCR |= TIM_SlaveMode_External1;
+}
+
+/**
+ * @brief Configures the TIMx Trigger as External Clock
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_TIxExternalCLKSource: Trigger source.
+ * This parameter can be one of the following values:
+ * @arg TIM_TIxExternalCLK1Source_TI1ED: TI1 Edge Detector
+ * @arg TIM_TIxExternalCLK1Source_TI1: Filtered Timer Input 1
+ * @arg TIM_TIxExternalCLK1Source_TI2: Filtered Timer Input 2
+ * @param TIM_ICPolarity: specifies the TIx Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @param ICFilter : specifies the filter value.
+ * This parameter must be a value between 0x0 and 0xF.
+ * @retval None
+ */
+void TIM_TIxExternalClockConfig(TIM_TypeDef* TIMx, uint16_t TIM_TIxExternalCLKSource,
+ uint16_t TIM_ICPolarity, uint16_t ICFilter)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_TIXCLK_SOURCE(TIM_TIxExternalCLKSource));
+ assert_param(IS_TIM_IC_POLARITY(TIM_ICPolarity));
+ assert_param(IS_TIM_IC_FILTER(ICFilter));
+ /* Configure the Timer Input Clock Source */
+ if (TIM_TIxExternalCLKSource == TIM_TIxExternalCLK1Source_TI2)
+ {
+ TI2_Config(TIMx, TIM_ICPolarity, TIM_ICSelection_DirectTI, ICFilter);
+ }
+ else
+ {
+ TI1_Config(TIMx, TIM_ICPolarity, TIM_ICSelection_DirectTI, ICFilter);
+ }
+ /* Select the Trigger source */
+ TIM_SelectInputTrigger(TIMx, TIM_TIxExternalCLKSource);
+ /* Select the External clock mode1 */
+ TIMx->SMCR |= TIM_SlaveMode_External1;
+}
+
+/**
+ * @brief Configures the External clock Mode1
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ExtTRGPrescaler: The external Trigger Prescaler.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF.
+ * @arg TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2.
+ * @arg TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4.
+ * @arg TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
+ * @param TIM_ExtTRGPolarity: The external Trigger Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPolarity_Inverted: active low or falling edge active.
+ * @arg TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
+ * @param ExtTRGFilter: External Trigger Filter.
+ * This parameter must be a value between 0x00 and 0x0F
+ * @retval None
+ */
+void TIM_ETRClockMode1Config(TIM_TypeDef* TIMx, uint16_t TIM_ExtTRGPrescaler, uint16_t TIM_ExtTRGPolarity,
+ uint16_t ExtTRGFilter)
+{
+ uint16_t tmpsmcr = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_EXT_PRESCALER(TIM_ExtTRGPrescaler));
+ assert_param(IS_TIM_EXT_POLARITY(TIM_ExtTRGPolarity));
+ assert_param(IS_TIM_EXT_FILTER(ExtTRGFilter));
+ /* Configure the ETR Clock source */
+ TIM_ETRConfig(TIMx, TIM_ExtTRGPrescaler, TIM_ExtTRGPolarity, ExtTRGFilter);
+
+ /* Get the TIMx SMCR register value */
+ tmpsmcr = TIMx->SMCR;
+ /* Reset the SMS Bits */
+ tmpsmcr &= (uint16_t)(~((uint16_t)TIM_SMCR_SMS));
+ /* Select the External clock mode1 */
+ tmpsmcr |= TIM_SlaveMode_External1;
+ /* Select the Trigger selection : ETRF */
+ tmpsmcr &= (uint16_t)(~((uint16_t)TIM_SMCR_TS));
+ tmpsmcr |= TIM_TS_ETRF;
+ /* Write to TIMx SMCR */
+ TIMx->SMCR = tmpsmcr;
+}
+
+/**
+ * @brief Configures the External clock Mode2
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ExtTRGPrescaler: The external Trigger Prescaler.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF.
+ * @arg TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2.
+ * @arg TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4.
+ * @arg TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
+ * @param TIM_ExtTRGPolarity: The external Trigger Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPolarity_Inverted: active low or falling edge active.
+ * @arg TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
+ * @param ExtTRGFilter: External Trigger Filter.
+ * This parameter must be a value between 0x00 and 0x0F
+ * @retval None
+ */
+void TIM_ETRClockMode2Config(TIM_TypeDef* TIMx, uint16_t TIM_ExtTRGPrescaler,
+ uint16_t TIM_ExtTRGPolarity, uint16_t ExtTRGFilter)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_EXT_PRESCALER(TIM_ExtTRGPrescaler));
+ assert_param(IS_TIM_EXT_POLARITY(TIM_ExtTRGPolarity));
+ assert_param(IS_TIM_EXT_FILTER(ExtTRGFilter));
+ /* Configure the ETR Clock source */
+ TIM_ETRConfig(TIMx, TIM_ExtTRGPrescaler, TIM_ExtTRGPolarity, ExtTRGFilter);
+ /* Enable the External clock mode2 */
+ TIMx->SMCR |= TIM_SMCR_ECE;
+}
+
+/**
+ * @brief Configures the TIMx External Trigger (ETR).
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ExtTRGPrescaler: The external Trigger Prescaler.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF.
+ * @arg TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2.
+ * @arg TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4.
+ * @arg TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
+ * @param TIM_ExtTRGPolarity: The external Trigger Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ExtTRGPolarity_Inverted: active low or falling edge active.
+ * @arg TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
+ * @param ExtTRGFilter: External Trigger Filter.
+ * This parameter must be a value between 0x00 and 0x0F
+ * @retval None
+ */
+void TIM_ETRConfig(TIM_TypeDef* TIMx, uint16_t TIM_ExtTRGPrescaler, uint16_t TIM_ExtTRGPolarity,
+ uint16_t ExtTRGFilter)
+{
+ uint16_t tmpsmcr = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_EXT_PRESCALER(TIM_ExtTRGPrescaler));
+ assert_param(IS_TIM_EXT_POLARITY(TIM_ExtTRGPolarity));
+ assert_param(IS_TIM_EXT_FILTER(ExtTRGFilter));
+ tmpsmcr = TIMx->SMCR;
+ /* Reset the ETR Bits */
+ tmpsmcr &= SMCR_ETR_Mask;
+ /* Set the Prescaler, the Filter value and the Polarity */
+ tmpsmcr |= (uint16_t)(TIM_ExtTRGPrescaler | (uint16_t)(TIM_ExtTRGPolarity | (uint16_t)(ExtTRGFilter << (uint16_t)8)));
+ /* Write to TIMx SMCR */
+ TIMx->SMCR = tmpsmcr;
+}
+
+/**
+ * @brief Configures the TIMx Prescaler.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param Prescaler: specifies the Prescaler Register value
+ * @param TIM_PSCReloadMode: specifies the TIM Prescaler Reload mode
+ * This parameter can be one of the following values:
+ * @arg TIM_PSCReloadMode_Update: The Prescaler is loaded at the update event.
+ * @arg TIM_PSCReloadMode_Immediate: The Prescaler is loaded immediately.
+ * @retval None
+ */
+void TIM_PrescalerConfig(TIM_TypeDef* TIMx, uint16_t Prescaler, uint16_t TIM_PSCReloadMode)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_PRESCALER_RELOAD(TIM_PSCReloadMode));
+ /* Set the Prescaler value */
+ TIMx->PSC = Prescaler;
+ /* Set or reset the UG Bit */
+ TIMx->EGR = TIM_PSCReloadMode;
+}
+
+/**
+ * @brief Specifies the TIMx Counter Mode to be used.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_CounterMode: specifies the Counter Mode to be used
+ * This parameter can be one of the following values:
+ * @arg TIM_CounterMode_Up: TIM Up Counting Mode
+ * @arg TIM_CounterMode_Down: TIM Down Counting Mode
+ * @arg TIM_CounterMode_CenterAligned1: TIM Center Aligned Mode1
+ * @arg TIM_CounterMode_CenterAligned2: TIM Center Aligned Mode2
+ * @arg TIM_CounterMode_CenterAligned3: TIM Center Aligned Mode3
+ * @retval None
+ */
+void TIM_CounterModeConfig(TIM_TypeDef* TIMx, uint16_t TIM_CounterMode)
+{
+ uint16_t tmpcr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_COUNTER_MODE(TIM_CounterMode));
+ tmpcr1 = TIMx->CR1;
+ /* Reset the CMS and DIR Bits */
+ tmpcr1 &= (uint16_t)(~((uint16_t)(TIM_CR1_DIR | TIM_CR1_CMS)));
+ /* Set the Counter Mode */
+ tmpcr1 |= TIM_CounterMode;
+ /* Write to TIMx CR1 register */
+ TIMx->CR1 = tmpcr1;
+}
+
+/**
+ * @brief Selects the Input Trigger source
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_InputTriggerSource: The Input Trigger source.
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal Trigger 0
+ * @arg TIM_TS_ITR1: Internal Trigger 1
+ * @arg TIM_TS_ITR2: Internal Trigger 2
+ * @arg TIM_TS_ITR3: Internal Trigger 3
+ * @arg TIM_TS_TI1F_ED: TI1 Edge Detector
+ * @arg TIM_TS_TI1FP1: Filtered Timer Input 1
+ * @arg TIM_TS_TI2FP2: Filtered Timer Input 2
+ * @arg TIM_TS_ETRF: External Trigger input
+ * @retval None
+ */
+void TIM_SelectInputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_InputTriggerSource)
+{
+ uint16_t tmpsmcr = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_TRIGGER_SELECTION(TIM_InputTriggerSource));
+ /* Get the TIMx SMCR register value */
+ tmpsmcr = TIMx->SMCR;
+ /* Reset the TS Bits */
+ tmpsmcr &= (uint16_t)(~((uint16_t)TIM_SMCR_TS));
+ /* Set the Input Trigger source */
+ tmpsmcr |= TIM_InputTriggerSource;
+ /* Write to TIMx SMCR */
+ TIMx->SMCR = tmpsmcr;
+}
+
+/**
+ * @brief Configures the TIMx Encoder Interface.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_EncoderMode: specifies the TIMx Encoder Mode.
+ * This parameter can be one of the following values:
+ * @arg TIM_EncoderMode_TI1: Counter counts on TI1FP1 edge depending on TI2FP2 level.
+ * @arg TIM_EncoderMode_TI2: Counter counts on TI2FP2 edge depending on TI1FP1 level.
+ * @arg TIM_EncoderMode_TI12: Counter counts on both TI1FP1 and TI2FP2 edges depending
+ * on the level of the other input.
+ * @param TIM_IC1Polarity: specifies the IC1 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Falling: IC Falling edge.
+ * @arg TIM_ICPolarity_Rising: IC Rising edge.
+ * @param TIM_IC2Polarity: specifies the IC2 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Falling: IC Falling edge.
+ * @arg TIM_ICPolarity_Rising: IC Rising edge.
+ * @retval None
+ */
+void TIM_EncoderInterfaceConfig(TIM_TypeDef* TIMx, uint16_t TIM_EncoderMode,
+ uint16_t TIM_IC1Polarity, uint16_t TIM_IC2Polarity)
+{
+ uint16_t tmpsmcr = 0;
+ uint16_t tmpccmr1 = 0;
+ uint16_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST5_PERIPH(TIMx));
+ assert_param(IS_TIM_ENCODER_MODE(TIM_EncoderMode));
+ assert_param(IS_TIM_IC_POLARITY(TIM_IC1Polarity));
+ assert_param(IS_TIM_IC_POLARITY(TIM_IC2Polarity));
+
+ /* Get the TIMx SMCR register value */
+ tmpsmcr = TIMx->SMCR;
+
+ /* Get the TIMx CCMR1 register value */
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Get the TIMx CCER register value */
+ tmpccer = TIMx->CCER;
+
+ /* Set the encoder Mode */
+ tmpsmcr &= (uint16_t)(~((uint16_t)TIM_SMCR_SMS));
+ tmpsmcr |= TIM_EncoderMode;
+
+ /* Select the Capture Compare 1 and the Capture Compare 2 as input */
+ tmpccmr1 &= (uint16_t)(((uint16_t)~((uint16_t)TIM_CCMR1_CC1S)) & (uint16_t)(~((uint16_t)TIM_CCMR1_CC2S)));
+ tmpccmr1 |= TIM_CCMR1_CC1S_0 | TIM_CCMR1_CC2S_0;
+
+ /* Set the TI1 and the TI2 Polarities */
+ tmpccer &= (uint16_t)(((uint16_t)~((uint16_t)TIM_CCER_CC1P)) & ((uint16_t)~((uint16_t)TIM_CCER_CC2P)));
+ tmpccer |= (uint16_t)(TIM_IC1Polarity | (uint16_t)(TIM_IC2Polarity << (uint16_t)4));
+
+ /* Write to TIMx SMCR */
+ TIMx->SMCR = tmpsmcr;
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmr1;
+ /* Write to TIMx CCER */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Forces the TIMx output 1 waveform to active or inactive level.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC1REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC1REF.
+ * @retval None
+ */
+void TIM_ForcedOC1Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint16_t tmpccmr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr1 = TIMx->CCMR1;
+ /* Reset the OC1M Bits */
+ tmpccmr1 &= (uint16_t)~((uint16_t)TIM_CCMR1_OC1M);
+ /* Configure The Forced output Mode */
+ tmpccmr1 |= TIM_ForcedAction;
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Forces the TIMx output 2 waveform to active or inactive level.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC2REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC2REF.
+ * @retval None
+ */
+void TIM_ForcedOC2Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint16_t tmpccmr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr1 = TIMx->CCMR1;
+ /* Reset the OC2M Bits */
+ tmpccmr1 &= (uint16_t)~((uint16_t)TIM_CCMR1_OC2M);
+ /* Configure The Forced output Mode */
+ tmpccmr1 |= (uint16_t)(TIM_ForcedAction << 8);
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Forces the TIMx output 3 waveform to active or inactive level.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC3REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC3REF.
+ * @retval None
+ */
+void TIM_ForcedOC3Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint16_t tmpccmr2 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr2 = TIMx->CCMR2;
+ /* Reset the OC1M Bits */
+ tmpccmr2 &= (uint16_t)~((uint16_t)TIM_CCMR2_OC3M);
+ /* Configure The Forced output Mode */
+ tmpccmr2 |= TIM_ForcedAction;
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Forces the TIMx output 4 waveform to active or inactive level.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ForcedAction: specifies the forced Action to be set to the output waveform.
+ * This parameter can be one of the following values:
+ * @arg TIM_ForcedAction_Active: Force active level on OC4REF
+ * @arg TIM_ForcedAction_InActive: Force inactive level on OC4REF.
+ * @retval None
+ */
+void TIM_ForcedOC4Config(TIM_TypeDef* TIMx, uint16_t TIM_ForcedAction)
+{
+ uint16_t tmpccmr2 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_FORCED_ACTION(TIM_ForcedAction));
+ tmpccmr2 = TIMx->CCMR2;
+ /* Reset the OC2M Bits */
+ tmpccmr2 &= (uint16_t)~((uint16_t)TIM_CCMR2_OC4M);
+ /* Configure The Forced output Mode */
+ tmpccmr2 |= (uint16_t)(TIM_ForcedAction << 8);
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Enables or disables TIMx peripheral Preload register on ARR.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param NewState: new state of the TIMx peripheral Preload register
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_ARRPreloadConfig(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Set the ARR Preload Bit */
+ TIMx->CR1 |= TIM_CR1_ARPE;
+ }
+ else
+ {
+ /* Reset the ARR Preload Bit */
+ TIMx->CR1 &= (uint16_t)~((uint16_t)TIM_CR1_ARPE);
+ }
+}
+
+/**
+ * @brief Selects the TIM peripheral Commutation event.
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIMx peripheral
+ * @param NewState: new state of the Commutation event.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectCOM(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Set the COM Bit */
+ TIMx->CR2 |= TIM_CR2_CCUS;
+ }
+ else
+ {
+ /* Reset the COM Bit */
+ TIMx->CR2 &= (uint16_t)~((uint16_t)TIM_CR2_CCUS);
+ }
+}
+
+/**
+ * @brief Selects the TIMx peripheral Capture Compare DMA source.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 15, 16 or 17 to select
+ * the TIM peripheral.
+ * @param NewState: new state of the Capture Compare DMA source
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectCCDMA(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST4_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Set the CCDS Bit */
+ TIMx->CR2 |= TIM_CR2_CCDS;
+ }
+ else
+ {
+ /* Reset the CCDS Bit */
+ TIMx->CR2 &= (uint16_t)~((uint16_t)TIM_CR2_CCDS);
+ }
+}
+
+/**
+ * @brief Sets or Resets the TIM peripheral Capture Compare Preload Control bit.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8 or 15
+ * to select the TIMx peripheral
+ * @param NewState: new state of the Capture Compare Preload Control bit
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_CCPreloadControl(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST5_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Set the CCPC Bit */
+ TIMx->CR2 |= TIM_CR2_CCPC;
+ }
+ else
+ {
+ /* Reset the CCPC Bit */
+ TIMx->CR2 &= (uint16_t)~((uint16_t)TIM_CR2_CCPC);
+ }
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR1.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC1PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint16_t tmpccmr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+ tmpccmr1 = TIMx->CCMR1;
+ /* Reset the OC1PE Bit */
+ tmpccmr1 &= (uint16_t)~((uint16_t)TIM_CCMR1_OC1PE);
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr1 |= TIM_OCPreload;
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR2.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select
+ * the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC2PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint16_t tmpccmr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+ tmpccmr1 = TIMx->CCMR1;
+ /* Reset the OC2PE Bit */
+ tmpccmr1 &= (uint16_t)~((uint16_t)TIM_CCMR1_OC2PE);
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr1 |= (uint16_t)(TIM_OCPreload << 8);
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR3.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC3PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint16_t tmpccmr2 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+ tmpccmr2 = TIMx->CCMR2;
+ /* Reset the OC3PE Bit */
+ tmpccmr2 &= (uint16_t)~((uint16_t)TIM_CCMR2_OC3PE);
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr2 |= TIM_OCPreload;
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Enables or disables the TIMx peripheral Preload register on CCR4.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCPreload: new state of the TIMx peripheral Preload register
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPreload_Enable
+ * @arg TIM_OCPreload_Disable
+ * @retval None
+ */
+void TIM_OC4PreloadConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPreload)
+{
+ uint16_t tmpccmr2 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCPRELOAD_STATE(TIM_OCPreload));
+ tmpccmr2 = TIMx->CCMR2;
+ /* Reset the OC4PE Bit */
+ tmpccmr2 &= (uint16_t)~((uint16_t)TIM_CCMR2_OC4PE);
+ /* Enable or Disable the Output Compare Preload feature */
+ tmpccmr2 |= (uint16_t)(TIM_OCPreload << 8);
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Configures the TIMx Output Compare 1 Fast feature.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_OCFast: new state of the Output Compare Fast Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCFast_Enable: TIM output compare fast enable
+ * @arg TIM_OCFast_Disable: TIM output compare fast disable
+ * @retval None
+ */
+void TIM_OC1FastConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCFast)
+{
+ uint16_t tmpccmr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_OCFAST_STATE(TIM_OCFast));
+ /* Get the TIMx CCMR1 register value */
+ tmpccmr1 = TIMx->CCMR1;
+ /* Reset the OC1FE Bit */
+ tmpccmr1 &= (uint16_t)~((uint16_t)TIM_CCMR1_OC1FE);
+ /* Enable or Disable the Output Compare Fast Bit */
+ tmpccmr1 |= TIM_OCFast;
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Configures the TIMx Output Compare 2 Fast feature.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select
+ * the TIM peripheral.
+ * @param TIM_OCFast: new state of the Output Compare Fast Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCFast_Enable: TIM output compare fast enable
+ * @arg TIM_OCFast_Disable: TIM output compare fast disable
+ * @retval None
+ */
+void TIM_OC2FastConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCFast)
+{
+ uint16_t tmpccmr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_OCFAST_STATE(TIM_OCFast));
+ /* Get the TIMx CCMR1 register value */
+ tmpccmr1 = TIMx->CCMR1;
+ /* Reset the OC2FE Bit */
+ tmpccmr1 &= (uint16_t)~((uint16_t)TIM_CCMR1_OC2FE);
+ /* Enable or Disable the Output Compare Fast Bit */
+ tmpccmr1 |= (uint16_t)(TIM_OCFast << 8);
+ /* Write to TIMx CCMR1 */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Configures the TIMx Output Compare 3 Fast feature.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCFast: new state of the Output Compare Fast Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCFast_Enable: TIM output compare fast enable
+ * @arg TIM_OCFast_Disable: TIM output compare fast disable
+ * @retval None
+ */
+void TIM_OC3FastConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCFast)
+{
+ uint16_t tmpccmr2 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCFAST_STATE(TIM_OCFast));
+ /* Get the TIMx CCMR2 register value */
+ tmpccmr2 = TIMx->CCMR2;
+ /* Reset the OC3FE Bit */
+ tmpccmr2 &= (uint16_t)~((uint16_t)TIM_CCMR2_OC3FE);
+ /* Enable or Disable the Output Compare Fast Bit */
+ tmpccmr2 |= TIM_OCFast;
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Configures the TIMx Output Compare 4 Fast feature.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCFast: new state of the Output Compare Fast Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCFast_Enable: TIM output compare fast enable
+ * @arg TIM_OCFast_Disable: TIM output compare fast disable
+ * @retval None
+ */
+void TIM_OC4FastConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCFast)
+{
+ uint16_t tmpccmr2 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCFAST_STATE(TIM_OCFast));
+ /* Get the TIMx CCMR2 register value */
+ tmpccmr2 = TIMx->CCMR2;
+ /* Reset the OC4FE Bit */
+ tmpccmr2 &= (uint16_t)~((uint16_t)TIM_CCMR2_OC4FE);
+ /* Enable or Disable the Output Compare Fast Bit */
+ tmpccmr2 |= (uint16_t)(TIM_OCFast << 8);
+ /* Write to TIMx CCMR2 */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF1 signal on an external event
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC1Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint16_t tmpccmr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+
+ tmpccmr1 = TIMx->CCMR1;
+
+ /* Reset the OC1CE Bit */
+ tmpccmr1 &= (uint16_t)~((uint16_t)TIM_CCMR1_OC1CE);
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr1 |= TIM_OCClear;
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF2 signal on an external event
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC2Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint16_t tmpccmr1 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+ tmpccmr1 = TIMx->CCMR1;
+ /* Reset the OC2CE Bit */
+ tmpccmr1 &= (uint16_t)~((uint16_t)TIM_CCMR1_OC2CE);
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr1 |= (uint16_t)(TIM_OCClear << 8);
+ /* Write to TIMx CCMR1 register */
+ TIMx->CCMR1 = tmpccmr1;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF3 signal on an external event
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC3Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint16_t tmpccmr2 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+ tmpccmr2 = TIMx->CCMR2;
+ /* Reset the OC3CE Bit */
+ tmpccmr2 &= (uint16_t)~((uint16_t)TIM_CCMR2_OC3CE);
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr2 |= TIM_OCClear;
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Clears or safeguards the OCREF4 signal on an external event
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCClear: new state of the Output Compare Clear Enable Bit.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCClear_Enable: TIM Output clear enable
+ * @arg TIM_OCClear_Disable: TIM Output clear disable
+ * @retval None
+ */
+void TIM_ClearOC4Ref(TIM_TypeDef* TIMx, uint16_t TIM_OCClear)
+{
+ uint16_t tmpccmr2 = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OCCLEAR_STATE(TIM_OCClear));
+ tmpccmr2 = TIMx->CCMR2;
+ /* Reset the OC4CE Bit */
+ tmpccmr2 &= (uint16_t)~((uint16_t)TIM_CCMR2_OC4CE);
+ /* Enable or Disable the Output Compare Clear Bit */
+ tmpccmr2 |= (uint16_t)(TIM_OCClear << 8);
+ /* Write to TIMx CCMR2 register */
+ TIMx->CCMR2 = tmpccmr2;
+}
+
+/**
+ * @brief Configures the TIMx channel 1 polarity.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC1 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC1PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint16_t tmpccer = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+ tmpccer = TIMx->CCER;
+ /* Set or Reset the CC1P Bit */
+ tmpccer &= (uint16_t)~((uint16_t)TIM_CCER_CC1P);
+ tmpccer |= TIM_OCPolarity;
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx Channel 1N polarity.
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_OCNPolarity: specifies the OC1N Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCNPolarity_High: Output Compare active high
+ * @arg TIM_OCNPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC1NPolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCNPolarity)
+{
+ uint16_t tmpccer = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCNPolarity));
+
+ tmpccer = TIMx->CCER;
+ /* Set or Reset the CC1NP Bit */
+ tmpccer &= (uint16_t)~((uint16_t)TIM_CCER_CC1NP);
+ tmpccer |= TIM_OCNPolarity;
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx channel 2 polarity.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC2 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC2PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint16_t tmpccer = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+ tmpccer = TIMx->CCER;
+ /* Set or Reset the CC2P Bit */
+ tmpccer &= (uint16_t)~((uint16_t)TIM_CCER_CC2P);
+ tmpccer |= (uint16_t)(TIM_OCPolarity << 4);
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx Channel 2N polarity.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCNPolarity: specifies the OC2N Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCNPolarity_High: Output Compare active high
+ * @arg TIM_OCNPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC2NPolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCNPolarity)
+{
+ uint16_t tmpccer = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCNPolarity));
+
+ tmpccer = TIMx->CCER;
+ /* Set or Reset the CC2NP Bit */
+ tmpccer &= (uint16_t)~((uint16_t)TIM_CCER_CC2NP);
+ tmpccer |= (uint16_t)(TIM_OCNPolarity << 4);
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx channel 3 polarity.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC3 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC3PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint16_t tmpccer = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+ tmpccer = TIMx->CCER;
+ /* Set or Reset the CC3P Bit */
+ tmpccer &= (uint16_t)~((uint16_t)TIM_CCER_CC3P);
+ tmpccer |= (uint16_t)(TIM_OCPolarity << 8);
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx Channel 3N polarity.
+ * @param TIMx: where x can be 1 or 8 to select the TIM peripheral.
+ * @param TIM_OCNPolarity: specifies the OC3N Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCNPolarity_High: Output Compare active high
+ * @arg TIM_OCNPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC3NPolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCNPolarity)
+{
+ uint16_t tmpccer = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST1_PERIPH(TIMx));
+ assert_param(IS_TIM_OCN_POLARITY(TIM_OCNPolarity));
+
+ tmpccer = TIMx->CCER;
+ /* Set or Reset the CC3NP Bit */
+ tmpccer &= (uint16_t)~((uint16_t)TIM_CCER_CC3NP);
+ tmpccer |= (uint16_t)(TIM_OCNPolarity << 8);
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configures the TIMx channel 4 polarity.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_OCPolarity: specifies the OC4 Polarity
+ * This parameter can be one of the following values:
+ * @arg TIM_OCPolarity_High: Output Compare active high
+ * @arg TIM_OCPolarity_Low: Output Compare active low
+ * @retval None
+ */
+void TIM_OC4PolarityConfig(TIM_TypeDef* TIMx, uint16_t TIM_OCPolarity)
+{
+ uint16_t tmpccer = 0;
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_OC_POLARITY(TIM_OCPolarity));
+ tmpccer = TIMx->CCER;
+ /* Set or Reset the CC4P Bit */
+ tmpccer &= (uint16_t)~((uint16_t)TIM_CCER_CC4P);
+ tmpccer |= (uint16_t)(TIM_OCPolarity << 12);
+ /* Write to TIMx CCER register */
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Enables or disables the TIM Capture Compare Channel x.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_Channel: specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_Channel_1: TIM Channel 1
+ * @arg TIM_Channel_2: TIM Channel 2
+ * @arg TIM_Channel_3: TIM Channel 3
+ * @arg TIM_Channel_4: TIM Channel 4
+ * @param TIM_CCx: specifies the TIM Channel CCxE bit new state.
+ * This parameter can be: TIM_CCx_Enable or TIM_CCx_Disable.
+ * @retval None
+ */
+void TIM_CCxCmd(TIM_TypeDef* TIMx, uint16_t TIM_Channel, uint16_t TIM_CCx)
+{
+ uint16_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_CHANNEL(TIM_Channel));
+ assert_param(IS_TIM_CCX(TIM_CCx));
+
+ tmp = CCER_CCE_Set << TIM_Channel;
+
+ /* Reset the CCxE Bit */
+ TIMx->CCER &= (uint16_t)~ tmp;
+
+ /* Set or reset the CCxE Bit */
+ TIMx->CCER |= (uint16_t)(TIM_CCx << TIM_Channel);
+}
+
+/**
+ * @brief Enables or disables the TIM Capture Compare Channel xN.
+ * @param TIMx: where x can be 1, 8, 15, 16 or 17 to select the TIM peripheral.
+ * @param TIM_Channel: specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_Channel_1: TIM Channel 1
+ * @arg TIM_Channel_2: TIM Channel 2
+ * @arg TIM_Channel_3: TIM Channel 3
+ * @param TIM_CCxN: specifies the TIM Channel CCxNE bit new state.
+ * This parameter can be: TIM_CCxN_Enable or TIM_CCxN_Disable.
+ * @retval None
+ */
+void TIM_CCxNCmd(TIM_TypeDef* TIMx, uint16_t TIM_Channel, uint16_t TIM_CCxN)
+{
+ uint16_t tmp = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST2_PERIPH(TIMx));
+ assert_param(IS_TIM_COMPLEMENTARY_CHANNEL(TIM_Channel));
+ assert_param(IS_TIM_CCXN(TIM_CCxN));
+
+ tmp = CCER_CCNE_Set << TIM_Channel;
+
+ /* Reset the CCxNE Bit */
+ TIMx->CCER &= (uint16_t) ~tmp;
+
+ /* Set or reset the CCxNE Bit */
+ TIMx->CCER |= (uint16_t)(TIM_CCxN << TIM_Channel);
+}
+
+/**
+ * @brief Selects the TIM Output Compare Mode.
+ * @note This function disables the selected channel before changing the Output
+ * Compare Mode.
+ * User has to enable this channel using TIM_CCxCmd and TIM_CCxNCmd functions.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_Channel: specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_Channel_1: TIM Channel 1
+ * @arg TIM_Channel_2: TIM Channel 2
+ * @arg TIM_Channel_3: TIM Channel 3
+ * @arg TIM_Channel_4: TIM Channel 4
+ * @param TIM_OCMode: specifies the TIM Output Compare Mode.
+ * This parameter can be one of the following values:
+ * @arg TIM_OCMode_Timing
+ * @arg TIM_OCMode_Active
+ * @arg TIM_OCMode_Toggle
+ * @arg TIM_OCMode_PWM1
+ * @arg TIM_OCMode_PWM2
+ * @arg TIM_ForcedAction_Active
+ * @arg TIM_ForcedAction_InActive
+ * @retval None
+ */
+void TIM_SelectOCxM(TIM_TypeDef* TIMx, uint16_t TIM_Channel, uint16_t TIM_OCMode)
+{
+ uint32_t tmp = 0;
+ uint16_t tmp1 = 0;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_CHANNEL(TIM_Channel));
+ assert_param(IS_TIM_OCM(TIM_OCMode));
+
+ tmp = (uint32_t) TIMx;
+ tmp += CCMR_Offset;
+
+ tmp1 = CCER_CCE_Set << (uint16_t)TIM_Channel;
+
+ /* Disable the Channel: Reset the CCxE Bit */
+ TIMx->CCER &= (uint16_t) ~tmp1;
+
+ if((TIM_Channel == TIM_Channel_1) ||(TIM_Channel == TIM_Channel_3))
+ {
+ tmp += (TIM_Channel>>1);
+
+ /* Reset the OCxM bits in the CCMRx register */
+ *(__IO uint32_t *) tmp &= (uint32_t)~((uint32_t)TIM_CCMR1_OC1M);
+
+ /* Configure the OCxM bits in the CCMRx register */
+ *(__IO uint32_t *) tmp |= TIM_OCMode;
+ }
+ else
+ {
+ tmp += (uint16_t)(TIM_Channel - (uint16_t)4)>> (uint16_t)1;
+
+ /* Reset the OCxM bits in the CCMRx register */
+ *(__IO uint32_t *) tmp &= (uint32_t)~((uint32_t)TIM_CCMR1_OC2M);
+
+ /* Configure the OCxM bits in the CCMRx register */
+ *(__IO uint32_t *) tmp |= (uint16_t)(TIM_OCMode << 8);
+ }
+}
+
+/**
+ * @brief Enables or Disables the TIMx Update event.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param NewState: new state of the TIMx UDIS bit
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_UpdateDisableConfig(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Set the Update Disable Bit */
+ TIMx->CR1 |= TIM_CR1_UDIS;
+ }
+ else
+ {
+ /* Reset the Update Disable Bit */
+ TIMx->CR1 &= (uint16_t)~((uint16_t)TIM_CR1_UDIS);
+ }
+}
+
+/**
+ * @brief Configures the TIMx Update Request Interrupt source.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param TIM_UpdateSource: specifies the Update source.
+ * This parameter can be one of the following values:
+ * @arg TIM_UpdateSource_Regular: Source of update is the counter overflow/underflow
+ or the setting of UG bit, or an update generation
+ through the slave mode controller.
+ * @arg TIM_UpdateSource_Global: Source of update is counter overflow/underflow.
+ * @retval None
+ */
+void TIM_UpdateRequestConfig(TIM_TypeDef* TIMx, uint16_t TIM_UpdateSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_UPDATE_SOURCE(TIM_UpdateSource));
+ if (TIM_UpdateSource != TIM_UpdateSource_Global)
+ {
+ /* Set the URS Bit */
+ TIMx->CR1 |= TIM_CR1_URS;
+ }
+ else
+ {
+ /* Reset the URS Bit */
+ TIMx->CR1 &= (uint16_t)~((uint16_t)TIM_CR1_URS);
+ }
+}
+
+/**
+ * @brief Enables or disables the TIMx's Hall sensor interface.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param NewState: new state of the TIMx Hall sensor interface.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void TIM_SelectHallSensor(TIM_TypeDef* TIMx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Set the TI1S Bit */
+ TIMx->CR2 |= TIM_CR2_TI1S;
+ }
+ else
+ {
+ /* Reset the TI1S Bit */
+ TIMx->CR2 &= (uint16_t)~((uint16_t)TIM_CR2_TI1S);
+ }
+}
+
+/**
+ * @brief Selects the TIMx's One Pulse Mode.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param TIM_OPMode: specifies the OPM Mode to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_OPMode_Single
+ * @arg TIM_OPMode_Repetitive
+ * @retval None
+ */
+void TIM_SelectOnePulseMode(TIM_TypeDef* TIMx, uint16_t TIM_OPMode)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_OPM_MODE(TIM_OPMode));
+ /* Reset the OPM Bit */
+ TIMx->CR1 &= (uint16_t)~((uint16_t)TIM_CR1_OPM);
+ /* Configure the OPM Mode */
+ TIMx->CR1 |= TIM_OPMode;
+}
+
+/**
+ * @brief Selects the TIMx Trigger Output Mode.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 6, 7, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_TRGOSource: specifies the Trigger Output source.
+ * This paramter can be one of the following values:
+ *
+ * - For all TIMx
+ * @arg TIM_TRGOSource_Reset: The UG bit in the TIM_EGR register is used as the trigger output (TRGO).
+ * @arg TIM_TRGOSource_Enable: The Counter Enable CEN is used as the trigger output (TRGO).
+ * @arg TIM_TRGOSource_Update: The update event is selected as the trigger output (TRGO).
+ *
+ * - For all TIMx except TIM6 and TIM7
+ * @arg TIM_TRGOSource_OC1: The trigger output sends a positive pulse when the CC1IF flag
+ * is to be set, as soon as a capture or compare match occurs (TRGO).
+ * @arg TIM_TRGOSource_OC1Ref: OC1REF signal is used as the trigger output (TRGO).
+ * @arg TIM_TRGOSource_OC2Ref: OC2REF signal is used as the trigger output (TRGO).
+ * @arg TIM_TRGOSource_OC3Ref: OC3REF signal is used as the trigger output (TRGO).
+ * @arg TIM_TRGOSource_OC4Ref: OC4REF signal is used as the trigger output (TRGO).
+ *
+ * @retval None
+ */
+void TIM_SelectOutputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_TRGOSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST7_PERIPH(TIMx));
+ assert_param(IS_TIM_TRGO_SOURCE(TIM_TRGOSource));
+ /* Reset the MMS Bits */
+ TIMx->CR2 &= (uint16_t)~((uint16_t)TIM_CR2_MMS);
+ /* Select the TRGO source */
+ TIMx->CR2 |= TIM_TRGOSource;
+}
+
+/**
+ * @brief Selects the TIMx Slave Mode.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_SlaveMode: specifies the Timer Slave Mode.
+ * This parameter can be one of the following values:
+ * @arg TIM_SlaveMode_Reset: Rising edge of the selected trigger signal (TRGI) re-initializes
+ * the counter and triggers an update of the registers.
+ * @arg TIM_SlaveMode_Gated: The counter clock is enabled when the trigger signal (TRGI) is high.
+ * @arg TIM_SlaveMode_Trigger: The counter starts at a rising edge of the trigger TRGI.
+ * @arg TIM_SlaveMode_External1: Rising edges of the selected trigger (TRGI) clock the counter.
+ * @retval None
+ */
+void TIM_SelectSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_SlaveMode)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_SLAVE_MODE(TIM_SlaveMode));
+ /* Reset the SMS Bits */
+ TIMx->SMCR &= (uint16_t)~((uint16_t)TIM_SMCR_SMS);
+ /* Select the Slave Mode */
+ TIMx->SMCR |= TIM_SlaveMode;
+}
+
+/**
+ * @brief Sets or Resets the TIMx Master/Slave Mode.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_MasterSlaveMode: specifies the Timer Master Slave Mode.
+ * This parameter can be one of the following values:
+ * @arg TIM_MasterSlaveMode_Enable: synchronization between the current timer
+ * and its slaves (through TRGO).
+ * @arg TIM_MasterSlaveMode_Disable: No action
+ * @retval None
+ */
+void TIM_SelectMasterSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_MasterSlaveMode)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_MSM_STATE(TIM_MasterSlaveMode));
+ /* Reset the MSM Bit */
+ TIMx->SMCR &= (uint16_t)~((uint16_t)TIM_SMCR_MSM);
+
+ /* Set or Reset the MSM Bit */
+ TIMx->SMCR |= TIM_MasterSlaveMode;
+}
+
+/**
+ * @brief Sets the TIMx Counter Register value
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param Counter: specifies the Counter register new value.
+ * @retval None
+ */
+void TIM_SetCounter(TIM_TypeDef* TIMx, uint16_t Counter)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ /* Set the Counter Register value */
+ TIMx->CNT = Counter;
+}
+
+/**
+ * @brief Sets the TIMx Autoreload Register value
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param Autoreload: specifies the Autoreload register new value.
+ * @retval None
+ */
+void TIM_SetAutoreload(TIM_TypeDef* TIMx, uint16_t Autoreload)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ /* Set the Autoreload Register value */
+ TIMx->ARR = Autoreload;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare1 Register value
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param Compare1: specifies the Capture Compare1 register new value.
+ * @retval None
+ */
+void TIM_SetCompare1(TIM_TypeDef* TIMx, uint16_t Compare1)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ /* Set the Capture Compare1 Register value */
+ TIMx->CCR1 = Compare1;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare2 Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param Compare2: specifies the Capture Compare2 register new value.
+ * @retval None
+ */
+void TIM_SetCompare2(TIM_TypeDef* TIMx, uint16_t Compare2)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ /* Set the Capture Compare2 Register value */
+ TIMx->CCR2 = Compare2;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare3 Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param Compare3: specifies the Capture Compare3 register new value.
+ * @retval None
+ */
+void TIM_SetCompare3(TIM_TypeDef* TIMx, uint16_t Compare3)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ /* Set the Capture Compare3 Register value */
+ TIMx->CCR3 = Compare3;
+}
+
+/**
+ * @brief Sets the TIMx Capture Compare4 Register value
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param Compare4: specifies the Capture Compare4 register new value.
+ * @retval None
+ */
+void TIM_SetCompare4(TIM_TypeDef* TIMx, uint16_t Compare4)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ /* Set the Capture Compare4 Register value */
+ TIMx->CCR4 = Compare4;
+}
+
+/**
+ * @brief Sets the TIMx Input Capture 1 prescaler.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_ICPSC: specifies the Input Capture1 prescaler new value.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPSC_DIV1: no prescaler
+ * @arg TIM_ICPSC_DIV2: capture is done once every 2 events
+ * @arg TIM_ICPSC_DIV4: capture is done once every 4 events
+ * @arg TIM_ICPSC_DIV8: capture is done once every 8 events
+ * @retval None
+ */
+void TIM_SetIC1Prescaler(TIM_TypeDef* TIMx, uint16_t TIM_ICPSC)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICPSC));
+ /* Reset the IC1PSC Bits */
+ TIMx->CCMR1 &= (uint16_t)~((uint16_t)TIM_CCMR1_IC1PSC);
+ /* Set the IC1PSC value */
+ TIMx->CCMR1 |= TIM_ICPSC;
+}
+
+/**
+ * @brief Sets the TIMx Input Capture 2 prescaler.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_ICPSC: specifies the Input Capture2 prescaler new value.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPSC_DIV1: no prescaler
+ * @arg TIM_ICPSC_DIV2: capture is done once every 2 events
+ * @arg TIM_ICPSC_DIV4: capture is done once every 4 events
+ * @arg TIM_ICPSC_DIV8: capture is done once every 8 events
+ * @retval None
+ */
+void TIM_SetIC2Prescaler(TIM_TypeDef* TIMx, uint16_t TIM_ICPSC)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICPSC));
+ /* Reset the IC2PSC Bits */
+ TIMx->CCMR1 &= (uint16_t)~((uint16_t)TIM_CCMR1_IC2PSC);
+ /* Set the IC2PSC value */
+ TIMx->CCMR1 |= (uint16_t)(TIM_ICPSC << 8);
+}
+
+/**
+ * @brief Sets the TIMx Input Capture 3 prescaler.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ICPSC: specifies the Input Capture3 prescaler new value.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPSC_DIV1: no prescaler
+ * @arg TIM_ICPSC_DIV2: capture is done once every 2 events
+ * @arg TIM_ICPSC_DIV4: capture is done once every 4 events
+ * @arg TIM_ICPSC_DIV8: capture is done once every 8 events
+ * @retval None
+ */
+void TIM_SetIC3Prescaler(TIM_TypeDef* TIMx, uint16_t TIM_ICPSC)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICPSC));
+ /* Reset the IC3PSC Bits */
+ TIMx->CCMR2 &= (uint16_t)~((uint16_t)TIM_CCMR2_IC3PSC);
+ /* Set the IC3PSC value */
+ TIMx->CCMR2 |= TIM_ICPSC;
+}
+
+/**
+ * @brief Sets the TIMx Input Capture 4 prescaler.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ICPSC: specifies the Input Capture4 prescaler new value.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPSC_DIV1: no prescaler
+ * @arg TIM_ICPSC_DIV2: capture is done once every 2 events
+ * @arg TIM_ICPSC_DIV4: capture is done once every 4 events
+ * @arg TIM_ICPSC_DIV8: capture is done once every 8 events
+ * @retval None
+ */
+void TIM_SetIC4Prescaler(TIM_TypeDef* TIMx, uint16_t TIM_ICPSC)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ assert_param(IS_TIM_IC_PRESCALER(TIM_ICPSC));
+ /* Reset the IC4PSC Bits */
+ TIMx->CCMR2 &= (uint16_t)~((uint16_t)TIM_CCMR2_IC4PSC);
+ /* Set the IC4PSC value */
+ TIMx->CCMR2 |= (uint16_t)(TIM_ICPSC << 8);
+}
+
+/**
+ * @brief Sets the TIMx Clock Division value.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select
+ * the TIM peripheral.
+ * @param TIM_CKD: specifies the clock division value.
+ * This parameter can be one of the following value:
+ * @arg TIM_CKD_DIV1: TDTS = Tck_tim
+ * @arg TIM_CKD_DIV2: TDTS = 2*Tck_tim
+ * @arg TIM_CKD_DIV4: TDTS = 4*Tck_tim
+ * @retval None
+ */
+void TIM_SetClockDivision(TIM_TypeDef* TIMx, uint16_t TIM_CKD)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ assert_param(IS_TIM_CKD_DIV(TIM_CKD));
+ /* Reset the CKD Bits */
+ TIMx->CR1 &= (uint16_t)~((uint16_t)TIM_CR1_CKD);
+ /* Set the CKD value */
+ TIMx->CR1 |= TIM_CKD;
+}
+
+/**
+ * @brief Gets the TIMx Input Capture 1 value.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @retval Capture Compare 1 Register value.
+ */
+uint16_t TIM_GetCapture1(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST8_PERIPH(TIMx));
+ /* Get the Capture 1 Register value */
+ return TIMx->CCR1;
+}
+
+/**
+ * @brief Gets the TIMx Input Capture 2 value.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @retval Capture Compare 2 Register value.
+ */
+uint16_t TIM_GetCapture2(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST6_PERIPH(TIMx));
+ /* Get the Capture 2 Register value */
+ return TIMx->CCR2;
+}
+
+/**
+ * @brief Gets the TIMx Input Capture 3 value.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @retval Capture Compare 3 Register value.
+ */
+uint16_t TIM_GetCapture3(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ /* Get the Capture 3 Register value */
+ return TIMx->CCR3;
+}
+
+/**
+ * @brief Gets the TIMx Input Capture 4 value.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @retval Capture Compare 4 Register value.
+ */
+uint16_t TIM_GetCapture4(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_LIST3_PERIPH(TIMx));
+ /* Get the Capture 4 Register value */
+ return TIMx->CCR4;
+}
+
+/**
+ * @brief Gets the TIMx Counter value.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @retval Counter Register value.
+ */
+uint16_t TIM_GetCounter(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ /* Get the Counter Register value */
+ return TIMx->CNT;
+}
+
+/**
+ * @brief Gets the TIMx Prescaler value.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @retval Prescaler Register value.
+ */
+uint16_t TIM_GetPrescaler(TIM_TypeDef* TIMx)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ /* Get the Prescaler Register value */
+ return TIMx->PSC;
+}
+
+/**
+ * @brief Checks whether the specified TIM flag is set or not.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param TIM_FLAG: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg TIM_FLAG_Update: TIM update Flag
+ * @arg TIM_FLAG_CC1: TIM Capture Compare 1 Flag
+ * @arg TIM_FLAG_CC2: TIM Capture Compare 2 Flag
+ * @arg TIM_FLAG_CC3: TIM Capture Compare 3 Flag
+ * @arg TIM_FLAG_CC4: TIM Capture Compare 4 Flag
+ * @arg TIM_FLAG_COM: TIM Commutation Flag
+ * @arg TIM_FLAG_Trigger: TIM Trigger Flag
+ * @arg TIM_FLAG_Break: TIM Break Flag
+ * @arg TIM_FLAG_CC1OF: TIM Capture Compare 1 overcapture Flag
+ * @arg TIM_FLAG_CC2OF: TIM Capture Compare 2 overcapture Flag
+ * @arg TIM_FLAG_CC3OF: TIM Capture Compare 3 overcapture Flag
+ * @arg TIM_FLAG_CC4OF: TIM Capture Compare 4 overcapture Flag
+ * @note
+ * - TIM6 and TIM7 can have only one update flag.
+ * - TIM9, TIM12 and TIM15 can have only TIM_FLAG_Update, TIM_FLAG_CC1,
+ * TIM_FLAG_CC2 or TIM_FLAG_Trigger.
+ * - TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_FLAG_Update or TIM_FLAG_CC1.
+ * - TIM_FLAG_Break is used only with TIM1, TIM8 and TIM15.
+ * - TIM_FLAG_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.
+ * @retval The new state of TIM_FLAG (SET or RESET).
+ */
+FlagStatus TIM_GetFlagStatus(TIM_TypeDef* TIMx, uint16_t TIM_FLAG)
+{
+ ITStatus bitstatus = RESET;
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_GET_FLAG(TIM_FLAG));
+
+ if ((TIMx->SR & TIM_FLAG) != (uint16_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the TIMx's pending flags.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param TIM_FLAG: specifies the flag bit to clear.
+ * This parameter can be any combination of the following values:
+ * @arg TIM_FLAG_Update: TIM update Flag
+ * @arg TIM_FLAG_CC1: TIM Capture Compare 1 Flag
+ * @arg TIM_FLAG_CC2: TIM Capture Compare 2 Flag
+ * @arg TIM_FLAG_CC3: TIM Capture Compare 3 Flag
+ * @arg TIM_FLAG_CC4: TIM Capture Compare 4 Flag
+ * @arg TIM_FLAG_COM: TIM Commutation Flag
+ * @arg TIM_FLAG_Trigger: TIM Trigger Flag
+ * @arg TIM_FLAG_Break: TIM Break Flag
+ * @arg TIM_FLAG_CC1OF: TIM Capture Compare 1 overcapture Flag
+ * @arg TIM_FLAG_CC2OF: TIM Capture Compare 2 overcapture Flag
+ * @arg TIM_FLAG_CC3OF: TIM Capture Compare 3 overcapture Flag
+ * @arg TIM_FLAG_CC4OF: TIM Capture Compare 4 overcapture Flag
+ * @note
+ * - TIM6 and TIM7 can have only one update flag.
+ * - TIM9, TIM12 and TIM15 can have only TIM_FLAG_Update, TIM_FLAG_CC1,
+ * TIM_FLAG_CC2 or TIM_FLAG_Trigger.
+ * - TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_FLAG_Update or TIM_FLAG_CC1.
+ * - TIM_FLAG_Break is used only with TIM1, TIM8 and TIM15.
+ * - TIM_FLAG_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.
+ * @retval None
+ */
+void TIM_ClearFlag(TIM_TypeDef* TIMx, uint16_t TIM_FLAG)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_CLEAR_FLAG(TIM_FLAG));
+
+ /* Clear the flags */
+ TIMx->SR = (uint16_t)~TIM_FLAG;
+}
+
+/**
+ * @brief Checks whether the TIM interrupt has occurred or not.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param TIM_IT: specifies the TIM interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg TIM_IT_Update: TIM update Interrupt source
+ * @arg TIM_IT_CC1: TIM Capture Compare 1 Interrupt source
+ * @arg TIM_IT_CC2: TIM Capture Compare 2 Interrupt source
+ * @arg TIM_IT_CC3: TIM Capture Compare 3 Interrupt source
+ * @arg TIM_IT_CC4: TIM Capture Compare 4 Interrupt source
+ * @arg TIM_IT_COM: TIM Commutation Interrupt source
+ * @arg TIM_IT_Trigger: TIM Trigger Interrupt source
+ * @arg TIM_IT_Break: TIM Break Interrupt source
+ * @note
+ * - TIM6 and TIM7 can generate only an update interrupt.
+ * - TIM9, TIM12 and TIM15 can have only TIM_IT_Update, TIM_IT_CC1,
+ * TIM_IT_CC2 or TIM_IT_Trigger.
+ * - TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_IT_Update or TIM_IT_CC1.
+ * - TIM_IT_Break is used only with TIM1, TIM8 and TIM15.
+ * - TIM_IT_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.
+ * @retval The new state of the TIM_IT(SET or RESET).
+ */
+ITStatus TIM_GetITStatus(TIM_TypeDef* TIMx, uint16_t TIM_IT)
+{
+ ITStatus bitstatus = RESET;
+ uint16_t itstatus = 0x0, itenable = 0x0;
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_GET_IT(TIM_IT));
+
+ itstatus = TIMx->SR & TIM_IT;
+
+ itenable = TIMx->DIER & TIM_IT;
+ if ((itstatus != (uint16_t)RESET) && (itenable != (uint16_t)RESET))
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the TIMx's interrupt pending bits.
+ * @param TIMx: where x can be 1 to 17 to select the TIM peripheral.
+ * @param TIM_IT: specifies the pending bit to clear.
+ * This parameter can be any combination of the following values:
+ * @arg TIM_IT_Update: TIM1 update Interrupt source
+ * @arg TIM_IT_CC1: TIM Capture Compare 1 Interrupt source
+ * @arg TIM_IT_CC2: TIM Capture Compare 2 Interrupt source
+ * @arg TIM_IT_CC3: TIM Capture Compare 3 Interrupt source
+ * @arg TIM_IT_CC4: TIM Capture Compare 4 Interrupt source
+ * @arg TIM_IT_COM: TIM Commutation Interrupt source
+ * @arg TIM_IT_Trigger: TIM Trigger Interrupt source
+ * @arg TIM_IT_Break: TIM Break Interrupt source
+ * @note
+ * - TIM6 and TIM7 can generate only an update interrupt.
+ * - TIM9, TIM12 and TIM15 can have only TIM_IT_Update, TIM_IT_CC1,
+ * TIM_IT_CC2 or TIM_IT_Trigger.
+ * - TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_IT_Update or TIM_IT_CC1.
+ * - TIM_IT_Break is used only with TIM1, TIM8 and TIM15.
+ * - TIM_IT_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.
+ * @retval None
+ */
+void TIM_ClearITPendingBit(TIM_TypeDef* TIMx, uint16_t TIM_IT)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_ALL_PERIPH(TIMx));
+ assert_param(IS_TIM_IT(TIM_IT));
+ /* Clear the IT pending Bit */
+ TIMx->SR = (uint16_t)~TIM_IT;
+}
+
+/**
+ * @brief Configure the TI1 as Input.
+ * @param TIMx: where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
+ * @param TIM_ICPolarity : The Input Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @param TIM_ICSelection: specifies the input to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICSelection_DirectTI: TIM Input 1 is selected to be connected to IC1.
+ * @arg TIM_ICSelection_IndirectTI: TIM Input 1 is selected to be connected to IC2.
+ * @arg TIM_ICSelection_TRC: TIM Input 1 is selected to be connected to TRC.
+ * @param TIM_ICFilter: Specifies the Input Capture Filter.
+ * This parameter must be a value between 0x00 and 0x0F.
+ * @retval None
+ */
+static void TI1_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter)
+{
+ uint16_t tmpccmr1 = 0, tmpccer = 0;
+ /* Disable the Channel 1: Reset the CC1E Bit */
+ TIMx->CCER &= (uint16_t)~((uint16_t)TIM_CCER_CC1E);
+ tmpccmr1 = TIMx->CCMR1;
+ tmpccer = TIMx->CCER;
+ /* Select the Input and set the filter */
+ tmpccmr1 &= (uint16_t)(((uint16_t)~((uint16_t)TIM_CCMR1_CC1S)) & ((uint16_t)~((uint16_t)TIM_CCMR1_IC1F)));
+ tmpccmr1 |= (uint16_t)(TIM_ICSelection | (uint16_t)(TIM_ICFilter << (uint16_t)4));
+
+ if((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) ||
+ (TIMx == TIM4) ||(TIMx == TIM5))
+ {
+ /* Select the Polarity and set the CC1E Bit */
+ tmpccer &= (uint16_t)~((uint16_t)(TIM_CCER_CC1P));
+ tmpccer |= (uint16_t)(TIM_ICPolarity | (uint16_t)TIM_CCER_CC1E);
+ }
+ else
+ {
+ /* Select the Polarity and set the CC1E Bit */
+ tmpccer &= (uint16_t)~((uint16_t)(TIM_CCER_CC1P | TIM_CCER_CC1NP));
+ tmpccer |= (uint16_t)(TIM_ICPolarity | (uint16_t)TIM_CCER_CC1E);
+ }
+
+ /* Write to TIMx CCMR1 and CCER registers */
+ TIMx->CCMR1 = tmpccmr1;
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configure the TI2 as Input.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
+ * @param TIM_ICPolarity : The Input Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @param TIM_ICSelection: specifies the input to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICSelection_DirectTI: TIM Input 2 is selected to be connected to IC2.
+ * @arg TIM_ICSelection_IndirectTI: TIM Input 2 is selected to be connected to IC1.
+ * @arg TIM_ICSelection_TRC: TIM Input 2 is selected to be connected to TRC.
+ * @param TIM_ICFilter: Specifies the Input Capture Filter.
+ * This parameter must be a value between 0x00 and 0x0F.
+ * @retval None
+ */
+static void TI2_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter)
+{
+ uint16_t tmpccmr1 = 0, tmpccer = 0, tmp = 0;
+ /* Disable the Channel 2: Reset the CC2E Bit */
+ TIMx->CCER &= (uint16_t)~((uint16_t)TIM_CCER_CC2E);
+ tmpccmr1 = TIMx->CCMR1;
+ tmpccer = TIMx->CCER;
+ tmp = (uint16_t)(TIM_ICPolarity << 4);
+ /* Select the Input and set the filter */
+ tmpccmr1 &= (uint16_t)(((uint16_t)~((uint16_t)TIM_CCMR1_CC2S)) & ((uint16_t)~((uint16_t)TIM_CCMR1_IC2F)));
+ tmpccmr1 |= (uint16_t)(TIM_ICFilter << 12);
+ tmpccmr1 |= (uint16_t)(TIM_ICSelection << 8);
+
+ if((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) ||
+ (TIMx == TIM4) ||(TIMx == TIM5))
+ {
+ /* Select the Polarity and set the CC2E Bit */
+ tmpccer &= (uint16_t)~((uint16_t)(TIM_CCER_CC2P));
+ tmpccer |= (uint16_t)(tmp | (uint16_t)TIM_CCER_CC2E);
+ }
+ else
+ {
+ /* Select the Polarity and set the CC2E Bit */
+ tmpccer &= (uint16_t)~((uint16_t)(TIM_CCER_CC2P | TIM_CCER_CC2NP));
+ tmpccer |= (uint16_t)(TIM_ICPolarity | (uint16_t)TIM_CCER_CC2E);
+ }
+
+ /* Write to TIMx CCMR1 and CCER registers */
+ TIMx->CCMR1 = tmpccmr1 ;
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configure the TI3 as Input.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ICPolarity : The Input Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @param TIM_ICSelection: specifies the input to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICSelection_DirectTI: TIM Input 3 is selected to be connected to IC3.
+ * @arg TIM_ICSelection_IndirectTI: TIM Input 3 is selected to be connected to IC4.
+ * @arg TIM_ICSelection_TRC: TIM Input 3 is selected to be connected to TRC.
+ * @param TIM_ICFilter: Specifies the Input Capture Filter.
+ * This parameter must be a value between 0x00 and 0x0F.
+ * @retval None
+ */
+static void TI3_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter)
+{
+ uint16_t tmpccmr2 = 0, tmpccer = 0, tmp = 0;
+ /* Disable the Channel 3: Reset the CC3E Bit */
+ TIMx->CCER &= (uint16_t)~((uint16_t)TIM_CCER_CC3E);
+ tmpccmr2 = TIMx->CCMR2;
+ tmpccer = TIMx->CCER;
+ tmp = (uint16_t)(TIM_ICPolarity << 8);
+ /* Select the Input and set the filter */
+ tmpccmr2 &= (uint16_t)(((uint16_t)~((uint16_t)TIM_CCMR2_CC3S)) & ((uint16_t)~((uint16_t)TIM_CCMR2_IC3F)));
+ tmpccmr2 |= (uint16_t)(TIM_ICSelection | (uint16_t)(TIM_ICFilter << (uint16_t)4));
+
+ if((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) ||
+ (TIMx == TIM4) ||(TIMx == TIM5))
+ {
+ /* Select the Polarity and set the CC3E Bit */
+ tmpccer &= (uint16_t)~((uint16_t)(TIM_CCER_CC3P));
+ tmpccer |= (uint16_t)(tmp | (uint16_t)TIM_CCER_CC3E);
+ }
+ else
+ {
+ /* Select the Polarity and set the CC3E Bit */
+ tmpccer &= (uint16_t)~((uint16_t)(TIM_CCER_CC3P | TIM_CCER_CC3NP));
+ tmpccer |= (uint16_t)(TIM_ICPolarity | (uint16_t)TIM_CCER_CC3E);
+ }
+
+ /* Write to TIMx CCMR2 and CCER registers */
+ TIMx->CCMR2 = tmpccmr2;
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @brief Configure the TI4 as Input.
+ * @param TIMx: where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
+ * @param TIM_ICPolarity : The Input Polarity.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICPolarity_Rising
+ * @arg TIM_ICPolarity_Falling
+ * @param TIM_ICSelection: specifies the input to be used.
+ * This parameter can be one of the following values:
+ * @arg TIM_ICSelection_DirectTI: TIM Input 4 is selected to be connected to IC4.
+ * @arg TIM_ICSelection_IndirectTI: TIM Input 4 is selected to be connected to IC3.
+ * @arg TIM_ICSelection_TRC: TIM Input 4 is selected to be connected to TRC.
+ * @param TIM_ICFilter: Specifies the Input Capture Filter.
+ * This parameter must be a value between 0x00 and 0x0F.
+ * @retval None
+ */
+static void TI4_Config(TIM_TypeDef* TIMx, uint16_t TIM_ICPolarity, uint16_t TIM_ICSelection,
+ uint16_t TIM_ICFilter)
+{
+ uint16_t tmpccmr2 = 0, tmpccer = 0, tmp = 0;
+
+ /* Disable the Channel 4: Reset the CC4E Bit */
+ TIMx->CCER &= (uint16_t)~((uint16_t)TIM_CCER_CC4E);
+ tmpccmr2 = TIMx->CCMR2;
+ tmpccer = TIMx->CCER;
+ tmp = (uint16_t)(TIM_ICPolarity << 12);
+ /* Select the Input and set the filter */
+ tmpccmr2 &= (uint16_t)((uint16_t)(~(uint16_t)TIM_CCMR2_CC4S) & ((uint16_t)~((uint16_t)TIM_CCMR2_IC4F)));
+ tmpccmr2 |= (uint16_t)(TIM_ICSelection << 8);
+ tmpccmr2 |= (uint16_t)(TIM_ICFilter << 12);
+
+ if((TIMx == TIM1) || (TIMx == TIM8) || (TIMx == TIM2) || (TIMx == TIM3) ||
+ (TIMx == TIM4) ||(TIMx == TIM5))
+ {
+ /* Select the Polarity and set the CC4E Bit */
+ tmpccer &= (uint16_t)~((uint16_t)(TIM_CCER_CC4P));
+ tmpccer |= (uint16_t)(tmp | (uint16_t)TIM_CCER_CC4E);
+ }
+ else
+ {
+ /* Select the Polarity and set the CC4E Bit */
+ tmpccer &= (uint16_t)~((uint16_t)(TIM_CCER_CC3P | TIM_CCER_CC4NP));
+ tmpccer |= (uint16_t)(TIM_ICPolarity | (uint16_t)TIM_CCER_CC4E);
+ }
+ /* Write to TIMx CCMR2 and CCER registers */
+ TIMx->CCMR2 = tmpccmr2;
+ TIMx->CCER = tmpccer;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_usart.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_usart.c
new file mode 100644
index 00000000..a3f16f15
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_usart.c
@@ -0,0 +1,1058 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x_usart.c
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief This file provides all the USART firmware functions.
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_usart.h"
+#include "stm32f10x_rcc.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup USART
+ * @brief USART driver modules
+ * @{
+ */
+
+/** @defgroup USART_Private_TypesDefinitions
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Defines
+ * @{
+ */
+
+#define CR1_UE_Set ((uint16_t)0x2000) /*!< USART Enable Mask */
+#define CR1_UE_Reset ((uint16_t)0xDFFF) /*!< USART Disable Mask */
+
+#define CR1_WAKE_Mask ((uint16_t)0xF7FF) /*!< USART WakeUp Method Mask */
+
+#define CR1_RWU_Set ((uint16_t)0x0002) /*!< USART mute mode Enable Mask */
+#define CR1_RWU_Reset ((uint16_t)0xFFFD) /*!< USART mute mode Enable Mask */
+#define CR1_SBK_Set ((uint16_t)0x0001) /*!< USART Break Character send Mask */
+#define CR1_CLEAR_Mask ((uint16_t)0xE9F3) /*!< USART CR1 Mask */
+#define CR2_Address_Mask ((uint16_t)0xFFF0) /*!< USART address Mask */
+
+#define CR2_LINEN_Set ((uint16_t)0x4000) /*!< USART LIN Enable Mask */
+#define CR2_LINEN_Reset ((uint16_t)0xBFFF) /*!< USART LIN Disable Mask */
+
+#define CR2_LBDL_Mask ((uint16_t)0xFFDF) /*!< USART LIN Break detection Mask */
+#define CR2_STOP_CLEAR_Mask ((uint16_t)0xCFFF) /*!< USART CR2 STOP Bits Mask */
+#define CR2_CLOCK_CLEAR_Mask ((uint16_t)0xF0FF) /*!< USART CR2 Clock Mask */
+
+#define CR3_SCEN_Set ((uint16_t)0x0020) /*!< USART SC Enable Mask */
+#define CR3_SCEN_Reset ((uint16_t)0xFFDF) /*!< USART SC Disable Mask */
+
+#define CR3_NACK_Set ((uint16_t)0x0010) /*!< USART SC NACK Enable Mask */
+#define CR3_NACK_Reset ((uint16_t)0xFFEF) /*!< USART SC NACK Disable Mask */
+
+#define CR3_HDSEL_Set ((uint16_t)0x0008) /*!< USART Half-Duplex Enable Mask */
+#define CR3_HDSEL_Reset ((uint16_t)0xFFF7) /*!< USART Half-Duplex Disable Mask */
+
+#define CR3_IRLP_Mask ((uint16_t)0xFFFB) /*!< USART IrDA LowPower mode Mask */
+#define CR3_CLEAR_Mask ((uint16_t)0xFCFF) /*!< USART CR3 Mask */
+
+#define CR3_IREN_Set ((uint16_t)0x0002) /*!< USART IrDA Enable Mask */
+#define CR3_IREN_Reset ((uint16_t)0xFFFD) /*!< USART IrDA Disable Mask */
+#define GTPR_LSB_Mask ((uint16_t)0x00FF) /*!< Guard Time Register LSB Mask */
+#define GTPR_MSB_Mask ((uint16_t)0xFF00) /*!< Guard Time Register MSB Mask */
+#define IT_Mask ((uint16_t)0x001F) /*!< USART Interrupt Mask */
+
+/* USART OverSampling-8 Mask */
+#define CR1_OVER8_Set ((u16)0x8000) /* USART OVER8 mode Enable Mask */
+#define CR1_OVER8_Reset ((u16)0x7FFF) /* USART OVER8 mode Disable Mask */
+
+/* USART One Bit Sampling Mask */
+#define CR3_ONEBITE_Set ((u16)0x0800) /* USART ONEBITE mode Enable Mask */
+#define CR3_ONEBITE_Reset ((u16)0xF7FF) /* USART ONEBITE mode Disable Mask */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Variables
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_FunctionPrototypes
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Functions
+ * @{
+ */
+
+/**
+ * @brief Deinitializes the USARTx peripheral registers to their default reset values.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @retval None
+ */
+void USART_DeInit(USART_TypeDef* USARTx)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+
+ if (USARTx == USART1)
+ {
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, ENABLE);
+ RCC_APB2PeriphResetCmd(RCC_APB2Periph_USART1, DISABLE);
+ }
+ else if (USARTx == USART2)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART2, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART2, DISABLE);
+ }
+ else if (USARTx == USART3)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART3, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_USART3, DISABLE);
+ }
+ else if (USARTx == UART4)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART4, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART4, DISABLE);
+ }
+ else
+ {
+ if (USARTx == UART5)
+ {
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART5, ENABLE);
+ RCC_APB1PeriphResetCmd(RCC_APB1Periph_UART5, DISABLE);
+ }
+ }
+}
+
+/**
+ * @brief Initializes the USARTx peripheral according to the specified
+ * parameters in the USART_InitStruct .
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_InitStruct: pointer to a USART_InitTypeDef structure
+ * that contains the configuration information for the specified USART
+ * peripheral.
+ * @retval None
+ */
+void USART_Init(USART_TypeDef* USARTx, USART_InitTypeDef* USART_InitStruct)
+{
+ uint32_t tmpreg = 0x00, apbclock = 0x00;
+ uint32_t integerdivider = 0x00;
+ uint32_t fractionaldivider = 0x00;
+ uint32_t usartxbase = 0;
+ RCC_ClocksTypeDef RCC_ClocksStatus;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_BAUDRATE(USART_InitStruct->USART_BaudRate));
+ assert_param(IS_USART_WORD_LENGTH(USART_InitStruct->USART_WordLength));
+ assert_param(IS_USART_STOPBITS(USART_InitStruct->USART_StopBits));
+ assert_param(IS_USART_PARITY(USART_InitStruct->USART_Parity));
+ assert_param(IS_USART_MODE(USART_InitStruct->USART_Mode));
+ assert_param(IS_USART_HARDWARE_FLOW_CONTROL(USART_InitStruct->USART_HardwareFlowControl));
+ /* The hardware flow control is available only for USART1, USART2 and USART3 */
+ if (USART_InitStruct->USART_HardwareFlowControl != USART_HardwareFlowControl_None)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ usartxbase = (uint32_t)USARTx;
+
+/*---------------------------- USART CR2 Configuration -----------------------*/
+ tmpreg = USARTx->CR2;
+ /* Clear STOP[13:12] bits */
+ tmpreg &= CR2_STOP_CLEAR_Mask;
+ /* Configure the USART Stop Bits, Clock, CPOL, CPHA and LastBit ------------*/
+ /* Set STOP[13:12] bits according to USART_StopBits value */
+ tmpreg |= (uint32_t)USART_InitStruct->USART_StopBits;
+
+ /* Write to USART CR2 */
+ USARTx->CR2 = (uint16_t)tmpreg;
+
+/*---------------------------- USART CR1 Configuration -----------------------*/
+ tmpreg = USARTx->CR1;
+ /* Clear M, PCE, PS, TE and RE bits */
+ tmpreg &= CR1_CLEAR_Mask;
+ /* Configure the USART Word Length, Parity and mode ----------------------- */
+ /* Set the M bits according to USART_WordLength value */
+ /* Set PCE and PS bits according to USART_Parity value */
+ /* Set TE and RE bits according to USART_Mode value */
+ tmpreg |= (uint32_t)USART_InitStruct->USART_WordLength | USART_InitStruct->USART_Parity |
+ USART_InitStruct->USART_Mode;
+ /* Write to USART CR1 */
+ USARTx->CR1 = (uint16_t)tmpreg;
+
+/*---------------------------- USART CR3 Configuration -----------------------*/
+ tmpreg = USARTx->CR3;
+ /* Clear CTSE and RTSE bits */
+ tmpreg &= CR3_CLEAR_Mask;
+ /* Configure the USART HFC -------------------------------------------------*/
+ /* Set CTSE and RTSE bits according to USART_HardwareFlowControl value */
+ tmpreg |= USART_InitStruct->USART_HardwareFlowControl;
+ /* Write to USART CR3 */
+ USARTx->CR3 = (uint16_t)tmpreg;
+
+/*---------------------------- USART BRR Configuration -----------------------*/
+ /* Configure the USART Baud Rate -------------------------------------------*/
+ RCC_GetClocksFreq(&RCC_ClocksStatus);
+ if (usartxbase == USART1_BASE)
+ {
+ apbclock = RCC_ClocksStatus.PCLK2_Frequency;
+ }
+ else
+ {
+ apbclock = RCC_ClocksStatus.PCLK1_Frequency;
+ }
+
+ /* Determine the integer part */
+ if ((USARTx->CR1 & CR1_OVER8_Set) != 0)
+ {
+ /* Integer part computing in case Oversampling mode is 8 Samples */
+ integerdivider = ((25 * apbclock) / (2 * (USART_InitStruct->USART_BaudRate)));
+ }
+ else /* if ((USARTx->CR1 & CR1_OVER8_Set) == 0) */
+ {
+ /* Integer part computing in case Oversampling mode is 16 Samples */
+ integerdivider = ((25 * apbclock) / (4 * (USART_InitStruct->USART_BaudRate)));
+ }
+ tmpreg = (integerdivider / 100) << 4;
+
+ /* Determine the fractional part */
+ fractionaldivider = integerdivider - (100 * (tmpreg >> 4));
+
+ /* Implement the fractional part in the register */
+ if ((USARTx->CR1 & CR1_OVER8_Set) != 0)
+ {
+ tmpreg |= ((((fractionaldivider * 8) + 50) / 100)) & ((uint8_t)0x07);
+ }
+ else /* if ((USARTx->CR1 & CR1_OVER8_Set) == 0) */
+ {
+ tmpreg |= ((((fractionaldivider * 16) + 50) / 100)) & ((uint8_t)0x0F);
+ }
+
+ /* Write to USART BRR */
+ USARTx->BRR = (uint16_t)tmpreg;
+}
+
+/**
+ * @brief Fills each USART_InitStruct member with its default value.
+ * @param USART_InitStruct: pointer to a USART_InitTypeDef structure
+ * which will be initialized.
+ * @retval None
+ */
+void USART_StructInit(USART_InitTypeDef* USART_InitStruct)
+{
+ /* USART_InitStruct members default value */
+ USART_InitStruct->USART_BaudRate = 9600;
+ USART_InitStruct->USART_WordLength = USART_WordLength_8b;
+ USART_InitStruct->USART_StopBits = USART_StopBits_1;
+ USART_InitStruct->USART_Parity = USART_Parity_No ;
+ USART_InitStruct->USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
+ USART_InitStruct->USART_HardwareFlowControl = USART_HardwareFlowControl_None;
+}
+
+/**
+ * @brief Initializes the USARTx peripheral Clock according to the
+ * specified parameters in the USART_ClockInitStruct .
+ * @param USARTx: where x can be 1, 2, 3 to select the USART peripheral.
+ * @param USART_ClockInitStruct: pointer to a USART_ClockInitTypeDef
+ * structure that contains the configuration information for the specified
+ * USART peripheral.
+ * @note The Smart Card and Synchronous modes are not available for UART4 and UART5.
+ * @retval None
+ */
+void USART_ClockInit(USART_TypeDef* USARTx, USART_ClockInitTypeDef* USART_ClockInitStruct)
+{
+ uint32_t tmpreg = 0x00;
+ /* Check the parameters */
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ assert_param(IS_USART_CLOCK(USART_ClockInitStruct->USART_Clock));
+ assert_param(IS_USART_CPOL(USART_ClockInitStruct->USART_CPOL));
+ assert_param(IS_USART_CPHA(USART_ClockInitStruct->USART_CPHA));
+ assert_param(IS_USART_LASTBIT(USART_ClockInitStruct->USART_LastBit));
+
+/*---------------------------- USART CR2 Configuration -----------------------*/
+ tmpreg = USARTx->CR2;
+ /* Clear CLKEN, CPOL, CPHA and LBCL bits */
+ tmpreg &= CR2_CLOCK_CLEAR_Mask;
+ /* Configure the USART Clock, CPOL, CPHA and LastBit ------------*/
+ /* Set CLKEN bit according to USART_Clock value */
+ /* Set CPOL bit according to USART_CPOL value */
+ /* Set CPHA bit according to USART_CPHA value */
+ /* Set LBCL bit according to USART_LastBit value */
+ tmpreg |= (uint32_t)USART_ClockInitStruct->USART_Clock | USART_ClockInitStruct->USART_CPOL |
+ USART_ClockInitStruct->USART_CPHA | USART_ClockInitStruct->USART_LastBit;
+ /* Write to USART CR2 */
+ USARTx->CR2 = (uint16_t)tmpreg;
+}
+
+/**
+ * @brief Fills each USART_ClockInitStruct member with its default value.
+ * @param USART_ClockInitStruct: pointer to a USART_ClockInitTypeDef
+ * structure which will be initialized.
+ * @retval None
+ */
+void USART_ClockStructInit(USART_ClockInitTypeDef* USART_ClockInitStruct)
+{
+ /* USART_ClockInitStruct members default value */
+ USART_ClockInitStruct->USART_Clock = USART_Clock_Disable;
+ USART_ClockInitStruct->USART_CPOL = USART_CPOL_Low;
+ USART_ClockInitStruct->USART_CPHA = USART_CPHA_1Edge;
+ USART_ClockInitStruct->USART_LastBit = USART_LastBit_Disable;
+}
+
+/**
+ * @brief Enables or disables the specified USART peripheral.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USARTx peripheral.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_Cmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the selected USART by setting the UE bit in the CR1 register */
+ USARTx->CR1 |= CR1_UE_Set;
+ }
+ else
+ {
+ /* Disable the selected USART by clearing the UE bit in the CR1 register */
+ USARTx->CR1 &= CR1_UE_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the specified USART interrupts.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_IT: specifies the USART interrupt sources to be enabled or disabled.
+ * This parameter can be one of the following values:
+ * @arg USART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg USART_IT_LBD: LIN Break detection interrupt
+ * @arg USART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg USART_IT_TC: Transmission complete interrupt
+ * @arg USART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg USART_IT_IDLE: Idle line detection interrupt
+ * @arg USART_IT_PE: Parity Error interrupt
+ * @arg USART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @param NewState: new state of the specified USARTx interrupts.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_ITConfig(USART_TypeDef* USARTx, uint16_t USART_IT, FunctionalState NewState)
+{
+ uint32_t usartreg = 0x00, itpos = 0x00, itmask = 0x00;
+ uint32_t usartxbase = 0x00;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_CONFIG_IT(USART_IT));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ /* The CTS interrupt is not available for UART4 and UART5 */
+ if (USART_IT == USART_IT_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ usartxbase = (uint32_t)USARTx;
+
+ /* Get the USART register index */
+ usartreg = (((uint8_t)USART_IT) >> 0x05);
+
+ /* Get the interrupt position */
+ itpos = USART_IT & IT_Mask;
+ itmask = (((uint32_t)0x01) << itpos);
+
+ if (usartreg == 0x01) /* The IT is in CR1 register */
+ {
+ usartxbase += 0x0C;
+ }
+ else if (usartreg == 0x02) /* The IT is in CR2 register */
+ {
+ usartxbase += 0x10;
+ }
+ else /* The IT is in CR3 register */
+ {
+ usartxbase += 0x14;
+ }
+ if (NewState != DISABLE)
+ {
+ *(__IO uint32_t*)usartxbase |= itmask;
+ }
+ else
+ {
+ *(__IO uint32_t*)usartxbase &= ~itmask;
+ }
+}
+
+/**
+ * @brief Enables or disables the USART’s DMA interface.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_DMAReq: specifies the DMA request.
+ * This parameter can be any combination of the following values:
+ * @arg USART_DMAReq_Tx: USART DMA transmit request
+ * @arg USART_DMAReq_Rx: USART DMA receive request
+ * @param NewState: new state of the DMA Request sources.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note The DMA mode is not available for UART5 except in the STM32
+ * High density value line devices(STM32F10X_HD_VL).
+ * @retval None
+ */
+void USART_DMACmd(USART_TypeDef* USARTx, uint16_t USART_DMAReq, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_DMAREQ(USART_DMAReq));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the DMA transfer for selected requests by setting the DMAT and/or
+ DMAR bits in the USART CR3 register */
+ USARTx->CR3 |= USART_DMAReq;
+ }
+ else
+ {
+ /* Disable the DMA transfer for selected requests by clearing the DMAT and/or
+ DMAR bits in the USART CR3 register */
+ USARTx->CR3 &= (uint16_t)~USART_DMAReq;
+ }
+}
+
+/**
+ * @brief Sets the address of the USART node.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_Address: Indicates the address of the USART node.
+ * @retval None
+ */
+void USART_SetAddress(USART_TypeDef* USARTx, uint8_t USART_Address)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_ADDRESS(USART_Address));
+
+ /* Clear the USART address */
+ USARTx->CR2 &= CR2_Address_Mask;
+ /* Set the USART address node */
+ USARTx->CR2 |= USART_Address;
+}
+
+/**
+ * @brief Selects the USART WakeUp method.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_WakeUp: specifies the USART wakeup method.
+ * This parameter can be one of the following values:
+ * @arg USART_WakeUp_IdleLine: WakeUp by an idle line detection
+ * @arg USART_WakeUp_AddressMark: WakeUp by an address mark
+ * @retval None
+ */
+void USART_WakeUpConfig(USART_TypeDef* USARTx, uint16_t USART_WakeUp)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_WAKEUP(USART_WakeUp));
+
+ USARTx->CR1 &= CR1_WAKE_Mask;
+ USARTx->CR1 |= USART_WakeUp;
+}
+
+/**
+ * @brief Determines if the USART is in mute mode or not.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART mute mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_ReceiverWakeUpCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the USART mute mode by setting the RWU bit in the CR1 register */
+ USARTx->CR1 |= CR1_RWU_Set;
+ }
+ else
+ {
+ /* Disable the USART mute mode by clearing the RWU bit in the CR1 register */
+ USARTx->CR1 &= CR1_RWU_Reset;
+ }
+}
+
+/**
+ * @brief Sets the USART LIN Break detection length.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_LINBreakDetectLength: specifies the LIN break detection length.
+ * This parameter can be one of the following values:
+ * @arg USART_LINBreakDetectLength_10b: 10-bit break detection
+ * @arg USART_LINBreakDetectLength_11b: 11-bit break detection
+ * @retval None
+ */
+void USART_LINBreakDetectLengthConfig(USART_TypeDef* USARTx, uint16_t USART_LINBreakDetectLength)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_LIN_BREAK_DETECT_LENGTH(USART_LINBreakDetectLength));
+
+ USARTx->CR2 &= CR2_LBDL_Mask;
+ USARTx->CR2 |= USART_LINBreakDetectLength;
+}
+
+/**
+ * @brief Enables or disables the USART’s LIN mode.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART LIN mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_LINCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the LIN mode by setting the LINEN bit in the CR2 register */
+ USARTx->CR2 |= CR2_LINEN_Set;
+ }
+ else
+ {
+ /* Disable the LIN mode by clearing the LINEN bit in the CR2 register */
+ USARTx->CR2 &= CR2_LINEN_Reset;
+ }
+}
+
+/**
+ * @brief Transmits single data through the USARTx peripheral.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param Data: the data to transmit.
+ * @retval None
+ */
+void USART_SendData(USART_TypeDef* USARTx, uint16_t Data)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_DATA(Data));
+
+ /* Transmit Data */
+ USARTx->DR = (Data & (uint16_t)0x01FF);
+}
+
+/**
+ * @brief Returns the most recent received data by the USARTx peripheral.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @retval The received data.
+ */
+uint16_t USART_ReceiveData(USART_TypeDef* USARTx)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+
+ /* Receive Data */
+ return (uint16_t)(USARTx->DR & (uint16_t)0x01FF);
+}
+
+/**
+ * @brief Transmits break characters.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @retval None
+ */
+void USART_SendBreak(USART_TypeDef* USARTx)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+
+ /* Send break characters */
+ USARTx->CR1 |= CR1_SBK_Set;
+}
+
+/**
+ * @brief Sets the specified USART guard time.
+ * @param USARTx: where x can be 1, 2 or 3 to select the USART peripheral.
+ * @param USART_GuardTime: specifies the guard time.
+ * @note The guard time bits are not available for UART4 and UART5.
+ * @retval None
+ */
+void USART_SetGuardTime(USART_TypeDef* USARTx, uint8_t USART_GuardTime)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_123_PERIPH(USARTx));
+
+ /* Clear the USART Guard time */
+ USARTx->GTPR &= GTPR_LSB_Mask;
+ /* Set the USART guard time */
+ USARTx->GTPR |= (uint16_t)((uint16_t)USART_GuardTime << 0x08);
+}
+
+/**
+ * @brief Sets the system clock prescaler.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_Prescaler: specifies the prescaler clock.
+ * @note The function is used for IrDA mode with UART4 and UART5.
+ * @retval None
+ */
+void USART_SetPrescaler(USART_TypeDef* USARTx, uint8_t USART_Prescaler)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+
+ /* Clear the USART prescaler */
+ USARTx->GTPR &= GTPR_MSB_Mask;
+ /* Set the USART prescaler */
+ USARTx->GTPR |= USART_Prescaler;
+}
+
+/**
+ * @brief Enables or disables the USART’s Smart Card mode.
+ * @param USARTx: where x can be 1, 2 or 3 to select the USART peripheral.
+ * @param NewState: new state of the Smart Card mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note The Smart Card mode is not available for UART4 and UART5.
+ * @retval None
+ */
+void USART_SmartCardCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the SC mode by setting the SCEN bit in the CR3 register */
+ USARTx->CR3 |= CR3_SCEN_Set;
+ }
+ else
+ {
+ /* Disable the SC mode by clearing the SCEN bit in the CR3 register */
+ USARTx->CR3 &= CR3_SCEN_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables NACK transmission.
+ * @param USARTx: where x can be 1, 2 or 3 to select the USART peripheral.
+ * @param NewState: new state of the NACK transmission.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note The Smart Card mode is not available for UART4 and UART5.
+ * @retval None
+ */
+void USART_SmartCardNACKCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Enable the NACK transmission by setting the NACK bit in the CR3 register */
+ USARTx->CR3 |= CR3_NACK_Set;
+ }
+ else
+ {
+ /* Disable the NACK transmission by clearing the NACK bit in the CR3 register */
+ USARTx->CR3 &= CR3_NACK_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the USART’s Half Duplex communication.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART Communication.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_HalfDuplexCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the Half-Duplex mode by setting the HDSEL bit in the CR3 register */
+ USARTx->CR3 |= CR3_HDSEL_Set;
+ }
+ else
+ {
+ /* Disable the Half-Duplex mode by clearing the HDSEL bit in the CR3 register */
+ USARTx->CR3 &= CR3_HDSEL_Reset;
+ }
+}
+
+
+/**
+ * @brief Enables or disables the USART's 8x oversampling mode.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART one bit sampling method.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note
+ * This function has to be called before calling USART_Init()
+ * function in order to have correct baudrate Divider value.
+ * @retval None
+ */
+void USART_OverSampling8Cmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the 8x Oversampling mode by setting the OVER8 bit in the CR1 register */
+ USARTx->CR1 |= CR1_OVER8_Set;
+ }
+ else
+ {
+ /* Disable the 8x Oversampling mode by clearing the OVER8 bit in the CR1 register */
+ USARTx->CR1 &= CR1_OVER8_Reset;
+ }
+}
+
+/**
+ * @brief Enables or disables the USART's one bit sampling method.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the USART one bit sampling method.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_OneBitMethodCmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the one bit method by setting the ONEBITE bit in the CR3 register */
+ USARTx->CR3 |= CR3_ONEBITE_Set;
+ }
+ else
+ {
+ /* Disable tthe one bit method by clearing the ONEBITE bit in the CR3 register */
+ USARTx->CR3 &= CR3_ONEBITE_Reset;
+ }
+}
+
+/**
+ * @brief Configures the USART's IrDA interface.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_IrDAMode: specifies the IrDA mode.
+ * This parameter can be one of the following values:
+ * @arg USART_IrDAMode_LowPower
+ * @arg USART_IrDAMode_Normal
+ * @retval None
+ */
+void USART_IrDAConfig(USART_TypeDef* USARTx, uint16_t USART_IrDAMode)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_IRDA_MODE(USART_IrDAMode));
+
+ USARTx->CR3 &= CR3_IRLP_Mask;
+ USARTx->CR3 |= USART_IrDAMode;
+}
+
+/**
+ * @brief Enables or disables the USART's IrDA interface.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param NewState: new state of the IrDA mode.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void USART_IrDACmd(USART_TypeDef* USARTx, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ /* Enable the IrDA mode by setting the IREN bit in the CR3 register */
+ USARTx->CR3 |= CR3_IREN_Set;
+ }
+ else
+ {
+ /* Disable the IrDA mode by clearing the IREN bit in the CR3 register */
+ USARTx->CR3 &= CR3_IREN_Reset;
+ }
+}
+
+/**
+ * @brief Checks whether the specified USART flag is set or not.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_FLAG: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg USART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5)
+ * @arg USART_FLAG_LBD: LIN Break detection flag
+ * @arg USART_FLAG_TXE: Transmit data register empty flag
+ * @arg USART_FLAG_TC: Transmission Complete flag
+ * @arg USART_FLAG_RXNE: Receive data register not empty flag
+ * @arg USART_FLAG_IDLE: Idle Line detection flag
+ * @arg USART_FLAG_ORE: OverRun Error flag
+ * @arg USART_FLAG_NE: Noise Error flag
+ * @arg USART_FLAG_FE: Framing Error flag
+ * @arg USART_FLAG_PE: Parity Error flag
+ * @retval The new state of USART_FLAG (SET or RESET).
+ */
+FlagStatus USART_GetFlagStatus(USART_TypeDef* USARTx, uint16_t USART_FLAG)
+{
+ FlagStatus bitstatus = RESET;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_FLAG(USART_FLAG));
+ /* The CTS flag is not available for UART4 and UART5 */
+ if (USART_FLAG == USART_FLAG_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ if ((USARTx->SR & USART_FLAG) != (uint16_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the USARTx's pending flags.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_FLAG: specifies the flag to clear.
+ * This parameter can be any combination of the following values:
+ * @arg USART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5).
+ * @arg USART_FLAG_LBD: LIN Break detection flag.
+ * @arg USART_FLAG_TC: Transmission Complete flag.
+ * @arg USART_FLAG_RXNE: Receive data register not empty flag.
+ *
+ * @note
+ * - PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
+ * error) and IDLE (Idle line detected) flags are cleared by software
+ * sequence: a read operation to USART_SR register (USART_GetFlagStatus())
+ * followed by a read operation to USART_DR register (USART_ReceiveData()).
+ * - RXNE flag can be also cleared by a read to the USART_DR register
+ * (USART_ReceiveData()).
+ * - TC flag can be also cleared by software sequence: a read operation to
+ * USART_SR register (USART_GetFlagStatus()) followed by a write operation
+ * to USART_DR register (USART_SendData()).
+ * - TXE flag is cleared only by a write to the USART_DR register
+ * (USART_SendData()).
+ * @retval None
+ */
+void USART_ClearFlag(USART_TypeDef* USARTx, uint16_t USART_FLAG)
+{
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_CLEAR_FLAG(USART_FLAG));
+ /* The CTS flag is not available for UART4 and UART5 */
+ if ((USART_FLAG & USART_FLAG_CTS) == USART_FLAG_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ USARTx->SR = (uint16_t)~USART_FLAG;
+}
+
+/**
+ * @brief Checks whether the specified USART interrupt has occurred or not.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_IT: specifies the USART interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg USART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg USART_IT_LBD: LIN Break detection interrupt
+ * @arg USART_IT_TXE: Tansmit Data Register empty interrupt
+ * @arg USART_IT_TC: Transmission complete interrupt
+ * @arg USART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg USART_IT_IDLE: Idle line detection interrupt
+ * @arg USART_IT_ORE: OverRun Error interrupt
+ * @arg USART_IT_NE: Noise Error interrupt
+ * @arg USART_IT_FE: Framing Error interrupt
+ * @arg USART_IT_PE: Parity Error interrupt
+ * @retval The new state of USART_IT (SET or RESET).
+ */
+ITStatus USART_GetITStatus(USART_TypeDef* USARTx, uint16_t USART_IT)
+{
+ uint32_t bitpos = 0x00, itmask = 0x00, usartreg = 0x00;
+ ITStatus bitstatus = RESET;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_GET_IT(USART_IT));
+ /* The CTS interrupt is not available for UART4 and UART5 */
+ if (USART_IT == USART_IT_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ /* Get the USART register index */
+ usartreg = (((uint8_t)USART_IT) >> 0x05);
+ /* Get the interrupt position */
+ itmask = USART_IT & IT_Mask;
+ itmask = (uint32_t)0x01 << itmask;
+
+ if (usartreg == 0x01) /* The IT is in CR1 register */
+ {
+ itmask &= USARTx->CR1;
+ }
+ else if (usartreg == 0x02) /* The IT is in CR2 register */
+ {
+ itmask &= USARTx->CR2;
+ }
+ else /* The IT is in CR3 register */
+ {
+ itmask &= USARTx->CR3;
+ }
+
+ bitpos = USART_IT >> 0x08;
+ bitpos = (uint32_t)0x01 << bitpos;
+ bitpos &= USARTx->SR;
+ if ((itmask != (uint16_t)RESET)&&(bitpos != (uint16_t)RESET))
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the USARTx's interrupt pending bits.
+ * @param USARTx: Select the USART or the UART peripheral.
+ * This parameter can be one of the following values:
+ * USART1, USART2, USART3, UART4 or UART5.
+ * @param USART_IT: specifies the interrupt pending bit to clear.
+ * This parameter can be one of the following values:
+ * @arg USART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg USART_IT_LBD: LIN Break detection interrupt
+ * @arg USART_IT_TC: Transmission complete interrupt.
+ * @arg USART_IT_RXNE: Receive Data register not empty interrupt.
+ *
+ * @note
+ * - PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
+ * error) and IDLE (Idle line detected) pending bits are cleared by
+ * software sequence: a read operation to USART_SR register
+ * (USART_GetITStatus()) followed by a read operation to USART_DR register
+ * (USART_ReceiveData()).
+ * - RXNE pending bit can be also cleared by a read to the USART_DR register
+ * (USART_ReceiveData()).
+ * - TC pending bit can be also cleared by software sequence: a read
+ * operation to USART_SR register (USART_GetITStatus()) followed by a write
+ * operation to USART_DR register (USART_SendData()).
+ * - TXE pending bit is cleared only by a write to the USART_DR register
+ * (USART_SendData()).
+ * @retval None
+ */
+void USART_ClearITPendingBit(USART_TypeDef* USARTx, uint16_t USART_IT)
+{
+ uint16_t bitpos = 0x00, itmask = 0x00;
+ /* Check the parameters */
+ assert_param(IS_USART_ALL_PERIPH(USARTx));
+ assert_param(IS_USART_CLEAR_IT(USART_IT));
+ /* The CTS interrupt is not available for UART4 and UART5 */
+ if (USART_IT == USART_IT_CTS)
+ {
+ assert_param(IS_USART_123_PERIPH(USARTx));
+ }
+
+ bitpos = USART_IT >> 0x08;
+ itmask = ((uint16_t)0x01 << (uint16_t)bitpos);
+ USARTx->SR = (uint16_t)~itmask;
+}
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_wwdg.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_wwdg.c
new file mode 100644
index 00000000..77a7ce51
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/lib/stdperiphlib/STM32F10x_StdPeriph_Driver/src/stm32f10x_wwdg.c
@@ -0,0 +1,224 @@
+/**
+ ******************************************************************************
+ * @file stm32f10x_wwdg.c
+ * @author MCD Application Team
+ * @version V3.5.0
+ * @date 11-March-2011
+ * @brief This file provides all the WWDG firmware functions.
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_CONF_H
+#define __STM32F10x_CONF_H
+
+/* Includes ------------------------------------------------------------------*/
+/* Uncomment/Comment the line below to enable/disable peripheral header file inclusion */
+#include "stm32f10x_adc.h"
+#include "stm32f10x_bkp.h"
+#include "stm32f10x_can.h"
+#include "stm32f10x_cec.h"
+#include "stm32f10x_crc.h"
+#include "stm32f10x_dac.h"
+#include "stm32f10x_dbgmcu.h"
+#include "stm32f10x_dma.h"
+#include "stm32f10x_exti.h"
+#include "stm32f10x_flash.h"
+#include "stm32f10x_fsmc.h"
+#include "stm32f10x_gpio.h"
+#include "stm32f10x_i2c.h"
+#include "stm32f10x_iwdg.h"
+#include "stm32f10x_pwr.h"
+#include "stm32f10x_rcc.h"
+#include "stm32f10x_rtc.h"
+#include "stm32f10x_sdio.h"
+#include "stm32f10x_spi.h"
+#include "stm32f10x_tim.h"
+#include "stm32f10x_usart.h"
+#include "stm32f10x_wwdg.h"
+#include "misc.h" /* High level functions for NVIC and SysTick (add-on to CMSIS functions) */
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/* Uncomment the line below to expanse the "assert_param" macro in the
+ Standard Peripheral Library drivers code */
+/* #define USE_FULL_ASSERT 1 */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function which reports
+ * the name of the source file and the source line number of the call
+ * that failed. If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0)
+#endif /* USE_FULL_ASSERT */
+
+#endif /* __STM32F10x_CONF_H */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/main.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/main.c
new file mode 100644
index 00000000..2992b51f
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/main.c
@@ -0,0 +1,152 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Prog\main.c
+* \brief Demo program application source file.
+* \ingroup Prog_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+
+/****************************************************************************************
+* Include files
+****************************************************************************************/
+#include "header.h" /* generic header */
+
+
+/****************************************************************************************
+* Function prototypes
+****************************************************************************************/
+static void Init(void);
+
+
+/************************************************************************************//**
+** \brief This is the entry point for the bootloader application and is called
+** by the reset interrupt vector after the C-startup routines executed.
+** \return Program return code.
+**
+****************************************************************************************/
+int main(void)
+{
+ /* initialize the microcontroller */
+ Init();
+ /* initialize the bootloader interface */
+ BootComInit();
+
+ /* start the infinite program loop */
+ while (1)
+ {
+ /* toggle LED with a fixed frequency */
+ LedToggle();
+ /* check for bootloader activation request */
+ BootComCheckActivationRequest();
+ }
+
+ /* program should never get here */
+ return 0;
+} /*** end of main ***/
+
+
+/************************************************************************************//**
+** \brief Initializes the microcontroller.
+** \return none.
+**
+****************************************************************************************/
+static void Init(void)
+{
+ volatile unsigned long StartUpCounter = 0, HSEStatus = 0;
+ unsigned long pll_multiplier;
+
+ /* reset the RCC clock configuration to the default reset state (for debug purpose) */
+ /* set HSION bit */
+ RCC->CR |= (unsigned long)0x00000001;
+ /* reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */
+ RCC->CFGR &= (unsigned long)0xF8FF0000;
+ /* reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (unsigned long)0xFEF6FFFF;
+ /* reset HSEBYP bit */
+ RCC->CR &= (unsigned long)0xFFFBFFFF;
+ /* reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */
+ RCC->CFGR &= (unsigned long)0xFF80FFFF;
+ /* disable all interrupts and clear pending bits */
+ RCC->CIR = 0x009F0000;
+ /* enable HSE */
+ RCC->CR |= ((unsigned long)RCC_CR_HSEON);
+ /* wait till HSE is ready and if Time out is reached exit */
+ do
+ {
+ HSEStatus = RCC->CR & RCC_CR_HSERDY;
+ StartUpCounter++;
+ }
+ while((HSEStatus == 0) && (StartUpCounter != 1500));
+ /* check if time out was reached */
+ if ((RCC->CR & RCC_CR_HSERDY) == RESET)
+ {
+ /* cannot continue when HSE is not ready */
+ while (1) { ; }
+ }
+ /* enable flash prefetch buffer */
+ FLASH->ACR |= FLASH_ACR_PRFTBE;
+ /* reset flash wait state configuration to default 0 wait states */
+ FLASH->ACR &= (unsigned long)((unsigned long)~FLASH_ACR_LATENCY);
+#if (BOOT_CPU_SYSTEM_SPEED_KHZ > 48000)
+ /* configure 2 flash wait states */
+ FLASH->ACR |= (unsigned long)FLASH_ACR_LATENCY_2;
+#elif (BOOT_CPU_SYSTEM_SPEED_KHZ > 24000)
+ /* configure 1 flash wait states */
+ FLASH->ACR |= (unsigned long)FLASH_ACR_LATENCY_1;
+#endif
+ /* HCLK = SYSCLK */
+ RCC->CFGR |= (unsigned long)RCC_CFGR_HPRE_DIV1;
+ /* PCLK2 = HCLK/2 */
+ RCC->CFGR |= (unsigned long)RCC_CFGR_PPRE2_DIV2;
+ /* PCLK1 = HCLK/2 */
+ RCC->CFGR |= (unsigned long)RCC_CFGR_PPRE1_DIV2;
+ /* reset PLL configuration */
+ RCC->CFGR &= (unsigned long)((unsigned long)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | \
+ RCC_CFGR_PLLMULL));
+ /* calculate multiplier value */
+ pll_multiplier = BOOT_CPU_SYSTEM_SPEED_KHZ/BOOT_CPU_XTAL_SPEED_KHZ;
+ /* convert to register value */
+ pll_multiplier = (unsigned long)((pll_multiplier - 2) << 18);
+ /* set the PLL multiplier and clock source */
+ RCC->CFGR |= (unsigned long)(RCC_CFGR_PLLSRC_HSE | pll_multiplier);
+ /* enable PLL */
+ RCC->CR |= RCC_CR_PLLON;
+ /* wait till PLL is ready */
+ while((RCC->CR & RCC_CR_PLLRDY) == 0)
+ {
+ }
+ /* select PLL as system clock source */
+ RCC->CFGR &= (unsigned long)((unsigned long)~(RCC_CFGR_SW));
+ RCC->CFGR |= (unsigned long)RCC_CFGR_SW_PLL;
+ /* wait till PLL is used as system clock source */
+ while ((RCC->CFGR & (unsigned long)RCC_CFGR_SWS) != (unsigned long)0x08)
+ {
+ }
+ /* init the led driver */
+ LedInit();
+ /* init the timer driver */
+ TimerInit();
+} /*** end of Init ***/
+
+
+/*********************************** end of main.c *************************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/prog.dox b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/prog.dox
new file mode 100644
index 00000000..059a4125
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/prog.dox
@@ -0,0 +1,14 @@
+/**
+\defgroup Prog_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio User Program
+\ingroup ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+\brief User Program.
+\details The intention of the demo user program is two-fold. (1) To test the
+ bootloader, you need some sort of firmware to see if you can perform a
+ firmware update with the bootloader. This program can be used for this
+ purpose. (2) To make firmware programmable by the bootloader, a few
+ adjustments to the firmware are required. The demo user program serves as an
+ example for how these adjustments can be implemented. Additional details on
+ this subject can be found in the port specifics documentation, which is
+ available at:
+ https://www.feaser.com/openblt/doku.php?id=manual:ports:armcm3_stm32.
+*/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/startup_stm32f10x_md.s b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/startup_stm32f10x_md.s
new file mode 100644
index 00000000..0396376e
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/startup_stm32f10x_md.s
@@ -0,0 +1,370 @@
+/**
+ ******************************************************************************
+ * @file startup_stm32f10x_md.s
+ * @author MCD Application Team
+ * @version V3.6.1
+ * @date 09-March-2012
+ * @brief STM32F10x Medium Density Devices vector table for Atollic toolchain.
+ * This module performs:
+ * - Set the initial SP
+ * - Set the initial PC == Reset_Handler,
+ * - Set the vector table entries with the exceptions ISR address
+ * - Configure the clock system
+ * - Branches to main in the C library (which eventually
+ * calls main()).
+ * After Reset the Cortex-M3 processor is in Thread mode,
+ * priority is Privileged, and the Stack is set to Main.
+ ******************************************************************************
+ * @attention
+ *
+ *
+ *
+ * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
+ * You may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at:
+ *
+ * http://www.st.com/software_license_agreement_liberty_v2
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ *
+ ******************************************************************************
+ */
+
+ .syntax unified
+ .cpu cortex-m3
+ .fpu softvfp
+ .thumb
+
+.global g_pfnVectors
+.global Default_Handler
+
+/* start address for the initialization values of the .data section.
+defined in linker script */
+.word _sidata
+/* start address for the .data section. defined in linker script */
+.word _sdata
+/* end address for the .data section. defined in linker script */
+.word _edata
+/* start address for the .bss section. defined in linker script */
+.word _sbss
+/* end address for the .bss section. defined in linker script */
+.word _ebss
+
+.equ BootRAM, 0xF108F85F
+/**
+ * @brief This is the code that gets called when the processor first
+ * starts execution following a reset event. Only the absolutely
+ * necessary set is performed, after which the application
+ * supplied main() routine is called.
+ * @param None
+ * @retval : None
+*/
+
+ .section .text.Reset_Handler
+ .weak Reset_Handler
+ .type Reset_Handler, %function
+Reset_Handler:
+ ldr sp, =_estack /* Atollic update: set stack pointer */
+
+/* Copy the data segment initializers from flash to SRAM */
+ movs r1, #0
+ b LoopCopyDataInit
+
+CopyDataInit:
+ ldr r3, =_sidata
+ ldr r3, [r3, r1]
+ str r3, [r0, r1]
+ adds r1, r1, #4
+
+LoopCopyDataInit:
+ ldr r0, =_sdata
+ ldr r3, =_edata
+ adds r2, r0, r1
+ cmp r2, r3
+ bcc CopyDataInit
+ ldr r2, =_sbss
+ b LoopFillZerobss
+/* Zero fill the bss segment. */
+FillZerobss:
+ movs r3, #0
+ str r3, [r2], #4
+
+LoopFillZerobss:
+ ldr r3, = _ebss
+ cmp r2, r3
+ bcc FillZerobss
+
+/* Call the clock system intitialization function.*/
+ bl SystemInit
+/* Call static constructors */
+ bl __libc_init_array
+/* Call the application's entry point.*/
+ bl main
+ bx lr
+.size Reset_Handler, .-Reset_Handler
+
+/**
+ * @brief This is the code that gets called when the processor receives an
+ * unexpected interrupt. This simply enters an infinite loop, preserving
+ * the system state for examination by a debugger.
+ *
+ * @param None
+ * @retval : None
+*/
+ .section .text.Default_Handler,"ax",%progbits
+Default_Handler:
+Infinite_Loop:
+ b Infinite_Loop
+ .size Default_Handler, .-Default_Handler
+/******************************************************************************
+*
+* The minimal vector table for a Cortex M3. Note that the proper constructs
+* must be placed on this to ensure that it ends up at physical address
+* 0x0000.0000.
+*
+******************************************************************************/
+ .section .isr_vector,"a",%progbits
+ .type g_pfnVectors, %object
+ .size g_pfnVectors, .-g_pfnVectors
+
+
+g_pfnVectors:
+ .word _estack
+ .word Reset_Handler
+ .word NMI_Handler
+ .word HardFault_Handler
+ .word MemManage_Handler
+ .word BusFault_Handler
+ .word UsageFault_Handler
+ .word 0
+ .word 0
+ .word 0
+ .word 0
+ .word SVC_Handler
+ .word DebugMon_Handler
+ .word 0
+ .word PendSV_Handler
+ .word SysTick_Handler
+ .word WWDG_IRQHandler
+ .word PVD_IRQHandler
+ .word TAMPER_IRQHandler
+ .word RTC_IRQHandler
+ .word FLASH_IRQHandler
+ .word RCC_IRQHandler
+ .word EXTI0_IRQHandler
+ .word EXTI1_IRQHandler
+ .word EXTI2_IRQHandler
+ .word EXTI3_IRQHandler
+ .word EXTI4_IRQHandler
+ .word DMA1_Channel1_IRQHandler
+ .word DMA1_Channel2_IRQHandler
+ .word DMA1_Channel3_IRQHandler
+ .word DMA1_Channel4_IRQHandler
+ .word DMA1_Channel5_IRQHandler
+ .word DMA1_Channel6_IRQHandler
+ .word DMA1_Channel7_IRQHandler
+ .word ADC1_2_IRQHandler
+ .word USB_HP_CAN1_TX_IRQHandler
+ .word USB_LP_CAN1_RX0_IRQHandler
+ .word CAN1_RX1_IRQHandler
+ .word CAN1_SCE_IRQHandler
+ .word EXTI9_5_IRQHandler
+ .word TIM1_BRK_IRQHandler
+ .word TIM1_UP_IRQHandler
+ .word TIM1_TRG_COM_IRQHandler
+ .word TIM1_CC_IRQHandler
+ .word TIM2_IRQHandler
+ .word TIM3_IRQHandler
+ .word TIM4_IRQHandler
+ .word I2C1_EV_IRQHandler
+ .word I2C1_ER_IRQHandler
+ .word I2C2_EV_IRQHandler
+ .word I2C2_ER_IRQHandler
+ .word SPI1_IRQHandler
+ .word SPI2_IRQHandler
+ .word USART1_IRQHandler
+ .word USART2_IRQHandler
+ .word USART3_IRQHandler
+ .word EXTI15_10_IRQHandler
+ .word RTCAlarm_IRQHandler
+ .word USBWakeUp_IRQHandler
+ .word 0
+ .word 0
+ .word 0
+ .word 0
+ .word 0
+ .word 0
+ .word 0
+ .word BootRAM /* @0x108. This is for boot in RAM mode for STM32F10x Medium Density devices. */
+ .word 0x55AA11EE /* Reserved for OpenBLT checksum. */
+
+/*******************************************************************************
+*
+* Provide weak aliases for each Exception handler to the Default_Handler.
+* As they are weak aliases, any function with the same name will override
+* this definition.
+*
+*******************************************************************************/
+
+ .weak NMI_Handler
+ .thumb_set NMI_Handler,Default_Handler
+
+ .weak HardFault_Handler
+ .thumb_set HardFault_Handler,Default_Handler
+
+ .weak MemManage_Handler
+ .thumb_set MemManage_Handler,Default_Handler
+
+ .weak BusFault_Handler
+ .thumb_set BusFault_Handler,Default_Handler
+
+ .weak UsageFault_Handler
+ .thumb_set UsageFault_Handler,Default_Handler
+
+ .weak SVC_Handler
+ .thumb_set SVC_Handler,Default_Handler
+
+ .weak DebugMon_Handler
+ .thumb_set DebugMon_Handler,Default_Handler
+
+ .weak PendSV_Handler
+ .thumb_set PendSV_Handler,Default_Handler
+
+ .weak SysTick_Handler
+ .thumb_set SysTick_Handler,Default_Handler
+
+ .weak WWDG_IRQHandler
+ .thumb_set WWDG_IRQHandler,Default_Handler
+
+ .weak PVD_IRQHandler
+ .thumb_set PVD_IRQHandler,Default_Handler
+
+ .weak TAMPER_IRQHandler
+ .thumb_set TAMPER_IRQHandler,Default_Handler
+
+ .weak RTC_IRQHandler
+ .thumb_set RTC_IRQHandler,Default_Handler
+
+ .weak FLASH_IRQHandler
+ .thumb_set FLASH_IRQHandler,Default_Handler
+
+ .weak RCC_IRQHandler
+ .thumb_set RCC_IRQHandler,Default_Handler
+
+ .weak EXTI0_IRQHandler
+ .thumb_set EXTI0_IRQHandler,Default_Handler
+
+ .weak EXTI1_IRQHandler
+ .thumb_set EXTI1_IRQHandler,Default_Handler
+
+ .weak EXTI2_IRQHandler
+ .thumb_set EXTI2_IRQHandler,Default_Handler
+
+ .weak EXTI3_IRQHandler
+ .thumb_set EXTI3_IRQHandler,Default_Handler
+
+ .weak EXTI4_IRQHandler
+ .thumb_set EXTI4_IRQHandler,Default_Handler
+
+ .weak DMA1_Channel1_IRQHandler
+ .thumb_set DMA1_Channel1_IRQHandler,Default_Handler
+
+ .weak DMA1_Channel2_IRQHandler
+ .thumb_set DMA1_Channel2_IRQHandler,Default_Handler
+
+ .weak DMA1_Channel3_IRQHandler
+ .thumb_set DMA1_Channel3_IRQHandler,Default_Handler
+
+ .weak DMA1_Channel4_IRQHandler
+ .thumb_set DMA1_Channel4_IRQHandler,Default_Handler
+
+ .weak DMA1_Channel5_IRQHandler
+ .thumb_set DMA1_Channel5_IRQHandler,Default_Handler
+
+ .weak DMA1_Channel6_IRQHandler
+ .thumb_set DMA1_Channel6_IRQHandler,Default_Handler
+
+ .weak DMA1_Channel7_IRQHandler
+ .thumb_set DMA1_Channel7_IRQHandler,Default_Handler
+
+ .weak ADC1_2_IRQHandler
+ .thumb_set ADC1_2_IRQHandler,Default_Handler
+
+ .weak USB_HP_CAN1_TX_IRQHandler
+ .thumb_set USB_HP_CAN1_TX_IRQHandler,Default_Handler
+
+ .weak USB_LP_CAN1_RX0_IRQHandler
+ .thumb_set USB_LP_CAN1_RX0_IRQHandler,Default_Handler
+
+ .weak CAN1_RX1_IRQHandler
+ .thumb_set CAN1_RX1_IRQHandler,Default_Handler
+
+ .weak CAN1_SCE_IRQHandler
+ .thumb_set CAN1_SCE_IRQHandler,Default_Handler
+
+ .weak EXTI9_5_IRQHandler
+ .thumb_set EXTI9_5_IRQHandler,Default_Handler
+
+ .weak TIM1_BRK_IRQHandler
+ .thumb_set TIM1_BRK_IRQHandler,Default_Handler
+
+ .weak TIM1_UP_IRQHandler
+ .thumb_set TIM1_UP_IRQHandler,Default_Handler
+
+ .weak TIM1_TRG_COM_IRQHandler
+ .thumb_set TIM1_TRG_COM_IRQHandler,Default_Handler
+
+ .weak TIM1_CC_IRQHandler
+ .thumb_set TIM1_CC_IRQHandler,Default_Handler
+
+ .weak TIM2_IRQHandler
+ .thumb_set TIM2_IRQHandler,Default_Handler
+
+ .weak TIM3_IRQHandler
+ .thumb_set TIM3_IRQHandler,Default_Handler
+
+ .weak TIM4_IRQHandler
+ .thumb_set TIM4_IRQHandler,Default_Handler
+
+ .weak I2C1_EV_IRQHandler
+ .thumb_set I2C1_EV_IRQHandler,Default_Handler
+
+ .weak I2C1_ER_IRQHandler
+ .thumb_set I2C1_ER_IRQHandler,Default_Handler
+
+ .weak I2C2_EV_IRQHandler
+ .thumb_set I2C2_EV_IRQHandler,Default_Handler
+
+ .weak I2C2_ER_IRQHandler
+ .thumb_set I2C2_ER_IRQHandler,Default_Handler
+
+ .weak SPI1_IRQHandler
+ .thumb_set SPI1_IRQHandler,Default_Handler
+
+ .weak SPI2_IRQHandler
+ .thumb_set SPI2_IRQHandler,Default_Handler
+
+ .weak USART1_IRQHandler
+ .thumb_set USART1_IRQHandler,Default_Handler
+
+ .weak USART2_IRQHandler
+ .thumb_set USART2_IRQHandler,Default_Handler
+
+ .weak USART3_IRQHandler
+ .thumb_set USART3_IRQHandler,Default_Handler
+
+ .weak EXTI15_10_IRQHandler
+ .thumb_set EXTI15_10_IRQHandler,Default_Handler
+
+ .weak RTCAlarm_IRQHandler
+ .thumb_set RTCAlarm_IRQHandler,Default_Handler
+
+ .weak USBWakeUp_IRQHandler
+ .thumb_set USBWakeUp_IRQHandler,Default_Handler
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/stm32_flash.ld b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/stm32_flash.ld
new file mode 100644
index 00000000..c53d6ed5
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/stm32_flash.ld
@@ -0,0 +1,178 @@
+/*
+******************************************************************************
+File: stm32_flash.ld
+Info: Generated by Atollic TrueSTUDIO(R) 9.0.1 2018-06-07
+
+Abstract: Linker script for STM32F103RB device
+ Set heap size, stack size, stack location, memory areas and
+ sections according to application requirements.
+
+The MIT License (MIT)
+Copyright (c) 2018 STMicroelectronics
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.
+
+******************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20005000; /* end of 20K RAM */
+
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x800; /* required amount of heap */
+_Min_Stack_Size = 0x800; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+ FLASH (rx) : ORIGIN = 0x08002000, LENGTH = 128K-8K
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 20K
+ MEMORY_B1 (rx) : ORIGIN = 0x60000000, LENGTH = 0K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(4);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(4);
+ } >RAM
+
+ /* MEMORY_bank1 section, code must be located here explicitly */
+ /* Example: extern int foo(void) __attribute__ ((section (".mb1text"))); */
+ .memory_b1_text :
+ {
+ *(.mb1text) /* .mb1text sections (code) */
+ *(.mb1text*) /* .mb1text* sections (code) */
+ *(.mb1rodata) /* read-only data (constants) */
+ *(.mb1rodata*)
+ } >MEMORY_B1
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/timer.c b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/timer.c
new file mode 100644
index 00000000..c1dda01e
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/timer.c
@@ -0,0 +1,106 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Prog\timer.c
+* \brief Timer driver source file.
+* \ingroup Prog_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+
+/****************************************************************************************
+* Include files
+****************************************************************************************/
+#include "header.h" /* generic header */
+
+
+/****************************************************************************************
+* Local data declarations
+****************************************************************************************/
+/** \brief Local variable for storing the number of milliseconds that have elapsed since
+ * startup.
+ */
+static unsigned long millisecond_counter;
+
+
+/************************************************************************************//**
+** \brief Initializes the timer.
+** \return none.
+**
+****************************************************************************************/
+void TimerInit(void)
+{
+ /* configure the SysTick timer for 1 ms period */
+ SysTick_Config(BOOT_CPU_SYSTEM_SPEED_KHZ);
+ /* reset the millisecond counter */
+ TimerSet(0);
+} /*** end of TimerInit ***/
+
+
+/************************************************************************************//**
+** \brief Stops the timer.
+** \return none.
+**
+****************************************************************************************/
+void TimerDeinit(void)
+{
+ SysTick->CTRL = 0;
+} /*** end of TimerDeinit ***/
+
+
+/************************************************************************************//**
+** \brief Sets the initial counter value of the millisecond timer.
+** \param timer_value initialize value of the millisecond timer.
+** \return none.
+**
+****************************************************************************************/
+void TimerSet(unsigned long timer_value)
+{
+ /* set the millisecond counter */
+ millisecond_counter = timer_value;
+} /*** end of TimerSet ***/
+
+
+/************************************************************************************//**
+** \brief Obtains the counter value of the millisecond timer.
+** \return Current value of the millisecond timer.
+**
+****************************************************************************************/
+unsigned long TimerGet(void)
+{
+ /* read and return the millisecond counter value */
+ return millisecond_counter;
+} /*** end of TimerGet ***/
+
+
+/************************************************************************************//**
+** \brief Interrupt service routine of the timer.
+** \return none.
+**
+****************************************************************************************/
+void SysTick_Handler(void)
+{
+ /* increment the millisecond counter */
+ millisecond_counter++;
+} /*** end of SysTick_Handler ***/
+
+
+/*********************************** end of timer.c ************************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/timer.h b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/timer.h
new file mode 100644
index 00000000..2da1ff5e
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/Prog/timer.h
@@ -0,0 +1,40 @@
+/************************************************************************************//**
+* \file Demo\ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio\Prog\timer.h
+* \brief Timer driver header file.
+* \ingroup Prog_ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio
+* \internal
+*----------------------------------------------------------------------------------------
+* C O P Y R I G H T
+*----------------------------------------------------------------------------------------
+* Copyright (c) 2018 by Feaser http://www.feaser.com All rights reserved
+*
+*----------------------------------------------------------------------------------------
+* L I C E N S E
+*----------------------------------------------------------------------------------------
+* This file is part of OpenBLT. OpenBLT is free software: you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as published by the Free
+* Software Foundation, either version 3 of the License, or (at your option) any later
+* version.
+*
+* OpenBLT is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+* without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+* PURPOSE. See the GNU General Public License for more details.
+*
+* You have received a copy of the GNU General Public License along with OpenBLT. It
+* should be located in ".\Doc\license.html". If not, contact Feaser to obtain a copy.
+*
+* \endinternal
+****************************************************************************************/
+#ifndef TIMER_H
+#define TIMER_H
+
+/****************************************************************************************
+* Function prototypes
+****************************************************************************************/
+void TimerInit(void);
+void TimerDeinit(void);
+void TimerSet(unsigned long timer_value);
+unsigned long TimerGet(void);
+
+#endif /* TIMER_H */
+/*********************************** end of timer.h ************************************/
diff --git a/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/demo.dox b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/demo.dox
new file mode 100644
index 00000000..0f6af3db
--- /dev/null
+++ b/Target/Demo/ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio/demo.dox
@@ -0,0 +1,9 @@
+/**
+\defgroup ARMCM3_STM32F1_Nucleo_F103RB_TrueStudio Demo for Nucleo-F103RB/TrueStudio
+\ingroup Demos
+\brief Preconfigured programs for the Nucleo-F103RB and the Atollic TrueStudio toolchain.
+\details For detailed getting started instructions, refer to:
+ https://www.feaser.com/openblt/doku.php?id=manual:demos:nucleo_f103rb_truestudio.
+*/
+
+