/***************************************************************************//**
 * @file
 * @brief Universal synchronous/asynchronous receiver/transmitter (USART/UART)
 *   peripheral module peripheral API for EFM32.
 * @author Energy Micro AS
 * @version 2.3.2
 *******************************************************************************
 * @section License
 * <b>(C) Copyright 2010 Energy Micro AS, http://www.energymicro.com</b>
 *******************************************************************************
 *
 * This source code is the property of Energy Micro AS. The source and compiled
 * code may only be used on Energy Micro "EFM32" microcontrollers.
 *
 * This copyright notice may not be removed from the source code nor changed.
 *
 * DISCLAIMER OF WARRANTY/LIMITATION OF REMEDIES: Energy Micro AS has no
 * obligation to support this Software. Energy Micro AS is providing the
 * Software "AS IS", with no express or implied warranties of any kind,
 * including, but not limited to, any implied warranties of merchantability
 * or fitness for any particular purpose or warranties against infringement
 * of any proprietary rights of a third party.
 *
 * Energy Micro AS will not be liable for any consequential, incidental, or
 * special damages, or any other relief, or for any claim by any third party,
 * arising from your use of this Software.
 *
 ******************************************************************************/
#include "efm32_usart.h"
#include "efm32_cmu.h"
#include "efm32_assert.h"

/***************************************************************************//**
 * @addtogroup EFM32_Library
 * @{
 ******************************************************************************/

/***************************************************************************//**
 * @addtogroup USART
 * @brief Universal Synchronous/Asynchronous Receiver/Transmitter
 *   Peripheral API for EFM32
 * @{
 ******************************************************************************/

/*******************************************************************************
 *******************************   DEFINES   ***********************************
 ******************************************************************************/

/** @cond DO_NOT_INCLUDE_WITH_DOXYGEN */


/** Validation of USART register block pointer reference for assert statements. */
#if (USART_COUNT == 1)
#define USART_REF_VALID(ref)    ((ref) == USART0)

#elif (USART_COUNT == 2)
#define USART_REF_VALID(ref)    (((ref) == USART0) || ((ref) == USART1))

#elif (USART_COUNT == 3)
#define USART_REF_VALID(ref)    (((ref) == USART0) || ((ref) == USART1) || \
                                 ((ref) == USART2))
#elif (USART_COUNT == 4)
#define USART_REF_VALID(ref)    (((ref) == USART0) || ((ref) == USART1) || \
                                 ((ref) == USART2) || ((ref) == USART3))
#else
#error Undefined number of USARTs.
#endif

#define USART_IRDA_VALID(ref)    ((ref) == USART0)

#if defined(_EFM32_TINY_FAMILY)
#define USART_I2S_VALID(ref)     ((ref) == USART1)
#endif

#if defined(_EFM32_GIANT_FAMILY)
#define USART_I2S_VALID(ref)    (((ref) == USART1) || ((ref) == USART2))
#endif

#if (UART_COUNT == 1)
#define UART_REF_VALID(ref)     ((ref)==UART0) 
#elif (UART_COUNT == 2)
#define UART_REF_VALID(ref)     (((ref)==UART0) || ((ref)==UART1))
#else
#define UART_REF_VALID(ref)     (0)
#endif

/** @endcond */


/*******************************************************************************
 **************************   GLOBAL FUNCTIONS   *******************************
 ******************************************************************************/

/***************************************************************************//**
 * @brief
 *   Configure USART/UART operating in asynchronous mode to use a given
 *   baudrate (or as close as possible to specified baudrate).
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @param[in] refFreq
 *   USART/UART reference clock frequency in Hz that will be used. If set to 0,
 *   the currently configured reference clock is assumed.
 *
 * @param[in] baudrate
 *   Baudrate to try to achieve for USART/UART.
 *
 * @param[in] ovs
 *   Oversampling to be used. Normal is 16x oversampling, but lower oversampling
 *   may be used to achieve higher rates or better baudrate accuracy in some
 *   cases. Notice that lower oversampling frequency makes channel more
 *   vulnerable to bit faults during reception due to clock inaccuracies
 *   compared to link partner.
 ******************************************************************************/
void USART_BaudrateAsyncSet(USART_TypeDef *usart,
                            uint32_t refFreq,
                            uint32_t baudrate,
                            USART_OVS_TypeDef ovs)
{
  uint32_t clkdiv;
  uint32_t oversample;

  /* Inhibit divide by 0 */
  EFM_ASSERT(baudrate);

  /*
   * We want to use integer division to avoid forcing in float division
   * utils, and yet keep rounding effect errors to a minimum.
   *
   * CLKDIV in asynchronous mode is given by:
   *
   * CLKDIV = 256 * (fHFPERCLK/(oversample * br) - 1)
   * or
   * CLKDIV = (256 * fHFPERCLK)/(oversample * br) - 256
   *
   * The basic problem with integer division in the above formula is that
   * the dividend (256 * fHFPERCLK) may become higher than max 32 bit
   * integer. Yet, we want to evaluate dividend first before dividing in
   * order to get as small rounding effects as possible. We do not want
   * to make too harsh restrictions on max fHFPERCLK value either.
   *
   * One can possibly factorize 256 and oversample/br. However,
   * since the last 6 bits of CLKDIV are don't care, we can base our
   * integer arithmetic on the below formula
   *
   * CLKDIV / 64 = (4 * fHFPERCLK)/(oversample * br) - 4
   *
   * and calculate 1/64 of CLKDIV first. This allows for fHFPERCLK
   * up to 1GHz without overflowing a 32 bit value!
   */

  /* HFPERCLK used to clock all USART/UART peripheral modules */
  if (!refFreq)
  {
    refFreq = CMU_ClockFreqGet(cmuClock_HFPER);
  }

  /* Map oversampling */
  switch (ovs)
  {
  case USART_CTRL_OVS_X16:
    EFM_ASSERT(baudrate <= (refFreq / 16));
    oversample = 16;
    break;

  case USART_CTRL_OVS_X8:
    EFM_ASSERT(baudrate <= (refFreq / 8));
    oversample = 8;
    break;

  case USART_CTRL_OVS_X6:
    EFM_ASSERT(baudrate <= (refFreq / 6));
    oversample = 6;
    break;

  case USART_CTRL_OVS_X4:
    EFM_ASSERT(baudrate <= (refFreq / 4));
    oversample = 4;
    break;

  default:
    /* Invalid input */
    EFM_ASSERT(0);
    return;
  }

  /* Calculate and set CLKDIV with fractional bits */
  clkdiv  = 4 * refFreq + (oversample * baudrate) / 2;
  clkdiv /= (oversample * baudrate);
  clkdiv -= 4;
  clkdiv *= 64;

  usart->CTRL  &= ~_USART_CTRL_OVS_MASK;
  usart->CTRL  |= ovs;
  usart->CLKDIV = clkdiv;
}


/***************************************************************************//**
 * @brief
 *   Calculate baudrate for USART/UART given reference frequency, clock division
 *   and oversampling rate (if async mode).
 *
 * @details
 *   This function returns the baudrate that a USART/UART module will use if
 *   configured with the given frequency, clock divisor and mode. Notice that
 *   this function will not use actual HW configuration. It can be used
 *   to determinate if a given configuration is sufficiently accurate for the
 *   application.
 *
 * @param[in] refFreq
 *   USART/UART HF peripheral frequency used.
 *
 * @param[in] clkdiv
 *   Clock division factor to be used.
 *
 * @param[in] syncmode
 *   @li true - synchronous mode operation.
 *   @li false - asynchronous mode operation.
 *
 * @param[in] ovs
 *   Oversampling used if asynchronous mode. Not used if @p syncmode is true.
 *
 * @return
 *   Baudrate with given settings.
 ******************************************************************************/
uint32_t USART_BaudrateCalc(uint32_t refFreq,
                            uint32_t clkdiv,
                            bool syncmode,
                            USART_OVS_TypeDef ovs)
{
  uint32_t oversample;
  uint32_t divisor;
  uint32_t factor;
  uint32_t remainder;
  uint32_t quotient;
  uint32_t br;

  /* Mask out unused bits */
  clkdiv &= _USART_CLKDIV_MASK;

  /* We want to use integer division to avoid forcing in float division */
  /* utils, and yet keep rounding effect errors to a minimum. */

  /* Baudrate calculation depends on if synchronous or asynchronous mode */
  if (syncmode)
  {
    /*
     * Baudrate is given by:
     *
     * br = fHFPERCLK/(2 * (1 + (CLKDIV / 256)))
     *
     * which can be rewritten to
     *
     * br = (128 * fHFPERCLK)/(256 + CLKDIV)
     */
    oversample = 1; /* Not used in sync mode, ie 1 */
    factor     = 128;
  }
  else
  {
    /*
     * Baudrate in asynchronous mode is given by:
     *
     * br = fHFPERCLK/(oversample * (1 + (CLKDIV / 256)))
     *
     * which can be rewritten to
     *
     * br = (256 * fHFPERCLK)/(oversample * (256 + CLKDIV))
     *
     * First of all we can reduce the 256 factor of the dividend with
     * (part of) oversample part of the divisor.
     */

    switch (ovs)
    {
    case USART_CTRL_OVS_X16:
      oversample = 1;
      factor     = 256 / 16;
      break;

    case USART_CTRL_OVS_X8:
      oversample = 1;
      factor     = 256 / 8;
      break;

    case USART_CTRL_OVS_X6:
      oversample = 3;
      factor     = 256 / 2;
      break;

    default:
      oversample = 1;
      factor     = 256 / 4;
      break;
    }
  }

  /*
   * The basic problem with integer division in the above formula is that
   * the dividend (factor * fHFPERCLK) may become higher than max 32 bit
   * integer. Yet we want to evaluate dividend first before dividing in
   * order to get as small rounding effects as possible. We do not want
   * to make too harsh restrictions on max fHFPERCLK value either.
   *
   * For division a/b, we can write
   *
   * a = qb + r
   *
   * where q is the quotient and r is the remainder, both integers.
   *
   * The orignal baudrate formula can be rewritten as
   *
   * br = xa / b = x(qb + r)/b = xq + xr/b
   *
   * where x is 'factor', a is 'refFreq' and b is 'divisor', referring to
   * variable names.
   */

  /* Divisor will never exceed max 32 bit value since clkdiv <= 0x1fffc0 */
  /* and 'oversample' has been reduced to <= 3. */
  divisor = oversample * (256 + clkdiv);

  quotient  = refFreq / divisor;
  remainder = refFreq % divisor;

  /* factor <= 128 and since divisor >= 256, the below cannot exceed max */
  /* 32 bit value. */
  br = factor * quotient;

  /*
   * factor <= 128 and remainder < (oversample*(256 + clkdiv)), which
   * means dividend (factor * remainder) worst case is
   * 128*(3 * (256 + 0x1fffc0)) = 0x30012000.
   */
  br += (factor * remainder) / divisor;

  return br;
}


/***************************************************************************//**
 * @brief
 *   Get current baudrate for USART/UART.
 *
 * @details
 *   This function returns the actual baudrate (not considering oscillator
 *   inaccuracies) used by a USART/UART peripheral.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @return
 *   Current baudrate.
 ******************************************************************************/
uint32_t USART_BaudrateGet(USART_TypeDef *usart)
{
  uint32_t          freq;
  USART_OVS_TypeDef ovs;
  bool              syncmode;

  if (usart->CTRL & USART_CTRL_SYNC)
  {
    syncmode = true;
  }
  else
  {
    syncmode = false;
  }

  /* HFPERCLK used to clock all USART/UART peripheral modules */
  freq = CMU_ClockFreqGet(cmuClock_HFPER);
  ovs  = (USART_OVS_TypeDef)(usart->CTRL & _USART_CTRL_OVS_MASK);
  return USART_BaudrateCalc(freq, usart->CLKDIV, syncmode, ovs);
}


/***************************************************************************//**
 * @brief
 *   Configure USART operating in synchronous mode to use a given baudrate
 *   (or as close as possible to specified baudrate).
 *
 * @details
 *   The configuration will be set to use a baudrate <= the specified baudrate
 *   in order to ensure that the baudrate does not exceed the specified value.
 *
 *   Fractional clock division is suppressed, although the HW design allows it.
 *   It could cause half clock cycles to exceed specified limit, and thus
 *   potentially violate specifications for the slave device. In some special
 *   situations fractional clock division may be useful even in synchronous
 *   mode, but in those cases it must be directly adjusted, possibly assisted
 *   by USART_BaudrateCalc():
 *
 * @param[in] usart
 *   Pointer to USART peripheral register block. (Cannot be used on UART
 *   modules.)
 *
 * @param[in] refFreq
 *   USART reference clock frequency in Hz that will be used. If set to 0,
 *   the currently configured reference clock is assumed.
 *
 * @param[in] baudrate
 *   Baudrate to try to achieve for USART.
 ******************************************************************************/
void USART_BaudrateSyncSet(USART_TypeDef *usart, uint32_t refFreq, uint32_t baudrate)
{
  uint32_t clkdiv;

  /* Inhibit divide by 0 */
  EFM_ASSERT(baudrate);

  /*
   * We want to use integer division to avoid forcing in float division
   * utils, and yet keep rounding effect errors to a minimum.
   *
   * CLKDIV in synchronous mode is given by:
   *
   * CLKDIV = 256 * (fHFPERCLK/(2 * br) - 1)
   * or
   * CLKDIV = (256 * fHFPERCLK)/(2 * br) - 256 = (128 * fHFPERCLK)/br - 256
   *
   * The basic problem with integer division in the above formula is that
   * the dividend (128 * fHFPERCLK) may become higher than max 32 bit
   * integer. Yet, we want to evaluate dividend first before dividing in
   * order to get as small rounding effects as possible. We do not want
   * to make too harsh restrictions on max fHFPERCLK value either.
   *
   * One can possibly factorize 128 and br. However, since the last
   * 6 bits of CLKDIV are don't care, we can base our integer arithmetic
   * on the below formula without loosing any extra precision:
   *
   * CLKDIV / 64 = (2 * fHFPERCLK)/br - 4
   *
   * and calculate 1/64 of CLKDIV first. This allows for fHFPERCLK
   * up to 2GHz without overflowing a 32 bit value!
   */

  /* HFPERCLK used to clock all USART/UART peripheral modules */
  if (!refFreq)
  {
    refFreq = CMU_ClockFreqGet(cmuClock_HFPER);
  }

  /* Calculate and set CLKDIV with fractional bits */
  clkdiv  = 2 * refFreq;
  clkdiv /= baudrate;
  clkdiv -= 4;
  clkdiv *= 64;
  /* Make sure we don't use fractional bits by rounding CLKDIV */
  /* up (and thus reducing baudrate, not increasing baudrate above */
  /* specified value). */
  clkdiv       += 0xc0;
  clkdiv       &= 0xffffff00;
  clkdiv       &= _USART_CLKDIV_DIV_MASK;
  usart->CLKDIV = clkdiv;
}


/***************************************************************************//**
 * @brief
 *   Enable/disable USART/UART receiver and/or transmitter.
 *
 * @details
 *   Notice that this function does not do any configuration. Enabling should
 *   normally be done after initialization is done (if not enabled as part
 *   of init).
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @param[in] enable
 *   Select status for receiver/transmitter.
 ******************************************************************************/
void USART_Enable(USART_TypeDef *usart, USART_Enable_TypeDef enable)
{
  uint32_t tmp;

  /* Make sure the module exists on the selected chip */
  EFM_ASSERT(USART_REF_VALID(usart)||(UART_REF_VALID(usart)));

  /* Disable as specified */
  tmp        = ~((uint32_t)(enable));
  tmp       &= _USART_CMD_RXEN_MASK | _USART_CMD_TXEN_MASK;
  usart->CMD = tmp << 1;

  /* Enable as specified */
  usart->CMD = (uint32_t)(enable);
}


/***************************************************************************//**
 * @brief
 *   Init USART/UART for normal asynchronous mode.
 *
 * @details
 *   This function will configure basic settings in order to operate in normal
 *   asynchronous mode.
 *
 *   Special control setup not covered by this function must be done after
 *   using this function by direct modification of the CTRL register.
 *
 *   Notice that pins used by the USART/UART module must be properly configured
 *   by the user explicitly, in order for the USART/UART to work as intended.
 *   (When configuring pins, one should remember to consider the sequence of
 *   configuration, in order to avoid unintended pulses/glitches on output
 *   pins.)
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @param[in] init
 *   Pointer to initialization structure used to configure basic async setup.
 ******************************************************************************/
void USART_InitAsync(USART_TypeDef *usart, const USART_InitAsync_TypeDef *init)
{
  /* Make sure the module exists on the selected chip */
  EFM_ASSERT(USART_REF_VALID(usart)||UART_REF_VALID(usart));

  /* Init USART registers to HW reset state. */
  USART_Reset(usart);

#if defined(_EFM32_GIANT_FAMILY) || defined(_EFM32_TINY_FAMILY)
  /* Disable majority vote if specified. */
  if (init->mvdis)
  {
    usart->CTRL |= USART_CTRL_MVDIS;
  }

  /* Configure PRS input mode. */
  if (init->prsRxEnable)
  {
    usart->INPUT = (uint32_t)init->prsRxCh | USART_INPUT_RXPRS;
  }
#endif

  /* Configure databits, stopbits and parity */
  usart->FRAME = (uint32_t)(init->databits) |
                 (uint32_t)(init->stopbits) |
                 (uint32_t)(init->parity);

  /* Configure baudrate */
  USART_BaudrateAsyncSet(usart, init->refFreq, init->baudrate, init->oversampling);

  /* Finally enable (as specified) */
  usart->CMD = (uint32_t)(init->enable);
}


/***************************************************************************//**
 * @brief
 *   Init USART for synchronous mode.
 *
 * @details
 *   This function will configure basic settings in order to operate in
 *   synchronous mode.
 *
 *   Special control setup not covered by this function must be done after
 *   using this function by direct modification of the CTRL register.
 *
 *   Notice that pins used by the USART module must be properly configured
 *   by the user explicitly, in order for the USART to work as intended.
 *   (When configuring pins, one should remember to consider the sequence of
 *   configuration, in order to avoid unintended pulses/glitches on output
 *   pins.)
 *
 * @param[in] usart
 *   Pointer to USART peripheral register block. (UART does not support this
 *   mode.)
 *
 * @param[in] init
 *   Pointer to initialization structure used to configure basic async setup.
 ******************************************************************************/
void USART_InitSync(USART_TypeDef *usart, const USART_InitSync_TypeDef *init)
{
  /* Make sure the module exists on the selected chip */
  EFM_ASSERT(USART_REF_VALID(usart));

  /* Init USART registers to HW reset state. */
  USART_Reset(usart);

  /* Set bits for synchronous mode */
  usart->CTRL |= (USART_CTRL_SYNC) |
                 ((uint32_t)init->clockMode) |
                 (init->msbf ? USART_CTRL_MSBF : 0);

#if defined(_EFM32_GIANT_FAMILY) || defined(_EFM32_TINY_FAMILY)
  usart->CTRL |= (init->prsRxEnable ? USART_INPUT_RXPRS : 0) |
                 (init->autoTx      ? USART_CTRL_AUTOTX : 0);
#endif

  /* Configure databits, leave stopbits and parity at reset default (not used) */
  usart->FRAME = ((uint32_t)(init->databits)) |
                 (USART_FRAME_STOPBITS_DEFAULT) |
                 (USART_FRAME_PARITY_DEFAULT);

  /* Configure baudrate */
  USART_BaudrateSyncSet(usart, init->refFreq, init->baudrate);

  /* Finally enable (as specified) */
  if (init->master)
  {
    usart->CMD = USART_CMD_MASTEREN;
  }

  usart->CMD = (uint32_t)(init->enable);
}


/***************************************************************************//**
 * @brief
 *   Init USART0 for asynchronous IrDA mode.
 *
 * @details
 *   This function will configure basic settings in order to operate in
 *   asynchronous IrDA mode.
 *
 *   Special control setup not covered by this function must be done after
 *   using this function by direct modification of the CTRL and IRCTRL
 *   registers.
 *
 *   Notice that pins used by the USART/UART module must be properly configured
 *   by the user explicitly, in order for the USART/UART to work as intended.
 *   (When configuring pins, one should remember to consider the sequence of
 *   configuration, in order to avoid unintended pulses/glitches on output
 *   pins.)
 *
 * @param[in] init
 *   Pointer to initialization structure used to configure async IrDA setup.
 *
 * @note
 *   This function only applies to USART0 as IrDA is not supported on the other
 *   USART modules.
 *
 ******************************************************************************/
void USART_InitIrDA(const USART_InitIrDA_TypeDef *init)
{
  /* Init USART0 as async device */
  USART_InitAsync(USART0, &(init->async));

  /* Set IrDA modulation to RZI (return-to-zero-inverted) */
  USART0->CTRL |= USART_CTRL_TXINV;

  /* Invert Rx signal before demodulator if enabled */
  if (init->irRxInv)
  {
    USART0->CTRL |= USART_CTRL_RXINV;
  }

  /* Configure IrDA */
  USART0->IRCTRL |= (uint32_t)init->irPw |
                    (uint32_t)init->irPrsSel |
                    ((uint32_t)init->irFilt << _USART_IRCTRL_IRFILT_SHIFT) |
                    ((uint32_t)init->irPrsEn << _USART_IRCTRL_IRPRSEN_SHIFT);

  /* Enable IrDA */
  USART0->IRCTRL |= USART_IRCTRL_IREN;
}


#if defined(_EFM32_GIANT_FAMILY) || defined(_EFM32_TINY_FAMILY)
/***************************************************************************//**
 * @brief
 *   Init USART for I2S mode.
 *
 * @details
 *   This function will configure basic settings in order to operate in I2S
 *   mode.
 *
 *   Special control setup not covered by this function must be done after
 *   using this function by direct modification of the CTRL and I2SCTRL
 *   registers.
 *
 *   Notice that pins used by the USART module must be properly configured
 *   by the user explicitly, in order for the USART to work as intended.
 *   (When configuring pins, one should remember to consider the sequence of
 *   configuration, in order to avoid unintended pulses/glitches on output
 *   pins.)
 *
 * @param[in] usart
 *   Pointer to USART peripheral register block. (UART does not support this
 *   mode.)
 *
 * @param[in] init
 *   Pointer to initialization structure used to configure basic I2S setup.
 *
 * @note
 *   This function does not apply to all USART's. Refer to chip manuals.
 *
 ******************************************************************************/
void USART_InitI2s(USART_TypeDef *usart, USART_InitI2s_TypeDef *init)
{
  USART_Enable_TypeDef enable;

  /* Make sure the module exists on the selected chip */
  EFM_ASSERT(USART_I2S_VALID(usart));

  /* Override the enable setting. */
  enable            = init->sync.enable;
  init->sync.enable = usartDisable;

  /* Init USART as a sync device. */
  USART_InitSync(usart, &init->sync);

  /* Configure and enable I2CCTRL register acording to selected mode. */
  usart->I2SCTRL = ((uint32_t)init->format) |
                   ((uint32_t)init->justify) |
                   (init->delay    ? USART_I2SCTRL_DELAY    : 0) |
                   (init->dmaSplit ? USART_I2SCTRL_DMASPLIT : 0) |
                   (init->mono     ? USART_I2SCTRL_MONO     : 0) |
                   (USART_I2SCTRL_EN);

  if (enable != usartDisable)
  {
    USART_Enable(usart, enable);
  }
}


/***************************************************************************//**
 * @brief
 *   Initialize automatic transmissions using PRS channel as trigger
 * @note
 *   Initialize USART with USART_Init() before setting up PRS configuration 
 * 
 * @param[in] usart Pointer to USART to configure
 * @param[in] init Pointer to initialization structure
 ******************************************************************************/
void USART_InitPrsTrigger(USART_TypeDef *usart, const USART_PrsTriggerInit_TypeDef *init)
{
  uint32_t trigctrl;

  /* Clear values that will be reconfigured  */
  trigctrl = usart->TRIGCTRL & ~(_USART_TRIGCTRL_RXTEN_MASK|
                                 _USART_TRIGCTRL_TXTEN_MASK|
#if defined(_EFM32_GIANT_FAMILY)
                                 _USART_TRIGCTRL_AUTOTXTEN_MASK|
#endif
                                 _USART_TRIGCTRL_TSEL_MASK);

#if defined(_EFM32_GIANT_FAMILY)
  if(init->autoTxTriggerEnable)
  {
    trigctrl |= USART_TRIGCTRL_AUTOTXTEN;
  }
#endif
  if(init->txTriggerEnable)
  {
    trigctrl |= USART_TRIGCTRL_TXTEN;
  }
  if(init->rxTriggerEnable)
  {
    trigctrl |= USART_TRIGCTRL_RXTEN;
  }
  trigctrl |= init->prsTriggerChannel;

  /* Enable new configuration */
  usart->TRIGCTRL = trigctrl;
}
#endif


/***************************************************************************//**
 * @brief
 *   Reset USART/UART to same state as after a HW reset.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 ******************************************************************************/
void USART_Reset(USART_TypeDef *usart)
{
  /* Make sure the module exists on the selected chip */
  EFM_ASSERT(USART_REF_VALID(usart)||UART_REF_VALID(usart));

  /* Make sure disabled first, before resetting other registers */
  usart->CMD = USART_CMD_RXDIS | USART_CMD_TXDIS | USART_CMD_MASTERDIS |
               USART_CMD_RXBLOCKDIS | USART_CMD_TXTRIDIS | USART_CMD_CLEARTX | USART_CMD_CLEARRX;
  usart->CTRL     = _USART_CTRL_RESETVALUE;
  usart->FRAME    = _USART_FRAME_RESETVALUE;
  usart->TRIGCTRL = _USART_TRIGCTRL_RESETVALUE;
  usart->CLKDIV   = _USART_CLKDIV_RESETVALUE;
  usart->IEN      = _USART_IEN_RESETVALUE;
  usart->IFC      = _USART_IFC_MASK;
  usart->ROUTE    = _USART_ROUTE_RESETVALUE;

  if (USART_IRDA_VALID(usart))
  {
    usart->IRCTRL = _USART_IRCTRL_RESETVALUE;
  }

#if defined(_EFM32_GIANT_FAMILY) || defined(_EFM32_TINY_FAMILY)
  usart->INPUT = _USART_INPUT_RESETVALUE;

  if (USART_I2S_VALID(usart))
  {
    usart->I2SCTRL = _USART_I2SCTRL_RESETVALUE;
  }
#endif

  /* Do not reset route register, setting should be done independently */
}


/***************************************************************************//**
 * @brief
 *   Receive one 4-8 bit frame, (or part of 10-16 bit frame).
 *
 * @details
 *   This function is normally used to receive one frame when operating with
 *   frame length 4-8 bits. Please refer to USART_RxExt() for reception of
 *   9 bit frames.
 *
 *   Notice that possible parity/stop bits in asynchronous mode are not
 *   considered part of specified frame bit length.
 *
 * @note
 *   This function will stall if buffer is empty, until data is received.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @return
 *   Data received.
 ******************************************************************************/
uint8_t USART_Rx(USART_TypeDef *usart)
{
  while (!(usart->STATUS & USART_STATUS_RXDATAV))
    ;

  return (uint8_t)(usart->RXDATA);
}


/***************************************************************************//**
 * @brief
 *   Receive two 4-8 bit frames, or one 10-16 bit frame.
 *
 * @details
 *   This function is normally used to receive one frame when operating with
 *   frame length 10-16 bits. Please refer to USART_RxDoubleExt() for reception
 *   of two 9 bit frames.
 *
 *   Notice that possible parity/stop bits in asynchronous mode are not
 *   considered part of specified frame bit length.
 *
 * @note
 *   This function will stall if buffer is empty, until data is received.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @return
 *   Data received.
 ******************************************************************************/
uint16_t USART_RxDouble(USART_TypeDef *usart)
{
  while (!(usart->STATUS & USART_STATUS_RXFULL))
    ;

  return (uint16_t)(usart->RXDOUBLE);
}


/***************************************************************************//**
 * @brief
 *   Receive two 4-9 bit frames, or one 10-16 bit frame with extended
 *   information.
 *
 * @details
 *   This function is normally used to receive one frame when operating with
 *   frame length 10-16 bits and additional RX status information is required.
 *
 *   Notice that possible parity/stop bits in asynchronous mode are not
 *   considered part of specified frame bit length.
 *
 * @note
 *   This function will stall if buffer is empty, until data is received.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @return
 *   Data received.
 ******************************************************************************/
uint32_t USART_RxDoubleExt(USART_TypeDef *usart)
{
  while (!(usart->STATUS & USART_STATUS_RXFULL))
    ;

  return usart->RXDOUBLEX;
}


/***************************************************************************//**
 * @brief
 *   Receive one 4-9 bit frame, (or part of 10-16 bit frame) with extended
 *   information.
 *
 * @details
 *   This function is normally used to receive one frame when operating with
 *   frame length 4-9 bits and additional RX status information is required.
 *
 *   Notice that possible parity/stop bits in asynchronous mode are not
 *   considered part of specified frame bit length.
 *
 * @note
 *   This function will stall if buffer is empty, until data is received.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @return
 *   Data received.
 ******************************************************************************/
uint16_t USART_RxExt(USART_TypeDef *usart)
{
  while (!(usart->STATUS & USART_STATUS_RXDATAV))
    ;

  return (uint16_t)(usart->RXDATAX);
}


/***************************************************************************//**
 * @brief
 *   Transmit one 4-9 bit frame.
 *
 * @details
 *   Depending on frame length configuration, 4-8 (least significant) bits from
 *   @p data are transmitted. If frame length is 9, 8 bits are transmitted from
 *   @p data and one bit as specified by CTRL register, BIT8DV field. Please
 *   refer to USART_TxExt() for transmitting 9 bit frame with full control of
 *   all 9 bits.
 *
 *   Notice that possible parity/stop bits in asynchronous mode are not
 *   considered part of specified frame bit length.
 *
 * @note
 *   This function will stall if buffer is full, until buffer becomes available.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @param[in] data
 *   Data to transmit. See details above for further info.
 ******************************************************************************/
void USART_Tx(USART_TypeDef *usart, uint8_t data)
{
  /* Check that transmit buffer is empty */
  while (!(usart->STATUS & USART_STATUS_TXBL));
  usart->TXDATA = (uint32_t)data;
}


/***************************************************************************//**
 * @brief
 *   Transmit two 4-9 bit frames, or one 10-16 bit frame.
 *
 * @details
 *   Depending on frame length configuration, 4-8 (least significant) bits from
 *   each byte in @p data are transmitted. If frame length is 9, 8 bits are
 *   transmitted from each byte in @p data adding one bit as specified by CTRL
 *   register, BIT8DV field, to each byte. Please refer to USART_TxDoubleExt()
 *   for transmitting two 9 bit frames with full control of all 9 bits.
 *
 *   If frame length is 10-16, 10-16 (least significant) bits from @p data
 *   are transmitted.
 *
 *   Notice that possible parity/stop bits in asynchronous mode are not
 *   considered part of specified frame bit length.
 *
 * @note
 *   This function will stall if buffer is full, until buffer becomes available.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @param[in] data
 *   Data to transmit, the least significant byte holds the frame transmitted
 *   first. See details above for further info.
 ******************************************************************************/
void USART_TxDouble(USART_TypeDef *usart, uint16_t data)
{
  /* Check that transmit buffer is empty */
  while (!(usart->STATUS & USART_STATUS_TXBL))
    ;
  usart->TXDOUBLE = (uint32_t)data;
}


/***************************************************************************//**
 * @brief
 *   Transmit two 4-9 bit frames, or one 10-16 bit frame with extended control.
 *
 * @details
 *   Notice that possible parity/stop bits in asynchronous mode are not
 *   considered part of specified frame bit length.
 *
 * @note
 *   This function will stall if buffer is full, until buffer becomes available.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @param[in] data
 *   Data to transmit with extended control. Contains two 16 bit words
 *   concatenated. Least significant word holds frame transitted first. If frame
 *   length is 4-9, two frames with 4-9 least significant bits from each 16 bit
 *   word are transmitted.
 * @par
 *   If frame length is 10-16 bits, 8 data bits are taken from the least
 *   significant 16 bit word, and the remaining bits from the other 16 bit word.
 * @par
 *   Additional control bits are available as documented in the EFM32 reference
 *   manual (set to 0 if not used). For 10-16 bit frame length, these control
 *   bits are taken from the most significant 16 bit word.
 ******************************************************************************/
void USART_TxDoubleExt(USART_TypeDef *usart, uint32_t data)
{
  /* Check that transmit buffer is empty */
  while (!(usart->STATUS & USART_STATUS_TXBL))
    ;
  usart->TXDOUBLEX = data;
}


/***************************************************************************//**
 * @brief
 *   Transmit one 4-9 bit frame with extended control.
 *
 * @details
 *   Notice that possible parity/stop bits in asynchronous mode are not
 *   considered part of specified frame bit length.
 *
 * @note
 *   This function will stall if buffer is full, until buffer becomes available.
 *
 * @param[in] usart
 *   Pointer to USART/UART peripheral register block.
 *
 * @param[in] data
 *   Data to transmit with extended control. Least significant bits contains
 *   frame bits, and additional control bits are available as documented in
 *   the EFM32 reference manual (set to 0 if not used).
 ******************************************************************************/
void USART_TxExt(USART_TypeDef *usart, uint16_t data)
{
  /* Check that transmit buffer is empty */
  while (!(usart->STATUS & USART_STATUS_TXBL))
    ;
  usart->TXDATAX = (uint32_t)data;
}


/** @} (end addtogroup USART) */
/** @} (end addtogroup EFM32_Library) */