/**
******************************************************************************
* @file stm32l4xx_hal_flash.h
* @author MCD Application Team
* @brief Header file of FLASH HAL module.
******************************************************************************
* @attention
*
*
© Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32L4xx_HAL_FLASH_H
#define STM32L4xx_HAL_FLASH_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32l4xx_hal_def.h"
/** @addtogroup STM32L4xx_HAL_Driver
* @{
*/
/** @addtogroup FLASH
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup FLASH_Exported_Types FLASH Exported Types
* @{
*/
/**
* @brief FLASH Erase structure definition
*/
typedef struct
{
uint32_t TypeErase; /*!< Mass erase or page erase.
This parameter can be a value of @ref FLASH_Type_Erase */
uint32_t Banks; /*!< Select bank to erase.
This parameter must be a value of @ref FLASH_Banks
(FLASH_BANK_BOTH should be used only for mass erase) */
uint32_t Page; /*!< Initial Flash page to erase when page erase is disabled
This parameter must be a value between 0 and (max number of pages in the bank - 1)
(eg : 255 for 1MB dual bank) */
uint32_t NbPages; /*!< Number of pages to be erased.
This parameter must be a value between 1 and (max number of pages in the bank - value of initial page)*/
} FLASH_EraseInitTypeDef;
/**
* @brief FLASH Option Bytes Program structure definition
*/
typedef struct
{
uint32_t OptionType; /*!< Option byte to be configured.
This parameter can be a combination of the values of @ref FLASH_OB_Type */
uint32_t WRPArea; /*!< Write protection area to be programmed (used for OPTIONBYTE_WRP).
Only one WRP area could be programmed at the same time.
This parameter can be value of @ref FLASH_OB_WRP_Area */
uint32_t WRPStartOffset; /*!< Write protection start offset (used for OPTIONBYTE_WRP).
This parameter must be a value between 0 and (max number of pages in the bank - 1)
(eg : 25 for 1MB dual bank) */
uint32_t WRPEndOffset; /*!< Write protection end offset (used for OPTIONBYTE_WRP).
This parameter must be a value between WRPStartOffset and (max number of pages in the bank - 1) */
uint32_t RDPLevel; /*!< Set the read protection level.. (used for OPTIONBYTE_RDP).
This parameter can be a value of @ref FLASH_OB_Read_Protection */
uint32_t USERType; /*!< User option byte(s) to be configured (used for OPTIONBYTE_USER).
This parameter can be a combination of @ref FLASH_OB_USER_Type */
uint32_t USERConfig; /*!< Value of the user option byte (used for OPTIONBYTE_USER).
This parameter can be a combination of @ref FLASH_OB_USER_BOR_LEVEL,
@ref FLASH_OB_USER_nRST_STOP, @ref FLASH_OB_USER_nRST_STANDBY,
@ref FLASH_OB_USER_nRST_SHUTDOWN, @ref FLASH_OB_USER_IWDG_SW,
@ref FLASH_OB_USER_IWDG_STOP, @ref FLASH_OB_USER_IWDG_STANDBY,
@ref FLASH_OB_USER_WWDG_SW, @ref FLASH_OB_USER_BFB2,
@ref FLASH_OB_USER_DUALBANK, @ref FLASH_OB_USER_nBOOT1,
@ref FLASH_OB_USER_SRAM2_PE and @ref FLASH_OB_USER_SRAM2_RST */
uint32_t PCROPConfig; /*!< Configuration of the PCROP (used for OPTIONBYTE_PCROP).
This parameter must be a combination of @ref FLASH_Banks (except FLASH_BANK_BOTH)
and @ref FLASH_OB_PCROP_RDP */
uint32_t PCROPStartAddr; /*!< PCROP Start address (used for OPTIONBYTE_PCROP).
This parameter must be a value between begin and end of bank
=> Be careful of the bank swapping for the address */
uint32_t PCROPEndAddr; /*!< PCROP End address (used for OPTIONBYTE_PCROP).
This parameter must be a value between PCROP Start address and end of bank */
} FLASH_OBProgramInitTypeDef;
/**
* @brief FLASH Procedure structure definition
*/
typedef enum
{
FLASH_PROC_NONE = 0,
FLASH_PROC_PAGE_ERASE,
FLASH_PROC_MASS_ERASE,
FLASH_PROC_PROGRAM,
FLASH_PROC_PROGRAM_LAST
} FLASH_ProcedureTypeDef;
/**
* @brief FLASH Cache structure definition
*/
typedef enum
{
FLASH_CACHE_DISABLED = 0,
FLASH_CACHE_ICACHE_ENABLED,
FLASH_CACHE_DCACHE_ENABLED,
FLASH_CACHE_ICACHE_DCACHE_ENABLED
} FLASH_CacheTypeDef;
/**
* @brief FLASH handle Structure definition
*/
typedef struct
{
HAL_LockTypeDef Lock; /* FLASH locking object */
__IO uint32_t ErrorCode; /* FLASH error code */
__IO FLASH_ProcedureTypeDef ProcedureOnGoing; /* Internal variable to indicate which procedure is ongoing or not in IT context */
__IO uint32_t Address; /* Internal variable to save address selected for program in IT context */
__IO uint32_t Bank; /* Internal variable to save current bank selected during erase in IT context */
__IO uint32_t Page; /* Internal variable to define the current page which is erasing in IT context */
__IO uint32_t NbPagesToErase; /* Internal variable to save the remaining pages to erase in IT context */
__IO FLASH_CacheTypeDef CacheToReactivate; /* Internal variable to indicate which caches should be reactivated */
}FLASH_ProcessTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup FLASH_Exported_Constants FLASH Exported Constants
* @{
*/
/** @defgroup FLASH_Error FLASH Error
* @{
*/
#define HAL_FLASH_ERROR_NONE 0x00000000U
#define HAL_FLASH_ERROR_OP FLASH_FLAG_OPERR
#define HAL_FLASH_ERROR_PROG FLASH_FLAG_PROGERR
#define HAL_FLASH_ERROR_WRP FLASH_FLAG_WRPERR
#define HAL_FLASH_ERROR_PGA FLASH_FLAG_PGAERR
#define HAL_FLASH_ERROR_SIZ FLASH_FLAG_SIZERR
#define HAL_FLASH_ERROR_PGS FLASH_FLAG_PGSERR
#define HAL_FLASH_ERROR_MIS FLASH_FLAG_MISERR
#define HAL_FLASH_ERROR_FAST FLASH_FLAG_FASTERR
#define HAL_FLASH_ERROR_RD FLASH_FLAG_RDERR
#define HAL_FLASH_ERROR_OPTV FLASH_FLAG_OPTVERR
#define HAL_FLASH_ERROR_ECCC FLASH_FLAG_ECCC
#define HAL_FLASH_ERROR_ECCD FLASH_FLAG_ECCD
#if defined (STM32L412xx) || defined (STM32L422xx) || defined (STM32L431xx) || defined (STM32L432xx) || defined (STM32L433xx) || defined (STM32L442xx) || \
defined (STM32L443xx) || defined (STM32L451xx) || defined (STM32L452xx) || defined (STM32L462xx) || defined (STM32L496xx) || defined (STM32L4A6xx) || \
defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || \
defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define HAL_FLASH_ERROR_PEMPTY FLASH_FLAG_PEMPTY
#endif
/**
* @}
*/
/** @defgroup FLASH_Type_Erase FLASH Erase Type
* @{
*/
#define FLASH_TYPEERASE_PAGES ((uint32_t)0x00) /*!> 24) /*!< ECC Correction Interrupt source */
/**
* @}
*/
/* Exported macros -----------------------------------------------------------*/
/** @defgroup FLASH_Exported_Macros FLASH Exported Macros
* @brief macros to control FLASH features
* @{
*/
/**
* @brief Set the FLASH Latency.
* @param __LATENCY__ FLASH Latency
* This parameter can be one of the following values :
* @arg FLASH_LATENCY_0: FLASH Zero wait state
* @arg FLASH_LATENCY_1: FLASH One wait state
* @arg FLASH_LATENCY_2: FLASH Two wait states
* @arg FLASH_LATENCY_3: FLASH Three wait states
* @arg FLASH_LATENCY_4: FLASH Four wait states
* @retval None
*/
#define __HAL_FLASH_SET_LATENCY(__LATENCY__) (MODIFY_REG(FLASH->ACR, FLASH_ACR_LATENCY, (__LATENCY__)))
/**
* @brief Get the FLASH Latency.
* @retval FLASH Latency
* This parameter can be one of the following values :
* @arg FLASH_LATENCY_0: FLASH Zero wait state
* @arg FLASH_LATENCY_1: FLASH One wait state
* @arg FLASH_LATENCY_2: FLASH Two wait states
* @arg FLASH_LATENCY_3: FLASH Three wait states
* @arg FLASH_LATENCY_4: FLASH Four wait states
*/
#define __HAL_FLASH_GET_LATENCY() READ_BIT(FLASH->ACR, FLASH_ACR_LATENCY)
/**
* @brief Enable the FLASH prefetch buffer.
* @retval None
*/
#define __HAL_FLASH_PREFETCH_BUFFER_ENABLE() SET_BIT(FLASH->ACR, FLASH_ACR_PRFTEN)
/**
* @brief Disable the FLASH prefetch buffer.
* @retval None
*/
#define __HAL_FLASH_PREFETCH_BUFFER_DISABLE() CLEAR_BIT(FLASH->ACR, FLASH_ACR_PRFTEN)
/**
* @brief Enable the FLASH instruction cache.
* @retval none
*/
#define __HAL_FLASH_INSTRUCTION_CACHE_ENABLE() SET_BIT(FLASH->ACR, FLASH_ACR_ICEN)
/**
* @brief Disable the FLASH instruction cache.
* @retval none
*/
#define __HAL_FLASH_INSTRUCTION_CACHE_DISABLE() CLEAR_BIT(FLASH->ACR, FLASH_ACR_ICEN)
/**
* @brief Enable the FLASH data cache.
* @retval none
*/
#define __HAL_FLASH_DATA_CACHE_ENABLE() SET_BIT(FLASH->ACR, FLASH_ACR_DCEN)
/**
* @brief Disable the FLASH data cache.
* @retval none
*/
#define __HAL_FLASH_DATA_CACHE_DISABLE() CLEAR_BIT(FLASH->ACR, FLASH_ACR_DCEN)
/**
* @brief Reset the FLASH instruction Cache.
* @note This function must be used only when the Instruction Cache is disabled.
* @retval None
*/
#define __HAL_FLASH_INSTRUCTION_CACHE_RESET() do { SET_BIT(FLASH->ACR, FLASH_ACR_ICRST); \
CLEAR_BIT(FLASH->ACR, FLASH_ACR_ICRST); \
} while (0)
/**
* @brief Reset the FLASH data Cache.
* @note This function must be used only when the data Cache is disabled.
* @retval None
*/
#define __HAL_FLASH_DATA_CACHE_RESET() do { SET_BIT(FLASH->ACR, FLASH_ACR_DCRST); \
CLEAR_BIT(FLASH->ACR, FLASH_ACR_DCRST); \
} while (0)
/**
* @brief Enable the FLASH power down during Low-power run mode.
* @note Writing this bit to 0 this bit, automatically the keys are
* loss and a new unlock sequence is necessary to re-write it to 1.
*/
#define __HAL_FLASH_POWER_DOWN_ENABLE() do { WRITE_REG(FLASH->PDKEYR, FLASH_PDKEY1); \
WRITE_REG(FLASH->PDKEYR, FLASH_PDKEY2); \
SET_BIT(FLASH->ACR, FLASH_ACR_RUN_PD); \
} while (0)
/**
* @brief Disable the FLASH power down during Low-power run mode.
* @note Writing this bit to 0 this bit, automatically the keys are
* loss and a new unlock sequence is necessary to re-write it to 1.
*/
#define __HAL_FLASH_POWER_DOWN_DISABLE() do { WRITE_REG(FLASH->PDKEYR, FLASH_PDKEY1); \
WRITE_REG(FLASH->PDKEYR, FLASH_PDKEY2); \
CLEAR_BIT(FLASH->ACR, FLASH_ACR_RUN_PD); \
} while (0)
/**
* @brief Enable the FLASH power down during Low-Power sleep mode
* @retval none
*/
#define __HAL_FLASH_SLEEP_POWERDOWN_ENABLE() SET_BIT(FLASH->ACR, FLASH_ACR_SLEEP_PD)
/**
* @brief Disable the FLASH power down during Low-Power sleep mode
* @retval none
*/
#define __HAL_FLASH_SLEEP_POWERDOWN_DISABLE() CLEAR_BIT(FLASH->ACR, FLASH_ACR_SLEEP_PD)
/**
* @}
*/
/** @defgroup FLASH_Interrupt FLASH Interrupts Macros
* @brief macros to handle FLASH interrupts
* @{
*/
/**
* @brief Enable the specified FLASH interrupt.
* @param __INTERRUPT__ FLASH interrupt
* This parameter can be any combination of the following values:
* @arg FLASH_IT_EOP: End of FLASH Operation Interrupt
* @arg FLASH_IT_OPERR: Error Interrupt
* @arg FLASH_IT_RDERR: PCROP Read Error Interrupt
* @arg FLASH_IT_ECCC: ECC Correction Interrupt
* @retval none
*/
#define __HAL_FLASH_ENABLE_IT(__INTERRUPT__) do { if(((__INTERRUPT__) & FLASH_IT_ECCC) != 0U) { SET_BIT(FLASH->ECCR, FLASH_ECCR_ECCIE); }\
if(((__INTERRUPT__) & (~FLASH_IT_ECCC)) != 0U) { SET_BIT(FLASH->CR, ((__INTERRUPT__) & (~FLASH_IT_ECCC))); }\
} while(0)
/**
* @brief Disable the specified FLASH interrupt.
* @param __INTERRUPT__ FLASH interrupt
* This parameter can be any combination of the following values:
* @arg FLASH_IT_EOP: End of FLASH Operation Interrupt
* @arg FLASH_IT_OPERR: Error Interrupt
* @arg FLASH_IT_RDERR: PCROP Read Error Interrupt
* @arg FLASH_IT_ECCC: ECC Correction Interrupt
* @retval none
*/
#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__) do { if(((__INTERRUPT__) & FLASH_IT_ECCC) != 0U) { CLEAR_BIT(FLASH->ECCR, FLASH_ECCR_ECCIE); }\
if(((__INTERRUPT__) & (~FLASH_IT_ECCC)) != 0U) { CLEAR_BIT(FLASH->CR, ((__INTERRUPT__) & (~FLASH_IT_ECCC))); }\
} while(0)
/**
* @brief Check whether the specified FLASH flag is set or not.
* @param __FLAG__ specifies the FLASH flag to check.
* This parameter can be one of the following values:
* @arg FLASH_FLAG_EOP: FLASH End of Operation flag
* @arg FLASH_FLAG_OPERR: FLASH Operation error flag
* @arg FLASH_FLAG_PROGERR: FLASH Programming error flag
* @arg FLASH_FLAG_WRPERR: FLASH Write protection error flag
* @arg FLASH_FLAG_PGAERR: FLASH Programming alignment error flag
* @arg FLASH_FLAG_SIZERR: FLASH Size error flag
* @arg FLASH_FLAG_PGSERR: FLASH Programming sequence error flag
* @arg FLASH_FLAG_MISERR: FLASH Fast programming data miss error flag
* @arg FLASH_FLAG_FASTERR: FLASH Fast programming error flag
* @arg FLASH_FLAG_RDERR: FLASH PCROP read error flag
* @arg FLASH_FLAG_OPTVERR: FLASH Option validity error flag
* @arg FLASH_FLAG_BSY: FLASH write/erase operations in progress flag
* @arg FLASH_FLAG_PEMPTY : FLASH Boot from not programmed flash (apply only for STM32L43x/STM32L44x devices)
* @arg FLASH_FLAG_ECCC: FLASH one ECC error has been detected and corrected
* @arg FLASH_FLAG_ECCD: FLASH two ECC errors have been detected
* @retval The new state of FLASH_FLAG (SET or RESET).
*/
#define __HAL_FLASH_GET_FLAG(__FLAG__) ((((__FLAG__) & FLASH_FLAG_ECCR_ERRORS) != 0U) ? \
(READ_BIT(FLASH->ECCR, (__FLAG__)) != 0U) : \
(READ_BIT(FLASH->SR, (__FLAG__)) != 0U))
/**
* @brief Clear the FLASH's pending flags.
* @param __FLAG__ specifies the FLASH flags to clear.
* This parameter can be any combination of the following values:
* @arg FLASH_FLAG_EOP: FLASH End of Operation flag
* @arg FLASH_FLAG_OPERR: FLASH Operation error flag
* @arg FLASH_FLAG_PROGERR: FLASH Programming error flag
* @arg FLASH_FLAG_WRPERR: FLASH Write protection error flag
* @arg FLASH_FLAG_PGAERR: FLASH Programming alignment error flag
* @arg FLASH_FLAG_SIZERR: FLASH Size error flag
* @arg FLASH_FLAG_PGSERR: FLASH Programming sequence error flag
* @arg FLASH_FLAG_MISERR: FLASH Fast programming data miss error flag
* @arg FLASH_FLAG_FASTERR: FLASH Fast programming error flag
* @arg FLASH_FLAG_RDERR: FLASH PCROP read error flag
* @arg FLASH_FLAG_OPTVERR: FLASH Option validity error flag
* @arg FLASH_FLAG_ECCC: FLASH one ECC error has been detected and corrected
* @arg FLASH_FLAG_ECCD: FLASH two ECC errors have been detected
* @arg FLASH_FLAG_ALL_ERRORS: FLASH All errors flags
* @retval None
*/
#define __HAL_FLASH_CLEAR_FLAG(__FLAG__) do { if(((__FLAG__) & FLASH_FLAG_ECCR_ERRORS) != 0U) { SET_BIT(FLASH->ECCR, ((__FLAG__) & FLASH_FLAG_ECCR_ERRORS)); }\
if(((__FLAG__) & ~(FLASH_FLAG_ECCR_ERRORS)) != 0U) { WRITE_REG(FLASH->SR, ((__FLAG__) & ~(FLASH_FLAG_ECCR_ERRORS))); }\
} while(0)
/**
* @}
*/
/* Include FLASH HAL Extended module */
#include "stm32l4xx_hal_flash_ex.h"
#include "stm32l4xx_hal_flash_ramfunc.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup FLASH_Exported_Functions
* @{
*/
/* Program operation functions ***********************************************/
/** @addtogroup FLASH_Exported_Functions_Group1
* @{
*/
HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data);
HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data);
/* FLASH IRQ handler method */
void HAL_FLASH_IRQHandler(void);
/* Callbacks in non blocking modes */
void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue);
void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue);
/**
* @}
*/
/* Peripheral Control functions **********************************************/
/** @addtogroup FLASH_Exported_Functions_Group2
* @{
*/
HAL_StatusTypeDef HAL_FLASH_Unlock(void);
HAL_StatusTypeDef HAL_FLASH_Lock(void);
/* Option bytes control */
HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void);
HAL_StatusTypeDef HAL_FLASH_OB_Lock(void);
HAL_StatusTypeDef HAL_FLASH_OB_Launch(void);
/**
* @}
*/
/* Peripheral State functions ************************************************/
/** @addtogroup FLASH_Exported_Functions_Group3
* @{
*/
uint32_t HAL_FLASH_GetError(void);
/**
* @}
*/
/**
* @}
*/
/* Private variables ---------------------------------------------------------*/
/** @addtogroup FLASH_Private_Variables FLASH Private Variables
* @{
*/
extern FLASH_ProcessTypeDef pFlash;
/**
* @}
*/
/* Private function ----------------------------------------------------------*/
/** @addtogroup FLASH_Private_Functions FLASH Private Functions
* @{
*/
HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout);
/**
* @}
*/
/* Private constants --------------------------------------------------------*/
/** @defgroup FLASH_Private_Constants FLASH Private Constants
* @{
*/
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || \
defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define FLASH_BANK_SIZE (FLASH_SIZE >> 1U)
#else
#define FLASH_BANK_SIZE (FLASH_SIZE)
#endif
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define FLASH_PAGE_SIZE ((uint32_t)0x1000)
#define FLASH_PAGE_SIZE_128_BITS ((uint32_t)0x2000)
#else
#define FLASH_PAGE_SIZE ((uint32_t)0x800)
#endif
#define FLASH_TIMEOUT_VALUE ((uint32_t)50000)/* 50 s */
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup FLASH_Private_Macros FLASH Private Macros
* @{
*/
#define IS_FLASH_TYPEERASE(VALUE) (((VALUE) == FLASH_TYPEERASE_PAGES) || \
((VALUE) == FLASH_TYPEERASE_MASSERASE))
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || \
defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_FLASH_BANK(BANK) (((BANK) == FLASH_BANK_1) || \
((BANK) == FLASH_BANK_2) || \
((BANK) == FLASH_BANK_BOTH))
#define IS_FLASH_BANK_EXCLUSIVE(BANK) (((BANK) == FLASH_BANK_1) || \
((BANK) == FLASH_BANK_2))
#else
#define IS_FLASH_BANK(BANK) ((BANK) == FLASH_BANK_1)
#define IS_FLASH_BANK_EXCLUSIVE(BANK) ((BANK) == FLASH_BANK_1)
#endif
#define IS_FLASH_TYPEPROGRAM(VALUE) (((VALUE) == FLASH_TYPEPROGRAM_DOUBLEWORD) || \
((VALUE) == FLASH_TYPEPROGRAM_FAST) || \
((VALUE) == FLASH_TYPEPROGRAM_FAST_AND_LAST))
#if defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_FLASH_MAIN_MEM_ADDRESS(ADDRESS) (((ADDRESS) >= (FLASH_BASE)) && ((ADDRESS) <= (FLASH_BASE+0x1FFFFFU)))
#else
#define IS_FLASH_MAIN_MEM_ADDRESS(ADDRESS) (((ADDRESS) >= (FLASH_BASE)) && ((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x400U) ? \
((ADDRESS) <= (FLASH_BASE+0xFFFFFU)) : ((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x200U) ? \
((ADDRESS) <= (FLASH_BASE+0x7FFFFU)) : ((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x100U) ? \
((ADDRESS) <= (FLASH_BASE+0x3FFFFU)) : ((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x80U) ? \
((ADDRESS) <= (FLASH_BASE+0x1FFFFU)) : ((ADDRESS) <= (FLASH_BASE+0xFFFFFU)))))))
#endif
#define IS_FLASH_OTP_ADDRESS(ADDRESS) (((ADDRESS) >= 0x1FFF7000U) && ((ADDRESS) <= 0x1FFF73FFU))
#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) ((IS_FLASH_MAIN_MEM_ADDRESS(ADDRESS)) || (IS_FLASH_OTP_ADDRESS(ADDRESS)))
#if defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_FLASH_PAGE(PAGE) ((PAGE) < 256U)
#elif defined(STM32L471xx) || defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) || defined(STM32L496xx) || defined(STM32L4A6xx) || defined (STM32L4P5xx) || defined (STM32L4Q5xx)
#define IS_FLASH_PAGE(PAGE) (((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x400U) ? ((PAGE) < 256U) : \
((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x200U) ? ((PAGE) < 128U) : \
((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x100U) ? ((PAGE) < 64U) : \
((PAGE) < 256U)))))
#elif defined (STM32L451xx) || defined (STM32L452xx) || defined (STM32L462xx)
#define IS_FLASH_PAGE(PAGE) (((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x200U) ? ((PAGE) < 256U) : \
((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x100U) ? ((PAGE) < 128U) : \
((PAGE) < 256U))))
#else
#define IS_FLASH_PAGE(PAGE) (((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x100U) ? ((PAGE) < 128U) : \
((((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) & (0x0FFFU)) == 0x80U) ? ((PAGE) < 64U) : \
((PAGE) < 128U))))
#endif
#define IS_OPTIONBYTE(VALUE) (((VALUE) <= (OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER | OPTIONBYTE_PCROP)))
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || \
defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_OB_WRPAREA(VALUE) (((VALUE) == OB_WRPAREA_BANK1_AREAA) || ((VALUE) == OB_WRPAREA_BANK1_AREAB) || \
((VALUE) == OB_WRPAREA_BANK2_AREAA) || ((VALUE) == OB_WRPAREA_BANK2_AREAB))
#else
#define IS_OB_WRPAREA(VALUE) (((VALUE) == OB_WRPAREA_BANK1_AREAA) || ((VALUE) == OB_WRPAREA_BANK1_AREAB))
#endif
#define IS_OB_RDP_LEVEL(LEVEL) (((LEVEL) == OB_RDP_LEVEL_0) ||\
((LEVEL) == OB_RDP_LEVEL_1)/* ||\
((LEVEL) == OB_RDP_LEVEL_2)*/)
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_OB_USER_TYPE(TYPE) (((TYPE) <= (uint32_t)0xFFFFU) && ((TYPE) != 0U))
#elif defined(STM32L471xx) || defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) || defined(STM32L496xx) || defined(STM32L4A6xx)
#define IS_OB_USER_TYPE(TYPE) (((TYPE) <= (uint32_t)0x1FFFU) && ((TYPE) != 0U))
#else
#define IS_OB_USER_TYPE(TYPE) (((TYPE) <= (uint32_t)0x7E7FU) && ((TYPE) != 0U) && (((TYPE)&0x0180U) == 0U))
#endif
#define IS_OB_USER_BOR_LEVEL(LEVEL) (((LEVEL) == OB_BOR_LEVEL_0) || ((LEVEL) == OB_BOR_LEVEL_1) || \
((LEVEL) == OB_BOR_LEVEL_2) || ((LEVEL) == OB_BOR_LEVEL_3) || \
((LEVEL) == OB_BOR_LEVEL_4))
#define IS_OB_USER_STOP(VALUE) (((VALUE) == OB_STOP_RST) || ((VALUE) == OB_STOP_NORST))
#define IS_OB_USER_STANDBY(VALUE) (((VALUE) == OB_STANDBY_RST) || ((VALUE) == OB_STANDBY_NORST))
#define IS_OB_USER_SHUTDOWN(VALUE) (((VALUE) == OB_SHUTDOWN_RST) || ((VALUE) == OB_SHUTDOWN_NORST))
#define IS_OB_USER_IWDG(VALUE) (((VALUE) == OB_IWDG_HW) || ((VALUE) == OB_IWDG_SW))
#define IS_OB_USER_IWDG_STOP(VALUE) (((VALUE) == OB_IWDG_STOP_FREEZE) || ((VALUE) == OB_IWDG_STOP_RUN))
#define IS_OB_USER_IWDG_STDBY(VALUE) (((VALUE) == OB_IWDG_STDBY_FREEZE) || ((VALUE) == OB_IWDG_STDBY_RUN))
#define IS_OB_USER_WWDG(VALUE) (((VALUE) == OB_WWDG_HW) || ((VALUE) == OB_WWDG_SW))
#if defined (STM32L471xx) || defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || \
defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_OB_USER_BFB2(VALUE) (((VALUE) == OB_BFB2_DISABLE) || ((VALUE) == OB_BFB2_ENABLE))
#define IS_OB_USER_DUALBANK(VALUE) (((VALUE) == OB_DUALBANK_SINGLE) || ((VALUE) == OB_DUALBANK_DUAL))
#endif
#if defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_OB_USER_DBANK(VALUE) (((VALUE) == OB_DBANK_128_BITS) || ((VALUE) == OB_DBANK_64_BITS))
#endif
#define IS_OB_USER_BOOT1(VALUE) (((VALUE) == OB_BOOT1_SRAM) || ((VALUE) == OB_BOOT1_SYSTEM))
#define IS_OB_USER_SRAM2_PARITY(VALUE) (((VALUE) == OB_SRAM2_PARITY_ENABLE) || ((VALUE) == OB_SRAM2_PARITY_DISABLE))
#define IS_OB_USER_SRAM2_RST(VALUE) (((VALUE) == OB_SRAM2_RST_ERASE) || ((VALUE) == OB_SRAM2_RST_NOT_ERASE))
#if defined (STM32L412xx) || defined (STM32L422xx) || defined (STM32L431xx) || defined (STM32L432xx) || defined (STM32L433xx) || \
defined (STM32L442xx) || defined (STM32L443xx) || defined (STM32L451xx) || defined (STM32L452xx) || defined (STM32L462xx) || \
defined (STM32L496xx) || defined (STM32L4A6xx) || defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || \
defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_OB_USER_SWBOOT0(VALUE) (((VALUE) == OB_BOOT0_FROM_OB) || ((VALUE) == OB_BOOT0_FROM_PIN))
#define IS_OB_USER_BOOT0(VALUE) (((VALUE) == OB_BOOT0_RESET) || ((VALUE) == OB_BOOT0_SET))
#endif
#define IS_OB_PCROP_RDP(VALUE) (((VALUE) == OB_PCROP_RDP_NOT_ERASE) || ((VALUE) == OB_PCROP_RDP_ERASE))
#if defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx)
#define IS_FLASH_LATENCY(LATENCY) (((LATENCY) == FLASH_LATENCY_0) || ((LATENCY) == FLASH_LATENCY_1) || \
((LATENCY) == FLASH_LATENCY_2) || ((LATENCY) == FLASH_LATENCY_3) || \
((LATENCY) == FLASH_LATENCY_4) || ((LATENCY) == FLASH_LATENCY_5) || \
((LATENCY) == FLASH_LATENCY_6) || ((LATENCY) == FLASH_LATENCY_7) || \
((LATENCY) == FLASH_LATENCY_8) || ((LATENCY) == FLASH_LATENCY_9) || \
((LATENCY) == FLASH_LATENCY_10) || ((LATENCY) == FLASH_LATENCY_11) || \
((LATENCY) == FLASH_LATENCY_12) || ((LATENCY) == FLASH_LATENCY_13) || \
((LATENCY) == FLASH_LATENCY_14) || ((LATENCY) == FLASH_LATENCY_15))
#else
#define IS_FLASH_LATENCY(LATENCY) (((LATENCY) == FLASH_LATENCY_0) || \
((LATENCY) == FLASH_LATENCY_1) || \
((LATENCY) == FLASH_LATENCY_2) || \
((LATENCY) == FLASH_LATENCY_3) || \
((LATENCY) == FLASH_LATENCY_4))
#endif
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* STM32L4xx_HAL_FLASH_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/