/** ****************************************************************************** * @file usb_conf.h * @author MCD Application Team * @version V1.1.0 * @date 19-March-2012 * @brief General low level driver configuration ****************************************************************************** * @attention * *

© COPYRIGHT 2012 STMicroelectronics

* * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); * You may not use this file except in compliance with the License. * You may obtain a copy of the License at: * * http://www.st.com/software_license_agreement_liberty_v2 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __USB_CONF__H__ #define __USB_CONF__H__ /* Includes ------------------------------------------------------------------*/ #include "stm32f4xx.h" /** @addtogroup USB_OTG_DRIVER * @{ */ /** @defgroup USB_CONF * @brief USB low level driver configuration file * @{ */ /** @defgroup USB_CONF_Exported_Defines * @{ */ /* USB Core and PHY interface configuration. Tip: To avoid modifying these defines each time you need to change the USB configuration, you can declare the needed define in your toolchain compiler preprocessor. */ /****************** USB OTG FS PHY CONFIGURATION ******************************* * The USB OTG FS Core supports one on-chip Full Speed PHY. * * The USE_EMBEDDED_PHY symbol is defined in the project compiler preprocessor * when FS core is used. *******************************************************************************/ #ifndef USE_USB_OTG_FS //#define USE_USB_OTG_FS #endif /* USE_USB_OTG_FS */ #ifdef USE_USB_OTG_FS #define USB_OTG_FS_CORE #endif /****************** USB OTG HS PHY CONFIGURATION ******************************* * The USB OTG HS Core supports two PHY interfaces: * (i) An ULPI interface for the external High Speed PHY: the USB HS Core will * operate in High speed mode * (ii) An on-chip Full Speed PHY: the USB HS Core will operate in Full speed mode * * You can select the PHY to be used using one of these two defines: * (i) USE_ULPI_PHY: if the USB OTG HS Core is to be used in High speed mode * (ii) USE_EMBEDDED_PHY: if the USB OTG HS Core is to be used in Full speed mode * * Notes: * - The USE_ULPI_PHY symbol is defined in the project compiler preprocessor as * default PHY when HS core is used. * - On STM322xG-EVAL and STM324xG-EVAL boards, only configuration(i) is available. * Configuration (ii) need a different hardware, for more details refer to your * STM32 device datasheet. *******************************************************************************/ #ifndef USE_USB_OTG_HS //#define USE_USB_OTG_HS #endif /* USE_USB_OTG_HS */ #ifndef USE_ULPI_PHY //#define USE_ULPI_PHY #endif /* USE_ULPI_PHY */ #ifndef USE_EMBEDDED_PHY //#define USE_EMBEDDED_PHY #endif /* USE_EMBEDDED_PHY */ #ifdef USE_USB_OTG_HS #define USB_OTG_HS_CORE #endif /******************************************************************************* * FIFO Size Configuration in Device mode * * (i) Receive data FIFO size = RAM for setup packets + * OUT endpoint control information + * data OUT packets + miscellaneous * Space = ONE 32-bits words * --> RAM for setup packets = 10 spaces * (n is the nbr of CTRL EPs the device core supports) * --> OUT EP CTRL info = 1 space * (one space for status information written to the FIFO along with each * received packet) * --> data OUT packets = (Largest Packet Size / 4) + 1 spaces * (MINIMUM to receive packets) * --> OR data OUT packets = at least 2*(Largest Packet Size / 4) + 1 spaces * (if high-bandwidth EP is enabled or multiple isochronous EPs) * --> miscellaneous = 1 space per OUT EP * (one space for transfer complete status information also pushed to the * FIFO with each endpoint's last packet) * * (ii)MINIMUM RAM space required for each IN EP Tx FIFO = MAX packet size for * that particular IN EP. More space allocated in the IN EP Tx FIFO results * in a better performance on the USB and can hide latencies on the AHB. * * (iii) TXn min size = 16 words. (n : Transmit FIFO index) * (iv) When a TxFIFO is not used, the Configuration should be as follows: * case 1 : n > m and Txn is not used (n,m : Transmit FIFO indexes) * --> Txm can use the space allocated for Txn. * case2 : n < m and Txn is not used (n,m : Transmit FIFO indexes) * --> Txn should be configured with the minimum space of 16 words * (v) The FIFO is used optimally when used TxFIFOs are allocated in the top * of the FIFO.Ex: use EP1 and EP2 as IN instead of EP1 and EP3 as IN ones. * (vi) In HS case 12 FIFO locations should be reserved for internal DMA registers * so total FIFO size should be 1012 Only instead of 1024 *******************************************************************************/ /****************** USB OTG HS CONFIGURATION **********************************/ #ifdef USB_OTG_HS_CORE #define RX_FIFO_HS_SIZE 512 #define TX0_FIFO_HS_SIZE 64 #define TX1_FIFO_HS_SIZE 372 #define TX2_FIFO_HS_SIZE 64 #define TX3_FIFO_HS_SIZE 0 #define TX4_FIFO_HS_SIZE 0 #define TX5_FIFO_HS_SIZE 0 // #define USB_OTG_HS_SOF_OUTPUT_ENABLED #ifdef USE_ULPI_PHY #define USB_OTG_ULPI_PHY_ENABLED #endif #ifdef USE_EMBEDDED_PHY #define USB_OTG_EMBEDDED_PHY_ENABLED /* wakeup is working only when HS core is configured in FS mode */ #define USB_OTG_HS_LOW_PWR_MGMT_SUPPORT #endif /* #define USB_OTG_HS_INTERNAL_DMA_ENABLED */ /* Be aware that enabling DMA mode will result in data being sent only by multiple of 4 packet sizes. This is due to the fact that USB DMA does not allow sending data from non word-aligned addresses. For this specific application, it is advised to not enable this option unless required. */ #define USB_OTG_HS_DEDICATED_EP1_ENABLED #endif /****************** USB OTG FS CONFIGURATION **********************************/ #ifdef USB_OTG_FS_CORE #define RX_FIFO_FS_SIZE 128 #define TX0_FIFO_FS_SIZE 32 #define TX1_FIFO_FS_SIZE 128 #define TX2_FIFO_FS_SIZE 32 #define TX3_FIFO_FS_SIZE 0 // #define USB_OTG_FS_LOW_PWR_MGMT_SUPPORT // #define USB_OTG_FS_SOF_OUTPUT_ENABLED #endif /****************** USB OTG MISC CONFIGURATION ********************************/ #define VBUS_SENSING_ENABLED /****************** USB OTG MODE CONFIGURATION ********************************/ //#define USE_HOST_MODE #define USE_DEVICE_MODE //#define USE_OTG_MODE #ifndef USB_OTG_FS_CORE #ifndef USB_OTG_HS_CORE #error "USB_OTG_HS_CORE or USB_OTG_FS_CORE should be defined" #endif #endif #ifndef USE_DEVICE_MODE #ifndef USE_HOST_MODE #error "USE_DEVICE_MODE or USE_HOST_MODE should be defined" #endif #endif #ifndef USE_USB_OTG_HS #ifndef USE_USB_OTG_FS #error "USE_USB_OTG_HS or USE_USB_OTG_FS should be defined" #endif #else //USE_USB_OTG_HS #ifndef USE_ULPI_PHY #ifndef USE_EMBEDDED_PHY #error "USE_ULPI_PHY or USE_EMBEDDED_PHY should be defined" #endif #endif #endif /****************** C Compilers dependant keywords ****************************/ /* In HS mode and when the DMA is used, all variables and data structures dealing with the DMA during the transaction process should be 4-bytes aligned */ #ifdef USB_OTG_HS_INTERNAL_DMA_ENABLED #if defined (__GNUC__) /* GNU Compiler */ #define __ALIGN_END __attribute__ ((aligned (4))) #define __ALIGN_BEGIN #else #define __ALIGN_END #if defined (__CC_ARM) /* ARM Compiler */ #define __ALIGN_BEGIN __align(4) #elif defined (__ICCARM__) /* IAR Compiler */ #define __ALIGN_BEGIN #elif defined (__TASKING__) /* TASKING Compiler */ #define __ALIGN_BEGIN __align(4) #endif /* __CC_ARM */ #endif /* __GNUC__ */ #else #define __ALIGN_BEGIN #define __ALIGN_END #endif /* USB_OTG_HS_INTERNAL_DMA_ENABLED */ /* __packed keyword used to decrease the data type alignment to 1-byte */ #if defined (__CC_ARM) /* ARM Compiler */ #define __packed __packed #elif defined (__ICCARM__) /* IAR Compiler */ #define __packed __packed #elif defined ( __GNUC__ ) /* GNU Compiler */ #define __packed __attribute__ ((__packed__)) #elif defined (__TASKING__) /* TASKING Compiler */ #define __packed __unaligned #endif /* __CC_ARM */ /** * @} */ /** @defgroup USB_CONF_Exported_Types * @{ */ /** * @} */ /** @defgroup USB_CONF_Exported_Macros * @{ */ /** * @} */ /** @defgroup USB_CONF_Exported_Variables * @{ */ /** * @} */ /** @defgroup USB_CONF_Exported_FunctionsPrototype * @{ */ /** * @} */ #endif //__USB_CONF__H__ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/