The following patches unfortunately didn't hit the kernel stable
branches yet, therefore cherrypicking them for OpenWRT here:
* bridge: fix netfilter/NF_BR_LOCAL_OUT for own, locally generated queries
* bridge: multicast: enable snooping on general queries only
* bridge: multicast: add sanity check for general query destination
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Backport of r43841
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@44049 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Backport of r42897
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43867 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r43736
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43737 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r43624
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43683 3c298f89-4303-0410-b956-a3cf2f4a3e73
The cpu port is at 8, not 5.
Fixes#18406.
Backport of r43379.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43380 3c298f89-4303-0410-b956-a3cf2f4a3e73
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43166 3c298f89-4303-0410-b956-a3cf2f4a3e73
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43165 3c298f89-4303-0410-b956-a3cf2f4a3e73
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43164 3c298f89-4303-0410-b956-a3cf2f4a3e73
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43163 3c298f89-4303-0410-b956-a3cf2f4a3e73
MIPS: Fix rtlx build error.
CC arch/mips/kernel/rtlx.o
/home/ralf/src/linux/upstream-sfr/arch/mips/kernel/rtlx.c: In function ‘file_write’:
/home/ralf/src/linux/upstream-sfr/arch/mips/kernel/rtlx.c:439:23: error: unused variable ‘rt’ [-Werror=unused-variable]
/home/ralf/src/linux/upstream-sfr/arch/mips/kernel/rtlx.c: In function ‘rtlx_module_init’:
/home/ralf/src/linux/upstream-sfr/arch/mips/kernel/rtlx.c:523:3: error: implicit declaration of function ‘set_vi_handler’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
Caused by 496ad9aa8ef448058e36ca7a787c61f2e63f0f54 [new helper:
file_inode(file)].
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43159 3c298f89-4303-0410-b956-a3cf2f4a3e73
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43158 3c298f89-4303-0410-b956-a3cf2f4a3e73
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43157 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r43128
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43129 3c298f89-4303-0410-b956-a3cf2f4a3e73
This works around a bootloader issue where every device
has the same lan/wan-mac 00:04:9f:ef:01:01 - with this patch
we read the macs from config-partition during initial network
setup. We have 9 valid macs stored in the partition, the
1st two are used for the radios, 3 and 4 are now used for WAN/LAN.
on an already setup / running device we can get the real macs with
. /lib/functions.sh
. /lib/functions/system.sh
echo "LAN = $(mtd_get_mac_binary config 338)"
echo "WAN = $(mtd_get_mac_binary config 344)"
see:
https://dev.openwrt.org/ticket/14714
from the ticket / user klondike:
U-Boot passed this commit ecd1a09b81http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-mpc83xx-remove-hardcoded-network-addresses-from-config-files-td44372.html
I suppose to prevent this particular issue, but the WDR4900 may be using an old bootloader still affected.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I have been checking the contents of the dtb on the flash, this particular bit is quite revealing:
ethernet@b0000 {
#address-cells = <0x1>;
#size-cells = <0x1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [00 00 00 00 00 00];
^^^^^^^^^^^^^^^^^
interrupt-parent = <0x2>;
phy-handle = <0x3>;
phy-connection-type = "rgmii-id";
ptimer-handle = <0x4>;
queue-group@0 {
#address-cells = <0x1>;
#size-cells = <0x1>;
reg = <0xb0000 0x1000>;
rx-bit-map = <0xff>;
tx-bit-map = <0xff>;
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
};
};
I also have been checking the live device map to find this:
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b0000/local-mac-address
00000000 00 04 9f ef 01 01 |......|
00000006
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b1000/local-mac-address
*
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b2000/local-mac-address
*
My conclussion is that U-Boot most likely finds the device and (as no valid MAC-address is provided)
falls back to the default MAC provided by the old code, the kernel then receives thee modified
device map from U-Boot and assumes this is the correct MAC for the device despite it obviously isn't.
This can be seen at
target/linux/mpc85xx/patches-3.10/140-powerpc-85xx-tl-wdr4900-v1-support.patch
The enetaddr is filled up by using the device tree data by the process_boot_dtb
function and used by the platform_fixups function to set the eth0 address
(by calling dt_fixup_mac_address_by_alias("ethernet0", enetaddr); ).
But instead we should be used the device address which to my understanding is
provided in the mtd.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
Backport of r43074
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43077 3c298f89-4303-0410-b956-a3cf2f4a3e73
The existance of this new board has been confirmed and tested by the guy on this commit
76fdd8e638
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@43075 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch ports back some fixes of the ad799x driver, which were
committed between 3.10 and 3.15.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42993 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42955
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42956 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change makes the profile of WDR4900 more consistent with other router
specific profiles.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42898 3c298f89-4303-0410-b956-a3cf2f4a3e73
Have gpio driver adopt irqdomain support so that there are
non-overlapping allocations of irq numbers mapped to gpio's.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Backport of r42844
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42847 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch originally failed to combine INTA/B/C/D onto a single ARM CPU
interrupt. Instead, it mapped INTA/B/C and excluded D. This patch
corrects the issue by mapping all four interrupts to the single ARM CPU
interrupt. The original intent of the patch still holds as the newer PCB
take advantage of isolated interrupts. This fix only applies to older
PCB's that do not route INTA/B/C/D to unique external ARM CPU
interrupts.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Backport of r42830
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42846 3c298f89-4303-0410-b956-a3cf2f4a3e73
also fixes a GPIO related regression from the upgrade to 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42829
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42845 3c298f89-4303-0410-b956-a3cf2f4a3e73
this allows people building custom images to use dwc2 instead of dwc_otg
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42801 3c298f89-4303-0410-b956-a3cf2f4a3e73
Kernel modules which are built using the SDK do not have access
to the .vermagic file in the Linux build dir, therefore the
generated .ipk metadata depends on kernel versions like
'3.10.49-1-unknown' which are not satisfiable by the kernel
meta package in the image.
Fix this problem by substituting 'unknown' with the current
version magic in include/kernel.mk when packing the SDK.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Backport of r42590
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42592 3c298f89-4303-0410-b956-a3cf2f4a3e73
both units have a lna/pna combo that the driver so far does not support
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42585 3c298f89-4303-0410-b956-a3cf2f4a3e73
fix inclusion of functions.sh in dsl_fs init script
without this, the following error is seen during build:
./etc/init.d/dsl_fs: line 4: /lib/functions.sh: No such file or directory
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Backport of r42575
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42580 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: John Crispin <blogic@openwrt.org>
Backport of r42544
Backport of r42551
Backport of r42574
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42578 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42457
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42475 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42460
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42461 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: John Crispin <blogic@openwrt.org>
Backport of r42437
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42438 3c298f89-4303-0410-b956-a3cf2f4a3e73
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable. The existing code
however advertieses gigabit capability in the link status word. If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link. This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.
In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.
So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit. This patch implements the
former solution.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Backport of r42432
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42434 3c298f89-4303-0410-b956-a3cf2f4a3e73
The cns3xxx uses irq61 for pcie0_intr which in the case of a PCIe-to-PCI
bridge ends up combining INTA/B/C/D on a single ARM CPU interrupt. This is
not optimal when you have multiple cores. To overcome this limitation an
enhancement was made on newer Laguna PCB's that support miniPCI cards
to route the INTA/B/C/D signals to unique external ARM CPU interrupts which
can help balance CPU core utilization and in some cases increase overall
system performance or responsiveness.
For more details see:
http://trac.gateworks.com/wiki/multicoreprocessing#PCIInterruptsteering
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Backport of r42400
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42402 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42397
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42398 3c298f89-4303-0410-b956-a3cf2f4a3e73
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Backport of r42194
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42395 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Backport of r42130
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42393 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: John Crispin <blogic@openwrt.org>
Backport of r42321
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42391 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bb-rc3 image for the BTHOMEHUBV2B is too big for its
mtd partition. This patch corrects the partition sizes in
the device tree. This patch should really go in before
bb-final, otherwise the BTHOMEHUBV2B images won't be useable.
I do apologise for not spotting this straight away.
Many thanks,
Ben
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Backport of r42316
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42386 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: John Crispin <blogic@openwrt.org>
Backport of r42293
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42385 3c298f89-4303-0410-b956-a3cf2f4a3e73
the ohci phy was not reset properly
Signed-off-by: John Crispin <blogic@openwrt.org>
Backport of r42290
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42384 3c298f89-4303-0410-b956-a3cf2f4a3e73
fix the default package selection
Signed-off-by: John Crispin <blogic@openwrt.org>
Backport of r42289
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42383 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enables the second SPI as spidev and also fixes some typos.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport of r42277
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42378 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for setting SPI_CS1 as Chip Select, Watchdog reset output and GPIO#27.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport of r41938
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42377 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport of r41939
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42376 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on Jon Smirl's patch with the following changes:
- Set CS polarity as low by default.
- Add support for changing CS polarity.
- Add support for changing LSB/MSB.
- Add support for changing SPI mode.
- Fix indentations.
I tested it on a VoCore. Works fine connected to a second flash, but fails to detect MMC/SD cards due to SPI clock speed.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport of r42276
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42375 3c298f89-4303-0410-b956-a3cf2f4a3e73
There is a group of devices that lzma-loader doesn't work with. They
simply hang at "Starting program at 0x80001000" which is really hard to
debug and we didn't find any solution for this for years.
Broadcom doesn't use lzma-loader on these devices anyway. They decided
to drop lzma-loader and use less optimal LZMA compression that can be
handled by CFE itself (it doesn't use dictionary).
So support these devices we will need kernel compressed with different
parameters and trx without a loader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r42205
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42371 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Omnima MiniPlug RT5350 based board, 8MB SPI flash
Signed-off-by: Ivan Ignjatic<ivan@omnima.co.uk>
Backport of r42200
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42370 3c298f89-4303-0410-b956-a3cf2f4a3e73
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r42193
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42367 3c298f89-4303-0410-b956-a3cf2f4a3e73
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Backport of r42184
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42363 3c298f89-4303-0410-b956-a3cf2f4a3e73
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport of r42180
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42359 3c298f89-4303-0410-b956-a3cf2f4a3e73
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Backport of r42179
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42358 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.
Tested on hardware.
[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Backport of r42178
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42357 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42339
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42340 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42302
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42303 3c298f89-4303-0410-b956-a3cf2f4a3e73
we should check for ssb here.
backport of r42164.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42166 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
backport of: r42083
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42086 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42046
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42050 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42045
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42049 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42031 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: John Crispin <blogic@openwrt.org>
Backport of r42028
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42029 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a backport of bcma from wireless-tesing/master tag master-2014-07-29-1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
backport: r41899
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42020 3c298f89-4303-0410-b956-a3cf2f4a3e73
Alexander Couzens
blogic
nbd
jogo
rmilecki
florian
hauke
jow
cyrus
