The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Backport of r42184
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42363 3c298f89-4303-0410-b956-a3cf2f4a3e73
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport of r42180
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42359 3c298f89-4303-0410-b956-a3cf2f4a3e73
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Backport of r42179
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42358 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.
Tested on hardware.
[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Backport of r42178
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42357 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Steven Barth <steven@midlink.org>
Backport of r42158
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42355 3c298f89-4303-0410-b956-a3cf2f4a3e73
Utilize the new selective conntrack flushing facility to clear
out active conntrack entries referring to old IP addresses after
a firewall reload.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Backport of r42114
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42353 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable the separate feed repositories by default to align custom builds with the repositories
available on the snapshot download server.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Backport of r42112
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42352 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Luka Perkov <luka@openwrt.org>
Backport of r42111
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42351 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds default tx and rx antennas, so that LuCI shows automatic as the default radio option for the antennas.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport of r42085
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42350 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42345
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42347 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42344
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42346 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42339
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42340 3c298f89-4303-0410-b956-a3cf2f4a3e73
Backport of r42337.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42338 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42329
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42330 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42322
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42323 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42309
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42311 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42308
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42310 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42302
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42303 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42300
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42301 3c298f89-4303-0410-b956-a3cf2f4a3e73
A quite frequent problem after sysupgrading from an older, SSL enabled build
is that ustream-ssl is not installed so uhttpd fails to come up again due to
https listening directives in the preserved configuration.
Skip key/cert and ssl listen options when libustream-ssl.so is not present.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Backport of r42284
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42286 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r42257
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42258 3c298f89-4303-0410-b956-a3cf2f4a3e73
Disable MIPS16 to prevent it negatively affecting performance.
Observed was a increase of connection delay from ~6 to ~11 seconds
and a reduction of scp speed from 1.1MB/s to 710kB/s on brcm63xx.
Fixes#15209.
Backport of r42250.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42255 3c298f89-4303-0410-b956-a3cf2f4a3e73
we should check for ssb here.
backport of r42164.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42166 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a bug revealed in r41830.
First, the static variable `char nif[IFNAMSIZ]` of nl80211_phy2ifname()
would be zeroed out if the argument is "wlan0" or the like. This will
happen in the following call stack.
nl80211_get_scanlist("radio0", buf, len);
nl80211_phy2ifname("radio0") // return static var nif with content "wlan0"
nl80211_get_scanlist(nif, buf, len); // tail call
nl80211_get_mode(nif);
nl80211_phy2ifname(nif); // zero out nif
Later we try nl80211_ifadd("") which was supposed to create interface
"tmp.", but that won't happen because nl80211_msg() will put an invalid
ifidx 0 to the nlmsg.
Then iwinfo_ifup() and iwinfo_ifdown() would fail and happily
nl80211_get_scanlist() returned 0 and left *len undefined.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Backport of r42151
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42152 3c298f89-4303-0410-b956-a3cf2f4a3e73
When looking for the first ipaddr also consider the current prefix just
like network_get_ipaddrs6 does. If ipv6-address was empty the function
did not return the first ipaddr even if the list was non-empty.
fixes commit 83e9122f88a002871d5cdf421cf6aa6052b7e006
Signed-off-by: Henning Schild <henning@hennsch.de>
Backport of r42139
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42140 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
backport of: r42083
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/barrier_breaker@42086 3c298f89-4303-0410-b956-a3cf2f4a3e73
blogic
nbd
jogo
jow
cyrus
florian
hauke
