* [SMF] rename function s/gtp/gtp2/
* [SMF] Store GTPC version in session
So far we always depended on an xact being present in the code path in
order to know which kind of session it is (GTPv1C vs GTPv2C). Let's
instead store that information in smf_sess_t so that we have it always
available in an easy way.
* [SMF] Move smf_sess_t GTPv1C specifics into gtp substruct
* [SMF] Gy CCR: append 3GPP-NSAPI AVP
* [SMF] Append PDP-Address AVP to Gy CCR msg
* [SMF] Gy CCR: Move some AVPs under Service-Information/PS-Information
They belong there. Nokia infocenter documentation seems to be document
the possibility to configure its software to have it in top level, but
that's not what 3GPP TS 32.299 states, so let's stick to it.
* [SMF] Gy CCR: append 3GPP-PDP-Type AVP
* [SMF] Gy CCR: append 3GPP-Charging-Id AVP
* [SMF] Gy CCR: append SGSN-Address AVP
* [SMF] Gy CCR: append GGSN-Address AVP
In the past only GTPv2C was supported, and had the "gtp" generic prefix.
Later on, GTPv1C support was added, and "gtp1" prefix was used.
Let's move GTPv2C specific bits to have "gtp2" prefix too, and leave
"gtp" prefix for generic stuff among different GTP versions.
The use of the Gy interface (SMF acting as CTF towards an OCS node) is
mandated through configuration file. Default value "enable: auto" will
only make use of it in case a Diameter peer announcing support for the
Credit-Control Application is found.
Upon subscriber session creation, and after auth check over Gx, the SMF
will create a Gy session with the OCS and only after that step the SMF
will accept the session back to the subscriber.
The OCS may then grant some traffic volumes/time and ask to be notified
back with updated measurements.
In order to get the measurements, the SMF relies on PFCP URR configured
to the UPF through Session Repoort Request messages.
When closing the subscriber session, the SMF will also terminate the Gy
session at the OCS.
So far only some specifics parts of the Gy interface as well as the PFCP
side are implemented. Those should be enough to at least have
volume/time thresholds granted by the OCS, which then will be able to
track subsriber resource use.
This patch doesn't implement the OCS side of the Gy interface, that's
left as a future exercise. The interface was tested using an OCS
emulator implemented in TTCN-3 [1]
[1] https://cgit.osmocom.org/osmo-ttcn3-hacks/
TODO:
* Use an event for the report, like SMF_EVT_N4_TIMER?
* Properly set Service identifier in Gy CCR
* SMF: Properly set pkt/octet volumes in Gy CCR
** Update when receiving PFCP Modify Response.
* Figure out best way to require Gy through config file in open5gs-smfd.
* Create a new sess-sm.c which handles smf_sess_t state through
Gx+Gy+PFCP creation, modification and tear down. This way we can do
stuff in parallel, for instance Gx+Gy. It will alsoavoid duplicating
some code paths due to Gy being optional.
This commit adds required blocks in lib/diameter to be able to handle Gy
messages later in open5gs apps.
The Gy interface is mainly decribed in 3GPP TS 32.299 and 3GPP TS
32.251, which in turn refers to Diameter protcols defined in RFC4006.
This interface allows charging managment through an external OCS node.
The "Report Triggers" is sent SMF->UPF to tell in which situations a
report should be sent.
The "Usage Report Trigger" is sent UPF->SMF to indicate which situation
triggered the report.
* [PFCP] Fix trailing whitespace in message generation files
* [PFCP] message gen: Support multiple URR ID IEs in Create PDR group
* [PFCP] Support associating multiple URRs to a PDR
According to 3GPP TS 29.244:
"""
A PDR shall contain:
- zero, one or more URRs, which contains instructions related to traffic measurement and reporting.
"""
These will be further needed in PFCP in the future, as well as in other
Diameter based interfaces (such as Gy).
Let's put all implementation details in APIs so that devs don't need to
care about those details every time.
Alexander Couzens
root
Sukchan Lee
Pau Espin
EugeneBogush