ENABLE_DEVICE_NOISE is used only in two network drivers and is
otherwise unused. ENABLE_FLASH_NOISE is completely unused.
ENABLE_PARTITION_NOISE enables DEBUG in the partition command,
but this code has no debug messages at all.
Remove all this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On LAN9115/LAN9117/LAN9215/LAN9217, external PHYs are supported.
Switch to external PHY based on hardware strap pin and/or override flags.
Also add a mask to platform data selecting external PHY address to be used.
Code based on linux/drivers/net/ethernet/smsc/smsc911x.c (fd9abb3d, d23f028a).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt phylib from linux
switch all the driver to it
reimplement mii bus
This will allow to have
- phy drivers
- to only connect the phy at then opening of the device
- if the phy is not ready or not up fail on open
Same behaviour as in linux and will allow to share code and simplify porting.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If pdata is NULL smc911x_probe will crash. Checking the zero initialized
priv->shift results in default configuration if pdata is not set.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the check need to be inverted
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
poll the READY bit in PMT_CTRL. Any other access to the device is
forbidden while this bit isn't set. Try for 100ms
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use linux kernel chip detection from 3.5
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
detect if the bus is swapped and report a 32bit drivers is used on a 16bit bus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
switch ipe337: to it at the same time to do not brake it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to replace them depending on the platform data.
So we can specify shift and reg io witdh (16bit/32bit)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this make the driver more readable
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this rework is done in order to add a phylib and allow to have phy driver support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
fixes:
drivers/net/smc911x.c:334:1: warning: "FLOW" redefined
In file included from include/asm/blackfin.h:33,
from include/asm/system.h:29,
from include/asm/bitops.h:33,
from include/linux/bitops.h:69,
from include/common.h:31,
from drivers/net/smc911x.c:29:
include/asm/cpu/defBF561.h:1654:1: warning: this is the location of the previous definition
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sascha Hauer
Alexander Shiyan
Andreas Pretzsch
Jean-Christophe PLAGNIOL-VILLARD
Jan Weitzel
Marc Kleine-Budde
Juergen Beisert
sascha
Sascha Hauer