There are several use cases where a redundant Linux system is needed. The
barebox bootchooser framework provides the building blocks to model different
use cases without the need to start from the scratch over and over again.
The bootchooser works on abstract boot targets, each with a set of properties
and implements an algorithm which selects the highest priority target to boot.
See the documentation contained in this patch for more information.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add 'fbtest' - a command to produce test patterns on a screen
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add 'hwmon' command which allows to display the readings of all
hardware monitoring sensors registered with Barebox.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a command to flip bits in a Nand flash. This is useful for
testing purposes to check if flipped bits are corrected and if the
driver returns the correct number of bitflips.
The command writes a configurable number of bitflips to a single Nand
page. If the -r option is not given the results are reproducible, so
calling the same command twice will revert the bitflips.
The command uses the raw read/write Nand operations which are probably
less tested than the regular read/write operations, so the command may
produce surprising results.
As of writing the command has been tested with the GPMI Nand driver and
the imx-nand driver with fixes posted.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
of_fixup_status enables or disables the status property of a
given node with a device tree fixup.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This tools can read/write to the extended CSD register of MMC devices.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This tool will help to measure the system performance.
Some SoCs haven't the possibility to route their clocks to the output pins.
So you can use dhrystone to get a feedback about the clock speed.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
spd_decode command is used for decoding and printing
in human-readable format the information found
in memory module SPD EEPROMs.
There is the decode-dimms program from i2c-tools linux
package (see http://www.lm-sensors.org/wiki/I2CTools)
just for the same purpose.
Though spd_decode source code is based on decode-dimms
perl code there is a difference.
Signed-off-by: Alexander Smirnov <alllecs@yandex.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dhcp/bootp was bound to the command functionality.
This patch splits the dhcp command.
We are now able to use bootp without a shell.
This patch adds also a check for environment variables and globalvar.
So only when ENVIRONMENT_VARIABLES and GLOBALVAR is set, all received
dhcp data will be stored.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
That can be used for digest calculation and verify
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as I'll add a new generic command named digest
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a framework to describe, access, store and restore a set of
variables. A state variable set can be fully described in a devicetree node.
This node could be part of the regular devicetree blob or it could be an extra
devicetree solely for the state. The state variable set contains variables of
different types and a place to store the variable set.
For more information see:
Documentation/devicetree/bindings/barebox/barebox,state.rst
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a command to explicitly restore the environment (or
parts thereof) from the default environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds (back) support for non volatile variables. Non volatile
variables are variables which are stored in the environment over
reboot. They are used in the same way as the global variables, but
with a 'nv' command and device. The variables are stored under
/env/nv/, one variable per file. Adding a nv variable automatically
adds a global variable with the same name. Changing a nv variable
also changes the same global variable, but not the other way round.
This allows for example to configure the username as:
nv user=sha; saveenv
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This command compares two files. It does not show the differences,
it only returns successfully if both files are identical and with
an error if they differ.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A lot of boards use display-timings nodes to define the timings of one or more
displays. This command makes it possible to list and select displays which are
defined in a device tree.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a buffer for log messages and a 'dmesg' command to
print the messages. The log buffer is implemented as log objects
rather than a string buffer. This makes it easy to implement
limiting the messages, cleaning the buffer and timestamping
the messages.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This framework handles a list of registered Firmware programming handlers
to unify a firmware programming interface by hiding the details how
to program a specific Firmware in its handler. This is created with FPGAs
in mind but should be usable for other devices aswell.
A user has two possibilities to load a firmware. A device file is create
under /dev/ which can be used to copy a firmware to. Additionally a
firmwareload command is introduced which can list the registered firmware
handlers and also to upload a firmware.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It's often useful to get some information about a barebox image
before starting or flashing it. This patch introduces barebox
Image MetaData (IMD). When enabled a barebox image will contain
a list of tags containing the desired information. We have tags
for:
- the barebox release (2014.07.0-00160-g035de50-dirty)
- the build timestamp (#741 Mon Jul 28 15:08:54 CEST 2014)
- the board model the image is intended for
- the device tree toplevel compatible property
Also there is an additional generic key-value store which stores
parameters for which no dedicated tag exists. In this patch it
is used for the memory size an image supports.
Since there is no fixed offset in a barebox image which can be
used for storing the information, the metadata is stored somewhere
in the image and found by iterating over the image. This works
for most image types, but obviously not for SoC images which are
encoded or encrypted in some way.
There is a 'imd' tool compiled from the same sources for barebox,
for the compile host and for the target, so the metadata information
is available whereever needed.
For device tree boards the model and of_compatible tags are automatically
generated.
Example output of the imd tool for a Phytec phyFLEX image:
build: #889 Wed Jul 30 16:08:54 CEST 2014
release: 2014.07.0-00167-g6b2070d-dirty
parameter: memsize=1024
of_compatible: phytec,imx6x-pbab01 phytec,imx6dl-pfla02 fsl,imx6dl
model: Phytec phyFLEX-i.MX6 Duallite Carrier-Board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Similar to the Kernel multi function this gadget driver is used
for creating a USB device with multiple functions. This is
created and removed with the newly created 'usbgadget' command.
Based on the options it creates combinations of DFU, fastboot
and serial USB functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The command 'devinfo' was first spitting out all devices, and then
also all drivers. This patch separates them into two commands,
'devinfo' as before, and also the new command 'drvinfo'
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The oftree command is overloaded. This adds a dedicated command
which only dumps devicetrees to the console so that the corresponding
functionality in the oftree command can be removed in the next step.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This config just turned on the compilation of digest.c (used by 'SHA1',
'sha256sum' etc), so name it accordingly.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* CMD_MEMORY was defined both in common/Kconfig and commands/Kconfig
* that symbol turned not a command on, but just the compilation of
commands/mem.c, so rename it accordingly
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Provide minimal regulator support. Only supported operations are enabling
and disabling regulators. Association of devices with their regulators is
limited to devicetree only. If regulator support is disabled the API expands
to static inline stubs so consumers can still use the API.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rework the current framework so that I/O mapped I/O resources are
also possible.
Signed-off-by: Michel Stam <michel@reverze.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Creating menus from the shell using the regular 'menu' command is rather
complicated. This adds a 'menutree' command which creates a menu from
a directory structure. In the directory structure each directory corresponds
to a single menu entry. The directory contains the following files:
title - A file containing the title of the entry as shown in the menu
box - If present, the entry is a 'bool' entry. The file contains a variable
name from which the current state of the bool is taken from and saved
to.
action - if present this file contains a shell script which is executed when
when the entry is selected.
If neither 'box' or 'action' are present this entry is considered a submenu
containing more entries.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The readf command is useful to read the content of a file into
a shell variable. It should be used for ascii content and thus
stops reading at all nonprintable characters including newline.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This replaces the 'boot' script in the defaultenv-2 with a command
with the same behaviour. A command gives more flexibility for future
externsions
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This new memtest can test the whole unused memory. The new memtest
command try to request the whole unused sdram regions on all banks and
run the mem_test routine from common/memtest.c on it.
The memtest command has only two parameters;
-i Amount of iterations, default 1, iteration of 0 is endless.
-b Set this to skip integrity check.(Do only a fast test for bus lines)
If MMU support is enable, memtest try to run memtest twice. The first with
cache enabled, the second with cache disabled.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We often encounter the situation where slow devices should not be
probed during startup since probing is slow and maybe unnecessary
for unused devices. With MMC we have the 'probe' device parameter,
for ata we have the same, for USB we have the 'usb' command. Overall
this is not very consistent.
With MMC there is the additional problem that the probe parameter
is attached to the logical device when we often have the information
which physical device we want to probe.
This patch adds a 'detect' callback for devices and adds a command
to detect devices and to list the devices which are actually detecable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As of now we have no way to manipulate individual bits of registers on the
command line. This introduces a memory modify command which allows this. It
has the syntax:
mm [OPTIONS] <adr> <val> <mask>
With [OPTIONS] being the usual memory command options (-b, -w, -l, -d <file>).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Normally in commands we have one file per command which is named like
the command itself. The memory commands are an exception to this. This
patch changes this by separating the memory commands. This also has the
effect that the memory commands can now be selected individually. Along
the way we add some Kconfig help text for the commmands.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Marc Kleine-Budde
Andrey Smirnov
Sascha Hauer
Teresa Remmet
Daniel Schultz
Alexander Smirnov
Wadim Egorov
Jean-Christophe PLAGNIOL-VILLARD
Teresa Gámez
Juergen Beisert
Antony Pavlov
Holger Schurig
Michel Stam
Alexander Aring