On the sam9x5 series we now support 1 or 2 macb.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
in commit commit f60f6c58e
atmel_mci: check for device id we use to address the right slot
the driver use the dev_id to detect the slot which is wrong on 9263 as we have
2 devices with 2 slots
use slot_b paramter to specify the slot as done in linux
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use ds3 for heartbeat and ds5 for dfu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
configure BP4 and BP3
use BP4 to start DFU mode at boot
if BP4 is pressed at boot time and maintain at least 5s the dfu is started
otherwise we boot normaly
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
by default boot from nand with the bootstrap as first stage
update the smc config for 9g20-ek
switch to defaultenv
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The environment partition was overlapping the Barebox partition in
those three Atmel boards. Saving the environment resulted in the
Barebox being overwritten.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The new MMU setup will need SDRAM base addresses and sizes.
For this reason convert the MMU enabled ARM boards:
- move mem setup to mem_initcall. This is early but
still makes sure that we already have the console available
- move MMU setup in this initcall temporary as after the mmu_init will generic
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow each arch to handle the boards more simply and depending on
there need
the env var BOARD will refer to the current board dirent
for sandbox as we have only one board the board dirent is arch/sandbox/board
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>