This makes the code mre readable
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can request a master usefull for the spi command
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On LAN9115/LAN9117/LAN9215/LAN9217, external PHYs are supported.
Switch to external PHY based on hardware strap pin and/or override flags.
Also add a mask to platform data selecting external PHY address to be used.
Code based on linux/drivers/net/ethernet/smsc/smsc911x.c (fd9abb3d, d23f028a).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 89dfe2d2af "mdiobus: do not scan
the bus at registration time" dropped the check for struct mii_bus
element phy_mask while scanning through all addresses.
Re-add this check.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Scanning the bus can take some time. If we do not need the ethernet
device, this is unnecessary, so delay the scan until the phy device
iactually is needed.
Andread Pretzsch: Fixup bug in scanning for all devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
this allow to do not provide block_isbad at mtd driver level
as example spi flash
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use irq pin as the pin is asserted untill we clear it
This will allow to do not poll on i2c which slow down barebox
If no irq_pin is provided fall back on i2c polling
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Switch to new environment and add the bootscripts needed for mmc. Also,
update defconfig for new environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Needed so that the linker can throw it away when unused. This is needed
at least on current master for being able to enable pbl support for omap3
boards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the mount command used to have the syntax 'mount <dev> <type> <mountpoint>'.
This was changed to the more Linux like behaviour which specifies the
type with the -t <type> option. If a newer barebox is run on a device
with an older environment the mount command no longer works. This patch
adds compatibility to the old behaviour.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds generic board support (CLEP7212, Linux ARM ID=91)
for CLPS711X-target.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a simple serial driver for CLPS711X architecture.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds new architecture (CLPS711X) into barebox.
The core-logic functionality of the device is built around an ARM720T
processor running at clock speeds up to 90 MHz.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on some system as the spi_transfer is not set to 0 if the rx_buf or tx_buf
are not used they are not set to NULL
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When booting fails we will be immediately be back into the menu,
so the error message can't be seen. Also, boot in verbose mode
since in interactive mode the last bit of performance is not that
necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The idea of having /env/init/* scripts was to make the configuration
more flexible and customizable for boards. It turned out though that
people (including myself) do not find the place where they should
change these settings.
So this patch brings back /env/config for defenv-2. The individual
env/init/* scripts are removed and their content is added to
/env/init/config-board. This makes the values from /env/init/config-board
the board specific defaults which can be overwritten in /env/config.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The added complexity of bootargs-ip-* and bootargs-root-* makes
understanding defenv-2 more complicated. remove them and open
code the scripts instead in their users.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is mostly an example and does not have a real use, so remove
it to not have it in each and every environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The same issue was fixed in the Linux kernel in commit
66ddfc6 (mx35: add a missing comma in a pad definition)
for 2.6.33-rc7.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
hush now prints the error value if a command returns a value < 0,
so do not return -1 (EPERM) when we encounter an unknown command.
Instead, return 1 so that hush is quiet.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox size is 384KiB
and for the official atmel release we need to rootfs at 8M
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ARM Linux only maps a single 1MiB section for the devicetree. This has
a 1Mib alignment, so we are not allowed to cross such a boundary. Align
the devicetree to the next power of two so that this never happens.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fixed devicetree may need more space than the original one.
We used to use 0x8000 here. Add a define for it to have the
space defined at a single place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
fec_init() initializes some bits important for phy access, so do
this before the mdiobus is registered. This fixes mdiobus support
on i.MX28 boards in RMII mode.
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Took the mx28evk defconfig, activated DMA and NAND, used savedefconfig;
this patch is the result.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While flash layout may be custom, at least the nand0-device is good to
have.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These routines can fail, add support for that. Also, put in missing
copyright headers.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the uImage support may generate a temporary file which ought to be deleted
after usage. Due to the wrong filename this never happened. Fix this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Test if we already found a phy device on an address earlier and return
it if it exists. This makes it possible to call mdiobus_scan multiple
times.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
edev->init is called at eth_register time unconditionally and is supposed
to initialize the ethernet hardware. Since it's called unconditionally
this could be done by the driver without having an additional hook.
Some drivers need their initialization done earlier since they also register
a mdiobus which does hardware accesses on registration time.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several i.MX boards (all i.MX6 boards) need to do some adjustments
to phy registers. If barebox itself does not use network, networking
won't work in the kernel if the kernel does not have the fixups. Connect
the phy at probe time so that these tweaks are done during probe so that
the kernel works without phy register tweaks. Also this has the effect
that the phy device is present and introspectable without doing fake
network transfers beforehand.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for a filetype detection command. It can be
used to print a filename on the console or to set a variable
with the detection result for use in shell scripts.
The command also has an option to print the known filetypes
so that a user knows what to match for.
Based on an earlier version from Jean-Christophe.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The filetype strings are not really suitable for shell scripts, so
add a shortname array of filetypes usable for shell scripts.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The console layer calls of_device_is_stdout_path for a new console. When
we are booting without devicetree then of_chosen is NULL which makes barebox
crash. Check for a NULL pointer in of_find_property to prevent this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to avoid issue with resource order
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches environment variables to use linux list. This is easier
to read. An additional plus is that the environment variables no longer
need an initcall, so malloc is the only requirement for them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jean-Christophe PLAGNIOL-VILLARD
Andreas Pretzsch
Sascha Hauer
Alexander Shiyan
Uwe Kleine-König
Wolfram Sang