The DS1307 has a square wave output pin, which can be used to output a
clock signal from the DS1307. Additionally, the DS1308 supports
configuring this pin as an input from an external clock source to
which it should sync itself.
Add support with OF device tree properties to configure these
settings. Supported features are using the clock pin as an output, an
input, the rate of the pin, and if it should be enabled on battery
backup power.
The driver does not check that the selected features are supported by
the clock chip being used. It is the designer's responsibility to
create a valid device tree node; the bootloader does not attempt to be
a device tree validator.
Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It becomes a common case that the Kernel is loaded from the filesystem
which later becomes the rootfs. This adds a possibility to let bootm
automatically append the root= option to the kernel command line. This
is done when global.bootm.appendroot is true.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some SoCs allow to store multiple boot images on a device in order to
improve robustness. This adds a -r option to barebox_update to indicate
we do not want to make an update but instead repair/refresh an existing
image. Handlers which want to support this feature must set the
BBU_HANDLER_CAN_REFRESH flag during registration.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The driver was imported from Linux 4.4.
Current implementation supports only XZ decompressor.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add some documentation about fastboot 'flash' command and some useful
example how to use it to boot an initrd.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add the following improvements:
- clarify commands vs. filesystems for network file transport protocols
- Beautify links with prosa text instead of standard headlines
- adapt 'devinfo eth0' parameter output to current code
- improve console texts
- add docs for netconsole.active
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Clarify that this is about the TFTP filesystem implementation, in
contrast to the tftp command.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This documentation snippet was already added to the tree, but not
included anywhere.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix this warning:
checking consistency... [...]Documentation/devicetree/bindings/mtd/m25p80.rst:: WARNING: document isn't included in any toctree
by including the document.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
'bootm' is the lowlevel boot command, in contrast to 'boot', which is
more highlevel.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Using NFS in conjunction with boot spec and the feature to let Barebox
auto generate a kernel command line must keep the options the NFS filesystem
was mounted in Barebox. This patch extends the kernel command line parameter
on demand if something different than the defaults are used.
The command:
barebox:/ boot nfs://myhost//root
expands to the kernel command line:
nfsroot=myhost:/root,v3,tcp
while the command:
barebox:/ boot nfs://myhost:2049//root
expands now to the kernel command line:
nfsroot=myhost:/root,v3,tcp,mountport=2049,port=2049
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current barebox,environment node only allows specifying a raw device or
partition to load an environment from. Some boards, like OMAP and
SoCFPGA, instead want to use a file located in a FAT filesystem.
Extend the device tree bindings with a new property 'file-path' that
will trigger this behavior.
This allows any board using this driver to get the env from a file or
from a raw device, instead of each machine type being either raw
device only or file only.
Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add some documentation about behaviour and setup of pstore/RAMOOPS.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds hmac support to the raw backend.
With this patch, modifications of the header or data of a state partition can
be detected, as the hmac woudln't match anymore. The hmac relies on a shared
secret, which is requested from the keystore, with keystore_get_secret() using
the name of the state partition as the "name" of the secret.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add semihosting API implementation and implement a filesystem driver
to access debugging host filesystem using it.
Tested on Freescale SabreSD board (i.MX6Q) using OpenOCD
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We could only point to partitions in the device tree by using
&norflash, "partname:barebox-environment". Allow to point to the
partition directly without having to parse the partition labels.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some SPI NOR flashes support 4K erase blocks. 4K erase blocks do not
work with UBIFS which needs a minimum erase block size of 15360 bytes.
Also bigger sectors are faster to erase. This patch adds a device tree
option to use the bigger blocks instead of the default 4K blocks.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This adds the new barebox logo to the tree. This is added as svg
image which is converted to different png images during build time. The logo
can be found under /logo/barebox-logo-<width>.png in the running barebox.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch realizes framebuffer console support for barebox. It
supports colors and enough escape sequences to show the barebox
console and editor properly.
fbconsole mini-HOWTO
====================
1. compile sandbox barebox with
CONFIG_VIDEO=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_DRIVER_VIDEO_SDL=y
2. run barebox
3. test fbconsole
fbconsole0.active=oe
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This enabled multi image support for the Garz&Fricke Vincell board. Also
it adds the Vincell-LT as a second image with a separate device tree.
Previously we used the same image on both the Vincell and the Vincell-LT
image since the differences are not that significant for barebox. Still
this was good for quite some confusion internally, so let's properly
introduce a second image.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The previous patches changed the UBI naming and made automounting
UBIFS easier. Update the documentation accordingly.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch makes it possible to automatically add a suitable root= option
for booting Linux from the same filesystem on which the bootspec entry
has been found. This adds an additional 'linux-appendroot' option to
bootspec which if set to 'true' will cause barebox to automatically
add a root= option. This currently works for NFS, UBIFS and regular
block devices like ATA, SD/MMC using the root=PARTUUID= mechanism.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add the root= parameter for NFS filesystems. We currently hardcode
v3 and tcp which probably needs to become configurable at some point.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>