This will allow to drop the config.h and switch to multi board support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The macb/gem core is used by the Zynq SoC. In preparation of sharing
the macb driver between at91 and Zynq, rename the platform data to
'struct macb_platform_data', and move the definition to a common
location.
Signed-off-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we will add later the GMAC IP verion support (GEM)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to support multiple arch
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
switch gpio type from u8 to int in the data struct
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as in the kernel use is_rmii
flags for pinctrl
phy_flags for phylib flags
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the sam9x5 series we now support 1 or 2 macb.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
most of the board does not have a nor soldered
update the nand partition table to boot from nand with bootstrap
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The environment partition was overlapping the Barebox partition in
those three Atmel boards. Saving the environment resulted in the
Barebox being overwritten.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The new MMU setup will need SDRAM base addresses and sizes.
For this reason convert the MMU enabled ARM boards:
- move mem setup to mem_initcall. This is early but
still makes sure that we already have the console available
- move MMU setup in this initcall temporary as after the mmu_init will generic
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
before if you specify id = 0 the next available id will be taken
otherwise fail if already registered now as in linux we use -1
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this implementation is based on linux one (v2.6.35-rc5-76-gd0c6f62)
it will calculate all the clock dynamically instead of statictly
this will use also the new clock framework
it will also print the clock status after the console init
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow each arch to handle the boards more simply and depending on
there need
the env var BOARD will refer to the current board dirent
for sandbox as we have only one board the board dirent is arch/sandbox/board
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Josh Cartwright
Alexander Shiyan
Thomas Petazzoni