The macb/gem core is used by the Zynq SoC. In preparation of sharing
the macb driver between at91 and Zynq, rename the platform data to
'struct macb_platform_data', and move the definition to a common
location.
Signed-off-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we will add later the GMAC IP verion support (GEM)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
switch gpio type from u8 to int in the data struct
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as in the kernel use is_rmii
flags for pinctrl
phy_flags for phylib flags
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as the support atmel mci drivers does not work on rm9200 and we have the
possibility to use it as spi use it
Originally on rm9200 when the interface mci is in SPI mode we use a DataFlash Card
so allow it but if no dataflash card option is enable use as mmc spi.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This way you can specify as previously set the dhcp parameter via global.dhcp.xxx
and get the result via global.dhcp.xxx
This is need for the defaultenv-2 to add the bootp suppport.
Use it on defaultenv too to have only one set of var.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the sam9x5 series we now support 1 or 2 macb.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
set vendor-id to barebox-at91rm9200ek and the kernel over nfs
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As the mainline kernel does not enable the bootp support by default
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that we have a bootm command which boots everything we can
simplify the defaultenvironment. We can call bootm on every
image type and can remove the kernelimage_type variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The new MMU setup will need SDRAM base addresses and sizes.
For this reason convert the MMU enabled ARM boards:
- move mem setup to mem_initcall. This is early but
still makes sure that we already have the console available
- move MMU setup in this initcall temporary as after the mmu_init will generic
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Josh Cartwright
Jean-Christophe PLAGNIOL-VILLARD
Sascha Hauer
Alexander Shiyan