Patch adds gpio_to_desc helper for validate GPIO.
A bit optimization is performed (about -160 bytes on ARM).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Using the MXS MCI driver with an eight bit capable eMMC results into the
'devinfo' message the interface uses '0' bits for data transfer:
barebox:/ devinfo mxs_mci0
resources:
num : 0
start : 0x80034000
size : 0x00002000
driver: mxs_mci
bus: platform
Interface
Min. bus clock: 1476 Hz
Max. bus clock: 48000000 Hz
Current bus clock: 24000000 Hz
Bus width: 0 bit
The eight bit interface width is stored internally as value '2'. And a two bit
'2' ends up into 0xfffffffe when used as an array index. Using an unsigned
field instead fixes this issue:
barebox:/ devinfo mxs_mci0
resources:
num : 0
start : 0x80034000
size : 0x00002000
driver: mxs_mci
bus: platform
Interface
Min. bus clock: 1476 Hz
Max. bus clock: 48000000 Hz
Current bus clock: 24000000 Hz
Bus width: 8 bit
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
DISK_DRIVE is missing in Kconfig, so remove the "select" statement.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
EIO is a better error message to describe the data transfer to or from the SD cards has failed.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The host limits are only one limit we must honor when changing the transmission frequency.
The SD cards have their own limits, so take them also into account.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the SD card spec the detection can happen at 400 kHz
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since a generic block reset function is a available, also the MCI driver
should make use of it.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MMC_BUS_WIDTH_* macros do not correspond with the real bus width.
After setting a bus width larger than 1 bit the next call to change the
frequency ends in the default handler and the host interface stays silently
at the previous frequency.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove some leftover from former powerpc support which has no
relevance for i.MX based esdhc controllers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Linux expects linux,initrd-end to contain the first unused address. As
this doesn't match the end semantic used by barebox (i.e. end contains
the last used address) adding one is necessary.
Without this change Linux fails for me to correctly extract a gzipped
cpio archive provided as initrd.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the iomux-v3 (found on i.MX25,35,51,53,6) to pinctrl
support. The old SoC specific API is kept for compatibility. The
pinctrl devicetree support is enabled automatically when OFDEVICE
support is available.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a massively stripped down pinctrl support. The upper API
consists of only of:
int pinctrl_select_state(struct device_d *dev, const char *state);
This is used to setup the pinmux for a device to a certain state.
This function normally does not need to be called manually. The
device core will setup the default state before probing a device.
The pinctrl core has the job of handling the devicetree. It parses
the pinctrl phandles for a device from devicetree, finds the correct
pinctrl device and calls its set_state callback with the pinctrl
setup device node.
The simplicity of this pinctrl framework comes from the fact that
we:
- Limit usage to devicetree only for now. For non devicetree use the
old legacy SoC specific APIs still can be used.
- Do not parse the devicetree into internal data structures which
are used by the drivers later. This adds the overhead that we
may parse the devicetree multiple times for more dynamic setups,
but on the other hand we do not need to parse devices from the
devicetree we don't use in barebox
- Do not detect resource conflicts. Since the framework mainly is
a devicetree parser this would be hard to implement. It should
be easy for board maintainers to avoid resource conflicts though.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rename "drivers/gpio.c" to "drivers/gpiolib.c".
Reason is for understand functionality of driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
pass a struct cdev instead of the cdev name to of_parse_partitions.
This is available to the caller anyway and makes it easier to use
additional stuff from the cdev (like knowing whether it's a mtd
device).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The phandles have to be parsed completely before registering the devices
from the devicetree. Otherwise drivers can't rely on of_find_node_by_phandle
in their probe.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Taken from the Linux kernel, simplified and reworked to match barebox.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
actually ops.ooboffs is not defaulted so when its value gets
added to chip->oob_poi in nand_fill_oob or nand_transfer_oob
the respective memcpy is using a wrong address.
With this patch, both md -s /dev/nandraw0 and cp xyz /dev/nandraw0.sb
are working fine on an i.MX28 target (instead of crashing the board).
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Alexander Shiyan
Juergen Beisert
Jean-Christophe PLAGNIOL-VILLARD
Antony Pavlov
Uwe Kleine-König
Lucas Stach
Eric Bénard