This configuration can be used to use barebox as
x-loader replacement.
Also the ECC-Mode is changed from SOFT to BCH8.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add reset to gpmc_generic_init as proposed by TRM.
This also fixes some strange timing issue while GPMC Initialization for
NAND OMAP4460
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without yet adding in the underlying code, extend the revision
checking code to return additional values for PandaBoard ES boards.
Much of the code was taken close to verbatim from U-Boot.
compile tested, and confirmed that this code behaves identically to
the original panda configure and build for the three pandas i have:
* Rev A2 (boots)
* Rev EA3 (boots)
* Rev B1 ES (no output)
so while there's still work to be done, this at least represents the
necessary infrastructure to start *recognizing* panda ES boards.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a OMAP4 specific GMPC nand config for pcm049 and phyCARD-A-XL2 to increase
performance. Also add the possiblility to pass a board GPMC nand config.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for omap4 based Phytec phyCARD-A-XL2 board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current message indicating that SD card isn't
mounted is misleading if the card has only one
partition.
Updated the message to indicate that mounting
the specific partition failed.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove what is an apparently valueless Kconfig variable HAS_OMAP_NAND.
A search of the entire source tree shows:
$ grep -r HAS_OMAP_NAND *
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig:config HAS_OMAP_NAND
arch/arm/configs/phycard_a_l1_defconfig:CONFIG_HAS_OMAP_NAND=y
$
where the definition of that variable is simply:
config HAS_OMAP_NAND
bool
so it seems pretty clear it can be removed as nothing is using it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without the proper OMAP3 or OMAP4 dependency directives, you get the
wrong list of choices displayed based on which OMAP variant you pick.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
board_init was moved to pure_initcall. broken since:
commit 0adce7ec68
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Sun Jan 15 21:11:17 2012 +0100
ARM omap3: move board_init to pure_initcall
board_init initializes the mux and sdram. For both there is no
need to configure this so early. Move the code to a pure_initcall
and remove the surrounding unneeded code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function consists of only inline asm statements, so
use assembly in the first place. Also makes sure that the
function is compiled in arm mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
No need to do this so early. We can't print anything right
now anyway, so there is no need to setup vectors.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
There is no need to call a_init before relocation, so rename
the function to omap3_core_init and call it from board code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
board_init initializes the mux and sdram. For both there is no
need to configure this so early. Move the code to a pure_initcall
and remove the surrounding unneeded code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
The X-loader startup relocates to SRAM anyway, so there
is no need to be runnable from flash for the clock code.
This config is disabled in all defconfigs anyway, so remove
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
this will allow to switch omap3 to standard organisation
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable the flag HAVE_NOSHELL to allow first stage
bootloader to be built for this board.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support the setup of the mmc voltage, when booting OMAP4 with twl6030
from nand.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added i2c support for omap4. Tested on pcm049.
Driver based on linux kernel implementation.
Also added a shift to access 16-bit registers
to make support for OMAP730/850 possible.
If accessing a non existing slave the bus will go into arbitration mode.
It's unable to recover from it.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, there are multiple definitions of run_shell()
for each board that can be build in "xload" configuration.
Now there is only one function used by all boards.
The functions defined in xload.c are used only when "xload"
configuration used; but it gets compiled unconditionally.
This has been fixed as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This helper function can be used for automatic
SDDR configuration based on register settings
made by a previously first stage bootloader
i.e. x-loader.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add platform data to specify maximum frequency of hsmmc interface
which can be restricted due to external level shifters.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use generic read/write depending on the memory size
if no reg_read/write defined
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
If OMAP4 fall back to MMC1 boot in bootmode 0x39 (NAND,USB,UART,MMC1)
NAND and MMC bit in TRACING_VECTOR3 are set. With changed order it will
detect boot from MMC.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add some common xload helper functions to determine the boot source
on omap3/4 and to load images from mmc and nand.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Teresa Gámez
Juergen Kilb
Jan Weitzel
Antony Pavlov
Alexander Shiyan
Robert P. J. Day
Sanjeev Premi
Jean-Christophe PLAGNIOL-VILLARD
Alexander Aring
Daniel Mack