The doxygen documentation is long outdated. Remove it. It will
be replaced with sphinx based documentation later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As the place for the atags now is determined automatically the call
from the boards can be removed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With multiboard support the compiletime generated BOARDINFO string
gets more and more meaningless. This removes it from Kconfig and
replaces it with a variable that can be set at boardlevel.
Also many boards have a standard setting for the hostname in the
environment. This patch also moves the standard to C code by calling
barebox_set_hostname().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some boards have board specific special clock setups. These are now
done in the SoC specific clock drivers.
It is assumed that most board specific clock setup is done based on
copy/paste from U-Boot. The generalized clock setup differs from
some boards:
- ioclk are adjusted to 480MHz
- ssp clocks are adjusted to 96MHz
- enet out clock is enabled
Some boards adjusted the ioclk to 320MHz and the ssp clock to 160MHz.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use MMC_CAP_ names instead of MMC_MODE_. This makes it more
clear that these are capabilities of host/card and do not refer
to the current mode. These are in line with the Linux Kernel
except for MMC_CAP_MMC_HIGHSPEED_52MHZ which could be fixed
later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- enable the USB OTG device in gadget mode
- tested on i.MX23 EVH rev B1 with DFU
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- this patch fix MCI support and enable using the SDCard to store
the environment.
- it is fully copied from imx23-olinuxino.c
- tested on i.MX23 EVK RevB1
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Using SSP1 since this is the default configuration.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The new MMU setup will need SDRAM base addresses and sizes.
For this reason convert the MMU enabled ARM boards:
- move mem setup to mem_initcall. This is early but
still makes sure that we already have the console available
- move MMU setup in this initcall temporary as after the mmu_init will generic
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add a helper function for boards to register their memory
devices. This makes the board code smaller and also helps
getting rid of map_base and struct memory_platform_data.
And switch all of the memory to it
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
we keep struct memory_platform_data for now on we will switch off the memories
resources to struct resource
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Sascha Hauer
Eric Bénard
Wolfram Sang
Jean-Christophe PLAGNIOL-VILLARD
Juergen Beisert