Correct formatstring of size_t is %zu otherwise we get:
fs/bpkfs.c: In function ‘bpkfs_probe’:
fs/bpkfs.c:440:3: warning: format ‘%d’ expects argument of type ‘int’,
but argument 5 has type ‘size_t’ [-Wformat=]
dev_dbg(dev, "%d: offset = %d\n", i, d->offset);
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- declare the rigth mux for the GPIO used to enable the USB's 5V
- enable USB host controller
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ usb -f
USB: scanning bus for devices...
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
Using index 0 for the new disk
Bus 002 Device 003: ID 0951:1654 DT R500
Bus 002 Device 002: ID 0000:0000 EHCI Host Controller
3 USB Device(s) found
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- configure the MC34708 properly so that USB can work
(the sequence is taken from u-boot)
- add the required defines to the mc13xxx include file
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this allows SATA to work on i.MX53 QSB-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ ata0.probe=1
imx-sata 10000000.sata: port 0: SATA link ok
imx-sata 10000000.sata: port 0: Spinning up device...
imx-sata 10000000.sata: port 0: ok.
ata0: registered /dev/ata0
before this fix the log was :
barebox@Freescale i.MX53 Quick Start-R Board:/ ata0.probe=1
imx-sata 10000000.sata: port 0: SATA link timeout
set parameter: Connection timed out
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This re-syncs Marvell Dove and Solidrun CuBox DT files with current
files from Linux v3.14. Since barebox specific properties are now
kept separated, we don't need to tweak them anymore.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To ease DT import from Linux, which is still maintained in-tree, we
separate barebox-specific changes by including the original dts in
a separate DT file. This allows to overlay modifications and keep
clean DT history.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a driver for the Ethernet ip found on Marvell Orion SoCs,
which is derived from Marvell Discovery System Controllers (MV643xx).
It is partially based on the corresponding u-boot driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a driver for the mdio bus found on Marvell Orion SoCs as
part of the GBE device and Marvell Armada 370/XP as part of Neta
eth device. Both drivers can share this code, so make it available
independently.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This imports the Marvell mbus driver from Linux. The mbus is the
main downstream bus found on all Marvell Orion SoCs. The driver
deals with re-configurable address windows which are currently
parsed from DT. Also enable the driver as default on all MVEBU
SoCs. While at it, also reorder drivers/bus/{Kconfig,Makefile}
alphabetically.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This implements a of_phy_device_connect to allow DT enabled drivers
to connect to a PHY device by using the PHY's DT node only. It
currently assumes that each PHY node is a child of the corresponding
mdio bus.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This reorders Kconfig and Makefile for drivers/net alphabetically.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows to use unfs3 on the server side which doesn't integrate into
portmap/rpcbind which results in the port not being impossible to lookup
via rpc calls to the portmap program.
Use it like:
mount -t nfs -o port=2703,mountport=2703 192.168.77.157:/root /mnt/nfs
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Similar to mount(8) the barebox command mount now supports passing a string
to the file system driver via -o.
This is used in the next commit to let the user specify port numbers for
nfs mounts.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This was tested against nfs-kernel-server and unfs3.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ntohl always converts 32 bits even on archs where sizeof(long) == 8.
"ntoh32" is a much more intuitive name here. Also the name of the 64 bit
variant that is also added isn't questionable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is needed for nfs3 support as some types became bigger compared to
nfs2.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While at it also fix the type of flen holding a string length
(int -> size_t).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of letting rpc_lookup_req set mount_port and nfs_port, let it
return the port found and let the caller use that information.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When a former transaction was aborted by hitting Ctrl-C the old reply might
still hang in the ethernet controller making all further transactions fail.
So just skip over old replies.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We're speaking rpc mount version 2 (i.e. the same version as the
implemented nfs protocol), so also specify that in the lookup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On some architectures (e.g. alpha, amd64, arm64, ia64, s390x, mips64)
sizeof(ulong) is 8 which made net_read_uint32 actually read too much and
even returned the wrong value on big endian machines.
(Note the second issue isn't that critical though, because the only
architecture from the list above that uses big endian byte order is s390x
...)
Also change the argument to void * because the pointer is not necessarily
properly aligned.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We assume it to be non NULL in other places, so
we are in much greater trouble if it actually is.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
free() already checks the pointer to be non
NULL. No need to do it again.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
enum imx_spi_devtype is used as index into an array of controller types.
This makes the controller type handling unnecessarily complicated. Just
drop the enum and instead of an array use different statically initialized
structs and referene them by name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This sets the id_table in the driver correctly so that the driver
can match to the various types of flashes, not only "m25p80".
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
This allows to load all the lowlevel init code, including the
uncompressor, inside SRAM and not just the bare init part. This is
useful when pbl is used as a first-stage bootloader but is loaded by an
external firmware.
Signed-off-by: David Vincent <freesilicon@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i2c/spi devices in the devicetree often come with a "vendor,device"
comaptible string. These do not match in barebox, so add a
device_match_of_modalias function which does exactly that.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Increase the malloc size so that larger debug Linux image can be loaded.
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A boot script is added to load DTB and Linux images for booting.
The init script starts the boot script after a 5s timeout window.
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This renames the Freescale and Phytec board directories and defconfig
files to a common naming scheme. The board directories are named
<vendor>-<board> and the defconfig files are named
<vendor>-<board>_defconfig. Also the DataModul realq7 is renamed to its
Marketing Name eDM-QMX6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Alexander Aring
Eric Bénard
Sebastian Hesselbarth
Uwe Kleine-König
Lucas Stach
Sascha Hauer
David Vincent
Cristiano De Alti
Alexander Shiyan
Renaud Barbier